Professional Documents
Culture Documents
503671725 Lab Test Protocol
503671725 Lab Test Protocol
503671725 Lab Test Protocol
20 mm
Product Engineering
❷❹❺ Test Parameter Test Method Sample Construction Type Reporting Results Details
The force required to separate the upper ISO 20344 Whole Shoe 01
Rubber Outsole with EVA Midsole to
JM-110 Outsole Bond from the outsole or to separate adjacent BS 5131 Pair after 2.5 Kg
Fabric, Synthetic or Leather Upper
SATRA TM 411 48 hours
Peeling Strength Test layers of the outsole or to cause tear ISO 17708 Upper pull from the
failure of the upperor the sole is GB/T 21396 Outsole in specific Leather Outsole to Leather Upper 3.0 Kg
measured place
❸❹❺❽ Test Parameter Test Method Applicable Details Sample Cycles Reporting Results Details
Water Penetration Footwear size Visual assessment of Water Penetration
Footwear Flex Tester SATRA TM 77 between 6 & 12 1 Pair 15,000 Cycles and total area of water penetration
Water Proof
JM-102 Adults mm2.
Footwear Testing
Water Resistance Footwear size Visual assessment of Water Penetration
Dynamic Footwear Tester SATRA TM 230 between 1 and 14 1 Pair 5,000 Cycles and total area of water penetration
Adults mm2.
LEATHER
❸❼ Test Parameter Test Method Reporting Details Reporting Results Details
Dyed Textiles and Synthetic Leather:
The measurement of a leather or fabric’s performance Test from the American Association of Textile
Crocking AATCC 8-2001 Grade 1 - High Dry: 4.0 - Wet: 3.0 (minimum) Chemists and Colorists. This method uses a
when it is exposed to specific sources of ignition.
Degree of Color
JM-201 Dry & Wet Color ISO 105
standard white cotton fabric that is rubbed against
Transfer. the surface of the test material. To test for wet 5 4-5 4 3-4 3 2-3 2 1-2 1
Fastness Crocking means the transfer of color from one fabric SATRA 167 Print Textiles, Denim, Velvet Textiles crocking the standard fabric is wet before rubbing
Grade 5 - No against the material. Maximum Temperature of
to another by rubbing. ASTM D5053 color transfer Genuine or Suede Leather 60C°
Dry: 3.0 - Wet: 2.5 (minimum)
❸❼ Test Parameter Test Method Material Cycles Reporting Results Details
Flexing endurance test is a simple folding of the leather 45 x 70 mm The Bally leather flexing test is
JM-202 Bally Flex Endurance specimen several times with the grain side out with Satra STM 701 100,000 Cycles conducted till the piece of leather
help of a machine. Any change due to folding indicates or equivalent equipment Angle: 22.5° cracks.
poor flexing endurance.
MATERIALS
❸❺❻❼ Lab Test Test Method Reporting Results Details Pull laces
with the Dynamome ter
the material is measured only. Material in SATRA TM 162 Baumann Tear Leather Minimum of 10 Kg
Length and Width. Midsole 139.7 mm
❸❺❻❼ Test Parameter Test Method Standard Sample Cycles Reporting Results Details
1600 Cycles Satisfactory
25600 Cycles
❸❺❻❼ Test Parameter Test Method Standard Parts Reporting Results Details
The resistance of textile materials to abrasion Textile Used Outside The Shoe Minimum of 50 Cycles
Fabric Materials as measured on a testing machine in the Minimum of 120 Cycles
ASTM D3884 Cycles on the Stoll Textile Used Inside The Shoe
laboratory is generally only one of several
JM-306 Stoll Abrasion Test ASTM D3885 Abrasion Collar Linings Minimum of 300 Cycles
factors contributing to wear performance or
Equipment Minimum of 40 Cycles
durability as experienced in the actual use of Footbeds
the material Synthetics Minimum of 200 Cycles
❸❺❻❼ Test Parameter Test Method Standard Sample Cycles Reporting Results Details
Upper Mesh Test Xenon Arc Lamp Die cut matterial 12 Rating 5 No Change in Appearance
UV - Light Cm x 7.5 Cm
JM-309 Standard Light UV Lamp: UVA 340 Room Temperature of Rating 4 Slight Change in Appearance
Samples of Test Cycle Time: 24
Colors Phenolic Yellowing SATRA TM160 Textiles, Suedes hours Rating 3 Moderate Change in Appearance
Room Temperature: and Nubuck Rating 2 Marked Change in Appearance
Light Fastnes
23 ±2 C° Leathers Rating 1 Very Marked Change in Appearance
❸❺ Test Parameter Test Method Standard Sample Cycles Reporting Results Details
60 minutes Visual analysis observing the lack of
Matting agent with
Consists in determine the degree of formic acid SATRA TM 310 at shine when comparing with similar
Metal pieces pieces not use in the experiment.
