Professional Documents
Culture Documents
طريقة التنفيذ اخر حاجه
طريقة التنفيذ اخر حاجه
ﺧدﻣﺎت
اﻟﺻرف اﻟﺻﺣﻲ اﻟﻣﺳﺗداﻣﺔ
اﻟﻣﻧﺎطق اﻟرﯾﻔﯾﺔ
1
مالحظات تاريخ االصدار رقم االصدار
االهتمام بطريقة التنفيذ و مراعاة 22/5/2022 األول
أصول الجودة و السالمة و المعدات و
المرجعيات
عدم ارتباط الخطة بطبيعة العمل 18/11/2022 الثاني
بالمشروع
وجود ملفات خاصة بخطط اخري 18/1/2023 الثالث
بدون التوضيح
تم إضافة اختبار تسريب المطابق و 7/6/2023 الرابع
االعمال الكهروميكانيكية
22/1/2024 الخامس
التوضيح الرمز
أبو جريدة AB
طريقة التنفيذ MS
2
3
محتويات طريقة التنفيذ
الصفحة العنوان م
4
معلومات عن المشروع:
اسم المشروع :تنفيذ شبكات االنحدار ومحطات الرفع وخطوط طرد الصرف
الصحي لقرية أبو جريدة و الطحان -تجمع قروي الرحامنه – مركز
فارسكور – محافظة دمياط
5
أعمال خط الطرد
مرحلة ما قبل التنفيذ :
استخراج التصاريح الالزمة. .1
التخطيط (التأكد من توافر الموارد البشرية الالزمة للعمل والمعدات والمواد الالزمة لألعمال). .2
التأكد من تطبيق اشتراطات السالمة والصحة المهنية والبيئة قبل البدء ألي من انشطة المشروع وإصدار تصريح .3
الحفر.
تواجد اللوحات التنفيذية المعتمدة من االستشاري. .4
أعمال خط الطرد:
-الموارد البشرية:
-يلزم للتنفيذ جزء من خط طرد فرقة من العمالة الجاهزة للتنفيذ االعمال وتتكون هذه الفرقة من العماله
والمساعدين والسائقين للمعدات تحت اشراف ( مهندس التنفيذ -مساح-المشرف)
-المهام الوظيفية لكل مورد بشري مما سبق:
-1مهندس التنفيذ كما هو مذكور بخطة الجودة .
-2المساح كما هو مذكور بخطة الجودة.
-3المشرف :تنفيذ تعليمات مهندس التنفيذ ومتابعة العمال وتنسيق وترتيب وتوزيع المهام على العمال
ومتابعة اداء المعدات
-4رئيس العمال :متابعه تنفيذ العمال للمهام واستخدام االدوات المناسبة فى انجاز العمل
-5عمال سباكة العمال تركيبات المواسير
-6عمال حفر لحفر الخنادق وسند جوانب الحفر
-7مساعدين للصنايعية لمناولة العدد واستخدام االدوات مثل الدكاك ...الخ
6
يتم استخدام العديد من المواد الالزمة اإلنجاز العمل (مواسير UPVC 10بار او حسب نوع المواسير -
المعتمدة طبقا للمواصفات وكراسه المقايسة -جوانات 10بار – شحم نباتي – رمل – االكواع لزوم
تغير اتجاه المسار – خرسانه لزوم المصدات خلف االكواع – مياه لزوم االختبار)
المعدات واألدوات: -
يتم استخدام للفرقة الواحدة (حفار +لودر +خيط +جرار +دكاك ميكانيكي او مندله يدوية +ميزان -
قامة +متر +أدوات االختبار من طبب واجهزه القياس +ماكينة اللحام في حاله مواسير بولي ايثيلين)
اختبارات الجودة: -
داخل الموقع :يتم عمل اختبارات الدمك الالزمة على الرمل وطبقات الردم عن طريق استخدام -
المخروط الرملي (( sand coneلتحديد الكثافة الجافة بطبقات الردم و الرمال و التي ال تقل نسبة
الكثافة لطبقات الردم المختلفة عن + %95اختبارات الضغط على 15بار.
خارج الموقع :اختبارات على المواسير الموردة وقطع الزهر الخاصة بالموقع في مركز بحثي معتمد -
+اختبارات على خرسانه مصدات االكواع.
إجراءات االمن والسالمة: -
يتم االلتزام اثناء تنفيذ العمل بتطبيق اجرأت االمن والسالمة: -
(وجود تصاريح حفر +الشدة الخشبية سواء كانت مفتوحة او مغلقة طبقا لتقرير سند جوانب الحفر +
ضرورة التنبيه على وجود شنطة اإلسعافات األولية داخل الموقع +ضرورة وجود ارقام الطوارئ
داخل الموقع +العزل الجيد لمنطقه االعمال +استخدام لوحات كهربية معتمدة لتوصيل الكهرباء
للمعدات).
خطوات التنفيذ للبند:
يكون تنفيذ المواسير في خطوط مستقيمة ولذلك بعمل أوتار على جانبي الحفر وكذلك شد خيطان على جنب واعلى
الماس ورة اثن اء التنفي ذ و يجب عم ل التخطي ط بك ل دق ة قب ل ب دء العم ل والمق اول مس ئول عن ذل ك مس ئولية تام ة
ومباشرة.
7
يجب أن يتم الحفر على المناسيب المبينة بالرسومات باإلضافة إلى عمل طبقة األساس والمحافظة على الميول ،كما
يجب أن يك ون ع رض الحف ر للخن دق واس عا بدرج ة كافي ة بحيث يعطى م ا ال يق ل عن 30س م من ك ل ج انب من
جوانب الماسورة أي يجب أن يكون عرض الخندق أكبر من القطر الخارجي للماسورة بما ال يقل عن 60سم ،كما
يجب عمل حفرة مناسبة وكافية لرأس الماسورة في األماكن المتوقعة لزوم أعمال التركيب.
يجب أن يكون األساس للمواسير من التربة الرملية سمكها ال يقل عن 30سم فإذا صادف ذلك طبقة صلبة فيجب
إزال ة ه ذه الطبق ة واس تبدالها بطبق ة األس اس بنفس الس مك ،ويجب على المق اول اعتم اد عين ة طبق ة األس اس قب ل
التوريد.
يجب أن يتم ال ردم بالرم ل النظيف حتى 30س م أعلى من ظه ر الماس ورة ويجب تجنب س قوط كت ل أو ص خور أو
أحجار ويتم الردم بأتربة نظيفة خالية من المواد الصلبة على طبقات سمك كل منها ال يزيد عن 25سم مع رشها
بالمياه ودكها دكا جيدًا.
يجب وض ع طبق ة األس اس وض غطها إلى أقص ى كثاف ة نس بة ال تق ل عن % 95م ع خلوه ا تمام ا من األحج ار
والنتوءات الصلبة حتى تصبح التربة متجانسة ومنتظمة ومطابقة للمناسيب التي تتماشى مع تركيب المواسير.
يجب على المق اول قب ل القي ام ب الحفر القي ام بتنظي ف الموق ع واألرض ض من ح دود المش روع من كاف ة المخلف ات
والحشائش وجذور األشجار إذا وجدت أو أي أساسات قديمة وتسوية الموقع طبقا للمناسيب الواردة بالرسومات.
أعمال الحفر ونزح المياه ألساسات المواس ير يجب أن تتم طبقا للمناسيب الموض حة بالرسومات لذلك يجب أن يتم
تس نيد ج وانب الحف ر س واء باألخش اب أو الس تائر المعدني ة إذا ل زم األم ر ويجب اعتم اد ن وع طريق ة تس نيد ج وانب
الحفر وطريقة ونوع نزح المياه من مهندسي االشراف قبل البدء في العمل.
يجب أخ ذ موافق ة المهن دس المش رف على ع رض تكس ير األس فلت من الش وارع والط رق الحالي ة على أن يتم اتخ اذ
كافة التدابير واإلجراءات الالزمة نحو القيام بإعادة الرصف مرة أخرى والمقاول مسئول وحده عن أي زيادة في
تكسير عرض أكبر من المطلوب وسوف ال يدفع له أي تكاليف إضافية نظير ذلك.
8
تغطى المواسير بطبقة من الرمل الناعم مع الرش والدك للوصول إلى كثافة نسبية ال تقل عن .%95
يستكمل الردم حتى منسوب أسفل أساس الطريق بناتج الحفر الصالح للردم بشرط أال يحتوي على أحجار أو
مخلفات مباني أو مواد عضوية او رمال نظيفة مورده من الخارج حسب تعليمات جهة التصريح ويرش بالمياه
وتترك جيدا حتى يعطى كثافة نسبية ال تقل عن .%80
9
المعدات واألدوات: -
يتم استخدام للفرقة الواحدة (حفار +لودر +جرار +ميزان قامة +متر +أدوات النجارة +أدوات -
الحدادة +أدوات تجميع القطع الزهر المرن)
اختبارات الجودة: -
داخل الموقع :يتم عمل اختبارات الضغط للقطع الخاصة +اختبارات موقعيه على الخرسانة SLUMP -
+ TESTقياس درجه حرارة الخرسانة.
خارج الموقع :اختبارات على قطع الزهر الخاصة في مركز بحثي معتمد +اختبارات مقاومه على -
خرسانه الغرفة +اختبارات على االغطية .GRP
إجراءات االمن والسالمة: -
يتم االلتزام اثناء تنفيذ العمل بتطبيق اجرأت االمن والسالمة: -
(وجود تصاريح حفر +الشدة الخشبية سواء كانت مفتوحة او مغلقة طبقا لتقرير سند جوانب الحفر +
ضرورة التنبيه على وجود شنطة اإلسعافات األولية داخل الموقع +ضرورة وجود ارقام الطوارئ
داخل الموقع +العزل الجيد لمنطقه االعمال +استخدام لوحات كهربية معتمدة لتوصيل الكهرباء
للمعدات +الخ .)....
خطوات تنفيذ البند:
-1استخراج تصريح من الجهة المانحة للتصريح حسب مكان الغرفة
-2التخطيط لمكان الغرفة.
- 3الحفر مع سند الجوانب طبقا لعمق الغرفة وتعليمات تقرير سند جوانب التربة وتعليمات االستشاري
-4شد نجاره الخرسانة العادية +الصب للخرسانة العادية.
-5معالجة الخرسانة العادية جيدا.
- 6شد نجاره اللبشة المسلحة للغرفة +تشكيل وتركيب حداده اللبشة +تركيب الواتر استوب مانع
التسريب مع اللحام الجيد لمنطقه الركوب وعمل الكيكر +صب اللبشة المسلحة.
-7شد نجاره الحوائط سواء من الداخل او من الخارج حسب التنسيق مع االستشاري +تشكيل وتركيب
الحدادة للحوائط وتركيب البسكوت لزوم الغطاء الخرساني +شد الوجهة المتبقي من النجارة والتقوية
الجيدة +الصب للحوائط على اال يزيد ارتفاع الصب عن 2.7م وفى حاله غرف العدايات العميقة يتم
الصب على حطات ال تتدعى 2.7م للحطة الواحدة.
