Professional Documents
Culture Documents
HYDROGENCOMPRESSOR
HYDROGENCOMPRESSOR
HYDROGENCOMPRESSOR
We summarize below the Diaphragm compressors data: Inlet Pressure: 10bar g., Discharge Pressure:
200bar g, Flow: 10Nm3/h
We have offered you a package with our VC1 Diaphragm compressor two stages, two cylinders.
This compressor will guarantee zero contamination and absolute purity as the gas at intake.
Inside the compressor, the gas wet parts will be in contact with only stainless steel.
The static seals of the diaphragm compressor guarantee a leak tight solution, with minimum gas
leakage.
We guarantee the entire system shall conform to CE/PED/ATEX European standards suitable for a
Zone 2 Atex area.
SEDE LEGALE VIA P.VERONESE 2 – 20145 MILANO – SEDE OPERATIVA VIA TRAVERSI 3/5 – 20068 PESCHIERA BORROMEO
C.F e P.IVA 08171860961 – CAP. SOC. € 10.000,00 – REA: MI-2007257 – FAX +39 02 92879095 – TEL +39 02 87197090
ANNEXURE 1
COMPRESSOR PACKAGE
SEDE LEGALE VIA P.VERONESE 2 – 20145 MILANO – SEDE OPERATIVA VIA TRAVERSI 3/5 – 20068 PESCHIERA BORROMEO
C.F e P.IVA 08171860961 – CAP. SOC. € 10.000,00 – REA: MI-2007257 – FAX +39 02 92879095 – TEL +39 02 87197090
1.1 PERFORMANCE & ENGINEERING DATA
PROCESS CONDITIONS
Motor Rating (kW) 5.5 Exd IIC T4 Motor Speed (RPM) 1450
* Note: We reserve the right to make changes to the engineering specifications before finalization
of the contract. This data is indicative only.
SEDE LEGALE VIA P.VERONESE 2 – 20145 MILANO – SEDE OPERATIVA VIA TRAVERSI 3/5 – 20068 PESCHIERA BORROMEO
C.F e P.IVA 08171860961 – CAP. SOC. € 10.000,00 – REA: MI-2007257 – FAX +39 02 92879095 – TEL +39 02 87197090
Annexure 2. Scope of Supply
1 VC1-10/10-200 hydrogen compressor with the following components:
Complete enclosed frame
Heavy duty cast iron frame casting
Forced feed lubrication to all required parts
Oil pump driven by compressor shaft
Forged steel crankshaft, connecting rod and alloy steel piston rods
Water-cooled cylinder head
Triple diaphragm with leakage detection system to prevent any contamination
One sets of operation and maintenance manual in English language
2. Compressor Package:
Suction strainer of stainless steel wire gauge 10micron
IP55 electric TEFC motor Exd IIC T4
Inter & after coolers
Pressure relief valve on each stage
switches on a local steel panel
• Low gas suction pressure
• High gas discharge pressure
• Low lubricating oil pressure
• Low cooling water flow
Gauge panel showing:
• Inter-stage gas pressure
• Oil pressure
Explosion proof solenoid valves (instead of pneumatic valve)
Note: We can add or change any extra instrumentation/controls as per your specific
requirement.
SEDE LEGALE VIA P.VERONESE 2 – 20145 MILANO – SEDE OPERATIVA VIA TRAVERSI 3/5 – 20068 PESCHIERA BORROMEO
C.F e P.IVA 08171860961 – CAP. SOC. € 10.000,00 – REA: MI-2007257 – FAX +39 02 92879095 – TEL +39 02 87197090