Professional Documents
Culture Documents
caterpillarcat330cexcavatorprefixjnkservicerepairmanualjnk00001andup-210518074419
caterpillarcat330cexcavatorprefixjnkservicerepairmanualjnk00001andup-210518074419
Models
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
i02344155
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
C 1P-1857 Retaining Ring Pliers 1
D 1P-0510 Driver Gp 1
E 1U-6396 O-Ring Assembly Compound 1
F 1P-1854 Retaining Ring Pliers 1
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. A reconditioning procedure should not be degraded
because of a low cost component such as an O-ring or a gasket. Use Tooling (E) during the
assembly procedure.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: Apply a light film of SAE 10W oil to all components before assembly.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 2/11(W)
Illustration 1 g00882512
Note: Bearing cup (27) must be fully seated. Bearing cup (27) must be properly seated in
order for the motor to assemble properly.
Illustration 2 g00882505
2. Rotate housing (3) . Use Tooling (D) in order to install seal (26) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 3/11(W)
Illustration 3 g00883246
4. Install shaft (2) and bearing cone (16) in a suitable press. Press bearing cone (16) onto shaft
(2) .
Note: Bearing cone (16) must be fully seated. Bearing cone (16) must be properly seated in
order for the motor to assemble properly.
Illustration 4 g00882894
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 4/11(W)
Illustration 5 g00882494
b. Rotate barrel assembly (19) . Install washer (23) and spring (22) . Place retaining ring
(21) on top of spring (22) .
Illustration 6 g00882927
c. Rotate the barrel assembly. Retain the contents of the barrel. Position guide (20) on
pins (24) .
d. Install shaft (2) and the bearing through the barrel assembly.
Illustration 7 g01163862
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 5/11(W)
Improper assembly of parts that are spring loaded can cause bodily
injury.
e. Install Tooling (A) and barrel assembly (19) into a suitable press.
f. Compress the spring. Use Tooling (F) in order to install retaining ring (21) .
Illustration 8 g00882451
Illustration 9 g00882324
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 6/11(W)
Note: Barrel assembly (19) is rotating group (14) upon the installation of the pistons.
Note: Place identifying marks on swashplate (17) in order to locate two holes on the top of
the swashplate.
Illustration 10 g00882976
Note: Splines in shaft (2) must engage splines in rotating group (14) .
Illustration 11 g00882984
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 7/11(W)
Illustration 12 g00882988
Note: The holes on the top of swashplate (17) must engage the dowels in housing (3) .
Illustration 13 g00882991
Illustration 14 g00882992
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 8/11(W)
11. Raise the temperature of sleeve (15) . Install sleeve (15) onto shaft (2) .
Illustration 15 g00882156
Illustration 16 g00882123
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 9/11(W)
Illustration 17 g00882112
Improper assembly of parts that are spring loaded can cause bodily
injury.
14. Install valve assembly (9) , sleeve (10) , and plug (11) into cover (5) .
Illustration 18 g00881963
15. Use Tooling (A) to install bearing cup (8) into cover (5) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 10/11(W)
Illustration 19 g00883138
Illustration 20 g00881953
Note: Take note of the slot in the reverse side of port plate (6) . The slot will receive the
dowel in cover (5) .
Illustration 21 g00881945
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 11/11(W)
Illustration 22 g00881939
End By: Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install ".
Copyright 1993 - 2020 Caterpillar Inc. Thu Sep 17 13:43:50 UTC+0800 2020
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 1/6(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
i02344156
Installation Procedure
NOTICE
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 2/6(W)
Illustration 1 g00883712
1. Position piston motor (23) into the bracket. Secure the piston motor with bolts (22) .
Illustration 2 g00883819
Illustration 3 g00883705
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 3/6(W)
Illustration 4 g00883690
4. Attach a suitable lifting device to the piston motor and fan assembly (17) . The weight of the
piston motor and fan assembly (17) is approximately 29 kg (65 lb). Position the piston
motor and fan assembly (17) . Install bolts (16) .
Illustration 5 g00883675
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 4/6(W)
Illustration 6 g00883666
Illustration 7 g00883641
7. Install tube assemblies (10) and (9) . Install bolts (12) and (11) .
Illustration 8 g00883636
8. Slide the hoses from tube assemblies (10) and (9) into position. Install hose clamps (8) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 5/6(W)
Illustration 9 g00883581
Illustration 10 g00883563
Illustration 11 g00883517
11. Install plates (1) , (2) , and (3) . Install the bolts.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 1/2(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
i04776349
Removal Procedure
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release" in this manual.
NOTICE
1. Drain the oil from the hydraulic oil tank into a suitable container for storage or disposal.
The capacity of the hydraulic oil tank is 175 L (46 US gal).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 2/2(W)
Illustration 1 g02883378
Illustration 2 g02879096
4. Remove nut (5). Remove gear (6), gasket (8), flange (9), key (10), and the O-ring seal.
Copyright 1993 - 2020 Caterpillar Inc. Thu Sep 17 13:45:42 UTC+0800 2020
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 1/3(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
i04959810
Installation Procedure
NOTICE
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 2/3(W)
Illustration 1 g02879096
2. Install key (10). Install the O-ring seal onto flange (9). Install flange (9), gasket (8). Install
gear (6) and nut (5).
Note: Do not tighten nut at this time. The gear pump must be installed on the engine before
the nut is tightened. This procedure will prevent the pump from being damaged internally.
Illustration 2 g02883378
4. Secure gear pump (4) into position with bolts and nuts (1).
5. Remove the front access cover (not shown) in order to tighten nut (5). Tighten nut (5) to a
torque of 80 ± 8 N·m (59 ± 6 lb ft).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
w 1/6(W)
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
i01796054
Removal Procedure
Illustration 1 g00739085
1. Remove the cover from the front of the console. Remove screws (1) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 2/6(W)
Illustration 2 g00739101
Illustration 3 g00739106
Illustration 4 g00739111
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17
w 3/6(W)
4. Reposition cover (6) in order to access the harness assembly on the right hand console.
Disconnect harness assembly (5) .
Illustration 5 g00739116
Illustration 6 g00739127
Note: Mark the location of locknut (10) and the handle for installation procedures.
8. Hold nut (11). Loosen locknut (10). Unscrew handle (9) in order to remove the handle.
Installation Procedure
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 2020/9/17