Professional Documents
Culture Documents
lab-10_13_14_15
lab-10_13_14_15
lab-10_13_14_15
Title: To configure and understand about static routing using cisco packet tracer.
Static Routing
Static routing is a type of network routing technique. Static routing is not a routing protocol;
instead, it is the manual configuration and selection of a network route, usually managed by
the network administrator. It is employed in scenarios where the network parameters and
environment are expected to remain constant. Static routing performs routing decisions with
preconfigured routes in the routing table, which can be changed manually only by
administrators. Static routes are normally implemented in those situations where the choices in
route selection are limited, or there is only a single default route available. Also, static routing
can be used if you have only few devices for route configuration and there is no need for route
change in the future. Static routing is considered the simplest form of routing.
Samana Shrestha
Roll no.: 26
Gig0/0/0 192.168.2.1 255.255.255.0 N/A
Router 2
Gig0/0/1 192.168.3.2 255.255.255.0 N/A
Samana Shrestha
Roll no.: 26
Figure: Command Line Interface of Router 0
Samana Shrestha
Roll no.: 26
Figure: Command Line Interface of Router 1
Samana Shrestha
Roll no.: 26
Message Transmission
After the complete setup of static routig the PC0 is able to communicate with PC1.
Conclusion:
The static routing was configured successfully using cisco packet tracer.
Samana Shrestha
Roll no.: 26
Lab Program Number: 14 Date: 2080/10/19
Title: To setup OSPF in cisco packet tracer.
Procedure
Step 1. Open the CISCO Packet tracer software
Step 2. Drag and drop 2 pcs using End Device Icons on the left corner
Step 3. Drag and drop 3 routers and 2 switch from networking devices.
Step 4. Make the connections using copper straight through and copper cross-over cable.
Step 5. Configure the IP address of the PCs by clicking on the “Desktop” tab, then select “IP
configuration”, Write the IP address of the network and click at the Subnet mask filed.
Subnet Mask will appear automatically and for router use the CLI command.
Step 6. Configure OSPF in all the routers using CLI command.
Addressing Table
Device Interface IPv4 Address Subnet Mask Default Getaway
Samana Shrestha
Roll no.: 26
Fa0/0 155.165.1.1 255.255.0.0 N/A
Router 2
Se2/0 30.0.0.2 255.0.0.0 N/A
Samana Shrestha
Roll no.: 26
Figure: Command Line Interface of Router 1
Samana Shrestha
Roll no.: 26
Figure: Command Line Interface of Router 2
Samana Shrestha
Roll no.: 26
Figure: Command Line Interface of Router 3
Samana Shrestha
Roll no.: 26
Message Transmission
Step 6.
After the complete setup of OSPF the PC0 is able to communicate with PC1.
Conclusion:
The OSPF was configured successfully using cisco packet tracer.
Samana Shrestha
Roll no.: 26
Lab Program Number: 13 Date: 2080/10/15
Title: To setup web DNS server in cisco packet tracer.
Web Server
A web server is software and hardware that uses HTTP (Hypertext Transfer Protocol) and other
protocols to respond to client requests made over the World Wide Web. The main job of a web
server is to display website content through storing, processing and delivering webpages to
users.
DNS server
The Domain Name System (DNS) is the phonebook of the Internet. When users type domain
names such as ‘google.com’ or ‘nytimes.com’ into web browsers, DNS is responsible for
finding the correct IP address for those sites. Browsers then use those addresses to
communicate with origin servers or CDN edge servers to access website information.
Procedure
Step 1. Open the CISCO Packet tracer software
Step 2. Drag and drop 1 pc and 2 server using End Device and 1 switch from networking
devices on the left corner
Step 3. Make the connections using copper straight through.
Step 4. Configure the IP address of the PC and servers by clicking on the “Desktop” tab, then
select “IP configuration”, fill the fields as per the addressing table
Step 5. Configure the HTTP server by clicking on the web server and then on “Services” then
on HTTP. Edit the index.html file as desired.
Step 6. Configure the DNS server by clicking on DNS server (device) and then go to services
then click on DNS. Then turn on the DNS services. Name the server in this case
“www.lab13.com” and type address in this case “192.168.1.1” and add the record.
Step 7. Verify the server by using the web browser in the Host by clicking on the “Desktop”
tab, then select “Web Browser” and fill the URL in this case “www.lab13.com” . It will
show the results.
Samana Shrestha
Roll no.: 26
Addressing Table
Device IPv4 Address Subnet Mask Default Getaway DNS Server
Samana Shrestha
Roll no.: 26
Figure: Simulation Panel
Samana Shrestha
Roll no.: 26
Figure: html page
Conclusion:
The web DNS server was configured successfully using cisco packet tracer.
Samana Shrestha
Roll no.: 26
Lab Program Number: 10 Date: 2080/09/28
Title: To setup RIP in cisco packet tracer.
Procedure
Step 1. Open the CISCO Packet tracer software
Step 2. Drag and drop 2 pcs using End Device Icons on the left corner
Step 3. Drag and drop 2 routers and 2 switch from networking devices.
Step 4. Make the connections using copper straight through and copper cross-over cable.
Step 5. Configure the IP address of the PCs by clicking on the “Desktop” tab, then select “IP
configuration”, Write the IP address of the network and click at the Subnet mask filed.
Subnet Mask will appear automatically and for router use the CLI command.
Step 6. Configure RIP in all the routers using CLI command.
Addressing Table
Device Interface IPv4 Address Subnet Mask Default Getaway
Samana Shrestha
Roll no.: 26
Figure: RIP configuration
Samana Shrestha
Roll no.: 26
Figure: Command Line Interface of Router 1
Message Transmission
Samana Shrestha
Roll no.: 26
Step 6.
Samana Shrestha
Roll no.: 26
Figure: PC0 pinging PC1
Conclusion:
The RIP was configured successfully using cisco packet tracer.
Samana Shrestha
Roll no.: 26