Professional Documents
Culture Documents
358-010112-01 IVPA说明书-完整线路图
358-010112-01 IVPA说明书-完整线路图
358-010112-01 IVPA说明书-完整线路图
358-010112-01
Advantage ....................................................................................... 01
Product Overview............................................................................ 02
Product Overview...................................................................................... 02 High charging current,the max charging current can be 200A for IVPA10048 and
Product Overview...................................................................................... 03 180A for IVPA7548,170A for IVPA5048,120A for IVPA3524.
Connection diagram ................................................................................. 03 Wide range of AC input voltage:the range of AC input voltage can be 90-280V for
Specification ................................................................................... 04 IVPA7548 and IVPA10048, 80-140V for IVPA5048 and IVPA3524.It can be better
Specification.............................................................................................. 05 compatible with generator working.It is rare to have wide rang input voltage for the
power frequency inverter.
Front Panel ..................................................................................... 06
LCD Display lcons........................................................................... 07
Dry Contact Signal .......................................................................... 08
Wiring Diagram ............................................................................... 09
Wiring System for Inverter .............................................................. 10 .
In battery mode, it will present battery capacity.............................. 14
LCD Setting ..................................................................................... 15
Setting items...............................................................................................16
Setting items.............................................................................................. 17 .
Setting items.............................................................................................. 18
Fault Code Table.............................................................................. 19
Fault Code Table....................................................................................... 19 .
Warning Code Table ........................................................................ 20
Display Information......................................................................... 21
Display Information................................................................................... 22
MPPT charger controller match to the Inverter ............................... 23
MPPT charger controller match to the Inverter .................................... 24
IVPA7548 TYPE
12
13
IVPA10048 TYPE
IVPA3524 TYPE
12
13
IVPA5048 TYPE
12
13
IVPA3524 IVPA5048 IVPA7548 IVPA10048
3500VA 5000VA 7500VA 10000VA (1)Boost CC Stage: If A/C input is applied, the charger will run at full current
in CC mode until the charger reaches the boost voltage.
2800W 4000W 6000W 8000W (2)Boost CV Stage: the charger will keep the boost voltage in Boost CV
24V 48V 48V 48V mode until the T1 timer has run out. Then drop the voltage down to the float
voltage, when the charging current is lower than 20% setting value.
Sinusoidal(Utility or generator) (3)Float Stage: In float mode, the voltage will stay at the float voltage. If the
Teriminal connection L-N HOT1-HOT2
A/C is reconnected or the battery voltage drops below 24Vdc/48Vdc, the
charger will reset the cycle above.
170Vac±7V(UPS) 90Vac±7V(Appliances)
180Vac±7V(UPS) 100Vac±7V(Appliances)
280Vac±7V
270Vac±7V
280Vrms
04 05
L1 L2 L1 L2
Li
L1 L2 L1 L2
Li
L1 L2
L1 L2
06 07
Wiring Diagram
Dry Contact Signal
There is one dry contact (3A/250VAC) available on the rear panel. It could be used to deliver
signal to extemal device when battery voltage reaches waming level.
AC I/O Connection
IVPA7548/IVPA10048 Remove cover plate
AC AC AC AC
Power in Power out Power in Power out
《 《
220/240Vac(HOT1-HOT2) 110/120Vac(HOT1-N)
Input Output
HOT1 HOT2 HOT2 HOT1 N
AC AC
Power in Power out
《
110/120Vac(HOT2-N)
08 09
Split phase connection diagram for single unit. (Only valid for 7548/10048 models)
PV panels
Wiring System for Inverter
10
L1 L1
L2 L2
N
PE PE
Utility
Load
Single phase connection diagram for single unit. (Only valid for 3524/5048 models)
PV panels
11
L L
N N
PE PE
Utility
Load
Single Phase Parallel connection diagram for three inverters in parallel
(Only valid for 5048 model)
12
L
N
PE
L
N
PE
Utility
Load
13
L1
L2
L3
N
PE
L1
Utility
L2
L3
N
PE
Load
Output voltage 110V
14 15
09
10
52
26
external communication(default)
external communication
BMS Baud rate 2400 bit/s.
08
16 communication
setup BMS communication
BMS communication,
Baud rate 9600 bit/s.
09
16 17
Battery Please check the battery connector
27
disconnected
18 19
INV NTC is
32 Disconnected Please contact our engineer.
is abnormal
Heavy over
34 load or output Please refer to Fault 13 and15 handling.
short
Input Phsae
14
Abnormal
20 21
LOAD LOAD
L1 L1 L2 L2
L1 power L2 power
L1 power is 1.0KW L2 power is 1.0KW
MPPT
CPU software version 1.00
MPPT Charge Controller software version
( for MPPT Charge Controller Build-in )
22 23
24