Professional Documents
Culture Documents
GSB-01,02 User Manual_EN Rev B 201712
GSB-01,02 User Manual_EN Rev B 201712
GSB-01,02 User Manual_EN Rev B 201712
GSB-01/GSB-02
USER MANUAL
Table of Contents
SAFETY INSTRUCTIONS ................................................... 4
OPERATION .................................................................... 23
Menu Tree Additions ............................ 24
Test Lead Connection ........................... 25
Start Up Procedure .............................. 35
Creating a Test Setup ........................... 37
Automatic Tests ................................... 51
Common Utility Settings ...................... 63
FAQ ................................................................................ 71
APPENDIX ...................................................................... 73
Fuse Replacement ................................ 73
Error Messages .................................... 74
Specifications ...................................... 75
Dimensions ......................................... 76
Declaration of Conformity .................... 78
INDEX............................................................................. 79
3
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
This chapter contains important safety
instructions that you must follow during
operation and storage. Read the following before
any operation to ensure your safety and to keep
the instrument in the best possible condition.
Safety Symbols
These safety symbols may appear in this manual or on the
instrument.
4
SAFETY INSTRUCTIONS
Safety Guidelines
5
GSB-01/GSB-02 Series User Manual
6
SAFETY INSTRUCTIONS
7
GSB-01/GSB-02 Series User Manual
8
GETTING STARTED
GETTING STARTED
This chapter describes the scanner box in a
nutshell, including its main features and front /
rear panel introduction. After going through the
overview, please read the safety considerations.
CAUTION 5.0 kVAC MAX.
HIGH VOLTAGE 6.0 kVDC MAX.
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL RETURN
POWER
Appearance ..................................................................... 13
GSB-01 Front Panel ................................................................................. 13
GSB-02 Front Panel ................................................................................. 13
GSB-01 Rear Panel ................................................................................... 16
GSB-02 Rear Panel ................................................................................... 16
9
GSB-01/GSB-02 Series User Manual
Lineup
The aim of these scanner boxes is to allow multiple DUTs to be
tested either concurrently or in sequence using the GPT-9800, GPT-
9900 or GPT-9900A safety testers. The scanner boxes are
particularly well suited for multi-point safety testing as well for
volume testing on factory floors.
The GSB-01 has connections for ACW, DCW and IR testing, while
the GSB-02 also includes support for GB testing.
Firmware Note
Please make sure the firmware is up to date before using the
scanner boxes. Please see the user manual to check the firmware
version.
GPT-9800: firmware version V3.0 or above
GPT-9900/9900A: firmware version V2.0 or above
Note: Throughout this user manual, the terms scanner box or GSB
will refer to either model (GSB-01, GSB-02) unless specifically
stated otherwise. GPT-9000 will refer to any of the GPT-9800, GPT-
9900 or GPT-9900A safety testers, unless stated otherwise. HV and
H will refer to High Voltage terminals, while LO and L will refer to
the return terminal.
Model Overview
10
GETTING STARTED
Main Features
11
GSB-01/GSB-02 Series User Manual
12
GETTING STARTED
Appearance
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO Indicator
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL RETURN
POWER
Return Terminal
Indicator
HIGH VOLTAGE
HI HI HI HI HI HI HI HI
HI-POT
LO LO LO LO LO LO LO LO
Return
IR
RETURN
PASS
Terminal/
CHANNEL 1 2 3 4 5 6 7 8 SENSE H SENSE L
FAIL
POWER GB Rx
SOURCE H SOURCE L
SENSE L
SOURCE L
Channel Pass/Fail Indicators SENSE H SOURCE H
13
GSB-01/GSB-02 Series User Manual
WARNING
USE EXTREME CAUTION.
Do not touch the HIGH VOLTAGE terminal
during testing.
14
GETTING STARTED
SOURCE H SOURCE L
The SOURCE H,
SOURCE L, SENSE H
and SENSE L terminals
are used for GB tests.
15
GSB-01/GSB-02 Series User Manual
RS232/ RS232/
HV1 HV2 CH1 CH3 CH5 CH7 IN OUT
SER. NO. LB
MAX. MAX.
RS232/OUT
GND
T 2A 250V
RS232/ RS232/
HV1 HV2 CH1 CH3 CH5 CH7 IN OUT
MAX. MAX.
CH7
RS232/OUT
HI-POT
IR
CH2 CH4 CH6 ENSURE THE POWER IS REMOVED FROM
RETURN THE INSTRUMENT BEFORE REPLACING THE FUSE
GB Rx AC 100
50/60Hz
240V
50VA MAX.
CH8
SENSE H SENSE L
SOURCE H SOURCE L
GND
SENSE H
T 2A 250V
16
GETTING STARTED
RS232/IN RS232/IN
These two RS232 interfaces are the
communication links between the
master (safety tester) to slave
(scanner box). They are also used to
RS232/OUT RS232/OUT
T 2A/250V
GND
GND Connect the GND (ground)
terminal to the earth ground to
ensure operational safety.
17
GSB-01/GSB-02 Series User Manual
Safety Considerations
Workplace Precautions
18
GETTING STARTED
19
GSB-01/GSB-02 Series User Manual
Operating Precautions
20
GETTING STARTED
21
GSB-01/GSB-02 Series User Manual
1. Ensure all test leads are not broken and are free
from defects such as cracks or splitting.
22
OPERATION
OPERATION
Menu Tree Additions ....................................................... 24
23
GSB-01/GSB-02 Series User Manual
PASS/FAIL result
MANU
no.
READY
# 0003 status
Hold
MANU/ V I EW Press Common Utility
AUTO status UTILITY Settings1
Press
Save the SCAN EDIT/ SCAN Configuration
configuration SAVE (MANU mode only)1
1 Press EDIT/SAVE to save settings, or ESC to cancel and return to the previous screen.
2 Press the STOP key twice for a FAIL result.
3 When in MANU mode, selecting MANU number 000 will enter the special manual mode.
4 The Sweep mode function is only accessible in the special manual mode.
24
OPERATION
25
GSB-01/GSB-02 Series User Manual
Safety Tester
START STOP
RETURN
REMOTE
HV cable
POWER
Return cable
CAUTION 5.0 kVAC MAX.
HIGH VOLTAGE 6.0 kVDC MAX.
Scanner box #1
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL RETURN
POWER
Scanner box #2
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL RETURN
POWER
Scanner box #3
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL RETURN
POWER
Scanner box #4
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL RETURN
POWER
26
OPERATION
27
GSB-01/GSB-02 Series User Manual
Safety Tester
GND
GPIB
AC
POWER MAX.
500VA
SER. NO. LB
MAX. MAX.
RS232/OUT
RETURN
CH2
Scanner box #1
CH4 CH6 CH8 ENSURE THE POWER IS REMOVED FROM
THE INSTRUMENT BEFORE REPLACING THE FUSE
AC 100
50/60Hz
240V
50VA MAX.
RS232/OUT
Return Return
GND
RS232/IN
T 2A 250V
HV2 HV1
HV1 INPUT HV2 CH1 CH3 OUTPUT CH5 CH7
HIGH VOLTAGE HIGH VOLTAGE
RS232/IN
5.0 kVAC 5.0 kVAC
6.0 kVDC 6.0 kVDC
SER. NO. LB
MAX. MAX.
RS232/OUT
RETURN
CH2
Scanner box #2
CH4 CH6 CH8 ENSURE THE POWER IS REMOVED FROM
THE INSTRUMENT BEFORE REPLACING THE FUSE
AC 100 240V
50/60Hz 50VA MAX.
RS232/OUT
GND
RS232/IN
T 2A 250V
SER. NO. LB
MAX. MAX.
RS232/OUT
RETURN
CH2
Scanner box #3
CH4 CH6 CH8 ENSURE THE POWER IS REMOVED FROM
THE INSTRUMENT BEFORE REPLACING THE FUSE
AC 100 240V
50/60Hz 50VA MAX.