- 8المعالجة الجيدة للخرسانة بعد الصب بالمياه او أي طريقه معالجه معتمده من استشاري االشراف
على التنفيذ.
10
-9معالجة أي تسويس او تعشيش باستخدام مونه غير قابله لالنكماش (جراوت +اديبوند) او ما
يماثلهما.
-10يتم العزل الخارجي للحوائط عن طريق البيتومين البارد 3أوجه يسلم كل منها على حدي.
-11يتم الردم حول الغرفة من الخارج والدمك الجيد لتربه الردم.
-12يتم شد نجاره السقف وتشكيل وتركيب حديد التسليح مع تخطيط أماكن األغطية سواء GRPاو
بالطات فك وتركيب طبقا للوحات المعتمدة.
-13يتم االنتهاء من التركيبات الميكانيكية (القطع الخاصة).
- 14يتم تشطيب الغرفة من الداخل على خطوات (المعالجة الماكن الزراجين والتقويات بمونه غير
قابله لالنكماش وكذلك الفواصل وكذلك أماكن الشنايش للمواسير – عمل خرسانه الميول – ودهان
العزل الداخلي حسب االعتماد ايبوكسى إسمنتي او ما يماثله).
11
المشرف :تنفيذ تعليمات مهندس التنفيذ ومتابعة العمال وتنسيق وترتيب وتوزيع المهام على العمال -
ومتابعة اداء المعدات
رئيس العمال :متابعه تنفيذ العمال للمهام واستخدام االدوات المناسبة فى انجاز العمل -
عمال سباكة العمال تركيبات المواسير -
عمال حفر لحفر الخنادق وسند جوانب الحفر. -
عمال لتركيب وتنظيف الفرم لزوم المطابق . -
مساعدين للصنايعية لمناولة العدد واستخدام االدوات مثل الدكاك ...الخ -
12
اختبار المثيلين كلوريد -7
اختبار المواسير بعد التركيب اختبار القمع وكذلك تكرار االختبار بعد الردم. -8
يجب على المقاول أن يقوم على نفقته بتجربة المطابق كلما طلب منه المهندس المشرف ذلك وتجرى التجربة بضغط -
الماء بعد سد فتحات المواسير الموجودة بالمطابق بالطبات وملئ المطبق بالماء إلى االرتفاع الذي يحدده المهندس
المشرف ومشاهدة تغيير منسوب الماء مدة 24ساعة.
خطوات التنفيذ:
التخطيــــــــط:
يجب عم ل التخطي ط بك ل دق ة قب ل ب دء العم ل والمق اول مس ئول وح ده عن دق ة ه ذا التخطي ط ،ويجب علي ه المحافظ ة -
على األوتار والثوابت والروبيرات وجميع األشياء األخرى المماثلة.
13
كما يجب عليه المحافظة على العالمات المساحية القائمة وعالمات الحدود والمسافات والمحاور ويتخذ ما يلزم لمنع -
إزالتها أو تغيير مواقعها ويكون مسئوال عما يترتب على اإلزالة أو التغيير من نتائج وعليه إعادتها ألصلها.
يتم عم ل الميزاني ات على أس اس الروب يرات الموج ودة بالمنطق ة والمعتم دة ل دى المهن دس وعلى المق اول مراجع ة -
مناسيب سطح األرض قبل البدء في التنفيذ فإذا وجد اختالف يرجى الرجوع للمكتب االستشاري.
يقر المقاول بأنه قد عاين موقع العمل وتأكد من طبيعة التربة وأنه قد كون فكرة واضحة تماما من الظروف المحيط ة -
بالموقع وطبيعة األرض وأنه قد حصل على أي معلومات أخرى الزمة ويعتبر أن المقاول قد تمكن من الوصول إلى
موقع العمل وأنه قد أخذ في االعتبار فتح أي طرق مؤقتة قد تكون الزمة لنقل المواد واآلالت.
الجسـات:
مســار الخطـــــوط:
-قبل البدء في األعمال يقوم المهندس المشرف من قبل المالك باعتماد الرسومات التنفيذية التي سيتقدم بها المقاول
والمبنية على الرسومات التصميمية المرفقة بالعطاء وبحيث تكون هذه الرسومات التنفيذية مبينا عليها الطرق والمسارات
التي ستركب عليها المواسير مع البيانات المتاحة عن األعمال األخرى بمواقع األعمال مثل الكابالت والمجاري
المقاول مسئول وحده عن تخطيط وتثبيت قضبان اللمحة بكل دقة وهو ملزم باستحضار األدوات والمهمات الالزمة لذلك
وعليه إخطار المهندس المشرف عندما يستلزم تقدم العمل تخطيط أي جزء أو تثبيت قضبان اللمحة بمدة ال تقل عن ثالثة
أيام.
14
تركيب الـمواسيــر:
يراعى اتجاه التركيب للمواسير واستخدام شحم نباتي او ما يماثله ويراعى مقدام اللبوس للمواسير وتركيب الوصالت
القصيرة المرنة.
االختبار:
يتم اختبار خط مواسير االنحدار عن طريق اختبار القمع لتأكد من عدم وجود أي تسريب من جسم المواسير او -
أماكن الوصالت ويتم اجراء االختبار طبقا للمواصفات والكود المصري.
يتم اجراء اختبار القمع مرتين مرة قبل الردم و مره بعد الردم. -
يتم الردم حول وفوق الماسورة بمسافه ال تقل عن 30سم برمال نظيفة مورده من الخارج ويتم الدك جيدا والغمر -
بالمياه للوصول لكثافه دمك ال تقل عن .% 95
15
يتم ردم باقي القطاع اما بناتج حفر او رمال نظيفة مورده من الخارج حسب تعليمات المواصفات الفنية او الجهات -
المانحة للتصاريح.
المطـــابق:
االسمنت المستخدم في الخرسانة الخاصة بالمطابق وألي جزء من أجزاءها من االسمنت المقاوم للكبريتات. -
يتم تنفيذ المطابق على مسافات معينة وطبقا للرسومات المرفقة على خطوط مواسير صرف مياه المجاري إلمكان -
صيانة هذه الخطوط.
تعمل األساسات واألرضية الخرسانية للمطابق من الخرسانة المصبوبة في الموقع أما الحوائط فيمكن أن يتم صبها -
في الموقع وذلك كما هو مبين بالرسومات.
الساللم:
يركب بحوائط المطابق من الداخل ساللم مصنوعة من الحديد الزهر الرمادي وال يقل وزن درجة السلم الواحدة عن -
7.25كجم وتكون الساللم على مسافات 35سم رأسيا وعلى مسافة 15سم أفقيا على األكثر ويجب اعتماد نماذج
الساللم من المهندس المشرف وتحديد اسم المصنع المنتج قبل التوريد والتركيب.
األغطية:
تعمل أغطية المطابق وإ طارات هذه األغطية من نوع البوليستر المسلح باألليـاف الزجاجية ( )G.R.Pويجب اعتماد
نموذج األغطية من المهندس المشرف و تحديد اسم المصنع المنتج لها قبل التوريد والتركيب ويركب إطار الغطاء فوق
المطابق بحيث يكون منسوب سطح الغط اء من أعلى في مستوى السطح النهائي لطبقة الرصف بالطريق أو حسب أي
منسوب يحدده المهندس المشرف ويكتب على أغطية المطابق باللغة العربية و بالخط البارز مشروع الصرف الصحي
للقرية ويجب التحبيش جيدا حول اإلطارات بخرسانة عادية نوع ( ج ) مع دهانها من الداخل والخارج بالبيتومين
غرف التفتيش:
يتم تنفيذ غرف التفتيش من الخرسانة العادية بأبعاد طبقًا لرسومات التفاصيل العامة. -
16
توريد وتركيب وتجربة واختبار غرف التفتيش والفئة تشمل األعمال األتية: -
الحفر في أي ن وع من أن واع الترب ة وإزال ه الم واد المختلف ة الزائ دة ال تي ال تل زم للردم في م دة ال تتج اوز 24س اعة من
وقت اس تخدامها من الحفر ونقل األترب ة مؤقتا للردم بها عند اللزوم إذا أمر بذلك كتاب ه وعمل الشدات الالزم ة لحماية
الحفر ونزح المياه.
الــــــردم:
تجرى عملية الردم حول المطابق برمال نظيفة مورده من الخارج طبقا للبند. -
17
-مساعدين للصنايعية لمناولة العدد واستخدام االدوات مثل الدكاك ...الخ
-المواد المستخدمة:
-يتم استخدام العديد من المواد الالزمة اإلنجاز العمل (محتويات الخرسانة (رمل +زلط +اسمنت مقاوم
للكبريتات +مياه خلط) +حديد تسليح +واتر ستوب +خسب لطزانه وموسكي وعروق & بالي وود+
بسكوت مناسب +زراجين مائية +خيطان ومسامير +مواد عزل داخلي +مواد عزل خارجي +درج
سلم
-المعدات واألدوات:
-يتم استخدام للفرقة الواحدة (حفار +لودر +جرار +ميزان قامة +توتال استيشن +متر +أدوات
النجارة +أدوات الحدادة)
-المعدات المستخدمة في الصب من هزازو مضخة خرسانة وعربيات خرسانة
-2يتم الحفر لمنسوب التأسيس طبقا لتقرير التربة المعتمد ووضع الخنزيرة في مركزها طبقا للوحات التنفيذية المعتمدة
ويمنع وضع الخنزيرة على سطح األرض حتى ال يحدث أي ميل مفاجأ اثناء الصب في البيارة وقبل التغويص.
- 3يتم شد الفانوس الداخلي (النجارة الداخلية) للبيارة سطح أملس طبقا للمواصفات الفنية للمشروع.
18
-5يتم ش د النج ارة الخارجي ة م ع التقوي ة الجي دة طبق ا ألص ول الص ناعة وتعليم ات جه از االش راف من االستش اري ويتم
صب 2.7م طبقا لتعليمات الكود المصري.
- 6المعالجة الجيدة للخرسانة بعد الصب بالمياه او أي طريقه معالجه معتمده من استشاري االشراف على
التنفيذ.
-7معالجة أي تسويس او تعشيش او أماكن الزراجين بعد التخويش وقطع الزراجين باستخدام مونه غير
قابله لالنكماش (جراوت +اديبوند) او ما يماثلهما.
-8يتم العزل الخارجي للحوائط عن طريق البيتومين البارد 3أوجه يسلم كل منها على حدي.
الحفر التغويص للبيارة:
- 1يتم عمل تدريج على جسم البيارة الخارجي ويتم تركيب شواغيل في أربع اتجاهات متعامدة على بعضها
البعض.
-2يتم التغويص عن طريق الكباش.
-3يتم رصد منسوب التغويص باألجهزة المساحية وعن طريق التدريج والشواغيل.
