Professional Documents
Culture Documents
BEE&IE QB model exam
BEE&IE QB model exam
Part –A
1. Mention the limitation of ohms law.
2. A series RLC has R = 25Ω, L = 0.221H and C = 66.3 μF with frequency of 60 Hz. Find
the power factor.
3. Define MMF.
4. List out different types of cable.
5. A 8 pole, DC generator has a simplex wave - wound armature containing 32 coils of 6
turns each. Its flux per pole is 0.06wb. The machine is running at 250rpm.Calculate the
induced armature voltage.
6. State the applications of various types of generators.
7. Write the difference between PN junction diode and Zener diode.
8. Collector region of transistor is larger than emitter. Why?
9. What is transducer? Give an example.
10. Give any two applications of smart sensors.
11. State Ohm’s law.
12. Two resistors connected in parallel across 200V supply take 10A from the mains. If the
power dissipated in one resistor is 800 W, find the value of the other resistor.
13. Define relative permeability.
14. List out different earthing methods.
15. What are the basic parts of a DC generator?
16. Mention the methods of starting of 3-phase synchronous motor.
17. What is a Bipolar Junction Transistor?
18. Give the applications of transistor in its three different configurations.
19. List out application of solenoid.
20. What is the basic concept of optical transducer?
Part –B
2.In a Series RLC circuit R=24 ohm, L=191 mH, C=66.3 µF given that the supply voltage is
240v, 60 Hz. Find the 1.Equivalent Impedance 2.Power Factor 3.Current 4.Power 5.Reactive
Power.
3. Use nodal analysis to determine the voltage across 5-ohm resistance and the
current in the 12 V source.
5.Explain the construction, operation and types of Miniature circuit Breaker with neat sketch.
12. Explain the working principle of single phase Half Bridge Inverter and Full Bridge Inverter
with input and output waveforms.
13. Explain the working of piezoelectric transducer with suitable sketch and write its
applications.
14. Discuss the construction and operation of a LVDT with suitable sketch.
15.Using Nodal method find current through 8-ohm resistor for the circuit given below.
16.Find 1.the current through 15-ohm resistor 2.Voltage across 18-ohm resistor 3. Power
dissipated in 7-ohm resistor in the circuit shown below.
17. For the circuit shown in figure, find the current flowing through 10-ohm resistor using mesh
inspection method.
18. Find the current through 2-ohm resistor in the network shown in figure by loop current
analysis and Nodal Analysis.
19. A 2Ω resister is in series with a parallel combination of three resistances 10Ω, 10Ω and
5Ω.If the current through the 5Ω resistor is 14A.What is the total voltage across the entire
circuit?
20. A coil of resistance 5 ohms and inductance 100mH is connected in series with a 200µF
capacitor across a 220v, 50Hz supply. Calculate 1.Inductive reactance 2.Capacitive reactance 3.
Impedance of the whole circuit in complex form 4.The current 5.Power factor 6.Total Power
7.Voltage across the coil and capacitor.
22.Explain the concept of self and mutual inductance with neat diagrams.
23.Discuss the role of circuit breaker under normal and faulty condition.
24. Explain the construction and working principle of a three phase alternator.
25. Determine the speed at which a 6 pole alternator should be driven to obtain a frequency of
60Hz.
28. Explain the operation of BJT in common base mode with its characteristics.
30. Explain the construction and working principle of Half-Wave Rectifier with input and
output waveforms.
31. Derive the expression for Ripple Factor and Transformer Utilization Factor for HWR.
33.Explain smart sensors with built in features. compare with conventional sensors.
34.Use Mesh analysis to determine the three mesh currents in the circuit of figure shown below.
35. Obtain the current in all the branches of the network in figure by Mesh method.