RS232/OUT
Return Return
GND
RS232/IN
T 2A 250V
HV2 HV1
HV1 INPUT HV2 CH1 CH3 OUTPUT CH5 CH7
HIGH VOLTAGE HIGH VOLTAGE
RS232/IN
5.0 kVAC 5.0 kVAC
6.0 kVDC 6.0 kVDC
SER. NO. LB
MAX. MAX.
RS232/OUT
RETURN
CH2
Scanner box #4
CH4 CH6 CH8 ENSURE THE POWER IS REMOVED FROM
THE INSTRUMENT BEFORE REPLACING THE FUSE
AC 100 240V
50/60Hz 50VA MAX.
GND
T 2A 250V
28
OPERATION
Connecting GSB-02
29
GSB-01/GSB-02 Series User Manual
ESC PAGE
Safety Tester
RETURN
START STOP
REMOTE
SOURCE H SOURCE L
MANU/AUTO EDIT/SAVE UTILITY
SOURCE H
SENSE H
SOURCE L
SENSE L
CAUTION 5.0 kVAC MAX.
HIGH VOLTAGE 6.0 kVDC MAX.
Scanner box #1
HI HI HI HI HI HI HI HI
HI-POT
LO LO LO LO LO LO LO LO IR
RETURN
PASS
CHANNEL 1 2 3 4 5 6 7 8 SENSE H SENSE L
FAIL
POWER GB Rx
SOURCE H SOURCE L
Scanner box #1
HI HI HI HI HI HI HI HI
HI-POT
LO LO LO LO LO LO LO LO IR
RETURN
PASS
CHANNEL 1 2 3 4 5 6 7 8 SENSE H SENSE L
FAIL
POWER GB Rx
SOURCE H SOURCE L
Scanner box #1
HI HI HI HI HI HI HI HI
HI-POT
LO LO LO LO LO LO LO LO IR
RETURN
PASS
CHANNEL 1 2 3 4 5 6 7 8 SENSE H SENSE L
FAIL
POWER GB Rx
SOURCE H SOURCE L
30
OPERATION
Safety Tester
GND
GPIB
AC
POWER MAX.
500VA
SER. NO. LB
MAX. MAX.
CH7
RS232/OUT
HI-POT
IR
GB Rx
RETURN
CH2 CH4
Scanner box #1 CH6
CH8
ENSURE THE POWER IS REMOVED FROM
THE INSTRUMENT BEFORE REPLACING THE FUSE
AC 100
50/60Hz
240V
50VA MAX.
SENSE H SENSE L
RS232/OUT
SOURCE H SOURCE L
GND
RS232/IN
SOURCE H
SENSE H
T 2A 250V
SOURCE L
SENSE L
HV1 INPUT HV2 CH1 CH3 OUTPUT CH5
HIGH VOLTAGE HIGH VOLTAGE
RS232/IN
5.0 kVAC 5.0 kVAC
6.0 kVDC 6.0 kVDC
SER. NO. LB
MAX. MAX.
CH7
RS232/OUT
HI-POT
IR
GB Rx
RETURN
CH2 CH4
Scanner box #2 CH6 ENSURE THE POWER IS REMOVED FROM
THE INSTRUMENT BEFORE REPLACING THE FUSE
AC 100 240V
CH8 50/60Hz 50VA MAX.
SENSE H SENSE L
RS232/OUT
SOURCE H SOURCE L
GND
RS232/IN
SOURCE H
SENSE H
T 2A 250V
SOURCE L
SENSE L
HV1 INPUT HV2 CH1 CH3 OUTPUT CH5
HIGH VOLTAGE HIGH VOLTAGE
RS232/IN
5.0 kVAC 5.0 kVAC
6.0 kVDC 6.0 kVDC
SER. NO. LB
MAX. MAX.
