Professional Documents
Culture Documents
MANUAL ACTUADOR ASIENTO
MANUAL ACTUADOR ASIENTO
cPD93-700-0s3-00
FOR
PROPRIETARY NOTICE
This docr-unent is the property of Crane Aerospace & Electronics and contains
proprietary information. including trade secrets, and shall not be copied or
reproduced, in whole or in part. divulged or used for design or manufacture ri,ithout
specific written permission from Crane Aerospace & Electronics. The recipient, by
the acceptance, custody, use or retention of this document, agrees to the foregoing
and agrees to maintain the contents in confldence.
1.1
1.2
2
2.1
4
4.1
4.2
4.3
4.4
4.5
5
TABLE OF FIGURES
Page
Figure 1 -Calibration Mode Entrance Sequence .........2
Crane Aerospace - Proprietary. Use or disclosure of the information contained herein is subject to the restrictions on the cover page.
Page iii
CPD93-700-053-00, Revision -
1 SCOPE
This Calibration Procedure Document describes the steps required to calibrate mcX Seat
Actuation Control Systems (SACS) that are installed in the BE Aerospace / COPA Airlines
8737, Business class seats.
1.2 Effectivity
2 APPLICABLE DOCUMENTS
The following documents will form a part of this document. The latest issue will be used for
reference unless a specific revision is called out.
Crane Aerospace - Proprietary. Use or dlsc/osure of the information contained herein is subject to the restrictions on the cover page.
Page 1
CPD93-700-053-00, Revision -
Seat calibration must be performed when a Recline (PN: 93-2801-01-01)and/or Legrest (PN:
93-2108-01-02) SAM is newly installed or replaced on the seat.
Perform the following steps every time an actuator is installed in the system. Step 1) ensures
that the new LRU is cross-loaded by the software configuration module. Step 2) mechanically
aligns the potentiometer, thereby normalizing seat measurement.
4.2.1 Press the following buttons on the Main PCU within 1 second of each other in the order
shown to enter Calibration mode as shown in Figure 1.
1- TTL
2- Lumbar +
3- Recline Deploy
*tH Gruphir
Note: PCU backlight will turn on and off every 500ms upon entering calibration mode.
After performing steps shown in Section 4.2, follow the steps below to calibrate the seat:
Crane Aerospace - Proprietary. Use or dlsc/osu re of the information contained herein is subject to the restrictions on the cover page.
Page 2
CPD93-700-053-00, Revision -
4.3.1 Using the mechanical override levers, manually move the seat to the upright position in the
followinq s,equence: Recline Legrest within 60 seconds of entering CAL mode and press the
rl-I'')
t..J'l
"TrL" pJl button.
Note: PCU backlight will stay illuminated for 5 seconds and then it will return to turning on
and off every 500ms.
4.3.2 Using the mechanical override levers, manually move the seat to the fully flat position in the
;M
following sequence: Recline; Legrest within G0 seconds and press the "Bed" 1Wfl) button
Note: PCU backlight will turn on and off every 250ms after capturing second calibration point.
The system shall exit calibration mode after a time-out period of 60 seconds after the last
button was pressed and PCU backlight will return to the state prior to entering calibration
mode.
After calibration process is complete, follow steps below to ensure calibration process has
been performed successfully.
ffi
4.5.1 Press the "TTL" 1KWt, button on the PCU and verify that the seat moves to the calibrated
TTL position.
r'H
4.5.2 Press the "Bed" ([@J) button on the PCU and verify that the seat moves to the calibrated
Bed position.
Note: Seat calibration must be repeated if seat motion does not occur as desired.
Crane Aerospace - Proprietary. Use or disc/osu re of the information contained herein is subject to the restrictions on the cover page.
Page 3
CPD93-700-053-00, Revision -
5 PRODUCT SUPPORT
For technical information, contact the Product Support Representative per the following.
P.O. Box:7722
Burbank, CA 91510-7722
U.S.A.
Telephone: +1-818-526-2600
Fax: +1-818-842-6117
E-mail: info@craneae.com