-4يتم ترحيل األتربة اول بأول.
-5منع نزح أي مياه من البيارة اثناء التغويص.
20
أعمال التشطيبات لمحطة الرفع:
21
ثانيا :أعمال بياض التخشين الداخلي:
22
ثالثا :أعمال بياض التخشين الداخلي:
المسئول عن
المعدات المطلوبة
مالحظات التنفيذ خطوات تنفيذ البند اسم البند م
ومواصفاتها
(مقاول – ذاتي)
التأكد من توافر الموارد البشرية والمعدات
تصريح العمل
والمواد الالزمة لألعمال
التأكد من تطبيق اشتراطات السالمة والصحة بروة محارة +مسطرين مونة
+قروانة المهنية والبيئة
نظافة االسطح المراد بياضها من االخشاب
ميزان مياه
وخالفه ورش االسطح بالمياه
مقاول باطن (مصنعيات)
قدد المونيوم أطوال -ميزان عمل الطرطشة (رمل +اسمنت) طبقا
خيط (ثقل) وخيط للمقايسة ورش الطرطشة بالمياه
طبقة البطانة (رمل +اسمنت) طبقا للمقايسة 3
تخشينه مع الدرع والتخشين أو على حسب نوعية
البياض المطلوب
23
24
رابعا -أعمال األرضيات
الموارد البشرية:
-1مهندس تنفيذ
-2مشرف تنفيذ
-3مهندس ضبط جودة
-4عمالة ماهرة
) -5عمال تركيب البالط (محاجر -الجرانيت -السيراميك -البورسلين -الرخام -الموزاييك
العدة المستخدمة- :
-1سكينة قطع البالط.
-2قدة
-3خيط
-4ميزان مياه
-5مسطرين
-6شاكوش من المطاط
-7قروانة
-8بلطة
المواد المستخدمة
-1أسمنت بورتالندی عادی
-2أسمنت أبيض
-3رمل
-4جير
-5شريحة من الحديد الذي ال يصدأ
-6بالط
تعليمات تشغيل أعمال األرضيات
-1التشوين:
-1.1يشـون البالط األسمنتي مقاس ( )۲ × ۲۰ × ۲۰سم وجهًا لوجه في رصات متساوية.
-1.2تكون الرصات رأسية على سدايب من خشب بغدادي بين كل رصه وأخرى.
-1.3يجب رش البالط رشًا غزيرًا بالمياه قبل استعماله مباشرة.
25
-2إعداد األسطح:
-2.1يجب أن تكون جميع األسطح مستوية خالية من الكتل الخرسانية.
-2.2يجب أن تكون جميع األسطح بها فرشة من الرمال الخالي من المواد الطينية.
-3المونة:
تتكون المونة من 300كجم من األسمنت البورتالندي العادي مضافة إلى واحد متر مكعب من الرمل مضافًا إليها كمية المياه
المناسبة.
26
يتم تحديد المناسيب المختلفة وعالقتها ببعضها مع أخذ لقطة من شرب من مدخل المبني. .1
يتم فرش مونة نصف جافة (مفلفلة) باستخدام ٢٥٠كجم أسمنت /م 3رمل بالسمك المطلوب وال تزيد عن 7سم. .2
يتم وضع لباني األسمنت قبل لصق الدرج سواء القائمة او النائمة. .3
يتم لصق الدرج طبقًا للشكل المعتمد مع ضبط أفقية الرخام وانف السلم باستخدام ميزان الماء طبقًا للمواصفات الفنية والرسومات .4
التنفيذية المعتمدة.
يتم تركيب التلبيسة للدرج بمونة األسمنت والرمل مع تجليخ أطراف التلبيسة جيدًا بالصاروخ ثم السقية وإتمام العمل طبقًا للمواصفات .5
الفنية وأصول الصناعة.
مرحلة التنفيذ:
توفير المعدات الالزمة لتنفيذ أعمال الزراعة طبقًا للمعدالت والتواريخ المحددة بالبرنامج الزمني المعتمد من استشاري المشروع. .1
27
يتم أعمال الحفر الالزم باستخدام البلدوزر حتى المنسوب المحدد بالرسومات التنفيذية المعتمدة. .2
توريد النجيلة من مشاتل معتمدة. .3
توريد وتنفيذ أعمال تنسيق الموقع طبقًا لرسومات الورشة التنفيذية. .4
أعمال التجهيزات
يتم البدء في أعمال العزل بعد تصلد األسطح الخرسانية وكذلك المونة األسمنتية لقصية الردم. .1
يتم تنظيف وكنس األسطح من األتربة وإزالة الزراجين وبقايا الخرسانة جيدًا. .2
إذا كان العزل ألسطح المباني يتم عمل خرسانة الميول لضبط ميول األسطح لتصريف مياه األمطار للجرجوري. .3
اعمال التركيب
28
يتم عمل طبقة حماية من الخرسانة العادية سمك 5سم مع عمل اختبار نفاذية المياه. .4
يتم تركيب ألواح العزل الحراري فوق الطبقة السابقة مع عمل طبقة لياسة (حماية) أسمنتية ناعمة بالميول المطلوبة .5
يتم تركيب البالط األسمنتي ( )۲۰۰ × ۲۰۰مم فوق طبقة اللياسة مع تركيب البالط األسمنتي على الحوائط وبميل حتى ال تسمح .6
بتسرب مياه األمطار من على الجوانب.
29
ثامنا -األعمال المعدنية
أعمال االلوميتال
تركيب الشبابيك االلوميتال
يتم توريد شبابيك االلوميتال بكامل اإلكسسوارات فرز أول وتشمل جميع القطع الالزمة لتحريك الضلف وتشغيلها وقطع القفل .1
والتثبيت مع جميع القطع الخاصة للتركيب والتثبيت في الحلوق أوالضلف مع تقديم اللوحات التفصيلية العينات لالعتماد من جهة
االستشاري.
يتم توريد وتركيب حلق من الخشب (حلق زفر) باألبعاد واألشكال المبينة بالرسومات مع ضبط رأسية الحلق اخذ لقطة من شرب .2
معتمد وتثبيت الحلق بواسطة الكانات بحيث ال تقل عن 3كانات لكل جنب بالميزان مع ثم يتم التثبيت مع المباني بمونة األسمنت
والرمل ومع الحلق بمسامير برمه بالطول المناسب.
يتم تركيب الشبابيك االلوميتال مع الحلق الخشب بالمنسوب المطلوب وضبط زوايا الشباك مع الحلق االلوميتال مع تجربة فتح وغلق .3
الشباك والتأكد إتمام العمل طبقا للمواصفات الفنية وأصول الصناعة والحصول على الدقة المطلوبة حتى ال تتعرض للرفض من قبل
االستشاري.
تركب الواح الزجاج داخل مجري من المطاط الطري على شكل ( )Uوبالمقاسات المناسبة للقطاعات المعدنية. .4
تركيب البوابات الحديد المشغول.
يتم توريد البوابات الكريتال بكامل اإلكسسوارات والخردوات مع تقديم عينات تفصيلية لالعتماد من االستشاري. .1
يتم تركيب البوابات الكريتال بواسطة كانات حديد بطول ال يقل عن 15سم مثبتة في العمود الخرساني على األقل 3كانات لكل جنب .2
مع ضبط رأسية البوابة مع أخذ شرب معتمد عند تركيب البوابة والتثبيت الجيد بلحام الكانات حلق البوابة والتحبيش الجيد حول
الكانات
يتم التأميم حول حلق البوابة ونهو االعمال ثم يتم دهان وجه ببوية مانعة للصدأ برايمر ثم يتم تلقيط معجون حديد لألجزاء المطلوبة .3
(اللحامات) ثم عمل وجهين ببوية الكريتال (طبقة الكية) باللون المطلوب باستخدام الكوميروسر ونهو األعمال طبقا للموصفات الفنية
وأصول الصناعة.
ب -أعمال ()STEEL STRUCTURE
أعمال تركيب مظلة من الحديد المجلفن
يتم تثبيت بالتة من الحديد المجلفن مع شبكة الحديد المسلح للقواعد والتي تكون بمقاس ( )٢ × 40 × 40سم أو بالمقاس الموضح .1
بالرسومات التنفيذية والتي بها 4جاكات لربط قاعدة العمود الحديد عليها بواسطة انكربول (صامولة التثبيت) حسب المقاس المطلوب
40مم 60/سم /عدد 4مع ضبط افقية البالتة مع مركز القاعدة المسلحة عند سطح القاعدة.
يتم ربط كمرات التغطية مع األعمدة الحديد حسب المقاسات واألبعاد الموضحة باللوحات التنفيذية. .2
30
يتم التجميع باللحام مع المحافظة على وضع األجزاء التي سيتم لحامها في أماكنها تمامًا أثناء عملية اللحام والتي سوف يكون لحامها .3
Filet Weldedلذا البد أن تكون متالصقة تمامًا.
يجب تجنب وجود فراغ ناشئ نتيجة المصنعية الرديئة أو عدم ركوب األجزاء مع بعضها وإذا حدث فراغ كبير في مكان ما فيجب .4
زيادة اللحام Filetفي هذه األماكن بمقدار هذا الفراغ.
يكون اللحام بطريقة القوس المعدني بحيث يوافق متطلبات المواصفات القياسية وأصول الصناعة ورشة اللحام والمهمات .5
يتم عمل التقويات الالزمة ( )bracingلألعمدة الحديد طبقًا للقطاعات الواردة باللوحات وكذلك عمل التغطيات ()sheet steel .6
بالمقاس المطلوب مع تركيب نظام تصريف المطر واللحام الجيد للقطاعات طبقا ألصول الصناعة
يتم دهان وجهة بمادة مانعة للصدأ (بريمر) ثم الدهان بوجهيين ببوية الكريتال (الكيه) مع استخدام المعجون الحديد في أماكن .7
اللحامات ورش بوية الكريتال باستخدام الكومبروسر وذلك حسب اللون المطلوب ونهو األعمال طبقًا للمواصفات الفنية وأصول
الصناعة.
المسئول عن
المعدات المطلوبة
مالحظات التنفيذ خطوات تنفيذ البند اسم البند م
ومواصفاتها
(مقاول – ذاتي)
اعتماد التأكد من توافر الموارد البشرية والمعدات
الكتالوجات والمواد الالزمة لألعمال
ومستندات
السالمة والصحة التأكد من تطبيق اشتراطات
تصريح العمل الطلمبة
المهنية والبيئة
دليل من خيط وميزان
اعتماد طراز وكتالوج الطلمبات
وشريط قياس
1
مفاتيح وونش بالنكو تثبيت الطلمبات على شاسيه وتركيب خطوط
ومسامير السحب والطرد
31
الكتالوجات
ومستندات
االوناش
اعتماد كابالت اعمال توصيل كابالت الكهرباء للطلمبات
الكهرباء واالختبار
تصريح العمل
المهنية والبيئة
اعتماد المخطط للوحات الضغط المنخفض
اعتماد المورد مهمات لوحات الكهرباء
والمورد
1
توريد مهمات لوحات الكهرباء
2
استخراج التصاريح الالزمة
(مصنعيات)
مقاول باطن
32
توريد الكابالت استالم الكابالت مع شهادة اختبار من المصنع
إطالق التيار
33
ρέϳϘΔΗϧϔϳΫ
ΧΗΑ
Ύέ ϟΗ γέϳΏϠ
ϟϣρ
ΎΑϖ
šœſ
ƆſʮȆ¦
ƆʙƄŗ ʮȆƃƃʯʹʻ
ʯʹŽ
ʘʻʘ
řʙ ʻؕ ʔ ¦ƃʗ °« – œ
¸ ¦ƙƈȏœ
ſʯœ
ƌ
Ɔ°Ŷƃ
œʱƆ
ƆȆ ¦¦ʻȜ
ʥʱŗż ŮȆ
ŵʵœ
ʦŮ ¾¦
řʸȆ– ƃʯ ʵʠʻ ʔƃƄ ʸʠʮȖ (
řʠʮʻ ʔ ¦ƃŽʙŵ
œ©ǺʠƊŤɽ
ŽƊ
Ɗ .) –
ʓśʙŵƄƑ¦ƙŤ
Ƒƙřʓśʙŵ ʯœ°
ƄƑƙŤॺʯ .
ƃ¦ ʸʦ¦°®¦ƃॺ ʵʙ
Ȃŗ
ŵœ
ʸ¾ř ʵʠʻœ©Ɔʗ ȁʻ
°ʥŵ¦Ťʯœ°¦
ƄƑŤॺ ʯƃƃʯʯ ʴʙȂȂ ʔʔ
ʴʙ .
Ɔ ʵʙ »Ɔʙ ¦ɾॺŗ¦ ŵœ
ʸ¾Ɔʗƈ ॻŗॻ ¦ƃŶ
ƃʯʦŞƊœʸƃƊ.
ॻ
Ɔƌʹʗ ²řʹ ŽœƂʗƆʥ
ʘ Ūʻʙ¦ƙŤʯʯ
ʻƃƄʯƂʗƆʥŪʻʙƙŤ œ°
ॺǺʠʙ
ǺʠʙȂƀŗ Ůʲ
ȂƀŗŮ ॻʲŗ
ʲ ʲŗ .
¦Ŷʗ®Â¦ƕ®Â¦©¦ƃ ʸ ʯ
ƃ ʴ ʳʗƆŗ
Şॺॺ ʛ¦ Ū ʸʹ ʕƃʚŵ
¿¦ŵʸ
œ
ƃ¾¦ƃʠœ©
ʸʠ ॺ .
Ɔœ
ॻƉॻॺ Žƈʢƃ¦Ɗʸʠ
ƃƄʸʮŐ
Ȗƃ
ƃʚʸʠ
ÂʮȖ
¿¦ƙŤʯœ°
ॺʯ
ƃʚƙŤ .
ॺŵʗ®ƒ ʗȂ
ÂƊƃʚř
¿řʴؒʴؒʻʙ¦ƃʠœ©
ʻʙƃʠ ॺ .
ƈʚ¬¦
ȖƈʚƃƃʸƉ
œƉ
ʸॻǺŶʗƙƈ
ǺŶʗ¦ƙƈ
ʯƌƆʯƌ
œ Ɔʥ¦ƙŤ
ʯ ʯœ°
ʥƙŤ ॺ .
Ťʠʦ¦©ŵ ʸȆ ¦ ƙŤʯ
ϡ
¦ʯŋƂʗ
ƃ œ
ƆżŗÂŞœ
Ž ƃ»¦ƃʸʠ
ʥƈʢżŗŞ ʸʠ
ʮȖʮȖ .
¦ʯŋƂʗƆƃ¦ʥŪ
ƃ źʠ
œ ƃƆ
ƚƄʸʠʮƃ
ŗƃźʠȖƄ ʸʠʮȖ .
Ūœŵŗ 42 Ȗʮʠ ʸƃ¦½ʙřʤʯȂ ȏœ
° ʵʯŪƙ ¦ ² ʗʹƌ ʸƃ¦©œʸॻƄ ʻƆ §ʙ ʵƃȖʮʠ ʸƃ¦ŐƄ
Ŷʯŕʥ Ŷ Ɔʤʯƒ
ॺœƄ ʸʦ ¦ Ůœ
ʟƀƃ Ž ©¦ƃŽʹƊ
ॻ ƃ¸
Ƅ ʸ ʵʙ .
œ
¦ƙǺ°Şƌ
ʲœ±¦ƙ Ŭʙ¦ »
ʷʦŞƌƙŬʙ .
ȂƚŞƌ
ʯʤ¤ŵ
œ
Ȃʯ®¨
ʤŵ
. ʮʠ ʸƃ¦
Ȗ Âœ ° ॺʯŤƙ ¦ŗƆƚŪʥƆ ʗƂŋʯƃ¦ʤʯƒƑʯš ȏʙŤ ¦ƉʙƆ œ
° ॺʯŤƙ ¦
œƉ°ŬŠ
ॻŬ
Ɖ ʲ ʡŗ:
ƆƄ ʦ
. ʮʠ ʸƃ¦ȆŤ ®Ɖ
Ȗ ¦ œॻʸƄƃ ʔȂʙ ʴ řȏ ¢®ʦŞʦ੠ʸ ʴ ǻƙÂȖʮʠ ʸƃ¦¾ʦš Ƒő
œƆ ȏʙ ʱƆ ¦
34
إجراءات الجودة
يتم عمل محضر باالختبار مرفق لوحة موضح عليها أماكن المطابق
وفي حالة حدوث فشل لالختبار يتم عمل تقرير عدم مطابقة للمطبق الفاشل في االختبار .
35
محضر اختبار تسريب مطابق
انه ف يوم ................الموافق ........... / ........... / ...............اجتمعت اللجنة المشكلة من كال من :
تم المرور علي المطابق الموضحة بالجدول للمشروع سالف الذكر وتم ملئ المطابق بالماء بتاريخ ........... / ........... / ...............
وبعد اكتمال ملئ المطابق تم تركيب غطاء المطبق والتقفيل والتحبيش علي الغطاء بخلطة مونه وجبس وترك المطابق لمدة 24ساعة
وبعد ذلك تم كشف الغطاء بتاريخ ........... / ............ / .................والنتائج طبقا للبيان التالي وطبقا للصور المرفقة -:
التوقيعات - :
........................................... ..........................................
............................................ ..........................................
36
Method Statement –
Installations
Electrical Works
37
METHOD STATEMENT
FOR
TRANSFORMER INSTALLATION
TABLE OF CONTENTS
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
38
1.SCOPE
This procedure to clear the method of the supply, installations of Transformer for the project.
This document details Transformer Installation:
1. Preparation of work.
2. Delivery and inspection upon arrival of material at site.
3. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
4. OPERATION
Material:
39
The sizes and routes routing will be as per the approved Shop Drawings.
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
Pre-Installation:
All materials and documentation relevant to this particular section of works shall be checked
by the Construction Department prior to the commencement of works ensuring that these are
correct and approved type.
Before any permanent works will continue, pre-inspection on all materials, tools and access
for installation to be carried out.
Installation:
Before the transformer will be delivered to site, ensure that the transformer railing is fixed as
per approved drawings and comply on municipality requirement.
Move the transformers from the designated off-loading area or storage area using fork lift and
set them in position near to the transformer room.
Make sure that the orientation of the transformer with regards to the position of cable entries
is correct.
Push in the transformers inside the transformer room. Set the transformer on their final
positions and make sure that they are properly secured and protected.
Raise Request for Inspection for Transformer Installation.
Conduct on site test for the transformer.
Test shall include winding insulation resistance test and shall conform to manufacturer’s
recommendation and specification.
All tests must be recorded and conducted in the presence of Consultant by manufacturer
testing engineer.
40
Dress and terminate the incoming and outgoing cables on the transformers.
Ensure that the cables were supported properly.
Cable glands, lugs and termination kits shall be approved type.
After termination works has been completed, clean the transformer cable box and ensure
that it is free from foreign materials and excess openings must be sealed off and ensure that
all the connections are properly tight and torque.
Raise Request for Inspection for the cable terminations and dressing.
Commissioning:
Cover the cable boxes.
Bolts and nuts must be tightened properly.
Make sure that the transformer room is clean and free from foreign materials.
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and correct
operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shopdrawings and specs and manufacturer
recommendations.
6. RESPONSIBILITIES
PROJECT MANAGER
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
41
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
5. To control disposal of waste materials according to the instructions received from the
site engineer.
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
42
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
1. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
2. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians
8. MATERIALS REQUIREMENTS
Transformer Components and Accessories
43
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Transformer Installation will be as follows:
1. Hand Tools
3. Diagonal-Cutting Pliers
5. Side-Cutting Pliers
10. P.P.E. – Personal Protective Equipment (safety helmet, Boots, gloves & safety vest )
44
12. SUPPORTING DOCUMENTATION
This method Statement should be read in conjunction with the below referenced
documentations:
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information / action /
comments:
1. Project Manager
2. Site Engineer
3. Foremen
4. Safety Engineer
6. Store Keeper
45
METHOD STATEMENT
FOR
LOW VOLTAGE DISTRIBUTION BOARD
TABLE OF CONTENTS
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
46
1.SCOPE
This procedure to clear the method of the supply, installations of Electrical PanelBoards for
the project.
This document details the Electrical PanelBoards Installation:
4. Preparation of work.
5. Delivery and inspection upon arrival of material at site.
6. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
4. OPERATION
Material:
47
Material used will be as approved by the Engineer.
The sizes and routes routing will be as per the approved Shop Drawings.
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
All materials and documentation relevant to this particular section of works will be checked
and verified ensuring that these are correct and approved type.
Prior to the commencement of works, ensure that the areas for permanent installation are
ready, accessible and in suitable condition.
Installation:
Before beginning installation in any area, examine all parts of the adjoining works into
which applicable work is to be placed. Should any condition be found which will
prevent the proper execution of the work, installation shall not proceed in that area
until such conditions are corrected by the contractor.
Fix all equipment independently of wiring system. Use cadmium of zinc electroplated
bolts, nuts, washers and screw.
Mount single DB at 1800mm from finish floor level to top of equipment, unless shown
otherwise on drawing / schedules.
Ensures that clearance in front of switchgear is not less than 1m, or as indicated.
Number terminals, cables and component parts to correspond with manufacturer have
certified drawings.
48
Terminate PVC, SWA PVC and MICS cables inside enclosure by securing cables to
switchboards with gland bracket; and enclosure with glanding plates or fabricated
steel extension boxes.
For flush installation, DB’s all conductors shall terminate behind the board in an adaptable
box. For surface mounting, trunking shall be fixed between the board and ceiling or floor
level, or conduit run directly into Trunking which prevent correct installation of the Trunking
lid. Adequate earth continuity shall be made between the various components.
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and correct
operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shopdrawings and specs and manufacturer
recommendations.
6. RESPONSIBILITIES
PROJECT MANAGER
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
49
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
5. To control disposal of waste materials according to the instructions received from the
site engineer.
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
50
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
1. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
2. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians
8. MATERIALS REQUIREMENTS
Electrical PanelBoards Components and Accessories
51
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Electrical PanelBoards Installation will be as follows:
1. Wire cutters
2. Measuring tape
3. Drill machine
4. Wooden hammer
5. Flat file
6. Screw drivers
8. Crimping tool
52
12. SUPPORTING DOCUMENTATION
This method Statement should be read in conjunction with the below referenced
documentations:
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information / action /
comments:
1. Project Manager
2. Site Engineer
3. Foremen
4. Safety Engineer
6. Store Keeper
53
METHOD STATEMENT
FOR
DIESEL GENERATOR INSTALLATION
TABLE OF CONTENTS
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
54
1.SCOPE
This procedure to clear the method of the supply, installations of Diesel Generator for the
project.
This document details Diesel Generator Installation:
7. Preparation of work.
8. Delivery and inspection upon arrival of material at site.
9. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
4. OPERATION
Material:
55
Material used will be as approved by the Engineer.
The sizes and routes routing will be as per the approved Shop Drawings.
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
Pre-Installation:
All materials and documentation relevant to this particular section of works shall be checked
prior to the installation.
Make sure that the plinth is completed and painted and ready for final installation of
equipment.
Make sure that the generator room is clear and free of debris and foreign materials.
Ensure that the access for generator set installation is free from obstructions.
Make sure that supporting flanks, pipe rollers, chain blocks, hydraulic jacks and other tools
required for installation are in place.
Installation:
Lift the Generator using mobile crane or portable hydraulic crocodile jack. Place pipe rollers
under the generator skid. Make sure that the pipe rollers are properly set.
Once the generator set will sit on the pipe rollers, push in / pull in the generator set inside the
room. If required, use chain block to pull the generator set. Make sure that the chain block is
properly anchored and properly set to the direction of generator position.
Where in a generator set crosses a trench or unequal elevation, use steel channels or I-
beams to support the pipe rollers. Make sure that the steel channels or I-beams are properly
56
supported to carry the weight of the Generator set.
Set the Generator set in proper location. Lift the Generator set using portable crocodile
hydraulic jack and let it sit on elevated flanks or I-beams.
Fix the spring vibration isolator. Ensure that it is fixed and aligned properly.
Lift the Generator set and install the spring vibration isolator. Bolt and tight properly the
Generator base on to the spring vibration isolators.
Associated work related to the Generator set such as generator exhaust system, fuel system,
acoustic lining etc, will commence.
After completing all associated works related to the Generator set, raise a Request for
Inspection for Generator Installation.
Commissioning:
Test the Generator in accordance to specification and manufacturer recommendation.
All testing will be carried out in the presence of Consultant.
Test shall be carried out by the manufacturer’s testing engineers.
All test sheet shall be certified by the manufacturer representative.
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and correct
operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shopdrawings and specs and manufacturer
recommendations.
6. RESPONSIBILITIES
PROJECT MANAGER
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
57
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
5. To control disposal of waste materials according to the instructions received from the
site engineer.
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
58
7. To inform the site engineer regarding areas ready for inspection.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
3. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
4. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians
59
8. MATERIALS REQUIREMENTS
Diesel Generator Components and Accessories
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Diesel Generator Installation will be as follows:
1. Hand Tools
3. Diagonal-Cutting Pliers
5. Side-Cutting Pliers
10. P.P.E. – Personal Protective Equipment (safety helmet, Boots, gloves & safety vest )
60
Permit to work at height > 2m where applicable
Lifting operation permit (using crane) where applicable.
Confined space permit where applicable.
Approved work method statement and risk assessment will be made available to site.
All workers doing the work shall be briefed on this method statement and risk assessment.
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information / action /
comments:
7. Project Manager
8. Site Engineer
9. Foremen
METHOD STATEMENT
FOR
MV POWER CABLE PULLING AND INSTALLATION
61
TABLE OF CONTENTS
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
1.SCOPE
This procedure to clear the method of the supply, Installations and Pulling of MV Cable .
This document details Installation and Pulling of MV Cable :
10. Preparation of work.
11. Delivery and inspection upon arrival of material at site.
62
12. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
4. OPERATION
Material:
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
63
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
Excavation:
1. Permit to Work (PTW) shall be raised for the excavation clearly mentioning the location of
work, size of excavation and levels.
2. Excavations area shall be surveyed and marked to the lines and levels as shown on the
drawings.
3. The area of excavation will be cordoned off using safety devices.
4. Ensure the working area at any confined space is free from any Hazardous Gas by proper
Gas testing using the Gas testing instrument.
Materials:
1. Not necessary for the construction shall be removed carefully and stored neatly for
reinstating after the construction works.
2. The material received from the client shall be stored in designated area of store.
3. Arrangements shall be made to protect against effects of weather and environment.
Pulling:
1. Insulation resistance of the cables shall be checked before laying cables.
2. After the test, the end of the cable shall be sealed to prevent the ingress of moisture.
3. Location of the panels / equipment shall be identified.
4. Cables shall be lubricated if bends in conduits are encountered in a run to facilitate drawing
in.
5. Cables must not be bent to a radius of less than 12 times the overall diameter of the cable.
6. Rollers must be used where cables are installed in an open trench using a pulling rope and
eye; cable rollers are to be used at frequent intervals to support the cables and must never
be more than 3 meters apart.
7. The rollers are to be placed securely to prevent movement.
8. The pulling rope must be equipped with a swivel and be attached to the cable by a stocking
grip with pulling eye.
9. The cable drum intended for cable pulling shall be identified as per that indicated in the drum
schedule.
64
10. The cable drums shall be un-packed and placed on a cable roller, as required.
11. Cable laying will generally start from one end of the route length or at any suitable point, as
necessary.
12. Depending on the weight and size of the drum, suitable size of the cable rolling shaft
(Spindle) shall be placed inside the central axis of the drum.
13. Suitable jacks shall be placed firmly on the ground and jackedup to allow clearance from the
ground depending on the size of the cable drum.
14. The drum shall be lifted by required equipment and placed on the jacks.
15. The cable drum will be correctly positioned and the direction of cable pulling as indicated by
arrow on the drum shall be complied.
16. The cable shall be drawn into the trench smoothly with a minimum of stops and at an
average speed of between 9-12 meters per minute, to avoid irregular movement.
Termination:
1. Termination point inside the panels / equipment shall be considered for suitable spare length
to be left available during pulling of cable termination.
2. After cutting the cable to the required length the termination work will be conducted as per
ADDC Standard.
3. Jointing and Termination will be carried out as per ADDC standards. All jointing and
termination work will be carried out by trained technicians, experienced in such work for the
operating voltage concerned.
4. Proper crimping tools shall be used compression type lugs. All cables are to be terminated
used glands of proper type and size as per area classification.
5. The gland shall be assembled strictly in accordance with manufacturer’s instruction,
particular attention being paid to ensure good mechanical and electrical contact between part
without excessive strain or distortion of cable.
6. The entire body of the cable must enter the gland. The cable shall be on a straight axis from
a point at least six diameter before entering the gland. Seals shall be checked for correct size
at the point of application.
7. Unused cable entries shall be closed with plug suitable for the degree of protection
classification.
8. After completion of indoor and outdoor termination the cable is ready for Testing.
Commissioning:
1. The following calibrated testing instruments will be used:
1 KV / 5 KV IR Test Kit - 1 no.
Multi Meter - 1 no.
Continuity Tester - 1 no.
Continuity Tester - 1 no.
Torque wrench - 1 no.
VLF - Test Kit.
2. Before starting the test, the corresponding Circuit Breakers at
65
both ends of the cables are racked out and earthed properly.
3. Test will be conducted at the MV panel end. The opposite end of the cable termination will be
secured & protected. Testing engineer will be at the end where high voltage is applied and
another Engineer to monitor at the opposite end of the cable.
4. Insulation Resistance will be done first: (a) between termination lugs; (b) Phase, Neutral and
Earth termination lug; (c) conductor to termination lug. This will be done one minute each at
5kV, and the results are noted as per approved test report format.
5. The continuity test and phase sequence tests would be carried out and results would be
recorded for records and future reference.
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and correct
operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shopdrawings, approved specs and
manufacturer recommendations.
6. RESPONSIBILITIES
PROJECT MANAGER
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
66
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
5. To control disposal of waste materials according to the instructions received from the
site engineer.
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
67
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
5. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
6. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians
8. MATERIALS REQUIREMENTS
MV Cable Components and Accessories.
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Installation and Pulling of MV Cable will be as follows:
1. Cable Rollers
2. Cable Pulling Grip
3. Hand Cable cutter
4. Manual Cable Crimpers
5. Hacksaw blade
6. Power Tools
68
7. Tool Box
8. Measuring Tape
9. Ladders / Scaffoldings/Platform
10. Hand tools Hilti Drill Machine
11. Hilti Concrete Bit (6mm to 16 mm)
12. Anchor Bolt/Screw
13. Screw Driver
14. Adjustable Spanner
15. Hammer
16. Electrician’s Knife
17. Multi Meter
18. 1 KV / 5 KV IR Test Kit
19. Continuity Tester
20. Torque wrench
21. VLF – Test Kit
69
Insulation Resistance and continuity Test Report.
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information/ action/ comments:
15. Foremen
METHOD STATEMENT
FOR
LOW VOLTAGE CABLES INSTALLATION
TABLE OF CONTENTS
70
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
1.SCOPE
This procedure to clear the method of the supply, installations of Wires and Cables for the
project.
This document details Wires and Cables Installation:
13. Preparation of work.
14. Delivery and inspection upon arrival of material at site.
71
15. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
4. OPERATION
Material:
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
72
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
o Prior to the commencement of works, ensure that the areas for permanent installation are
ready, accessible and in suitable condition.
Excavation:
No wiring be carried out until the appropriate tests required or in the electrical testing
section have been done and the consultant has given his clearance for wiring to
commence.
A loop in form of wiring shall be used as far as practicable or unless otherwise indicated.
Joints in conductors shall be made using insulated terminal blocks complying with
requirements of this specification.
At expansion joints adequate slack shall be left in the cable.
Where Conduits are installed for wiring by others, a draw wire shall be provided between
each draw in position.
Where three-phase circuits comprising single-core cables are installed in trunking, all
cables of a shall be tied together at intervals not exceeding 200mm.
Cables forming part of alarm, control, communication or monitoring circuits shall have
identification sleeves at their terminations. Identification shall be consistent with the
relevant wiring diagrams.
Pulling:
Make sure that all conduits and boxes in both ends are free from
damages and blockages etc and installation is approved.
Blockage shall be checked by inserting the draw wire and checking
that it reaches to the other end without any disturbance.
Once the conduit is not blocked the wires shall be pulled using the
draw wires while ensuring no damage occurs while pulling.
Pulling compound or lubricant shall be used for pulling the wires
where required.
Use soap based pulling compound for short runs i.e. less than 20
meters for semi conductive insulated wires.
Use wax based pulling compound for the runs greater than 20
meters for semi conductive insulated wires.
While pulling the wires care should be taken to not insert the pull tension greater than the
manufacturer allowed limits.
73
Termination::
Erect scaffolding where required as per the site requirements.
Cable rollers shall be placed under the cable during pulling over
longer distances and standoff rollers for acute bends, to ensure that
the cable is pulled with minimum effort and the cable outer jacket is
free of scouring lines.
The cable shall be pulled by using pulling means such as fish tape, rope and basket
weave wire/cable grips so as not to damage cable or its containment system. Care will be
taken to ensure that the maximum pulling tension of all the cables is not exceeded at any
time.
Cable should be free of any static load i.e. to be places side by side parallel on the cable
tray or ladders. Any kind of dead weight on the cable shall be avoided.
The cables shall be secured to the containment system using approved cable ties for
horizontal runs and cable cleats for vertical
runs.
Termination shall be done by using the approved termination
materials that include glands, lugs and other accessories part of
termination kit, by using proper crimping tools. Matching colour gland sheaths shall be
provided.
Commissioning:
Set the Meggar meter to 1000 volts DC for cables and 500 volts DC for wires.
Take reading between phase, phase and neutral, phase and earth neutral and earth.
Note that resistance reading must not exceed 2 megaohms(MΩ).
Check and record the resistance readings as per specification on
the approved insulation resistance test forms.
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and
correct operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shopdrawings and specs and manufacturer
recommendations.
6. RESPONSIBILITIES
PROJECT MANAGER
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
74
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
5. To control disposal of waste materials according to the instructions received from the
site engineer.
75
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
7. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
8. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
76
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians
8. MATERIALS REQUIREMENTS
Wires and Cables Components and Accessories
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Wires and Cables Installation will be as follows:
o Measuring tape
o Cutting plier
o Bending spring
o Pipe Wrench
o Drilling Machine
o Crimping tool
o Screw driver
o Pulling spring
o Hammer
o Common tools
The Rubbish which would be created from our scope of works will be disposed to the designated
dumping ground.
77
11. SPECIAL CONTROL MEASURES
The following general control measures against Safety, Environment and Quality shall be
required for our scope of work and special control measures are not applicable for us :
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information / action /
comments:
21. Foremen
78
24. Store Keeper
METHOD STATEMENT
FOR
EARTHING SYSTEM INSTALLATION
TABLE OF CONTENTS
79
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
1.SCOPE
This procedure to clear the method of the supply, installations of Earthing System for the
project.
This document details the Earthing System Installation:
16. Preparation of work.
17. Delivery and inspection upon arrival of material at site.
80
18. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
4. OPERATION
Material:
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
81
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
Installation:
Coordinate installation of earthing system system with installation of other building systems
and components, including electrical wiring, supporting structures, metal bodies requiring
bonding to earthing system, and building finishes.
Install conductors with direct paths from ground pits to ground connections.
When different metal to be connected, a bimetallic clamp shall be used.
Bond roof vents, flashing and any other metal masses projecting through the roof to the grid.
Thermo weld all connections between cables and ground rods. Compression type connectors
may be used where approved by the Consultant.
Measure the resistance of the complete installation and submit for review to the Consultant.
Test clamps shall be provided in each inspection pit to allow for testing and commissioning.
Concrete inspection pits with cover shall be installed flush with finished floor level and be fully
accessible.
The complete installation shall be tested and inspected to ensure that it complies with the
requirements of the Specification and the Local Authorities. The tests shall be carried out in
accordance with the Regulations and to the satisfaction of the Consultant.
Commissioning:
The inspection and tests shall be carried out in the same sequence as set out in the
Regulations, Local Authorities and the Consultant requirements and in such time as to allow
any remedial work to be completed prior to Practical Completion.
All instruments necessary for inspection and testing shall be supplied and shall be properly
calibrated and operated by personnel skilled in their use.
Allowance shall be made for disconnection or similar operations to satisfy the requirements
for testing, etc., and the reinstatement of the installation.
Measure earth resistance not less than two full days after the last trace of precipitation and
without the soil being moistened by any means other than natural drainage or seepage and
without any chemical treatment or other artificial means of reducing natural earth resistance.
82
Where resistance to earth exceeds specified values, notify the Consultant the same and
include recommendations to reduce earth resistance and to accomplish recommended work.
Restore surface features at areas disturbed by work of this section.
Restore areas disturbed by trenching, storing or dirt, cable laying, and other activities to their
original condition..
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and correct
operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shop drawings, approved specs and
manufacturer recommendations.
6. RESPONSIBILITIES
PROJECT MANAGER
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
83
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
5. To control disposal of waste materials according to the instructions received from the
site engineer.
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
84
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
9. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
10. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians
8. MATERIALS REQUIREMENTS
Earthing System Components and Accessories.
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Earthing System Installation will be as follows:
1. Hand Tools
85
2. Power Tools (if required)
3. Diagonal-Cutting Pliers
5. Side-Cutting Pliers
10. P.P.E. – Personal Protective Equipment (safety helmet, Boots, gloves & safety vest )
86
ITP for Anti – termite Treatment.
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information/ action/ comments:
27. Foremen
METHOD STATEMENT
FOR
87
FIRE ALARM SYSTEM INSTALLATION
TABLE OF CONTENTS
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
88
1. SCOPE
This procedure to clear the method of the supply, installations of Fire Alarm system for the
project.
This document details the Fire Alarm system Installation:
19. Preparation of work.
20. Delivery and inspection upon arrival of material at site.
21. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
Specific safety measures have to follow as applicable, and all the safety measures are covered
separately in the project safety plan.
4. OPERATION
Material:
89
Material used will be as approved by the Engineer.
The sizes and routes routing will be as per the approved Shop Drawings.
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
Make sure that civil clearance done prior to start the installation.
Installation will be carried out as per manufacturer recommendations Approved shop
drawings and project specifications.
Installation:
Verify that hardware and devices are NRTL listed for use with fire-alarm system before
making connections.
Make addressable connections with a supervised interface device to the following devices
and systems.
Install the interface device less than 3 feet (1 m) from the device controller.
Make an addressable confirmation connection when such feedback is available at the device
or system being controlled as follows :
1. Alarm-initiating connection to smoke-control system (smoke management) at fire-fighter
smoke-control system panel.
2. Alarm-initiating connection to stairwell and elevator-shaft pressurization systems.
3. Smoke dampers in air ducts of designated air-conditioning duct systems.
4. Alarm-initiating connection to elevator recall system and components.
5. Alarm-initiating connection to activate emergency lighting control.
6. Alarm-initiating connection to activate emergency shutoffs for gas and fuel supplies.
7. Supervisory connections at valve supervisory switches.
8. Supervisory connections at low-air-pressure switch of each dry-pipe sprinkler system.
9. Supervisory connections at elevator shunt trip breaker.
10. Supervisory connections at fire-pump power failure including a dead-phase or phase reversal
condition.
11. Supervisory connections at fire-pump engine control panel.
90
Installation of Components:
The devices/peripherals (Smoke detectors, heat detectors, break glass, duct detectors, beam
detectors, control and monitoring modules) are connected in Class A circuit with the Control
panels.
The speakers & speaker with strobes are connected in Class A circuit with the Control
panels.
2 Core 1.5mm2 FP 200 cable to be used for cabling the Initiating Device Circuits (IDC) to the
panel, additional 2c x 2.5mm2 FP200 cable is required for the smoke detector with sounder
base for the activation of the sounders units.
2 core 1.5mm2 FP 200 cable to be used for cabling the Speakers with the panel, additional
2c x 2.5mm2 FP200 cable is required from the FACP for the speaker with strobe for the
activation of the strobe unit allied in vertical walls the run of conduit will be kept straight.
Comply with NFPA 72 for installation of fire-alarm equipment.
Smoke-Detector OR Heat-Detector
Comply with NFPA 72, “Smoke-Sensing Fire Detectors” & “Heat-Sensing Fire Detectors”.
Smooth ceiling spacing shall not exceed 30 feet (9 m).
Fire-Alarm Control Unit: Surface mounted, with tops of cabinets not more than 72 inches
(1830 mm) above the finished floor.
Annunciator: Install with top of panel not more than 72 inches (1830 mm) above the finished
floor.
91
AHUS’, FAHU’S, Lifts, Access Controlled Doors, Public Address System etc.. Which is
required to be controlled in case of a fire situation, the Control module shall be mounted
inside recommended 4” x 4” back box and wired to the equipment to be interfaced.
Install and terminate the Monitor and Control modules as per the manufacturer instructions.
Installation of Wires:
Install cables in raceways and cable trays except within consoles, back boxes, desks, and
counters. Conceal raceway and cables except in unfinished spaces.
Using CAT-6A type cable the maximum length of the cable not exceeds more than 90
mtrs. Of manufacturer recommendation, which will provided from structural cabling system
supplier.
Comply with requirements for raceways and boxes specified in Division 26 Section
"Raceways, Boxes, Cable Tray, Cable Ladder and Trunking".
Conceal conductors and cables in accessible ceilings, walls, and floors where possible.
92
Bundle, lace, and train cables within enclosures.
Connect to terminal points with no excess and without exceeding manufacturer's
limitations on bending radius.
Grounding:
Comply with requirements in Division 26 Section "Grounding and Bonding for Electrical
Systems." for grounding conductors and connectors.
Comply with ADDC Electricity Wiring Regulations, Sections.
Bond metallic equipment to the system grounding bus bar, using not smaller than the
specified equipment grounding conductor by ADDC Electricity Wiring Regulations,
Sections.
Identification:
Identify system components, wiring, and cabling complying with ADDC Electricity Wiring
Regulations. Comply with requirements for identification specified in Division 26 Section
"Identification for Electrical Systems."
Programming
After making sure all the system installed in correct way from Subcontractor and
supplier, programming of the system must take place before final testing and
commissioning accourding to Consultant requirement and senario of the system.
Testing and commissioning of the system submitted separetly for this system
mentioned all the procedure of Testing of the system and commissioning it.
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and correct
operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shop drawings approved specs and
manufacturer recommendations.
6. RESPONSIBILITIES
PROJECT MANAGER
93
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
94
5. To control disposal of waste materials according to the instructions received from the
site engineer.
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
11. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
95
12. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians
8. MATERIALS REQUIREMENTS
FAS Components and Accessories.
