Professional Documents
Culture Documents
Zodiac Aerospace SB MXH-35-240 R7
Zodiac Aerospace SB MXH-35-240 R7
ZODIAC SERVICES
Technical Publication Department
7, avenue du PARANA
BP 303
91958 COURTABOEUF CEDEX
FRANCE.
Phone international : + 33 1 64 86 69 59
Fax international : + 33 1 64 86 69 84
TPI Web site: http://www.in-services.fr/technical/tpi
TRANSMITTAL SHEET
This Transmittal Sheet applies to the Revision 07, dated 20110901, of Service Bulletin MXH-35-240
REVISION SEQUENCE
A. Effectivity
This Service Bulletin applies to the inflatable harness PNR MXH Series manufactured
between 50th week of 2008 year (0850S) and 31th week of 2010 year (1031S) for the
PNR and batches listed in Appendix I.
These inflatable harness assemblies have been used for the manufacturing of new
masks (See Appendix II), and have been sold as spare parts from 15-dec-2008 to 31-
dec-2010, for the maintenance of masks already in service.
Inflatable harness PNR MXH Series manufactured before 33rd week of 2008 year
(0833S) are not marked with any batch number and are not concerned.
Inflatable harness PNR MXH Series manufactured between 33rd week of 2008 year
(0833S) and 49th week of 2008 year (0849S) are marked with a batch number and are
not concerned.
Full Face Quick Donning Mask Regulator (MF10 Series, MF20 Series), Crew Oxygen
Mask Regulator (MA10 Series, MC10 Series, MC20 Series, MRA Series) and Oxygen
Mask Regulator / With Detachable goggles (MLD20 Series) equipped with potentially
defective inflatable harness.
This Service Bulletin does not apply to the following Oxygen Mask regulators
B. Concurrent Requirements
Affected customers should notify their usual Zodiac Services contacts in regards of their
location
(ZS Europe, ZS UK, ZS Middle East, ZS Asia and ZS Americas).
Customers to provide the list of PNR and SER affected and place the corresponding orders
for replacement.
Removed harnesses must be sent in one batch at the end of the retrofit to the ZS work shop
from which your area corresponds to.
C. Reason
This Service Bulletin is issued :
- To inform the operators of the potential risk of rupture on the inflatable harness.
- To provide instructions for inspection and preventive replacement if necessary of
potentially defective inflatable harness.
D. Description
Based on our internal review and customer feedback, INTERTECHNIQUE has identified the
potentially defective batches of silicon tubes.
Inflatable harnesses assembled with defective silicon tubes have demonstrated an unusually
high premature rupture rate.
E. Compliance
F. Approval
G. Manpower
(1) 1 technician
None
Not Changed
Not applicable
K. References
L. Publications Affected
M. Interchangeability
Not affected
2. MATERIAL INFORMATION
A. Material – Price and Availability
(1) Material
UNIT PRICE
PNR KEYWORD QTY
(USD)
*Inflatable harness MXH15-2, MXH16, MXH30, MXH30G, MXH33 and MXH74G are obsolete due
to following Service Bullletins:
PNR Service Bulletin
MF20-501 MF20-534 MF20-542 MF20-35-22
MF20-107 MF20-35-24
MF20-003 MF20-501 MF20-503 MF20-524 MF20-534 MF20-35-25
MF20-506 MF20-35-26
MF20 Series MF20-35-32
MC10-15-109, MC10-15-120, MC10-16-100 and MC10-16-101
MC/F10-35-140
MF10-04-07
MC10-13-03, MC10-15-101, MC10-15-107, MC10-15-116, MC10-
MC10/MF10-35-141
35-101
Start End
Action to be performed on Aircraft
No
Replace the
Letter " I " marked on
inflatable harness
the bushing of Yes
inflatable harness of Batch number
the Crew Oxygen included in the list
Mask of appendix I Yes
(1) Removal of the inflatable harness from the Crew Oxygen Mask Regulator:
(a) Applicable to MA10, MC10, MC20, MF10, MF20 and MLC/MLD20 Series
2 Lift the locking tab of the coupling block which is in front of the regulator by
1 to 2 mm (0.04 to 0.08 in).
3 Hold the locking tab up and move the coupling block apart from the
regulator.
(2) Installation of the inflatable harness to the Crew Oxygen Mask Regulator:
(a) Applicable to MA10, MC10, MC20, MF10, MF20 and MLC/MLD20 Series
1 Install the harness on the regulator body and attach it with the screw.
2 Torque the harness attachment screw 0,20 N.m ± 0,02 (1.77 lb.in ± 0.17).
1 Connect the Crew Oxygen Mask Regulator to the oxygen supply source.
a Make sure that the harness is fully inflated in one second maximum.
(b) Apply a drop of leak test solution (SHERLOCK Type 1 or equivalent as per
MIL-PRF25567) to the inflatable harness.
1 Make sure that there is no leak between the regulator and the inflatable
harness.
(c) Make the test of mask regulator inner leakeage (Applicable to MRA005).
