Professional Documents
Culture Documents
20230404160328_1220
20230404160328_1220
20230404160328_1220
FRONT FOGLIGHT
Accessory Name Parts Number Application Model Issue Date Publication No. FRT
FRONT FOG ATTACHMENT 08V70-MLC-D00
XL750 2023.1 MII 0.9 H
FRONT FOGLIGHT 08V73-MKS-E00
Introduction
ALL INFORMATION, ILLUSTRATIONS, DIRECTIONS AND SPECIFICATIONS INCLUDED IN THIS PUBLICATION ARE BASED
ON THE LATEST PRODUCT INFORMATION AVAILABLE AT THE TIME OF APPROVAL FOR PRINTING. Honda Motor Co., Ltd.
RESERVES THE RIGHT TO MAKE CHANGES AT ANY TIME WITHOUT NOTICE AND WITHOUT INCURRING ANY
OBLIGATION WHATSOEVER. NO PART OF THIS PUBLICATION MAY BE REPRODUCED WITHOUT WRITTEN PERMISSION.
THIS MANUAL IS WRITTEN FOR PERSONS WHO HAVE ACQUIRED BASIC KNOWLEDGE OF MAINTENANCE ON Honda
MOTORCYCLES, MOTOR SCOOTERS OR ATVS.
Honda Dealer:
Please give a copy of these instructions to your customer.
Customer:
Because it requires specialized knowledge and special tools and equipment, it is recommended to install it at a dealer with qualified
automobile maintenance.
INFORMATION
• To prevent burns, allow the engine, exhaust system, radiator, etc., to cool before installing the accessory.
• Reinstall the removed parts on the motorcycle and make sure that the wires and harnesses are not pinched.
• Disconnect the negative (-) cable from the battery before installing this accessory.
• Trim the excess ends off the wire ties after attaching them to the wire harnesses. Do not allow the cut part of the wire tie to
interfere with another harness or brake hose.
• After reconnecting the battery, refer to the motorcycle Owner’s Manual and set the meter.
• After this accessory installation, check the lights (e.g. right/left turn signal lights and brake lights) for proper operation.
• Setting is necessary after installing this accessory.
(20)
(21)
(7)
<FRONT FOGLIGHT>
Component No. Parts Name Qty Parts No.
(22) Front foglight 2 -
(22)
(24)
(27) (30)
(29)
(31)
(25)
<GUARD ATTACHMENT>
Component No. Parts Name Qty Parts No.
(34) Right guard bracket 1 -
(35) Left guard bracket 1 -
(34) (35) (36) 10 x 75 mm flange bolt 4 90166-GHB-780
(36)
TORQUE INFORMATION
Refer to the Service Manual for the torque values including standard torque of the removed parts. ( )
INSTALLATION IMAGE
210 ± 5 mm 210 ± 5 mm
55 mm 55 mm
270 ± 5 mm 310 ± 5 mm
100 mm 130 mm
(20) (20)
Wind the electrical tape
for 2-3 turns. Wind the electrical tape
for 2-3 turns.
<LEFT SIDE>
(22)
(6)
(13)
(14)
(12)
(5)
(6)
(5) (5)
HOLE
(6)
(20)
MARK
FRONT FOGLIGHT
HARNESS
7. Install as shown.
<LEFT SIDE>
(2)
(15)
(2)
(6)
<REAR SIDE>
(7)
TAB
(17)
(7)
FRONT FOGLIGHT
HARNESS
(19)
(8)
(17)
12. Refer to the steps 2 through 4 of the instruction manual for the front side pipe, install the front side pipe.
<LEFT SIDE>
ASSEMBLED
FRONT FOGLIGHT
(32)
<LEFT SIDE>
MOTORCYCLE'S
HARNESS BOOTS
Set the wire tie in front of the hook as shown.
DUMMY
CONNECTOR
<RIGHT SIDE> TAPE Set the wire tie in front of the hook as shown.
Remove.
HOOK (20)
MOTORCYCLE'S
HARNESS BOOTS
(22)
DUMMY
CONNECTOR
16. Refer to the Service Manual for motorcycle, install the side cowls of the motorcycle parts.
(31)
ENGINE GUARD
(24)
(33)
(24)
(26)
(33)
(25) (32)
36 N·m
20. Check the foglight, headlight, and the other lights for proper operation.
SEL UP switch:
Move to the upper side menu item.
6. Turn the ignition switch OFF and remove the SCS short connector.
CUT-OFF LINE
MOUNTING
HEIGHT of
FOGLIGHT
MOUNTING
HEIGHT of
FOGLIGHT
5m