Professional Documents
Culture Documents
04_jsa_installation_cpvc Nonmetalic Pipe_modification Works at Al Khaleej House @Abqaiq.
04_jsa_installation_cpvc Nonmetalic Pipe_modification Works at Al Khaleej House @Abqaiq.
04_jsa_installation_cpvc Nonmetalic Pipe_modification Works at Al Khaleej House @Abqaiq.
REFERENCES:
Work Permit System GI-2.100
SA-CSM Hand Tools and Power Tools under Section 11.4 Requirements for Specific Types of Hand Tools
Lockout and Use of Hold tags process G.I 6.012
SAFETY EQUIPMENT REQUIRED: Safety Hat, Safety Shoes, Safety Gloves, Safety Glasses, Ear Plugs; pad lock & hold tag; caution/ warning tape
Note: AdequateandspecialPPEmustalsobeconsideredforthistask
JOB
STEP
NO. SEQUENCE OF BASIC JOB STEPS POTENTIAL HAZARDS REQUIRED HAZARD CONTROLS/SAFE WORK PROCEDURES
Damage Power Tools & Hand Safety Officer / Supervisor /Foreman should inspect tools on
Tools regular basis to avoid any incident. And Damage tools should
be removed from the site.
Installation of Firefighting Pipes and Slippery Floor. Foreman/ Supervisor/Worker need to inspect the floor before
sprinkler using portable Ladder Damage Ladder. start working on ladder.
Fall form height. Safety Officer /Supervisor should inspect the ladder weather it
Falling objects. is in good condition.
Over loading. Incompetent worker should not work on the ladder.
Access & egress Worker should not lift any slippery or Heavy Material which
has potential to fall.
Worker should not keep any material on the steps of the
ladder.
Closing out of work Trash can shall be provided for garbage, trash and unwanted
materials. Trash shall remove from waste bin on a daily basis.
Discarded unnecessary things.
Poor Housekeeping Keep tidy and clean area daily.
Use dump truck to transport debris material to Saudi Aramco
designated dumpsite...
USE OF POWER TOOLS
Use of 4” Angle Grinder Machine (Only worker/s trained to use the grinder machine shall be allowed to operate the machine.)
a. Check cord integrity. Hand cut from cut wires.. Wear leather gloves.
Check conditions of grinding wheel and appropriate
b. (None foreseen)
RPM
c. Check grinding wheel tightness. Hand injury from inadvertent starting Do not plug in the machine until inspection is
d. Verify the guard is tight and appropriate for the job. Foot injury from dropping the tool Rest the tool on the bench. Wear steel-toed shoes.
e. Verify the appropriate handle location. Foot injury from dropping the tool (See controls for Task d.)
Inspect trigger for physical damage and proper
f. (None foreseen)
operation.
Make sure the materials being ground are Injuries associated with the work propelled 1. Verify the work is adequately secured by trying to
adequately secured and positioned correctly. by the grinder and/or landing on you dislodge it with a gloved hand (the work weight may
g. secure it enough).
2. Wear steel-toed shoes.
h. Plug-in the grinder. Eye and skin damage from projectiles. Check the trigger switch to insure it is off.
Eye injuries from projectiles and sparks Wear safety glasses/goggles and a face shield.
i. Begin grinding. Wear leather gloves, long sleeved shirt, long pants,
Skin damage from sparks and projectiles
or leather welding guards.
Accidental starts leading to drilled pants or Always remove bit after task and consider removing
leg. battery pack. Do not carry drill with your finger on
a. Carrying/handling of power drill
the trigger. Keep switch in locked or off position
when transporting or switching batteries.
Excessive force and vibration 1. Use both handles to provide power grip
d. Using hammer mode
Excessive noise 2. wear ear protection in addition to goggles
Activity:
Date:
ATTENDANCE SHEET
I DO HEREBY DECLARE THAT THE JOB SAFETY ANALYSIS WAS EXPLAINED TO ME AND I FULLY UNDERSTAND.
10
11
12
13
14
15