C. Re-identification
- The Crew Oxygen Mask Regulators MC10 Series are identified with the amendment letter
S,
- The Full Face Quick Donning Mask Regulators MF10 Series are identified with the
amendment letter T,
- The Full Face Quick Donning Mask Regulators MF20 Series (Except MF20-107) are
identified with the amendment letter M,
- The Crew Oxygen Mask Regulators MA10 SERIES are identified with the amendment letter Q,
- The Full Face Quick Donning Mask Regulators MF20-107 is identified by the new
PNR MF20-108,
(1) With indelible ink, write the relevant amendment letter or the new PNR on the
identification label.
D. Declaration of Modification
The form attached in appendix IV is to be filled by the customer and attach to the PO.
Batch Number
eg. : 0846Z10
Manufacturing Date
Year Week
eg.: 0912 = 12th week of 2009
Manufacturing Date
Year Week
Batch Number
eg.: 1012 = 12th week of 2010
eg. : 0942Z1
APPENDIX I
PNR Batches
0849Z12 / 0850Z12 / 0851Z14 / 0852Z14 / 0901Z14 (or 091Z14) / 0902Z14 (or 092Z14) 0902Z15 (or 092Z15)
MXHA200
0903Z15 (or 093Z15) / 0904Z15 (or 094Z15) / 0905Z15 (or 095Z15) / 0906Z15 (or 096Z15) / 0939Z2
0845Z10 / 0846Z10 / 0847Z10 / 0847Z11 / 0849Z12 / 0901Z14 (or 091Z14) / 0902Z14 (or 092Z14) / 0902Z15
MXH15-2
(or 092Z15) / 0903Z15 (or 093Z15) / 0904Z15 (or 094Z15) 0905Z15 (or 095Z15) / 0919Z15 / 0920Z15 / 0939Z2
0846Z10 / 0847Z10 / 0849Z12 / 0901Z14 (or 091Z14) / 0902Z14 (or 092Z14) / 0903Z15
MXH15-22
(or 093Z15) / 0904Z15 (or 094Z15) / 0905Z15 (or 095Z15) / 0915Z15 / 0919Z15 / 0920Z15 / 0939Z2
0841Z14 / 0849Z13 / 0850Z14 / 0851Z14 / 0852Z14 / 0902Z14 (or 092Z14) / 0902Z15 (or 092Z15) / 0903Z15
MXH16
(or 093Z15) / 0904Z15 (or 094Z15) / 0905Z15 (or 095Z15) 0906Z15 (or 096Z15) / 0939Z2
0850Z9-1 / 0850Z9-2 / 0850Z9-6 / 0901Z9-15 (or 091Z9-15) / 0901Z9-20 (or 091Z9-20) 0902Z10-1 (or 092Z10-1)
MXH64G
0902Z10-2 (or 092Z10-2)
MXH67G 0901Z9-15 (or 091Z9-15) / 0901Z9-20 (or 091Z9-20) / 0902Z10-2 (or 092Z10-2)
PNR Batches
0849Z7-16 / 849Z8-2 / 0850Z8-2 / 0850Z8-3 / 0850Z9-4 / 0850Z9-6 / 0851Z9-6 / 0851Z9-7 0851Z9-8 / 0852Z9-13
MXH74G
0852Z9-14 / 0852Z-9-14
0849Z8-1 / 0849Z8-2 / 0850Z8-3 / 0850Z9-1 / 0850Z9-2 / 0850Z9-3 / 0850Z9-4 / 0850Z9-5 0850Z9-6 / 0851Z9-8
0851Z9-9 / 0851Z9-10 / 0851Z9-11 / 0852Z9-11 / 0852Z9-12 0852Z9-13 / 0901Z9-15 (or 091Z9-15) / 0901Z9-16
(or 091Z9-16) / 0901Z9-17 (or 091Z9-17) / 0902Z9-20 (or 092Z9-20) / 0902Z10-1 (or 092Z10-1) / 0902Z9-18
MXH74-20G (or 092Z9-18) / 0902Z9-19 (or 092Z9-19) / 0911Z12-5 / 0915Z13-1 / 0916Z13-2 0916Z13-3 / 0916Z13-4
0916Z13-5 / 0917Z13-6 / 0917Z13-7 / 0917Z13-8 / 0917Z13-9 / 0919Z13-1 / 0919Z13-12 / 0920Z13-13
0921Z13-12 / 0921Z13-13 / 0921Z13-14 / 0924Z1-15 / 0924Z1-16 / 0924Z1-17 / 0924Z1-18 / 0939Z2-8
0940Z1-9 / 0940Z1-10
APPENDIX II
Crew Oxygen Mask manufactured with a potential defective inflatable harness
APPENDIX III
CMM N° EQUIPMENT PNR DESIGNATION
35-10-20 MA10 Series CREW OXYGEN MASK REGULATOR
35-13-60 MF20 Series FULL FACE QUICK DONNING MASK REGULATOR
35-13-61 MF10 Series FULL FACE QUICK DONNING MASK REGULATOR
35-13-62 MC20 Series CREW OXYGEN MASK REGULATOR
35-13-63 MC10 Series CREW OXYGEN MASK REGULATOR
35-13-64 MLD20 / MLC20 Series OXYGEN MASK REGULATOR / WITH DETACHABLE GOGGLES
35-17-10 MRA005 CREW OXYGEN MASK REGULATOR
APPENDIX IV
DECLARATION OF MODIFICATION
EQUIPMENT(S) MODIFIED:
Mask Harness
Modification Date:
Name, position, signature of the modification responsible: