Professional Documents
Culture Documents
ASTM A516_A516M-2017
ASTM A516_A516M-2017
for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
--`,`,``,,,,`,,,,`,,`,,,,,,,,`,`-`-`,,`,,`,`,,`---
C
Grade 60 plates 1⁄2 in. [12.5 mm] and under in thickness may have 0.85–1.20 % manganese on heat analysis, and 0.79–1.30 % manganese on product analysis.
东
TABLE 2 Tensile Requirements
勘
Grade
55 [380] 60 [415] 65 [450] 70 [485]
测
Tensile strength, ksi [MPa] 55–75 [380–515] 60–80 [415–550] 65–85 [450–585] 70–90 [485–620]
Yield strength, min,A ksi [MPa] 30 [205] 32 [220] 35 [240] 38 [260]
Elongation in 8 in. [200 mm], min, %B 23 21 19 17
Elongation in 2 in. [50 mm], min, %B 27 25 23 21
设
A
Determined by either the 0.2 % offset method or the 0.5 % extension-under-load method.
B
See Specification A20/A20M for elongation adjustment.
计
NOTE 1—For plates produced from coil and furnished without heat 5.4 If approved by the purchaser, cooling rates faster than
treatment or with stress relieving only, three test results are reported for those obtained by cooling in air are permissible for improve-
研
each qualifying coil. Additional requirements regarding plate produced
from coil are described in Specification A20/A20M. ment of the toughness, provided the plates are subsequently
tempered in the temperature range 1100 to 1300°F [595 to
3.5 If the requirements of this specification are in conflict
705°C].
究
with the requirements of Specification A20/A20M, the require-
ments of this specification shall prevail.
6. Chemical Composition
院
4. Materials and Manufacture
6.1 The steel shall conform to the chemical requirements
4.1 Steelmaking Practice—The steel shall be killed and given in Table 1 unless otherwise modified in accordance with
shall conform to the fine austenitic grain size requirement of
有
Supplementary Requirement S17, Vacuum Carbon-Deoxidized
Specification A20/A20M. Steel, in Specification A20/A20M.
5. Heat Treatment
限
7. Mechanical Properties
5.1 Plates 1.50 in. [40 mm] and under in thickness are
normally supplied in the as-rolled condition. The plates may be 7.1 Tension Test—The plates, as represented by the tension
公
ordered normalized or stress relieved, or both. test specimens, shall conform to the requirements given in
5.2 Plates over 1.50 in. [40 mm] in thickness shall be Table 2.
normalized.
司
8. Keywords
5.3 When notch-toughness tests are required on plates
1 ⁄ in. [40 mm] and under in thickness, the plates shall be
12 8.1 carbon steel; carbon steel plate; pressure containing
normalized unless otherwise specified by the purchaser. parts; pressure vessel steels; steel plates for pressure vessels
--`,`,``,,,,`,,,,`,,`,,,,,,,,`,`-`-`,,`,,`,`,,`---
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
国
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
电
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
建
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222
Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/
集
团
华
东
勘
测
设
计
研
究
院
有
--`,`,``,,,,`,,,,`,,`,,,,,,,,`,`-`-`,,`,,`,`,,`---
限
公
司