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Fire Alarm System Installation will be as follows:
1. Power source
2. Drilling machine
3. Tool Box
4. Measuring Tape
5. Calibrated Ohm Meter / Multi meter
6. Ladders / Scaffoldings
7. Hammer
8. Safety requirements tools such as safety shoes, safety helmet, safety glasses, fluorescent
vest, and safety gloves to ensure maximum ability of safe work and dust mask when
required.
96
All workers doing the work shall be briefed on this method statement and risk assessment.
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information/ action/ comments:
33. Foremen
METHOD STATEMENT
FOR
STREET LIGHTING INSTALLATION
TABLE OF CONTENTS
97
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
1.SCOPE
This procedure to clear the method of the supply, Installations of Street Lighting .
This document details Installation of Street Lighting :
98
22. Preparation of work.
23. Delivery and inspection upon arrival of material at site.
24. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
4. OPERATION
Material:
99
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
100
Install indirect light fittings on the bracket / holder.
Connect power cables to the light fittings. Ensure that all connections are correct and the
fittings shall be earthed.
Fix lamps on the light fittings. Make sure that the type and color of the lamp are correct and
approved type.
Connect temporary power supply to the light fittings to check for proper operation.
Raise Request for Inspection of indirect light installation.
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and correct
operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shopdrawings, approved specs and
manufacturer recommendations.
6. RESPONSIBILITIES
PROJECT MANAGER
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
101
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
5. To control disposal of waste materials according to the instructions received from the
site engineer.
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
102
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
13. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
14. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians.
8. MATERIALS REQUIREMENTS
Street Lighting Components and Accessories.
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Installation of Lighting Fixtures will be as follows:
1. Screw drivers
2. Hacksaw
3. Needle nose pliers
4. Electrical drill and drill bits (only for surface installation works)
103
5. Diagonal-Cutting Pliers
6. Wire Stripper/Cutter with Spring
7. Side-Cutting Pliers
8. Level
9. Shank Screwdriver
10. Electrical tape
11. Voltage tester
12. P.P.E. – Personal Protective Equipment (safety helmet, Boots, gloves & safety vest )
104
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information/ action/ comments:
39. Foremen
105
INSTALLATION OF Pumps:
Scope of Work:
The method of statement is to describe the procedures involved in the installation of Pumps
including the preparation plan, Health and safety plan in accordance with the project
specification, drawings and standards.
106
o During working period responsible site supervisor and safety officer should be full time.
o Demonstration, training & awareness guideline to all employees.
o Minimizing the dust exposure to avoid pollution and any bad effect to the health of the
community and the workers also.
o The responsible person should ensure the security and safety of work area at all times.
Appropriate warning tapes, barricade should be use to communicate hazard.
o Workforces and staff will be provided with safety training and orientation prior to commencing
to work and it’s mandatory.
o Tool box meeting will cover awareness and recognition of potentially dangerous and unsafe
conditions of tapping of new sewer line at main sewer line at the site.
o Safety warning and signage’s will be post visibly were it is necessary especially
“RESTRICTED AREA “.
o Proper enough access should be made for equipment moving.
Work Instructions
Pre-Installation Stage
o Prior to the commencement of the works inspect the areas for safe access and confirm they
are in a suitable condition for the works to commence.
o All Materials and documentation relevant to this particular works shall be checked by the site
engineer to confirm adequacy and compliance to the requirements prior to the
commencement of works.
o The site supervisor shall instruct concerned workmen regarding the execution of the works,
and will ensure that necessary approved drawings are available at site.
o The supervisor will also check that necessary tools and equipment are available and correct
for the works to be carried out.
o Check the readiness of site for installation
o Only approved materials shall be issued by the Stores for all site works.
o After satisfactory completion of above steps works shall commence in the respective areas.
Installation stage
107
o Ensure the Pumps should be as per Approved Shop Drawings, Approved Material
Submittals & Project Specification.
o Ensure all details is available on the Pump for verification:
Manufactures Detail
Pressure Rating
Voltage Detail
Serial No, Part No, Made etc
o Ensure the Installation of the Pumps shall be as per Manufactures recommendations.
o Ensure the Pump panels shall be interfaced with BMS operations as per Approved Shop
Drawings & Project Specifications.
o Ensure Electrical power supply for pump panel shall be as per Approved relevant Shop
Drawings.
o Ensure the location of Pumps, valves and accessories shall be in accessible locations for
future ease of repair and maintenance.
REFERENCE DOCUMENTS
o Approved shop drawings.
o Approved materials submittal
o Material test certificates.
o Material inspection report.
o Project Specification.
108
INSTALLATION OF AIR BLOWERS:
Scope of Work:
The method of statement is to describe the procedures involved in the installation of Air
blowers including the preparation plan, Health and safety plan in accordance with the project
specification, drawings and standards.
109
o During working period responsible site supervisor and safety officer should be full time.
o Demonstration, training & awareness guideline to all employees.
o Minimizing the dust exposure to avoid pollution and any bad effect to the health of the
community and the workers also.
o The responsible person should ensure the security and safety of work area at all times.
Appropriate warning tapes, barricade should be use to communicate hazard.
o Workforces and staff will be provided with safety training and orientation prior to commencing
to work and it’s mandatory.
o Tool box meeting will cover awareness and recognition of potentially dangerous and unsafe
conditions of tapping of new sewer line at main sewer line at the site.
o Safety warning and signage’s will be post visibly were it is necessary especially
“RESTRICTED AREA “.
o Proper enough access should be made for equipment moving.
Work Instructions
Pre-Installation Stage
o Prior to the commencement of the works inspect the areas for safe access and confirm they
are in a suitable condition for the works to commence.
o All Materials and documentation relevant to this particular works shall be checked by the site
engineer to confirm adequacy and compliance to the requirements prior to the
commencement of works.
o The site supervisor shall instruct concerned workmen regarding the execution of the works,
and will ensure that necessary approved drawings are available at site.
o The supervisor will also check that necessary tools and equipment are available and correct
for the works to be carried out.
o Check the readiness of site for installation
o Only approved materials shall be issued by the Stores for all site works.
o After satisfactory completion of above steps works shall commence in the respective areas.
Installation stage
110
o Ensure the air blowers should be as per Approved Shop Drawings, Approved Material
Submittals & Project Specification.
o Ensure all details is available on the air blowers for verification:
Manufactures Detail
Pressure Rating
Voltage Detail
Serial No, Part No, Made etc
o Ensure the Installation of the air blowers shall be as per Manufactures recommendations.
o Ensure the air blowers panels shall be interfaced with BMS operations as per Approved Shop
Drawings & Project Specifications.
o Ensure Electrical power supply for panel shall be as per Approved relevant Shop Drawings.
o Ensure the location of air blowers, valves and accessories shall be in accessible locations for
future ease of repair and maintenance.
REFERENCE DOCUMENTS
o Approved shop drawings.
o Approved materials submittal
o Material test certificates.
o Material inspection report.
o Project Specification.
111
METHOD STATEMENT
FOR
LIGHTING CONTROL PANELS INSTALLATION
TABLE OF CONTENTS
1. SCOPE
2. DEFINITIONS
4. OPERATION
6. RESPONSIBILITIES
7. MANPOWER REQUIRED
8. MATERIALS REQUIREMENTS
9. EQUIPMENTS REQUIREMENTS
13. DISTRIBUTION
112
1.SCOPE
This procedure to clear the method of the supply, installations of Lighting Control Panels for
the project.
This document details Lighting Control Panels Installation :
25. Preparation of work.
26. Delivery and inspection upon arrival of material at site.
27. Installation of the system.
2. DEFINITIONS
PQP : Project Quality Plan
MS : Method Statement
4. OPERATION
Material:
113
Material used will be as approved by the Engineer.
The sizes and routes routing will be as per the approved Shop Drawings.
Deliver components parts to site, completely identified in accordance with shop and
certified CAD Drawings prepared for this work.
Store in accordance with the manufacturer’s instructions, above ground, properly protected
from the weather and construction activities.
Installation:
114
Make sure the configuration of delivered Lighting control Panels is accordance with drawing
and the authority regulations.
Make sure prior to installation, deliver Lighting control Panels are properly packaged in
factory packed or fabricated containers.
Make sure LCP are stored in a dry area, and protect from weather,fumes, water, debris, etc.
Care shall be taken to ensure that no other foreign material ingress to the installed Lighting
control Panel , and make sure installed services are sealed, covered and protected to avoid
any damage during civil works.
Technical Assistance:
The installation supervising technician for the system trade shall instruct the
CONSULTANT Engineer, and Construction Site Manager on the programming and correct
operation of the system after the installation is completed.
This instruction shall be scheduled at the convenience of the staff.
All such instruction shall be properly recorded.
WIR will be issued for Consultant approval upon making sure that the installation of the
system equipment’s done as per approved shopdrawings and specs and manufacturer
recommendations.
115
6. RESPONSIBILITIES
PROJECT MANAGER
1. To ensure that all the preparation and application works are carried out according to
the Contract Specification and with the approved drawings.
2. To ensure that the progressing of works is carried out according to the planned
program and as per the approved method of statement.
3. To ensure that all the equipment and material required executing the work are
available according to the planned construction program.
4. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe
and proper execution of the works.
SITE ENGINEER
1. To ensure that the works are carried out according to the Contract Specification,
approved method statement and the shop drawings.
3. To monitor the progress of work in relation with the work program and to report to the
Project Manager.
4. To co-ordinate with the safety officer and to ensure that the works are carried out in
safe practicing method.
FOREMAN
1. The foreman will carry out his duties by maintaining continuous coordination with the
site engineer on daily basis, and ensure proper distribution of the work force on the
required and planned locations.
2. To ensure that his assistant foreman/ charge hand are aware of the job requirements
and they have enough information to carry out their duties properly.
3. To ensure that the daily work is progressing as planned and advice the site engineer
of any requirement for additional resources.
116
4. To ensure in consultation with the site engineer that the manpower involved in the
works are moving as agreed and planned for the work.
5. To control disposal of waste materials according to the instructions received from the
site engineer.
6. To ensure full coordination with the safety officer to maintain safe working and proper
house keeping of the site, following the proved safety measures and further ensure
that all his working team are aware of the same to prevent accident and losses.
8. Foreman and the storekeeper are responsible for the distribution and control of
materials.
SAFETY ENGINEER
1. Ensure the implementation of all the safety measures in accordance with the HSE plan
and everybody aware of it for it’s proper implementation.
2. Ensure all the implemented safety measures are adequate to maintain safe working
on the site.
3. Inspect all the site activities and train the person to prevent accidents and it’s proper
implementation.
STORE KEEPER
117
15. Responsible for overall Store operations in making sure to store the material
delivery to the site and keep it in suitable area that will keep the material in safe
from rusty and damage.
16. One who will acknowledge the receiving of materials at site in coordination with
QA/QC and concerned Engineer.
