Professional Documents
Culture Documents
1466185086TS_ETC1H
1466185086TS_ETC1H
1466185086TS_ETC1H
Data Sheet
ETC 1H
refrigeration controller
Introduction
Features • ETC1H can control the cabinet temperature • Under voltage and over voltage compressor
directly protection (brown-out protection)
• ETC1H has low energy consumption • Pressure equalisation protection on starting
• 1 or 2 sensors (Air, evaporator) and optional the device or when voltage drops out
remote display can be connected (blackout protection)
• Using NTC temperature sensors • Diagnostics and self check of sensors and
• Temperature control independent of baro- potentiometer
metric pressure • Several defrosting methods can be handled:
• High accuracy combined with close differen- − Time controlled defrosting
tials and narrow tolerances ensures improved − Time controlled defrosting with
control evaporator sensor
• Built in timers enhances functionality − Temperature controlled defrosting
• Optional alarm for over or under temperature • Dual band control of outdoor bottle coolers
in both cold and warm – contact Danfoss for further info.
• Auxiliary relays: 5 Amp for heater, fan, light
etc. Eventually with delayed start or/and stop
DKRCC.PD.RM0.A2.02/ 520H5263 1
Data Sheet Electronic temperature control, type ETC1H
Approvals EMC tested to EN 55014, EN 55104, EN 6055-2, Ex approval IEC 9915 zone 2
EN 61000-3-2 and EN 610000-3-3 UL-C (UL + Canada), Semko Approvals
Parameters For customized ETC1H versions it is possible to Please contact Danfoss if you have questions or
adjust the following parameters in software. want to discuss a sample.
2 DKRCC.PD.RM0.A2.02/ 520H5263
Data Sheet Electronic temperature control, type ETC1H
Introduction
DKRCC.PD.RM0.A2.02/ 520H5263 3
Data Sheet Electronic temperature control, type ETC1H
Warm
cut-out
Cold
Default differential
cut-out Cold
cut-out
Variants There are many and almost unlimited ways of • You can have the ETC1H with standard soft-
using the ETC1H. ware or optionally with special customized
software for optimised functionality. Please
In order to optimize the efficiency and ensure the contact Danfoss regarding this.
reliability of the Danfoss products in your specific
applications and systems, always contact Danfoss Danfoss does not accept any responsibility for
prior to initiating the use of any Danfoss products. ETCs placed in environments outside our design
specifications. Use of the ETCs in such cases must
• You can have the ETC1H with optional 2 or 3 be verified via relevant field-tests, and always
relays, for controlling heaters, fans etc remains the responsibility of the buyer.
Temperature
W arm differential
C om pressor
C om pressor
cutout warm C old differential
position C om pressor
C om pressor
cutout cold
position
W arm differential
heat
cold differential
heat
Dual band control of compressor and cabinet heater for outdoor bottle coolers placed in cold
environment.
The controls can be mounted using the nut Please note: All Danfoss knobs have been
shown or it can be mounted using 2 screws type designed to sit flush against the housing,
EJOT DURO-PT dia. 3 × 7 mm. relieving the load on the spindle arm.
Maximum mounting force of knob: 80 Newton.
Warning: Whenever using non-Danfoss knobs, please
By using screw types different than the above ensure that they are mounted as described
mentioned, there is a risk of short circuiting the above and that the maximum mounting force of
line potential. knob: 80 Newton is not exceeded.
Danfoss Appliance Controls, DK-6430 Nordborg, Denmark, Phone: +45 7488 2222, Telefax: +45 7488 6995, www.danfoss.com