CH7
RS232/OUT
HI-POT
IR
GB Rx
RETURN
CH2 CH4
Scanner box #3 CH6 ENSURE THE POWER IS REMOVED FROM
THE INSTRUMENT BEFORE REPLACING THE FUSE
AC 100 240V
CH8 50/60Hz 50VA MAX.
SENSE H SENSE L
SOURCE H SOURCE L
GND
T 2A 250V
31
GSB-01/GSB-02 Series User Manual
DUT Connection
MAX. MAX.
CH7
Panel HI-POT
RS232/OUT
IR
CH2 CH4 CH6 ENSURE THE POWER IS REMOVED FROM
RETURN THE INSTRUMENT BEFORE REPLACING THE FUSE
GB Rx AC 100
50/60Hz
240V
50VA MAX.
CH8
SENSE H SENSE L
SOURCE H SOURCE L
GND
T 2A 250V
32
OPERATION
GB Output connection
HV1 INPUT HV2 CH1 CH3 OUTPUT CH5
HIGH VOLTAGE HIGH VOLTAGE
RS232/IN
5.0 kVAC 5.0 kVAC
6.0 kVDC 6.0 kVDC
SER. NO. LB
MAX. MAX.
CH7
RS232/OUT
HI-POT
IR
CH2 CH4 CH6 ENSURE THE POWER IS REMOVED FROM
RETURN THE INSTRUMENT BEFORE REPLACING THE FUSE
GB Rx AC 100
50/60Hz
240V
50VA MAX.
CH8
SENSE H SENSE L
SOURCE H SOURCE L
GND
T 2A 250V
DUT
DUT
GTL-116B GTL-116R
MAX. MAX.
RS232/OUT
GND
T 2A 250V
DUT
DUT
DUT
DUT
GHT-116R GHT-116B
33
GSB-01/GSB-02 Series User Manual
SER. NO. LB
MAX. MAX.
RS232/OUT
GND
T 2A 250V
GHT-116R
GHT-116B
DUT
DUT
DUT
DUT
DUT
DUT
DUT
DUT
34
OPERATION
Start Up Procedure
Startup
35
GSB-01/GSB-02 Series User Manual
Connection Check
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
Example C O MMO N U T I L I T Y
SCANNER BOX 1 : GSB - 0 1
SCANNER BOX 2 : - - - - - -
SCANNER BOX 3 : - - - - - -
SCANNER BOX 4 : - - - - - -
L CD BUZ Z I NTER CTRL SCAN
36
OPERATION
37
GSB-01/GSB-02 Series User Manual
Configure the
test settings for
the Selected
Manu test
Configure the
outputs of each
scanner for the
Selected test
38
OPERATION
MANU number
MANU = * * * - 0 0 2 MANU _ NAME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
0 100 kV mA ED I T
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB H I / L O T I MER
39
GSB-01/GSB-02 Series User Manual
A CW D CW I R GB
0 100 kV mA ED I T
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB H I / L O T I MER
cursor
40
OPERATION
41
GSB-01/GSB-02 Series User Manual
Not connected
In the example above scanner box#1 has ch1~7
configured as H and ch8 configured as L.
Scanner box#2 has ch1~8 configured as H.
42
OPERATION
43
GSB-01/GSB-02 Series User Manual
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
44
OPERATION
STOP
2. Press the STOP button to put the
tester into the READY status.
READY status
MANU = * * * - 0 0 2 MA NU _ N AME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV mA READY
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
START
4. Press the START button when the
tester is in the READY status. The
manual test starts automatically
and the tester goes into the TEST
status.
TEST status
MANU = * * * - 0 0 2 MA NU _ N AME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV 00 00 mA TEST
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
45
GSB-01/GSB-02 Series User Manual
Ch1 on Ch8 on
GSB-01 Multiplex Scanner Box
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL
0 100 kV 00 37 mA TEST
RAMP =000 . 1S T I ME R = 0 0 3 . 2 S
A CW D CW I R GB
STOP
Stop the Test 8. To stop the test at any time when it
is running, press the STOP button.
The test will stop immediately.
