Professional Documents
Culture Documents
BNL - A318 _ A319 _ A320 _ A321 - TSM - 01-May-2024 - 73-20-00-810-864-A - Loss of T12 Sensor Signal Through the Channel B on Engine 2
BNL - A318 _ A319 _ A320 _ A321 - TSM - 01-May-2024 - 73-20-00-810-864-A - Loss of T12 Sensor Signal Through the Channel B on Engine 2
- ECU (4000KS)
- T12 temperature sensor
- harness HJ10
QT
REFERENCE DESIGNATION
Y
B. Consumable Materials
REFERENCE DESIGNATION
C. Referenced Information
REFERENCE DESIGNATION
Ref. AMM 73-21-50-000-043 Removal of the HJ10 Harness for SAC Engines
Ref. AMM 73-21-50-400-043 Installation of the HJ10 Harness for SAC Engines
3. Fault Confirmation
SUBTASK 73-20-00-710-144-A
A. Do the operational test of the FADEC 2B on the ground (with engine non motoring) Ref. AMM 73-29-00-710
-040.
4. Fault Isolation
SUBTASK 73-20-00-810-114-C
A. The failure message is generated if channel B input from the T12 temperature sensor is invalid or out of ra
nge.
(1) If the failure message T12 SNSR, J10, ECU is not confirmed:
- replace the T12 temperature sensor Ref. AMM 73-21-40-000-001 and Ref. AMM 73-21-40-4
00-001.
NOTE: Such a failure can be intermittent and therefore requires the replacement of the T12 tem
perature sensor as a first maintenance action.
(2) If the failure message T12 SNSR, J10, ECU is not confirmed but is repetitive:
- do the following procedure after the replacement of the T12 temperature sensor.
(a) Disconnect the harness HJ10 from the T12 temperature sensor (C102 connector) Ref. ASM
73-25-18:
- visually examine the receptacle and the connector for damaged pins and contamina
tion Ref. AMM 73-21-50-210-002.
1 If damage is found:
- repair or replace as required.
2 If no damage is found:
- do a cleaning of the connectors using a BRUSH - BRISTLED and stoddard sol
vent (Material Ref. CP2011) Ref. AMM 73-21-50-210-002.
(a) Disconnect the harness HJ10 from the T12 temperature sensor (C102 connector) Ref. ASM
73-25-18:
- visually examine the receptacle and the connector for damaged pins and contamina
tion Ref. AMM 73-21-50-210-002.
1 If damage is found:
- repair or replace as required.
2 If no damage is found:
- clean the connector and receptacle with a BRUSH - BRISTLED and stoddard
solvent (Material Ref. CP2011) Ref. AMM 73-21-50-210-002.
- do the electrical resistance test through the T12 temperature sensor betwee
n:
. pins 1 and 2 (160 to 250 ohms)
. pin 1 and the ground (>10 megohms).
- replace the T12 temperature sensor Ref. AMM 73-21-40-000-001 and Ref. A
MM 73-21-40-400-001.
a If damage is found:
- repair or replace as required.
b If no damage is found:
- clean the connector and receptacle with a BRUSH - BRISTLED and st
oddard solvent (Material Ref. CP2011) Ref. AMM 73-21-50-210-002.
- do the electrical resistance test through the harness HJ10 between:
. pins 18 and 19 (160 to 250 ohms)
. pins 18 and 7 (>10 megohms)
. pin 18 and the ground (>10 megohms).
SUBTASK 73-20-00-710-145-A
B. Do the test given in Para. 3.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.