Professional Documents
Culture Documents
ASTM B564-2018
ASTM B564-2018
for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: B564 − 18
中
国
Standard Specification for
Nickel Alloy Forgings1
电
This standard is issued under the fixed designation B564; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
--`,``````,,,`,`,,``,,````,````-`-`,,`,,`,`,,`---
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
建
This standard has been approved for use by agencies of the U.S. Department of Defense.
集
1. Scope* 1.2 The values stated in inch-pound units are to be regarded
2
1.1 This specification covers forgings of: as standard. The values given in parentheses are mathematical
团
conversions to SI units that are provided for information only
Alloy Type UNS Number(s)
Fe-Ni-Cr-Mo-N N08367 and are not considered standard.
Low-carbon Cr-Ni-Fe-N R20033 1.3 This standard does not purport to address all of the
华
Low-carbon Ni-Cr-Mo N06035, N06058, N06059, N06044
Low-carbon Ni-Cr-Mo-Cu N06200 safety concerns, if any, associated with its use. It is the
Low-carbon Ni-Cr-Mo-W N06686 responsibility of the user of this standard to become familiar
Low-carbon Ni-Fe-Cr-Mo-Cu N08031, N08034 with all hazards including those identified in the appropriate
东
Low-carbon Ni-Mo-Cr N10276, N06022, N10362
Low-carbon Ni-Mo-Cr-Ta N06210 Safety Data Sheet (SDS) for this product/material as provided
Ni N02200 by the manufacturer, to establish appropriate safety, health,
Ni-Co-Cr-Si N12160
勘
and environmental practices, and determine the applicability
Ni-Cr-Al N06699
Ni-Cr-Co-Mo N06617 of regulatory limitations prior to use.
Ni-Cr-Fe N06600, N06603, N06690 1.4 This international standard was developed in accor-
测
Ni-Cr-Fe-Al N06025 dance with internationally recognized principles on standard-
Ni-Cr-Fe-Si N06045
Ni-Cr-Mo-Nb N06625 ization established in the Decision on Principles for the
Ni-Cr-Mo-Si N06219 Development of International Standards, Guides and Recom-
设
Ni-Cr-Mo-W N06110
mendations issued by the World Trade Organization Technical
Ni-Cr-W-Mo N06230
Ni-Cu N04400 Barriers to Trade (TBT) Committee.
Ni-Fe-Cr N08120, N08800, N08810, N08811
计
Ni-Fe-Cr-Mo-Cu N08825 2. Referenced Documents
Ni-Fe-Cr-W N06674
Ni-Mo N10665, N10675, N10629 2.1 ASTM Standards:3
研
Ni-Mo-Cr-Fe N10242, N10624 B880 Specification for General Requirements for Chemical
1.1.1 The nickel-iron-chromium alloys are UNS N08120, Check Analysis Limits for Nickel, Nickel Alloys and
UNS N08800, UNS N08810, and UNS N08811. Alloy UNS Cobalt Alloys
究
N08800 is normally employed in service temperatures up to E8/E8M Test Methods for Tension Testing of Metallic Ma-
and including 1100°F (593°C). Alloys UNS N08810, N08120, terials
and UNS N08811 are normally employed in service tempera- E29 Practice for Using Significant Digits in Test Data to
院
tures above 1100°F (593°C) where resistance to creep and Determine Conformance with Specifications
rupture is required, and are annealed to develop controlled E76 Test Methods for Chemical Analysis of Nickel-Copper
grain size for optimum properties in this temperature range. Alloys (Withdrawn 2003)4
有
1.1.2 Nickel-iron-chromium-tungsten alloy UNS N06674 is E112 Test Methods for Determining Average Grain Size
normally employed in service temperatures above 1100°F E350 Test Methods for Chemical Analysis of Carbon Steel,
限
(593°C) where resistance to creep and rupture is required, and Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and
is annealed to develop optimum properties in this temperature Wrought Iron
range. E1473 Test Methods for Chemical Analysis of Nickel, Co-
公
balt and High-Temperature Alloys
1
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
司
3
B02.07 on Refined Nickel and Cobalt and Their Alloys. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 1, 2018. Published November 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1972. Last previous edition approved in 2017 as B564 – 17a. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/B0564-18. the ASTM website.