When the STOP button is pressed,
a judgment is not made on the test.
STOP status
MANU = * * * - 0 0 2 MA NU _ N AME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV 00 00 mA S TOP
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
46
OPERATION
STOP
9. To put the tester back into READY
status, press the STOP button
again.
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
47
GSB-01/GSB-02 Series User Manual
48
OPERATION
example HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL
Pass
STOP
Pressing the STOP button will
return the tester to the READY
status.
START
Pressing the START button will
restart the test.
49
GSB-01/GSB-02 Series User Manual
example 0 100 kV 01 37 mA FA I L
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
example HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL
Fail
STOP
4. The FAIL judgment will be held on
the safety tester display and the
scanner(s) until the STOP button is
pressed. Pressing the STOP button
twice will return the tester to the
READY status.
READY status
MANU = * * * - 0 0 2 MA NU _ N AME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV mA READY
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
50
OPERATION
Automatic Tests
This section describes how to create and run automatic tests for the
GSB-01/GSB-02 scanner boxes.
An automatic test comprises of up 16 MANU tests that are run
sequentially. In order to run an automatic test using the GSB-
01/GSB-02 scanner boxes, the scanner outputs for each manual test
must first be configured, and then each manual test in the automatic
test can be stepped through. In other words, the channel outputs
are directed by the manual tests that comprise the automatic test.
It is assumed that you have read and understood how to create an
automatic test on the GPT-9000 safety tester. If you are not sure
how to create and run an automatic test on the safety tester, please
see the GPT-9000 user manual.
51
GSB-01/GSB-02 Series User Manual
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
AUTO # 001~100
AUTO number
AUTO= 0 0 1 - 1 0 0 A U T O _ N AME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
0 100 kV mA ED I T
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB ADD
0 100 kV mA ED I T
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB ADD
52
OPERATION
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB ADD
53
GSB-01/GSB-02 Series User Manual
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
STOP
2. Press the STOP button to put the
tester into the READY status.
54
OPERATION
0 100 kV mA READY
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
START
4. Press the START button when the
tester is in the READY status. The
AUTO test starts automatically and
the display changes to TEST status.
Ch1 on Ch8 on
GSB-01 Multiplex Scanner Box
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL
55
GSB-01/GSB-02 Series User Manual
0 100 kV 00 37 mA TEST
RAMP =000 . 1S T I ME R = 0 0 3 . 2 S
A CW D CW I R GB
HOLD status
AUTO= 0 0 1 - 0 0 1 AU TO _ NAME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV 00 37 mA HO L D
RAMP =000 . 1S T I ME R = 0 0 3 . 2 S
A CW D CW I R GB
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL
Channel indicator
START
3. To continue to the next test after
HOLD is displayed on-screen,
press the START button.
56
OPERATION
STOP
4. To stop the test when HOLD is
displayed on-screen, press the
STOP button.
STOP
Stop a Running 1. To stop the AUTO test at any time
Test when it is running, press the STOP
button. The AUTO test will stop
immediately. When the STOP
button is pressed, a judgment is
not made on the current test and
any remaining tests are aborted.
AUTO= 0 0 1 - * * * AU TO _ NAME
#01 : FA I L # 0 2 : PASS # 0 3 : S TOP # 0 4 : - - - -
#05 : - - - - #06 : - - - - #07 : - - - - # 0 8 : - - - -
#09 : #10 : #11 : # 1 2 :
#13 : #14 : #15 : # 1 6 :
STOP
1. To put the tester back into READY
status, press the STOP button
again.
