Professional Documents
Culture Documents
loop expansion module 4007-9803
loop expansion module 4007-9803
loop expansion module 4007-9803
Cautions and READ AND SAVE THESE INSTRUCTIONS- Follow the instructions in this installation manual. These
instructions must be followed to avoid damage to this product and associated equipment. Product operation
Warnings and reliability depend upon proper installation.
DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED- Upon unpacking
your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent,
immediately file a claim with the carrier and notify an authorized Simplex product supplier.
ELECTRICAL HAZARD - Disconnect electrical field power when making any internal adjustments or
repairs. All repairs should be performed by a representative or authorized agent of your local Simplex product
supplier.
Introduction The 4007-9803 IDNet+ Loop Expansion Card allows the operator to add one loop to an existing
IDNet+ circuit. Adding this card has the following advantages:
• Channel isolation (allows the rest of the loops to function normally even if one loop is in
default)
• Dedicated Class A wiring
• 75 additional points per card (the power supply offers 100 points)
Compatibility The 4007-9803 card is compatible with the 4007ES (for addressable notification and initiating
devices) and the 4007ES Hybrid (for non-addressable notification and addressable initiating
devices) panels*.
* From this point on, the 4007ES and the 4007ES Hybrid will be referred to as 4007ES.
Card Overview Refer to Figure 1 for the 4007-9803 card main components.
B+ B- A+ A-
IDNet+ Expansion Loop Card
Jumpers
1
2
B B
A A
Connectors
(on the reverse side)
Figure 1. Card Overview
© 2014-2016 Tyco Fire Protection Products. All rights reserved. All specifications and other information shown were current as of document 579-1106
revision date and are subject to change without notice.
Rev. B
TYCO, SIMPLEX, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited.
4007-9803 IDNET+ Loop Expansion Module
Installation
Mounting the The 4007-9803 card is installed on the 4007ES Hybrid NAC power supply or on the 4007ES
4007-9803 Card IDNAC power supply cards.
! WARNING: Make sure that all power is disconnected before starting the installation.
Standoffs A B
C D
#6-32 Screws
B+ B- A+ A-
B+ B- A+ A-
IDNet+ Expansion Loop Card
1
2
B B B B
A A A A
IDnet+ Loop
Expansion Card
Jumper
Configuration
1
2
1
2
B B
A A
2
4007-9803 IDNET+ Loop Expansion Module
Wiring
Wiring
To connect the 4007-9803 card to devices as Class A circuit:
Note: Shielded wire is not recommended. If shielded wires are present, cut and tape off the shield at each end
in the panel to prevent it from coming in contact with other components. Metallic continuity of the shield
must be maintained and insulated throughout the entire length of the cable.
1. Route wiring from Terminals B+, B-
18 to 12 AWG
on TB1 of the IDNet+ expansion loop
(0.82 to 3.31 mm2)
card to the appropriate inputs on the
first IDNet device.
2. Route wiring from the first device to IDNet
the next as in/out as shown in the Device
diagram. Repeat for each device,
maintaining polarity of wire.
3. Route wiring from the last device to
the 4007ES module Secondary
Terminals (A+, A-) on TB1 of the B+ B- A+ A-
IDNet+ expansion loop card.
4. Ensure that circuit jumpers are
IDNet
configured for Class A operation (refer
to jumper configuration section).
IDNet
Device
1 3
B+ B
B+, B- For Class B wiring
B+ B- A+ A-
Terminals only, up to 4 parallel
2 4 wiring “T” taps may be
IDNet+ Expansion
B+ B- A+ A-
3
Specifications
Specifications
Environmental Specifications:
Electrical Specifications:
Remote Device LED The IDNet+ expansion loop card tracks which remote device LEDs (if
Control equipped) should be on and can activate up to 20 LEDs at one time.
579-1106
R
Rev. B