2 4
For ASME Boiler and Pressure Vessel Code applications see related Specifi- The last approved version of this historical standard is referenced on
cation SB-564 in Section II of that Code. www.astm.org.
6.1 Dimensions and tolerances shall be as specified on the 11.2 The measurement of average grain size may be carried
out by the planimetric method, the comparison method, or the
有
applicable forging sketch or drawing.
intercept method described in Test Methods E112. In case of
7. Workmanship, Finish, and Appearance dispute, the “referee” method for determining average grain
限
7.1 The material shall be uniform in quality and condition, size shall be the planimetric method.
sound, and free of injurious imperfections. 11.3 For purposes of determining compliance with the
specified limits for requirements of the properties listed in the
公
8. Sampling following table, an observed value, or a calculated value, shall
8.1 Lot Definition: be rounded as indicated as follows, in accordance with the
8.1.1 A lot for chemical analysis shall consist of one heat. rounding method of Practice E29:
司
8.1.2 A lot for mechanical properties and grain size testing Test
Rounded Unit for Observed or
shall consist of all material from the same heat, size, finish, Calculated Value
Chemical composition nearest unit in the last right-hand place
condition, and processed at one time. of figures of the specified limit
Tensile strength, yield strength nearest 1000 psi (6.9 MPa)
Elongation nearest 1 %
5
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Grain size:
Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:// 0.0024 in. (0.060 mm) or larger nearest multiple of 0.0002 in. (0.005 mm)
www.dodssp.daps.mil. less than 0.0024 in. (0.060 mm) nearest multiple of 0.0001 in. (0.002 mm)
测
Cobalt ... ... 2.5 ... 1.00 ... ... 0.3 0.3 ...
Vanadium ... ... 0.35 ... 0.20 ... ... ... ... ...
Nitrogen ... ... ... ... ... ... ... 0.02 - 0.15 ... ...
Boron ... ... ... ... ... ... ... ... ... ...
设
Lanthanum ... ... ... ... ... ... ... ... ... ...
Aluminum + ... ... ... ... ... ... ... ... ... ...
Cobalt 2.0 1.0 1.0 5.0 ... 10.0 min– ... ... ...
测
15.0
Vanadium ... 0.35 ... ... ... ... ... ... ...
Nitrogen ... ... ... ... ... ... ... ... 0.02
设
Boron ... ... ... 0.015 ... 0.006 ... ... 0.0005-
0.006
--`,``````,,,`,`,,``,,````,````-`-`,,`,,`,`,,`---
研
(Nb)
Tantalum ... 1.5-2.2 ... ... ... ... ... ... ...
Molybdenum 15.0–17.0 ... ... 6.0-7.0 6.0–7.0 2.50 6.00–7.00 ... ... ... 2.5–3.5
B564 − 18
Phosphorus 0.04 ... 0.02 0.020 0.020 0.040 0.040 ... ... ... ...
测
Tungsten 3.0–4.4 ... ... ... ... 2.50 ... ... ... ... ...
Cobalt ... ... ... ... ... 3.0 ... ... ... ... ...
Vanadium ... ... ... ... ... ... ... ... ... ... ...
设
Nitrogen ... ... 0.05 0.15-0.25 0.10–0.25 0.15–0.30 0.18–0.25 ... ... ... ...
Boron ... ... 0.008 ... ... 0.010 ... ... ... ... ...
Nickel + ... ... ... ... ... ... ... ... ... ... ...
Molybdenum
研
Columbium ... ... 0.50 ... ... ... ... ... ... ... ...
(Nb)
测
Cobalt 1.00 2.5 ... 1.0 2.5 1.00 3.0 27.0–33.0 ...
