SECTION A Answer all questions. 1. ___________ are good conductors of heat and electricity.(a)Metal(b)Plastic(c)Wood(d)Rubbers 2. Water closet is a product of ____________.(a) plastics(b) rubber(c) ceramics(d) wood 3. French curves help to draw different ____________.(a) curves(b) lines(c) circles(d) dots 4. Oil/water spillage on the floor causes ____________ in our homes.(a) celebrations(b) party(c) accident(d) happiness 5. Grasses and leaves are also used in building construction.(a) True(b) False(c) No idea. (d) All of the above 6. All are cutting tools (metals) except ____________.(a) Spanner(b) Files(c) Chisels(d) Saws 7. ____________ crossing is an area on the road with broadwhite stripes.(a) Zebra(b) Lion(c) Tiger(d) Dog 8. Bricklaying is a technology relation occupation.(a) Yes(b) No(c) No idea(d) All of the above 9. ____________ are the plastics that we cannot soften to liquidby heating.(a) Thermocool. (b) Thermo(c) Thermoset(d) Thermoplastic 10. _________ is not a type of hammer.(a) Cross – peen(b) Cledge – hammer(c) Blocking head (d) Ball peen 11. ____________ is not a type of calipers.(a) Inside caliper(b)Odd leg caliper(c) Divider(d) K – leg caliper 12. ____________ circuit is an electrical circuit. (a) Parallel(b) Transverse(c) Direct(d) Indirect 13. Driving tools include all except ____________.(a) Hammer(b) Pliers(c) Mallet(d) Screw 14. All are not curved cutting saws except ____________.(a) Coping saw(b) Rip saw(c) Cross–cut saw(d) Dovetail saw 15. Spanners are ____________ tools.(a) driving(b) cutting(c) boring(d) marking out 16. Punch is a ____________ tool.(a) marking out(b) driving(c) cutting(d) boring 17. ____________ hammer has one flat face and one roundedface.(a) Cross – peen(b) Ball –peen(c) Claw(d) Blocking head 18. ____________ is used for drawing small features such as circles, squares, symbols etc.(a) Template(b) French curve(c) Set square(d) Protractor 19. All are building materials except ____________.(a) metals(b) paper(c) rubber(d) plastic 20. ____________ pencils include B, 2B, 3B, up to 8B.(a) Soft(b) Hard(c) Liquid(d) Gas 21. The process of providing a quick representation of an object through drawing without the aid of drawing instruments is ------ (A) Left hand sketching(B) Right hand sketching(C) Constructions(D) Freehand sketching 22. Where is the title-block located on the drawing sheet?(A) Upper right corner(B) Upper right hand corner(C) Bottom right hand corner(D) Bottom left corner 23. Which of these is a type of drawing board.(A) Small size(B) Quarter size(C) Full Imperial size(D) Medium size 24. A protractor is used for measuring ------(A) Circles(B) Curves(C) Angles(D) Lines 25. Compass is used to draw ------(A) Circles(B) Straight lines(C) Inclined lines(D) Curves 26. In the workshop, accidents are caused by one of the following:(A) Carelessness(B)Good observation(C) Good working habits(D) Good rules 27. All of these can cause fire outbreak except ;(A) Chemicals(B) Naked flames(C) Fire extinguisher(D) Electric spark 28. An unexpected event which can cause harm or injury in the workshop is called(A) Road accident(B) Workshop accident(C) Safety(D) Failure 29. ATM used in banks for financial transactions is referred to as;(A) Automating Teller Mathods(B) Automated Teller Medicine(C) Automation Teller Machining(D) Automated Teller Machine 30. Shiny or good lustre property is often associated with --------(A)Woods(B)Plastics(C)Ceramics(D) Metals 31. The type of plastics that can be easily softened and remoulded is called ---------(A)Thermolatex(B) Thermoplastic(C) Synthetic(D) Thermoset 32. What is the function of a try square?