57
GSB-01/GSB-02 Series User Manual
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
58
OPERATION
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL
AUTO= 0 0 1 - * * * AU TO _ NAME
Example # 0 1 : PASS # 0 2 : PASS # 0 3 : PASS # 0 4 : PASS
# 0 5 : PASS # 0 6 : PASS # 0 7 : PASS # 0 8 : PASS
#09 : #10 : #11 : # 1 2 :
#13 : #14 : #15 : # 1 6 :
59
GSB-01/GSB-02 Series User Manual
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL
AUTO= 0 0 1 - * * * AU TO _ NAME
#01 : FA I L # 0 2 : PASS #03 : FA I L # 0 4 : PASS
# 0 5 : PASS # 0 6 : PASS # 0 7 : PASS # 0 8 : PASS
#09 : #10 : #11 : # 1 2 :
#13 : #14 : #15 : # 1 6 :
60
OPERATION
0 100 kV 00 37 mA PASS
RAMP =000 . 0S T I ME R = 0 0 3 . 2 S
A CW D CW I R GB
PASS/FAIL result
STOP
2. To put the tester back into READY
status, press the STOP button
(twice for a fail result).
READY status
AUTO= 0 0 1 - 1 0 0 A U T O _ N AME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV mA READY
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
61
GSB-01/GSB-02 Series User Manual
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
62
OPERATION
VIEW status
MANU = * * * - 0 0 0 MA NU _ N AME RE F # = 0 0 . 0 0mA
FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA
0 100 kV mA V I EW
RAMP =000 . 1S T I ME R = 0 0 1 . 0 S
A CW D CW I R GB
C O MMO N U T I L I T Y
I n t e r f a c e : RS 2 3 2
Baud : 115200
63
GSB-01/GSB-02 Series User Manual
64
REMOTE CONTROL
REMOTE CONTROL
Scanner Commands
GSB:CLR ................................................................................................... 65
GSB:SCAN ................................................................................................ 65
GSB<X>:CHANnel .................................................................................. 66
GSB:MEASure .......................................................................................... 67
GSB<X>:HI ............................................................................................... 68
GSB<X>:LOW .......................................................................................... 69
GSB:CLR Set
GSB:SCAN Query
65
GSB-01/GSB-02 Series User Manual
GSB<X>:CHANnel Query
12345678<cr><lf>
GSB-01:HXXHXXXX<cr><lf>
GSB-02:XLXXXLXX<cr><lf>
GSB-XX:XXXHXXXX<cr><lf>
GSB-XX:XXXHXXXX<cr><lf>
66
REMOTE CONTROL
GSB:MEASure Query
Description Returns the test results for the scanner boxes after
the test has completed.
12345678<cr><lf>
GSB-01:PXXPXXXX<cr><lf>
GSB-02:XFXXXFXX<cr><lf>
GSB-XX:XXXXXXXX<cr><lf>
GSB-XX:XXXXXXXX<cr><lf>
67
GSB-01/GSB-02 Series User Manual
Binary XXXXXXXX:XXXXXXXX:XXXXXXXX:XXXXXXXX
68
REMOTE CONTROL
Binary XXXXXXXX:XXXXXXXX:XXXXXXXX:XXXXXXXX
69
GSB-01/GSB-02 Series User Manual
70
FAQ
FAQ
• I get a scanner error when I run a test.
• The tester will stop testing midway through an automatic test.
• When I press the START button the tester will not start testing?
You may have PASS HOLD turned on or FAIL MODE set to HOLD.
Press the Start button to continue to the next test. See the user
manual for setting details.
When I press the START button the tester will not start
testing?
The tester must first be in the READY status before a test can be
started. Ensure the tester displays READY before pressing the
START button.
If “Double Action” is enabled, the START button must be pressed
0.5 seconds after the STOP button is pressed, otherwise the tester
will not start testing.
71
GSB-01/GSB-02 Series User Manual
72
APPENDIX
APPENDIX
Fuse Replacement
73
GSB-01/GSB-02 Series User Manual
Error Messages
Test Errors
The following error messages or messages may appear on the GPT
screen when configuring or running tests.
74
APPENDIX
Specifications
The specifications apply when the GSB-01/02 is powered on for at
least 30 minutes at 15˚C~35˚C.