7. MANPOWER REQUIRED
Charge hand and Experienced Technicians
8. MATERIALS REQUIREMENTS
Lighting Control Panels Components and Accessories
9. EQUIPMENTS REQUIREMENTS
The Equipment that will be engaged for Lighting Control Panels Installation will be as follows:
1. Hand Tools .
3. Diagonal-Cutting Pliers .
5. Side-Cutting Pliers .
8. Measuring Tape .
9. Multi Meter .
118
12. P.P.E. – Personal Protective Equipment (safety helmet, Boots, gloves & safety vest )
13. DISTRIBUTION
Copy of this method statement shall be issued to the following for information / action /
comments:
119
45. Foremen
INSTALLATION OF PIPES
Scope of Work:
o The method of statement is to describe the procedures involved in the installation of piping
including the preparation plan, Health and safety plan in accordance with the project
specification, drawings and standards.
120
Personal Roles and Responsibilities
o The Site Engineer shall be responsible to ensure that all works comply with the project
specifications, drawings and standards. He shall ensure that the work is ready for inspection.
He shall raise the internal RFI to the QC Engineer and report to all concerned personnel.
o The QC Engineer shall be responsible for surveillances and inspections of works. He shall
document all inspection records and reports. He shall review all documents, certificates and
nonconformance reports. He shall receive and review the internal Request for Inspection
(RFI) and conduct internal inspection as required. He shall raise the RFI, with the required
checklist, and liaise with the Consultant representative during the inspections.
o The Site Engineer shall be responsible for inspections and tests of all materials in close
coordination with the QC Engineer, material suppliers and the Consultant Engineer. He shall
ensure that all materials and test procedures comply with the applicable standards and
specifications.
o The Safety officer shall be responsible for the safety of personnel, materials and equipment
in the area. He shall ensure that works are executed in a safe manner observing all safety
precautions at all times. He shall be responsible for securing all safety and environmental
permits prior to the start of works.
o Safety plan requires that proper regard is given to occupational and environmental safety
during all activities.
o Follow health safety & Environmental precautions in the execution of work.
o Ensure that personal protective equipment (PPE) shall be worn during working period.
o Medic should be available at all times in case of any injuries arise at the work site for first aid.
o During working period responsible site supervisor and safety officer should be full time.
o Demonstration, training & awareness guideline to all employees.
o Minimizing the dust exposure to avoid pollution and any bad effect to the health of the
community and the workers also.
121
o The responsible person should ensure the security and safety of work area at all times.
Appropriate warning tapes, barricade should be use to communicate hazard.
o Workforces and staff will be provided with safety training and orientation prior to commencing
to work and it’s mandatory.
o Tool box meeting will cover awareness and recognition of potentially dangerous and unsafe
conditions of tapping of new sewer line at main sewer line at the site.
o Safety warning and signage’s will be post visibly were it is necessary especially
“RESTRICTED AREA “.
o Proper enough access should be made for equipment moving.
Work Instructions
Pre-Installation Stage
o Prior to the commencement of the works inspect the areas for safe access and confirm they
are in a suitable condition for the works to commence.
o All Materials and documentation relevant to this particular works shall be checked by the site
engineer to confirm adequacy and compliance to the requirements prior to the
commencement of works.
o The site supervisor shall instruct concerned pipe fitters regarding the execution of the works,
and will make available necessary approved drawings on site.
o The supervisor will also check that tools and equipment available are correct for the works to
be carried out.
o Check the availability of necessary openings wherever required as per approved drawings.
o Check the readiness of site for installation.
o Co-ordination with other services to be checked and ensured.
o Only approved materials shall be issued by the Stores for all site works
o After satisfactory completion of above steps works shall commence in the respective areas.
Installation stage
o Mark the route of the Water piping on the surfaces and soffit of slab.
122
o Pipe support, spacing, location, installation of valves and pipes shall be as per approved
standard detail drawing.
o Determine the position of supports, then drill & fix the approved type of supports as per
approved drawings & Material Submittal.
o The pipes shall be cut to the required lengths as per the layout / site condition.
o The pipe & fittings shall be cleaned prior and after making thread.
o For pipes up to 50mmф the joints shall be threading method, 65mm and above shall be
welding / grooved method.
Testing:
o Pipes shall be tested in sections or floor wise as per the site conditions and requirements.
o The whole network which is going to be tested shall be filled with the water by means of
testing pump. All open ends should be plugged /blinded.
o Any air traps should be removed completely by venting at highest point.
o The test pressure shall be as per specifications. There shall be no leak observed for the
system to be approved.
o Prepare the (IR) inspection request in the approved format for submission.
123
REFERENCE DOCUMENTS
o Approved shop drawings.
o Approved materials submittal
o Material test certificates.
o Material inspection report.
o Project Specifications.
124
INSTALLATION OF SUPPLY & EXHAUST FANS
Scope of Work:
o The method of statement is to describe the procedures involved in the installation of Supply
& Exhaust Fans including the preparation plan, Health and safety plan in accordance with the
project specification, drawings and standards.
o The Site Engineer shall be responsible to ensure that all works comply with the project
specifications, drawings and standards. He shall ensure that the work is ready for inspection.
He shall raise the internal RFI to the QC Engineer and report to all concerned personnel.
o The QC Engineer shall be responsible for surveillances and inspections of works. He shall
document all inspection records and reports. He shall review all documents, certificates and
nonconformance reports. He shall receive and review the internal (Request for Inspection
(RFI) and conduct internal inspection as required. He shall raise the RFI, with the required
checklist, and liaise with the Consultant representative during the inspections.
o The Site Engineer shall be responsible for inspections and tests of all materials in close
coordination with the QC Engineer, material suppliers and the Consultant Engineer. He shall
ensure that all materials and test procedures comply with the applicable standards and
specifications.
o The Safety officer shall be responsible for the safety of personnel, materials and equipment
in the area. He shall ensure that works are executed in a safe manner observing all safety
precautions at all times. He shall be responsible for securing all safety and environmental
permits prior to the start of works.
125
Safety plan prior to the work
o Safety plan requires that proper regard is given to occupational and environmental safety
during all activities.
o Follow health safety & Environmental precautions in the execution of work.
o Ensure that personal protective equipment (PPE) shall be worn during working period.
o Medic should be available at all times in case of any injuries arise at the work site for first aid.
o During working period responsible site supervisor and safety officer should be full time.
o Demonstration, training & awareness guideline to all employees.
o Minimizing the dust exposure to avoid pollution and any bad effect to the health of the
community and the workers also.
o The responsible person should ensure the security and safety of work area at all times.
Appropriate warning tapes, barricade should be use to communicate hazard.
o Workforces and staff will be provided with safety training and orientation prior to commencing
to work and it’s mandatory.
o Tool box meeting will cover awareness and recognition of potentially dangerous and unsafe
conditions of tapping of new sewer line at main sewer line at the site.
o Safety warning and signage’s will be post visibly were it is necessary especially
“RESTRICTED AREA “.
o Proper enough access should be made for equipment moving.
Work Instructions
Pre-Installation Stage
o Prior to the commencement of the works inspect the areas for safe access and confirm they
are in a suitable condition for the work to commence.
o All Materials and documentation relevant to this particular works shall be checked by the site
engineer to confirm adequacy and compliance to the requirements prior to the
commencement of works.
o The site supervisor shall instruct concerned workman regarding the execution of the works,
and will make available necessary approved drawings on site.
126
o The supervisor will also check that tools and equipment available are correct for the works to
be carried out.
o Check the readiness of site for installation.
o Only approved materials shall be issued by the Stores for all site works
o After satisfactory completion of above steps works shall commence in the respective areas.
Installation stage
o Prior to installation the coordination with other MEP services should be ensured.
o Location, capacity and types of the fans should be checked with the approved shop drawing
and name plate of fans should be ensured for the same.
o Roof mounted fans are installed on the concrete with plinths with isolators as shown in
approved shop drawings and manufacturer’s recommendation.
o Orientation of fan with respect to duct work should be checked and ensured as per approved
drawings.
o All ceiling suspended fans should be supported properly with spring isolators, channels and
threaded rods, if any.
o All fans should be connected to ducts with flexible duct connectors as shown in the standard
detail drawings.
o All electrical connections should be made as per approved shop drawing and manufacturer’s
recommendations.
o All fans shall be protected from dust and damages by proper covering till the commissioning
stage.
REFERENCE DOCUMENTS
o Approved shop drawings.
o Approved materials submittal
o Material test certificates.
o Material inspection report.
o Project Specification
127
128
INSTALLATION OF Panels:-
o Ensure that panel type, dimensions & IP's are according to approved specification &shop
drawings.
o Ensure that panel components are identical with approved specification and layout drawing.
o Determine the location, coordinates for fixation as per approved shop drawing.
o Panel fixation should be in the best & safety location with observation inputs, outputs& site
conditions (if any obstacle exists).after agreement and approve to change due to new issue
drawings.
o Dismantle the internal and external mirrors which contained components to prevent from
break (in case of internally fixation obstacle).
o Fix the panel enclosure after determine fixation holes and using suitable anchor bolts.
o Return the internal mirror and any other internal components with observation the enclosure
protection degree (IP).
o Determine & organize the input& output conduits on input/output plate with observation the
enclosure protection degree (IP).
o Connect the internal wires and feeder cable with suitable& organize way.
o Ensure that all wires and cables have identification labels.
o Reinstall the outer mirror with observation the movable parts.
o Earthed the panel enclosure, flexible glands and flexible conduits.
o Doors components & other the movable parts should be fixed with flexible wires.
o Clean the enclosure from remaining wires and dust.
o Check and test all fuses and indication lamps to ensure it's validity.
o Touch up the scratch parts with observations the primary color.
o Keeping working area safety & clean during installation.
o Apply insulation resistance test for internal wiring and bus bar, if any.
o Caution: Do not carry out insulation resistance test on the control circuit, CT and PT
129
CABLE LAYING:-
o Excavation trench and / or conduits according to dimensions are appropriate based on the
approved drawings and the number of cables to be lay.
o The intersection of roads is made according to duct bank drawings using U.P.V.C pipes.
o The trench route is according to drawings.
o Ensure that the trench is clear from stones and the lower sand layer thickness is according
to the designs.
o Put the cables drums in suitable place and ready to be used.
o The cables are lifted on cable drum lifting jack.
o Cables pulling are being done using a suitable number of labors.
o Cables are laid in correct configuration as per the drawings.
o In case of shortage in medium voltage cable length make a joint with enough spare length
and indicate its location in as built drawing.
o Cables is covered by suitable thickness of sand according to design.
o For medium voltage cable put continuous longitudinal bricks over cable route as per
approved drawings
o The warning tap is putting in accordance with the designs.
o Trenches are back filled completely.
o The not used excavated soil to be transferred outside the site.
o Apply continuity & insulation resistance tests for cables.
130
131
بعض الصور التوضيحية لخطوات وبنود التنفيذ من بعض المشاريع السابقة في مصر والخارج
132
133
134
135
136
137
138
139
140