Professional Documents
Culture Documents
HB Epoxy Factory Floor Paint TDS
HB Epoxy Factory Floor Paint TDS
HB Epoxy Factory Floor Paint TDS
- Easy To Clean
- 2 Part Epoxy System
- Highly Durable - Suitable for Forklift Tra c
- Surface usable again in 24 hours
- Superb Coverage Rates 17-20+ sqm /5kg
- Solvent free & Oil Tolerant
Mixed s.g: 1.6 degrees will have a slower minimum cure rate.
Full chemical resistance: 7 days @ 20°C dispersed. Please note that after mixing both components, 100% of the
material must be used in a single application and cannot be stored for later
Coverage 0.25 - 0.30 kg/m2/coat
use. Particularly for larger areas of application, pay close attention to the pot
Adhesive strength to concrete: 3.9 N/mm²
life of this product after mixing/activating. It may be optimal to have two or
Adhesive strength to steel: >12 N/mm² more people completing this job for maximum e ciency within the products
Chemical Resistance:
Excellent resistance to dilute acids and alkalis, oils. Suitable for most types of industrial spills but where speci c chemical resistance is required we
recommend a coat of Resincoat Chemically Resistant UVR Floor Paint.
General Guidance:
This Data Sheet is for general guidance purposes only and may contain information that is inappropriate for certain conditions of use. Accordingly,
all recommendations and suggestions are made without guarantee. Further information is available from our technical department. You can call us
on 0113 827 2387 for free technical advice about your project.
Floor Paints - Wall Paints - Resin Bound Driveway Kits - Concrete Repair - Magnetic LVT Flooring - Waterproo ng
Easy to use products at unbeatable prices manufactured proudly by Resincoat in the UK
Page 1 of 3
O ce: Unit 21A, Hoyle Mill Road, Kinsley, Pontefract, WF9 5JB
Call: +44 (0) 113 827 2387
E-mail: sales@resincoat.co.uk
Visit online: www.resincoat.co.uk
Date Revised: 29/04/2019
Surface Preparation
Two coats on most surfaces will produce a tough, high gloss nish. Surfaces of higher than normal porosity may require further coats.
Concrete should be a minimum of 21 days old and/or the residual moisture content shall be below 6%. Ensure that the concrete is clean and free
from dust, laitance, grease, oil, curing compound, existing paint nishes, etc. Blow holes and defective concrete shall be made good using a
proprietary repair compound, e.g. EP Mortar. A relevant Primer should be used especially with new concrete and oil stained concrete.
Blockwork should be sealed using an Epoxy Primer. Suitable mechanical treatment, such as vacuum grit - blasting, is the preferred treatment prior
to application, as this ensures a mechanical “key” for the coating. Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish
standard. All dust and grease shall be removed prior to coating application. If a delay is likely to occur between blasting and application, then it is
recommended that a coat of Steel prime be applied as holding primer to obviate ash rusting.
Application
The mixed unit should be applied immediately by roller or brush with a consistent method. Floor areas should be cross-rolled to ensure even
application and to minimise roller marks. Move down the oor and repeat the process until complete. If coating a large area, you may require a
second pair of hands. After a minimum of 14 hours and before a maximum of 24 hours, subsequent coats should be applied. A typical system would
be 1 coat of relevant Primer and 2 coats of high build. In this case after the primer has been applied, the rst coat of HB should be applied no longer
than 24 hours after the primer has cured or is dry to touch. Similarly, the 2nd coat of HB should be applied no longer than 24 hours after HB coat 1
has cured. Our HB Epoxy Resin range of paints are not UV Stable, if UV Stability is required please apply a coat of Resincoat Chemically Resistant
UVR Paint.
For more information please visit our Information Hub https://www.resincoat.co.uk/information-hub
Coverage
A 5 kg pack is su cient to coat 17 -20m² in a single coat, 2 coats provide an overall d.f.t. of 425 - 500 microns. Coverage cannot be guaranteed due
to vastly different surfaces.
Page 2 of 3
O ce: Unit 21A, Hoyle Mill Road, Kinsley, Pontefract, WF9 5JB
Call: +44 (0) 113 827 2387
E-mail: sales@resincoat.co.uk
Visit online: www.resincoat.co.uk
Date Revised: 29/04/2019
ENVIRONMENTALLY
HAZARDOUS SUBSTANCE,
ADR/ADN 3082 LIQUID, N.O.S. (LIQUID
9 III
EPOXY RESIN, ALIPHATIC
GLYCIDYL ETHER)
ENVIRONMENTALLY
HAZARDOUS SUBSTANCE,
ICAO/IATA 3082 LIQUID, N.O.S. (LIQUID 9 III
EPOXY RESIN, ALIPHATIC
GLYCIDYL ETHER)
ENVIRONMENTALLY
HAZARDOUS SUBSTANCE,
IMO/IMDG 3082 LIQUID, N.O.S. (LIQUID 9 III
EPOXY RESIN, ALIPHATIC
GLYCIDYL ETHER)
Page 3 of 3