Specifications
Scanner
Model GSB-01 GSB-02
High Voltage Rating 5kV AC/6kV DC 5kV AC/6kV DC
High Current Rating 40A AC
Number of HV channels 8 6
Number of GB channels None 2
System Interface RS-232 RS-232
Power Source AC 100-240V ±10%, 50/60Hz
Other
Operation Environment Indoor use, altitude up to 2000m
Ambient temperature 0°C to 40°C
Relative humidity 70%
Installation category II
Pollution degree 2
Storage Temperature & -10°C to 70°C, 85% RH
Humidity
Accessories GB wiring leads: GHT-109 x1 (only for GSB-02)
HV wiring leads: GHT-108 x1
Power cord x1
Quick start guide x1
User manual x1 (CD)
RS232C cable: GTL-235
HV test leads: GHT-116R x8(GSB-01), x6(GSB-02)
Return test leads: GHT-116B x1
GB H test leads: GTL-116R x2(GSB-02)
GB L test leads: GTL-116B x1(GSB-02)
Dimensions GSB-01: 330(W) x 101(H) x 399(D)
GSB-02: 330(W) x 101(H) x 413(D)
Weight Approx. 5.5kgs
75
GSB-01/GSB-02 Series User Manual
Dimensions
GSB-01
HI HI HI HI HI HI HI HI
LO LO LO LO LO LO LO LO
PASS
CHANNEL 1 2 3 4 5 6 7 8
FAIL RETURN
POWER
322.0 349.0
330.0 399.2
76
APPENDIX
GSB-02
HI HI HI HI HI HI HI HI
HI-POT
LO LO LO LO LO LO LO LO IR
RETURN
PASS
CHANNEL 1 2 3 4 5 6 7 8 SENSE H SENSE L
FAIL
POWER GB Rx
SOURCE H SOURCE L
322.0 349.0
330.0 412.6
77
GSB-01/GSB-02 Series User Manual
Declaration of Conformity
We
GOOD WILL INSTRUMENT CO., LTD.
declare that the below mentioned product
Type of Product: Multiplex Scanner Box
Model Number: GSB-01, GSB-02
satisfies all the technical relations application to the product within the
scope of council:
Directive: 2014/30/EU; 2014/35/EU; 2011/65/EU; 2012/19/EU
The above product is in conformity with the following standards or other
normative documents:
◎ EMC
EN 61326-1 Electrical equipment for measurement, control and
EN 61326-2-1 laboratory use –– EMC requirements (2013)
Conducted & Radiated Emission Electrical Fast Transients
EN55011: 2009+A1: 2010 Class B EN 61000-4-4: 2012
Current Harmonics Surge Immunity
EN 61000-3-2: 2014 EN 61000-4-5: 2014
Voltage Fluctuations Conducted Susceptibility
EN 61000-3-3: 2013 EN 61000-4-6: 2014
Electrostatic Discharge Power Frequency Magnetic Field
EN 61000-4-2: 2009 EN 61000-4-8: 2010
Radiated Immunity Voltage Dip/ Interruption
EN 61000-4-3: 2006 +A2:2010 EN 61000-4-11: 2004
◎ Safety
Low Voltage Equipment Directive 2014/35/EU
Safety Requirements EN 61010-1: 2010
EN 61010-2-030: 2010
GOODWILL INSTRUMENT CO., LTD.
No. 7-1, Jhongsing Road, Tucheng District, New Taipei City 236, Taiwan
Tel: +886-2-2268-0389 Fax: +886-2-2268-0639
Web: http://www.gwinstek.com Email: marketing@goodwill.com.tw
GOODWILL INSTRUMENT (SUZHOU) CO., LTD.
No. 521, Zhujiang Road, Snd, Suzhou Jiansu 215011, China
Tel: +86-512-6661-7177 Fax: +86-512-6661-7277
Web: http://www.instek.com.cn Email: marketing@instek.com.cn
GOODWILL INSTRUMENT EURO B.V.
De Run 5427A, 5504DG Veldhoven, The Netherlands
Tel: +31-(0)40-2557790 Fax: +31-(0)40-2541194
Email: sales@gw-instek.eu
78
INDEX
79