Professional Documents
Culture Documents
Frankever Soil Tester User Manual
Frankever Soil Tester User Manual
FK-3002-TRREC-N01
Ver 2.0
catalogue
Chapter 1 product introduction
1.1 Product Overview
1.2 functional features
1.3 main parameters
1.4 product selection
1.5 product selection
Chapter 2 usage
2.1 equipment list
2.2 structure description
2.3 sensor connection equipment
2.4 terminal instructions
2.4.1 quick measurement method
2.4.1 buried survey method
Chapter 3 function and operation description
3.1 key description
3.2 introduction to main interface
3.3 operating instructions
3.3.1 system setting description
3.3.2 equipment management description
3.3.3 description of viewing historical data
Chapter 4 instructions for configuration software
1
4.1 setting detection parameters
4.2 importing data
4.3 export data
4.4 clearing equipment data
Chapter 5 description of charging function
Chapter 6 precautions
Chapter 7 common faults and Solutions
2
Connectable equipment 1-4 MODBUS device combinations
communication protocol Modbus RTU protocol
working voltage DC 4.2V
Standby time More than 8h continuous
size 174*88.5*35 mm
weight 284g
3
Product size:
5
2.4.1 buried survey method
Dig the pit with diameter > 20cm vertically, insert the sensor steel needle
horizontally into the pit wall at the given depth, fill the pit tightly and stabilize it for a
period of time, and then measure and record for several days, months or even longer
6
picture name explain
Main interface: press and hold the opening sound in the
alarm state and open state. When an alarm occurs, press
and hold to eliminate the alarm sound; Short press up in
Up key
the menu interface to select setting items and add
values; Short press on the password interface to
increase the value
Main interface: long press to close the sound in the
alarm state and open state
Short press down on the menu interface to select setting
Direction down key
items and add values
Short press on the password interface to reduce the
value
Short press right on the main interface to switch the
display interfaces of different devices
Left arrow key
Short press on the menu interface to move the cursor to
the right
Short press right on the main interface to switch the
display interfaces of different devices
Direction right key
Short press on the menu interface to move the cursor to
the right
Host interface: long press to open or close the data
record, short press to enter the password interface;
Confirm key
Short press to confirm the selection in the menu
interface
Short press in the menu interface to return to the
Return key previous interface;
Any interface: long press to return to the main interface.
7
3.2 introduction to main interface
eleven Real time value Displays the actual feature values currently detected
twelve Proportion The ratio of the current measured value to the range of this sensor
8
3.3 operating instructions
1. In the shutdown state, long press the 2S confirmation key, the equipment
detects whether the buzzer is in normal use, and the equipment enters the main
interface
2. On the main page, briefly press the confirm key to enter the password
interface. The password defaults to 0000. Press the cycle key to move the cursor to
confirm, and click the confirm key to enter the menu interface. As shown in Figure 1:
图1
3.3.1 system setting description
Move the cursor to the corresponding icon and click OK to enter the setting
interface
9
3.3.2 equipment management description
Note: when multiple sensors are connected at the same time, the sensor addresses
shall not conflict, so as to avoid confusion when the configuration software views the
data curve.
10
3.3.3 description of viewing historical data
This operation can view the historical data on the device and import the data stored on
the device into the computer for viewing. Please refer to section 4.2 and 4.3 for
specific operations.
Connect the device to the computer through the USB data cable, open the
software and automatically read the device information. After editing the device
parameters, click "write device information" to write the parameters into the device.
11
It should be noted that after the modified parameter, check the modify parameter, and
then click write device information to write the parameter to the device. This function
is set to facilitate the wrong modification of other parameters when modifying
individual parameters.
12
Click data to view the stored historical data in time.
13
4.4 clearing equipment data
Click "device" in the toolbar and click "clear device stored data" in the drop-down
menu to clear the device data. After clearing, the software prompts "data cleared
successfully".
When the equipment is shut down, connect the charger to the recorder and the other
end to the AC220V AC power supply. After the detector is fully charged, the power
display is full and can be used normally.
Chapter 6 precautions
1. Prevent the machine from falling from a height or being subjected to severe
vibration.
2. Please use the recorder in strict accordance with the instructions, otherwise the test
results may be inaccurate or the product may be damaged.
14
manufacturer for repair
No response from Please contact your dealer or
Circuit failure
inserted sensor manufacturer for repair
Contact your dealer or manufacturer
Sensor failure
Inaccurate display
Replace the sensor
Long term uncalibration Please calibrate in time
The battery is completely Replace the RTC battery and reset the
discharged time
Time display error
Strong electromagnetic
Reset time
interference
When the instrument Contact your dealer or manufacturer
is tested normally Replace the sensor
Sensor failure
The interface displays
full scale
15