(A) Marking out right angles(B) Measuring lengths(C) Leveling surfaces(D) Measuring angles 33. Which tool is used to measure the thickness of materials?(A) Feeler gauge(B) Bevel gauge(C)Vernier caliper(D) Protracto 34. Which tool is used to mark a line parallel to an edge?(A) Scriber(B) Marking gauge(C) Dividers(D) Sliding bevel 35. Which tool is used to mark circles and arcs?(A) Bevel gauge(B) Ruler(C) Square(D) Compass 36. What is the purpose of a marking knife?(A) Boring holes(B) Marking lines on wood(C) Cutting wood(D) Measuring lengths 37. Which tool is used to strike or drive nails into wood?(A) Hammer(B) Pliers(C) Screwdriver(D) Chise 38. Which tool is used for both driving and removing screws?(A) Screwdriver(B) Pliers(C) Allen key(D) Wrench 39. What is the function of a mallet?(A) Cutting wood(B) Hammering without damaging the work surface(C) Drilling holes(D) Holding materials in place 40. Which tool is used to make round holes in wood?(A) Screwdriver(B) Auger bit(C) Chisel(D) Hammer 41. What is the purpose of a brace and bit?(A) Boring holes(B) Marking out right angles (C)Holding workpieces in place(D) Measuring angles 42. Which tool is used to enlarge an existing hole?(A) Screwdriver(B) Reamer(C) File(D) Mallet 43. What is the function of a bench vise?(A) Measuring angles(B) Holding workpieces securely (C) Boring holes(D) Cutting wood 44. Which device is used to hold a workpiece at a specific angle?(A) V-block(B) Compass(C) Clamp(D) Mallet 45. What is the purpose of a sawhorse?(A) Measuring lengths(B) Cutting wood(C) Supporting workpieces(D) Boring holes 46. Which tool is used to cut curves in wood?(A) Saw(B) Plane(C) File(D) Chisel 47. What is the function of a coping saw?(A) Boring holes(B) Cutting straight lines(C) Cutting curves and intricate shapes(D) Drilling holes 48. What is the definition of work in the context of physics?(A) The transfer of energy from one object to another(B) The speed at which an object moves(C) The amount of force applied to an object(D)The displacement of an object due to a force acting on it 49. Which of the following is a renewable source of energy?(A) Natural gas(B) Coal(C) Solar power(D) Petroleum 50. What is the SI unit of energy?(A) Watt(B) Ohm(C) Volt(D) Joule 51. Gloves are generally used for ___________protection (A) hand( B) eye (C) leg (D)hair 52. Rocks which contain metals are called __________ (A) iron (B) wood (C)plastic (D) ceramic 53.Aluminum is a _________(A) wood (B) metal (C) Plastic (D) ceramic 54._______are made from chemicals we get from crude oil (A) wood (B) glass (C) plastic (D) metal 55. Which of the following is not used in making glass? ( A) sand (B)lime (C) potash (D) clay 56.Event occurring by chance which result in injury to people or damage of property is known as (A)workshop (B)action (C)accident (D)condition . 57. Ferrous metals contain_______ (A)copper (B)iron (C) zinc (D)tin 58. The following are properties of glass except ____ (A) brittleness (B)resistance c. corrosion c. elasticity d. transparency 59. Synthetic rubber is obtained from (A) ore (B) plant (C) petroleum (D)palm oil 60. One of these is a ferrous metal (A) steel (B) brass (C)bronze( D)silver Section B, Theory Instructions: Answer all questions 1a. Define the following: Reflection Conservation 1b. Defined board practices? 2a. Explain the following Horizontal lines Vertical lines Inclined lines 2b. List and explain types of wood work machine 2b. Explained the following: Marking out tools Driving tools Boring tools Cutting tools 3a. Give 4 maintenance of wood work hand tools 3b. What is wood work machine? 4a. List types of maintenance? 4b. What is maintenance?