Professional Documents
Culture Documents
5d6dcacc17730
5d6dcacc17730
E-Series
SCR 電力控制器
SCR POWER CONTROLLER
說明書
INSTRUCTION
前言
閘 流 體 電 力控 制器 (SCR POWER CONTROLLER) ,
目 前 在 工 業 中已 被 廣泛 應用 於各 種電 力設 備中 , 諸
如 窑 爐 、 熱 處理 爐 、電 氣高 溫爐 、高 周波 機械 、 電
鍍 設 備 、 印 染設 備 、塗 裝設 備、 射出 機、 押出 機 等
等 , 然 而 因 為負 載 的不 同, 使用 環境 的限 制, 而 又
有 各 種 不 同 的控 制 模式 及各 種追 加配 備, 如相 位 控
制 (Phase Angle Control) , 分配 式零 位控 制 (Distrib
研 製 了P/E系列 各種 不同 控制 模式 之電 力控 制器 ,
以 滿 足 各 用 戶的 需 要。
P/E系 列SCR電 力控 制器 ,完 全採 用SCR POWER
MODULE密 封的IC化電 路板 ,使 整個 控制 器簡 單 輕
便 , 以 提 高 控制 器 的可 靠度 ,當 要使 用本 控制 器 時 ,
請 詳 讀 本 說 明, 以 了解 各種 控制 器的 結構 、功 能 、
接線方法。
謝 謝!
目錄
一、產品特點(Product features)
二、使用環境(Operation enviroment)
三、安裝(Installation)
四、負載測試(load test)
七、使用說明(Operation instruction)
1
一 、產品 特點 Product features
(1)全系列加裝高速保險絲,防止短路電流(di/dt)對SCR造
成損害。
The SCR unit attached with high speed fuse in order to prevent
the damage of SCR due to the shortage current(di/dt)
(2)全系列開模成型,體積小,安裝配線容易。
The unit is packagecd onstruction with less dimension,easy for
installation and wiring。
(3)多只LED燈顯示,遇到狀況立刻可判斷故障原因,迅速排除。
The causes of malfuntion can be indicated by individual LED
lamp,easy for trouble shooting。
(4)輸出特性呈線性,控溫精度高。
Less non-linearity output provides accurate control of temperature。
(5)高品質,高技術產品,絕無干擾現象。
High quality and high technical productions with no electrical
interference。
(6)性價比優。
Quilty and cost is all good。
二、 運 行環 境 Opearation enviroment
(1)-10~50℃,90%RH以下,不結露。
Ambient temperature:-10~50℃,Relative humidity:Max 90%。
三、 安 裝 Installation
(1)電力調整器,內部均會產生熱量,
安裝時請依據安裝方向安裝。
The SCR unit will produce heat
itself during operation,please
errect it upward according to
the instruction
(2) 控制箱須有空氣對流通風孔,請
依熱空氣由下往上之原理裝置通
風孔(或加裝抽風扇)
The parnel must be upward ventilated for hot air.
2
we recommand mounting a ventilating.
(3)請勿安裝於高溫或通風不佳之場所,否則請低於實際之70%
使用。
Do not install the unit in the space with high remperature and
poor ventilating,Do not operate the unit exceed70% of rated
output in case of above mentioned poor ambient conditions.
五 、控 制方式 及輸 出 波形
Control mode and output wave
135°PHASE ANGLE
LOW
POWER 25% 25%
OUTPUT POWER POWER
90°PHASE ANGLE
45°PHASE ANGLE
75% 75%
POWER POWER
HIGH
POWER
OUTPUT
100% 100%
0° 90°180°270°360° 90°180°270°360° POWER POWER
AC PHASE ANGLE
Fig 1 Phase Angle Power Control Fig 2 Distrlbuted Zero Crossover Power Fig 3 Time Proportioned Power Control
Control
六、LED燈顯示狀況及故障排除
LED lamp indication and trouble shooting
3
編號 顏色 顯示狀況 異常故障原因 處理對策
Treatment and
Pos.NO Color Indicating condition Causes of malfunction trouble shooting
1、檢查輔助電源電路
電源指示燈不亮 1、輔助電源未送電 Check the AUX.power
No indication of power No power of Aux.source. supply.
PWL 紅色 supply lamp 2、PCB基板故障 2、更換PCB基板或送修
Red Malfuntion on PCB board Repair or replace the PCB
(L1) (燈亮表示正常) 3、SCR超溫 board
Lamp lighting means Over remperature of SCR
3、檢查SCR超溫情形
normal Check the SCR temperature .
1、檢查TIC輸出信號
1、TIC輸出信號未輸出 Check the output signal
No output signal fromTIC of TIC
輸入指示燈不亮 2、TIC輸出信號極性反 2、檢查TIC輸出信號接線
Output signal from TIC is Reverse the connecting
IN 綠色 No indication of input
lamp
reverse. wiring of TIC.
Green 3、內部MAX或外部VR 3、檢查內部MAX及外部
(L2) (燈亮表示正常) 歸零 VR
Max value of internal Check the setting of
Lamp lighting means
output or External VR internal and external VR
normal
is zero setted . output
1、檢查IN燈,燈未亮表
輸出指示燈不亮 示TIC無l輸出信號或反接
No indication of output 1、無TIC信號或反接
lamp Check the lamp IN , NO
No output signal from TIC
or reverse the connecting indication means no
output singnal from TIC
OUT 黃色 (相位-燈亮表示正常) of output signal.
Phase angle control 2、IN燈有亮,OUT燈不亮
or reverse wired.
Lamp IN lighting and lamp 2、PCB基板故障,更換
Yellow
(L3) lamp lighting means
normal 或送修
OUT no indication .
Repair or replace the PCB
3、OUT燈亮,無電流輸出 board in case of the
(零位-閃爍表示正常) Lamp OUT lighting but no
Zero crossing control nalfunction from the board.
current output . 3、檢查主電源或保險絲
lamp blinks means
normal OUT no indication . Check main power supply
or fuse
SCR超溫指示燈燈亮 1、SCR散熱風扇故障或
1、更換風扇或清除異物
Over-temp of SCR lamp 卡住 Replace or clean the dirt
light Malfunctin or dirt blocking of the impeller.
ERR 紅色 on the ventilation fan
2、改善通風條件
Red (燈亮則表示異常) 2、周圍環境溫度過高或 Improve the ventilation
(L4) Lamp light means SCR 通風不良 condition
over temp High ambient temperature
or poor ventilation .
4
七 、 使用 說明 Operation instruction
SINGLE PHASE 50/60HZ PWL
AC220V
8
Input
如須加裝電磁開關時請置於負載側
The maguetic switch must be
installed load output
Ac1 Ac2 M + - E3 E2 E1
(2) 電壓,電流信號輸入,輸出百分比不可調。
Voltage,current signal with none VR. PCB source
AC220V
輔助電源
Input
6
(4) 自動手動切換控制,輸 Ac1 Ac2 M + - E3 E2 E1
(5) 多台連接,一台外部VR設定。
Multiple unit connecting with 1set external VR setting
Input
( 6 ) 多台連接,各自分別外部VR設定,本串聯接法最多只限
三台。
Multiple unit connecting with induvubual Wxter nal VR
setting , the connecting method is only suitable for less
than 3 installations .
Input
#其它特殊接線方式請與本公司技術服務部
For the other special connecting,please
contact with manufacturer
7