Vanadium ... 0.35 ... ... ... ... 0.20 ... ...
Nitrogen ... ... ... ... ... ... ... ... 0.35–0.60
Boron 0.006 ... ... ... ... ... ... ... ...
设
Lanthanum ... ... ... ... ... ... ... ... ...
Aluminum + ... ... ... ... ... ...
annealed
Nickel-chromium-tungsten-
molybdenum alloy UNS N06230, ... 110 (758) 45 (310) 40
solution annealedC
Nickel-copper alloy UNS N04400,
... 70 (483) 25 (172) 35
annealed
Nickel-iron-chromium alloys:
UNS N08120, solution annealed ... 90 (621) 40 (276) 30
UNS N08800, annealed ... 75 (517) 30 (207) 30
--`,``````,,,`,`,,``,,````,````-`-`,,`,,`,`,,`---
12. Inspection stating that material has been manufactured, tested, and in-
12.1 Inspection of the material by the purchaser shall be spected in accordance with this specification, and that the test
勘
made as agreed upon between the purchaser and the seller as results on representative samples meet specification require-
part of the purchase contract. ments. When specified in the purchase order or contract, a
report of the test results shall be furnished.
测
13. Rejection and Rehearing
13.1 Material, tested by the purchaser, that fails to conform 15. Product Marking
to the requirements of this specification may be rejected.
设
Rejection should be reported to the producer or supplier 15.1 The material shall be marked legibly with the name of
promptly and in writing. In case of dissatisfaction with the the material, this specification number, the heat number and
results of the test, the producer or supplier may make claim for condition, and such other information as may be defined in the
计
a rehearing. contract or order.
14. Certification
研
16. Keywords
14.1 When specified in the purchase order or contract, a
16.1 nickel alloy forgings
manufacturer’s certification shall be furnished to the purchaser
究
SUPPLEMENTARY REQUIREMENTS
院
The following supplementary requirements shall apply only when specified by the purchaser in the
inquiry, contract, or order, for agencies of the U.S. Government.
有
S1. Referenced Documents MIL-STD-792 Copper-Base Alloy Mill Products
限
S1.1 The following documents of the issue in effect on date
S2. Chemical Composition
of material purchase form a part of this specification to the
extent referenced herein. S2.1 UNS alloy N04400 shall conform to the composition
公
S1.1.1 Federal Standards: limits specified in Table 1 except as specified in Table S2.1
Fed. Std. No. 102 Preservation, Packaging and Packing
S3. Mechanical Properties
司
Levels
Fed. Std. No. 123 Marking for Shipment (Civil Agencies) S3.1 Mechanical property requirements for UNS alloy
Fed. Std. No. 185 Identification Marking of Copper and N04400 forgings in the hot finished and hot finished/high
Copper-Base Alloy Mill Products tensile conditions shall be as specified in Table S3.1
S1.1.2 Military Standards:
MIL-STD-129 Marking for Shipment and Storage S4. Number of Tests
S1.1.3 Military Specification: S4.1 One tensile specimen is required for each forging
MIL-C-3993 Packaging of Copper greater than 250 pounds in as shipped weight.
(1) Added new alloy UNS N06699 to Scope (Section 1). (3) Added Mechanical Property data to Table 2 for UNS
有
(2) Added chemistry data for UNS N06699 to Table 1. N06699.
Committee B02 has identified the location of selected changes to this standard since the last issue (B564–17)
限
that may impact the use of this standard. (Approved July 1, 2017.)
公
(1) Added new alloy UNS N08034 to scope (Section 1). (3) Added Mechanical property data to Table 2 for UNS
(2) Added chemistry data for UNS N08034 to Table 1. N08034.
司
--`,``````,,,`,`,,``,,````,````-`-`,,`,,`,`,,`---
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
国
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
电
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
建
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222
Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/
集
团
华
--`,``````,,,`,`,,``,,````,````-`-`,,`,,`,`,,`---
东
勘
测
设
计
研
究
院
有
限
公
司