Professional Documents
Culture Documents
HX_AP-7_ETA-17-0813
HX_AP-7_ETA-17-0813
®
Designated according
to Article 29 of
Regulation (EU) No 305/2011
INSTYTUT TECHNIKI BUDOWLANEJ and member of EOTA
www.eota.eu
PL 00-611 WARSZAWA (European Organisation for
ul. Filtrowa 1
Technical Assessment)
tel.: (+48 22) 825-04-71
(+48 22) 825-76-55
fax: (+48 22) 825-52-86
www.itb.pl
General Part
Technical Assessment Body issuing the Instytut Techniki Budowlanej
European Technical Assessment
Product family to which the construction Torque controlled expansion anchor of sizes
product belongs M6, M8, M10, M12 and M16 for use in
non-cracked concrete
This European Technical Assessment is issued by the Technical Assessment Body in its
official language. Translations of this European Technical Assessment in other languages
shall fully correspond to the original issued document and should be identified as such.
Communication of this European Technical Assessment, including transmission by electronic
means, shall be in full. However, partial reproduction may be made, with the written consent
of the issuing Technical Assessment Body. Any partial reproduction has to be identified as
such.
Page 3 of European Technical Assessment ETA-17/0813, issued on 14/09/2017
Specific Part
3 Performance of the product and references to the methods used for its
assessment
3.1 Performance of the product
Min. 55 65 75 95 120
Total Length L [mm]
Max. 200 210 230 250 250
Min. 1 1 1 1 1
Thickness of the fixture tfix [mm]
Max. 145 145 155 155 130
Length Expansion Sleeve Ls [mm] 11,5 14,5 18 22 24
Thread Diameter dth 6 8 10 12 16
Width Torque Wrench SW [mm] 10 13 17 19 24
Base material:
Reinforced or unreinforced normal weight concrete of strength class C20/25 at minimum to
C50/60 at maximum according to EN 206.
Non cracked concrete: sizes from M6 to M16.
Design:
Anchorages are designed under the responsibility of an engineer experienced in anchorages
and concrete work.
Verifiable calculation notes and drawings are prepared taking account of the loads to be
transmitted. The position of the anchor is indicated on the design drawings (e.g. position of the
anchor relative to reinforcement or to supports, etc.).
Anchorages under static and quasi-static loads are designed in accordance with EOTA
Technical Report TR 055 (ETAG 001 Annex C, CEN/TS 1992-4-4:2009 and prEN 1992-4:2016).
Installation:
Anchor installation carried out by appropriately qualified personnel and under the supervision of
the person responsible for technical matters of the site.
Use of the anchor only as supplied by the manufacturer without exchanging any component of
the anchor.
Anchor installation in accordance with the manufacturer's specifications and drawings and using
the appropriate tools.
Check of concrete being well compacted, e.g. without significant voids.
Positioning of the drill holes without damaging the reinforcement.
In case of aborted hole: new drilling at a minimum distance away of twice the depth of the
aborted hole or smaller distance if the aborted drill hole is filled with high strength mortar and if
under shear or oblique tension load it is not in the direction of load application.
Cleaning of the hole of drilling dust.
Anchor installation such that the effective anchorage depth is complied with.
Application of the torque moment given in Annex B2 using a calibrated torque wrench.
Step 1
Step 2
Step 3
Step 4
Table C1: Performance under tension loads in non-cracked concrete (static and quasi static loading)
Anchor ANCLAJE AP-7
Steel failure
γMs
1)
Partial safety factor [-] 1,50 1,50 1,50 1,50 1,50
Pullout failure
γ2 = γinst
2) 3)4)
Installation safety factor [-] 1,0 1,0 1,0 1,2 1,2
Increasing factor concrete C40/50 ψc [-] 1,15 1,15 1,15 1,15 1,15
Factor for non-cracked concrete kucr,N 4) [-] 11,0 11,0 11,0 11,0 11,0
γ2 = γinst
2) 3)4)
Installation safety factor [-] 1,0 1,0 1,0 1,2 1,2
Increasing factor concrete C40/50 ψc [-] 1,15 1,15 1,15 1,15 1,15
Characteristic concrete cone failure scr,N [mm] 120 135 155 200 240
spacing splitting failure scr,sp [mm] 200 225 306 330 480
Short term tension displacement δN0 [mm] 0,4 0,5 0,7 0,4 0,6
Long term tension displacement δN∞ [mm] 0,9 0,9 0,9 0,9 0,9
1)
In the absence of other national regulations
2)
Parameter for design acc. ETAG 001 Annex C
3)
Parameter for design acc. CEN/TS 1992-4-4:2009
4)
Parameter for design acc. prEN 1992-4:2016
Table C2: Performance under shear loads in non-cracked concrete (static and quasi static loading)
Anchor ANCLAJE AP-7
γMs
1)
Partial safety factor [-] 1,25 1,25 1,25 1,25 1,25
Characteristic bending resistance M0Rk,s [Nm] 6,1 15,0 29,9 52,4 133,2
γMs
1)
Partial safety factor [-] 1,25 1,25 1,25 1,25 1,25
γMc
1)
Partial safety factor [-] 1,5 1,5 1,5 1,5 1,5
γMc
1)
Partial safety factor [-] 1,5 1,5 1,5 1,5 1,5
Minimum member thickness hmin [mm] 100 100 105 135 160
Short term tension displacement δV0 [mm] 0,8 1,8 1,8 2,0 2,0
Long term tension displacement δV∞ [mm] 1,2 2,7 2,7 3,0 3,0
1)
In the absence of other national regulations
2)
Parameter for design acc. ETAG 001 Annex C
3)
Parameter for design acc. CEN/TS 1992-4-4:2009
4)
Parameter for design acc. prEN 1992-4:2016