Professional Documents
Culture Documents
AS_111196_SR-1000_SR-2000_SR-5000_CM_683US_KA_US_2040_2
AS_111196_SR-1000_SR-2000_SR-5000_CM_683US_KA_US_2040_2
A u t o - I D Te c h n i c a l G u i d e
SR-5000/2000/1000 SERIES
MITSUBISHI iQ-F FX5 SERIES
This manual explains how to connect the SR-5000/2000/1000 Series and MITSUBISHI iQ-F FX5 Series CPU
with a built-in Ethernet port via Ethernet-PLC link communication.
SR-5000/2000/1000 SERIES
MITSUBISHI iQ-F FX5 SERIES
Chapter
CONFIGURING KEYENCE CODE READER
TABLE OF CONTENTS 3 SR-5000/2000/1000 SERIES SETTINGS
Chapter 1 EQUIPMENT USED Use the AutoID Network Navigator to configure the communication
settings for the SR-5000/2000/1000 Series.
Chapter 2 CONNECTION METHOD
Chapter 3
1
CONFIGURING KEYENCE CODE READER Use a USB Cable to connect the PC and
SR-5000/2000/1000 SERIES SETTINGS
SR-5000/2000/1000 Series.
Chapter 4 CONFIGURING MITSUBISHI PLC FX5UC SERIES
SETTINGS PC
SR-5000/2000/1000 Series (AutoID Network Navigator)
Chapter 5 CREATING/SENDING LADDER PROGRAMS
Chapter 6 EXECUTING LADDER PROGRAMS AND MONITORING
THE READ DATA
Chapter
2
CPU unit Code reader
FX5UC SR-5000/2000/1000 Series Start up AutoID Network Navigator.
SR-5000/2000/1000
PC
HUB
FX5UC
2
SR-5000/2000/1000 SERIES
MITSUBISHI iQ-F FX5 SERIES
4
Chapter
Select the "Start the setup wizard" tab and configure CONFIGURING MITSUBISHI PLC
settings as shown below. 4 FX5UC SERIES SETTINGS
Configure the FX5U Series settings using GX works3.
SR-5000/2000/1000
PC
HUB
FX5UC
3
SR-5000/2000/1000 SERIES
MITSUBISHI iQ-F FX5 SERIES
3 Create a new project in GX-Works3. 6 Set the "Detailed Setting" for the "External Device
Configuration".
Select "Project" "New" from the menu. Drag "SLMP Connection Module" to the location indicated below.
Select the Series and Type.
Drag
[Communication settings]
Setting item Setting
Series FX5CPU
Type FX5U
Program Language Ladder
Click
Click
4
SR-5000/2000/1000 SERIES
MITSUBISHI iQ-F FX5 SERIES
2
Chapter
CREATING/SENDING LADDER
5 PROGRAMS
Sending ladder programs.
There are two data writing processing methods when using PLC link.
A: Real-time processing
Read data using a simple ladder program
B: Sequential processing
Select "Online" "Write to PLC..." from the menu tab.
Read data using handshake processing
B: Sequential processing
Explanation
The data write processing method can be selected from leading
address +01 (Y401) of the control area. If F0 is ON, Y401 becomes 0
and real-time processing is used. If F1 is ON, Y401 becomes 1 and
sequential processing is used.
When sequential processing is selected, data is only obtained from the
SR-5000/2000/1000 when the Y402 write permission is 1. If the Y402
write permission is 0, the read data is held in the SR-5000/2000/1000
send buffer. Restart the PLC.
* The X/Y addresses for the SR-5000/2000/1000 are hexadecimal. The X/Y
addresses for the FX5U are octal.
Therefore an address that has been converted to octal is used. * The sent program will not be applied unless the PLC is restarted.
Reading is executed
while F2 is ON
Explanation
While F2 is ON, the PLC timing area changes to 1 and reading is
executed.
When this happens the 50 words of the previous read results are
erased at 0.
The read data is stored from the leading address +04 (1004) of the
data area onward.
5
SR-5000/2000/1000 SERIES
MITSUBISHI iQ-F FX5 SERIES
* The sent program will not be applied unless the PLC is restarted.
Double click
When the data is read correctly, the contents of the read data will be
displayed as shown below.
Sample code
Enter the real-time processing command "F0" into the device name,
and turn "F0" on.
Double click
6
Copyright (c) 2017 KEYENCE CORPORATION. All rights reserved. 193114US 2040-2 683US Printed in Japan