JM-310 Upper Eyelets protection in final coating layers of ISO 22775 60 C°
ASTM B117
representing 1
Testing finishing varnish applied in metal pieces 5 minutes
Sulfite Corrosion ISO 9227 pair per batch Visual evaluation for stain formation and /
and corrosion than
Resistance or superficial darkening.
30 minutes
❸❺❻❼ Test Parameter Test Method Standard Sample Cycles Reporting Results Details
Leather Upper
Laminar Peel Stitched Leather
Determine the bonding strength of a
JM-311 Strength SATRA TM 411 Upper with Test Cycle Time: 24
laminated material through radio Instron Pull Tast
WTM 401 Laminated RF Hours after Welding
2.0 Kg Per Cm
frequency welding on the leather upper. Welding Material
Radio Frequency
Welding
KNITTED UPPERS
❸❺❻❼ Test Parameter Test Method Reporting Details Reporting Results Details
The measurement of a leather or fabric’s
Test from the American Association of Textile
Crocking performance when it is exposed to specific AATCC 8-2001 Grade 1 - High Chemists and Colorists. This method uses a
sources of ignition. Degree of Color standard white cotton fabric that is rubbed against
JM-501 Dry & Wet or Knitted Uppers
Transfer. the surface of the test material. To test for wet
Color Fastnes Crocking means the transfer of color ISO 105 Grade 5 - No Dry or Wet: 3.0 (minimum) crocking the standard fabric is wet before rubbing
5 4-5 4 3-4 3 2-3 2 1-2 1
against the material. Maximum Temperature of
from one fabric to another by rubbing. or color transfer 60C°
SATRA 167
❸❺❻❼ Test Parameter Test Method Material Cycles Reporting Results Details
Swing metal plate Visual Inspection for slight damage/cracking
Whole Shoe Flex at a rate of 140 Temperature of 23 ±2 C°
JM-502 Vamp Test Knitted Upper SATRA TM 25 cycles per minute Bending angle: 30° to 90° Dry Minimum: 500.000 Flex
with two artificial Time: 48 hours Wet Minimum: 100.000 Flex
foot.
❸❺❻❼ A method intended to determine the force Test Method Standard Sample Reporting Results Details
required to tear a material. Applicable to non- Six square test
JM-503 Tear Strength Test leather footwear upper and lining materials, specimens of 500 x
Trouser Leg Method but can be used with all types of thin flexible 100 mm. Minimum of 3.6 Kg
SATRA TM 30 Knitted Upper
materials. In the specific case of Knitted uppers
23 ± 2C°
tear is done along and across.
48 hours
❸❺❻❼ Test Parameter Test Method Standard Sample Cycles Reporting Results Details
Upper Mesh No worse than
12800 Cycles Satisfactory
DRY
JM-504 Abrasion Test slight wear / color 25600 Cycles Slight Color Contrast
Martindale Abrasion Test EN13520:2001
Standard contrast at 12800 3200 Cycles Satisfactory
cycles WET
6400 Cycles Slight Color Contrast
❸❺❻❼ Test Parameter Test Method Material Cycles Reporting Results Details 65
❸❹❺❼ Test Parameter Test Method Material Cycles Reporting Results Details
Rubber Outsole
Tested through 84 Maximum of 150 mm³
JM-402 Outsole Midsole revolutions of the
DIN 53516 Abrasion Test XC4 Rubber Outsole
Abrasion Test Outsole & Midsole Abrasion 10 x 10 Cm cilinder drum
SATRA WTM 174 40 RPM Maximum of 100 mm³
distance of 40 meters EVA Mid & Outsole
Maximum of 150 mm³
❸❹❺❼ Test Parameter Test Method Units Temperature Reporting Results Details
Tested through 84
Heel Top Lift revolution of the
JM-403 Attached Masonite or Leather Heels Top DIN 53516 Abrasion Test Full Heel Top
Abrasion Test cilinder drum Maximum of 90 mm³
Lift SATRA WTM 174 Lift 40 RPM
distance of 40 meters
❸❹❺❼ Test Parameter Test Method Material Cycles Reporting Results Details
Tested through 84
Leather Outsole DIN 53516 Abrasion Test revolutions of the
JM-413
Abrasion Test Leather Outsole Abrasion SATRA WTM 174 10 x 10 Cm cilinder drum
40 RPM Maximum of 200 mm³
distance of 40 meters
52.38 mm 34.93 mm
❸❹❺❼ Test Parameter Test Method Units Temperature Reporting Results Details 14.28 mm
JM-404 Material Strength A mechanical test designed to evaluate ASTM D3574 On the Instrom
2.5 Kg per Cm
6.4 mm
23 ±2 C° 25.4 mm
Split Tear Test the tear resistant properties of a foam. SATRA TM65 12 mm Slabs with 25
mm thickness 139.7 mm
❸❹❺❻ Test Parameter Test Method Units Cycles Reporting Results Details
Ross Flex tests how vulnerable the
Outsole Ross Flex ASTM D1052 Percentage 23 ± 2C° / 100.000 50%
JM-408 outsole material is to fatigue cracking
Test Growth
due to the repeated flexing induced when
SATRA TM60 % - 15 C° / 100.000 100%
walking
❸❹❺❻ Test Parameter Test Method Units Cycles Reporting Results Details
Ross Flex tests how vulnerable the
Midsole Ross Flex ASTM D1052 Percentage
JM-409 midsole material is to fatigue cracking
Test Growth 23 ± 2C° / 100.000 50%
due to the repeated flexing induced when
SATRA TM60 %
walking
❸❹❺❼ Test Parameter Test Method Units Cycles Reporting Results Details
❸❹❼ Test Parameter Test Method Material Cycles Reporting Results Details
EVA EVA Slabs.
❸❹❼ Test Parameter Test Method Material Cycles Reporting Results Details
EVA EVA Slabs.
Resilience Up to 380 X 380 mm.
JM-415 Rebound Resilience Elasticity Test for
Test DIN 53512 7 days after 23 ±2 C° ≤ 60 %
EVA Midsoles and Outsole production.
❸❹❺❼ Test Parameter Test Method Sample Construction Type Reporting Results Details
Outsole Non- Test specimen cut The flooring material is examined and any
JM-420 from the wearing Rubber or TPR Outsole (applied marking produced by the impact is
Marking Test No OutSole Marking after cleaning SATRA TM 223
surface of a to dark color only) assessed, together with the ease with
complete unit sole which any marking is removed.
Test frequency :
❶ Production - Daily
❷ Production - Twice a Day
❸ Development Phase
❹ Commercialization Phase by Fit Approval
❺ Initial Production by First Case
❻ Every New SKU in Production
❼ Every New Materials Batch
❽ Every PO