Professional Documents
Culture Documents
Katranji RS-WS-N01-2D-LCD Industrial Wall-Mounted LCD User Manual
Katranji RS-WS-N01-2D-LCD Industrial Wall-Mounted LCD User Manual
1. product description
1.1product description
The product is an industrial wall-mounted high-protection grade enclosure, with a protection grade of IP65,
rain and snow proof and good air permeability. The circuit adopts American imported industrial-grade
microprocessor chips and imported high-precision temperature and humidity sensors to ensure excellent product
reliability, high precision and interchangeability. The output signal type is RS485, the farthest can communicate
2000 meters, the standard modbus protocol, supports secondary development.
1.2Features
1. Using high-precision temperature and humidity measurement unit, long-term stability and small drift
2. Using dedicated 485 circuit, standard ModBus-RTU communication protocol, communication address and baud
rate can be set
3.10~30V wide voltage range power supply
4. Easy to install, can be wall-mounted or rail-mounted
5. High anti-dust protection level (IP65)
6. LCD liquid crystal display, beautiful and generous
7. Buttons can set parameters, easy to operate
1.3The main technical parameters
DC power supply (default) DC 10-30V
Maximum power 0.4W
consumption
A precision humidity ±2%RH(60%RH,25℃)
temperature ±0.4℃(25℃)
humidity ±3%RH(60%RH,25℃)
B quasi-accuracy temperature ±0.5℃(25℃)
(default) -20℃~+60℃,0%RH~95%RH(Non-condensing)
-40℃~+120℃ default:-40℃~+80℃
Transmitter circuit operating 0%RH-100%RH
temperature and humidity
Probe working temperature Modbus-RTU letter of agreement
Probe working humidity 485 Signal
letter of agreement 0.1℃
1.4Equipment size
1.5system framework
1.6product model
Special Note:
1) There are certain specification requirements for 485 line field wiring. For details, please refer to the data package
"485 Equipment Field Wiring Manual".
2) When the device is connected to the 485 bus, ensure that the addresses of multiple devices will not be repeated.
Industrial Wall-mounted LCD Temperature and Humidity Transmitter (Model 485) User Manual V1.0
GND V-
485B 485-B
If the device address is less than 100, the decimal address is displayed at the display location of the device
address; if the device address is greater than 100, the hexadecimal address is displayed at the display location of the
device address.
3. Configuration software installation and use
3.1 Software selection
Open the data package, select "Debugging software" --- "485 parameter configuration software",
Industrial Wall-mounted LCD Temperature and Humidity Transmitter (Model 485) User Manual V1.0
(The device does not provide a communication line by default, the color of the line is for reference only)
3.2 parameter settings
①. Select the correct COM port (check the COM port in "My Computer—Properties—Device Manager
—Port"). The following figure lists the driver names of several different 485 converters.
② Connect only one device alone and power it on, click the test baud rate of the software, the software
will test the baud rate and address of the current device, the default baud rate is 4800bit/s, and the
default address is 0x01.
③. Modify the address and baud rate according to the needs of use, and at the same time, you can query
the current function status of the device.
④. If the test is unsuccessful, please recheck the equipment wiring and 485 driver installation.
Industrial Wall-mounted LCD Temperature and Humidity Transmitter (Model 485) User Manual V1.0
4. letter of agreement
4.1 Basic communication parameters
address co function co Register start ad Register lengt Check code l High bit of che
de de dress h ow bit ck code
Response frame (hexadecimal): (for example, the temperature is -10.1℃ and the humidity is 65.8%RH)
address c function cod Returns the n Humidity Temperatur Check code High bit of
ode: e umber of vali value e value low bit check c
Industrial Wall-mounted LCD Temperature and Humidity Transmitter (Model 485) User Manual V1.0
d bytes ode
Temperature calculation:
When the temperature is lower than 0 ℃, the temperature data is uploaded in the form of complement code.
Temperature: FF9B H (hexadecimal) = -101 => temperature = -10.1℃
Humidity calculation:
Humidity: 292 H (hexadecimal) = 658 => Humidity = 65.8%RH
5.Key operation instructions
Password input is possible (default password is 888),Long press again after input keyEnter the
main interface of settings, the password error prompts ERR.
2 ) After entering the setting main menu , short according or Page forward and backward , short
4)During the setting process, press Can abandon this setting,Press again Back to the main interface。
The specific parameter interface is as follows: