Professional Documents
Culture Documents
20- Wiring
20- Wiring
GENERAL PREAMBLES
1. All work and materials shall conform to the Specifications, Public Utilities Board, and
other relevant Statutory Requirements and to be approved by the S.O. Representative,
Town Council.
2. The description given for each item shall unless otherwise stated, be held to include
the use of materials, labour, equipment, tools, boom lift and vehicles, replacement and
making good, supply of fuel and all idle time, conveyance, delivery, unloading,
storing, hoisting, stools/ ladders, all labour setting, fitting, fixing in position, all
cutting and waste, return of packings, establishment charges, overheads, profit and all
forms of chain for loss and expense, labour dismantling , making good all affected
works and disposal of fittings including checking, tracing and clearing of fault (if any)
before installation and testing after installation.
3. The rate for each item for the installation/ fixing of electrical fittings shall unless
otherwise stated, deemed to include all staples, clips, screws, bolts, rawl plug ramset
brackets and other fixing accessories for the satisfactory completion of the installation
works.
4. Unless otherwise stated, all work shall be measured nett as fixed in its place.
5. If there is any disagreement between the Town Council and the term Contractor on
any of the items, the Town Council’s assessment shall be taken as final.
m - Linear metre
m2 - Square metre
m3 - Cubic metre
no. - Number
kg - Kilogram
ton - Tonne
pr - Pair
sht - Sheet
ltr - Litre
set - Complete set
job - Piece of work
8. Where trade names or manufacture’s catalogue numbers are used, the reference is
intended only as a guide to the type of article or material used. The Contractor may
use any other article or material, subject to prior approval of the S.O. Representative.
POINT WIRING
UNDERGROUND CABLES
( S' pore Cable Manufacturer, Sigma, Tai Sun, Wilson)
100 50mm diameter, UPVC Class C pipe for road crossing m 3.20
laid in trench ( trench measured separately )
101 80mm diameter, UPVC Class C pipe for road crossing m 5.60
laid in trench ( trench measured separately )
102 100mm diameter, UPVC Class C pipe for road crossing m 9.30
laid in trench ( trench measured separately )
103 150mm diameter, UPVC Class C pipe for road crossing m 20.00
laid in trench ( trench measured separately )
CONDUIT
( Barton, Maruchi, Walsall, Burns)
114 20mm diameter super high impact heavy gauge PVC m 2.70
conduit fixed to wall or ceiling complete with spacer
bas, saddles, inspection boxes / junctions / bends /
tees, elbows and joint accessories
115 25mm diameter super high impact heavy gauge PVC m 3.00
conduit fixed to wall or ceiling complete with spacer
bas, saddles, inspection boxes / junctions / bends /
tees, elbows and joint accessories
116 32mm diameter super high impact heavy gauge PVC m 4.20
conduit fixed to wall or ceiling complete with spacer
bas, saddles, inspection boxes / junctions / bends /
tees, elbows and joint accessories
117 38mm diameter super high impact heavy gauge PVC m 7.50
conduit fixed to wall or ceiling complete with spacer
bas, saddles, inspection boxes / junctions / bends /
tees, elbows and joint accessories
PVC TRUNKINGS
METAL TRUNKING
(Ekko, Sakiya, Li-Soon )
CABLE TRAY
ELECTRICAL ACCESSORIES
* Supply and fix the following accessories and fittings
fittings includidng all necessary fiixing screws and
plastic plugs
193 20 Amp double pole water heater switch c/w pilot No 14.90
lamp and white moulded surface mounting box
196 20 Amp DP metal clad switch fuse c/w HRC fuse No 89.60
( Mem, Stromberg, Simplex )
197 32 Amp DP metal clad switch fuse c/w HRC fuse No 121.90
( Mem, Stromberg, Simplex )
198 63 Amp DP metal clad switch fuse c/w HRC fuse No 250.00
( Mem, Stromberg, Simplex )
199 100 Amp DP metal clad switch fuse c/w HRC fuse No 270.70
( Mem, Stromberg, Simplex )
200 20 Amp TPN metal clad switch fuse c/w HRC fuse No 112.40
( Mem, Stromberg, Simplex )
201 32 Amp TPN metal clad switch fuse c/w HRC fuse No 150.70
( Mem, Stromberg, Simplex )
202 63 Amp TPN metal clad switch fuse c/w HRC fuse No 283.00
( Mem, Stromberg, Simplex )
203 100 Amp DP metal clad switch fuse c/w HRC fuse No 450.80
( Mem, Stromberg, Simplex )
223 Metal Clad split load consumer unit complete with No 243.00
40 Amp DP RCCB 63 Amp DP or 32 Amp DP isolator
6 x 5/20 Amp 6KA MCB (ABB, Mem, Sunlight )
224 Metal Clad split load consumer control unit complete No 275.50
with 60 Amp DP isolator 1 x 20A sp MCB, 40 Amp DP
ELCB with 7 x 5/20A 6KA sp MCB )
(ABB, Mem, Sunlight
227 100 Amp B.I connector, ' Quintela ' or other approved No 21.40
228 150 Amp B.I connector, ' Quintela ' or other approved No 32.90
229 200 Amp B.I connector, ' Quintela ' or other approved No 46.70
232 18 mm2 capacity line tape with hexagon screw and felt No 7.10
233 30 mm2 capacity line tape with hexagon screw and felt No 8.90
234 50 mm2 capacity line tape with hexagon screw and felt No 11.30
235 75 mm2 capacity line tape with hexagon screw and felt No 17.80
236 120 mm2 capacity line tape with hexagon screw and felt No 60.00
245 100 Amp HRC fuse with carrier and base No 49.00
( Mem, Legrand, Merlin Gerin, PDL )
250 100 Amp industrial bolted pattern HRC fuse link No 12.10
( Mem, English Electric, Legrand )
251 160 Amp industrial bolted pattern HRC fuse link No 13.50
( Mem, English Electric, Legrand )
252 200 Amp industrial bolted pattern HRC fuse link No 14.30
( Mem, English Electric, Legrand )
253 300 Amp industrial bolted pattern HRC fuse link No 21.50
( Mem, English Electric, Legrand )
254 400 Amp industrial bolted pattern HRC fuse link No 42.90
( Mem, English Electric, Legrand )
255 500 Amp industrial bolted pattern HRC fuse link No 51.50
( Mem, English Electric, Legrand )
256 600 Amp industrial bolted pattern HRC fuse link No 59.60
( Mem, English Electric, Legrand )
258 Single phase tap off box complete with 60 Amp 25 KA No 292.20
240V DP MCCB, 2 x 95mm2 line-tap connectors,
BI connectors, earth connector and earthing terminal
( ABB, Sunlight, Huat Heng, Soundtext )
259 Single phase tap off box complete with 2 x 60 Amp 25 KA No 373.00
240V DP MCCB, 2 x 95mm2 line-tap connectors,
BI connectors, earth connector and earthing terminal
( ABB, Sunlight, Huat Heng, Soundtext )
263 Three phase 100 Amp usfused tap-off units complete No 143.90
with 50 mm2 line-tap connectors, neutral connector
earth link as specified
( ABB, Sunlight, Huat Heng, Soundtext )
MAINWSITCHBOARD'S ACCESSORIES
308 One set 3 nos. IDMTL overcurrent relay c/w metal No 4974.80
enclosure ( excluding injection test on site and
current transformer )
326 " Horstmann " Type Y Quartz or other approved time No 175.10
switch with 150 hours battery reserve
330 Supply and fix Indoor Service Electrical Distribution Set 1693.00
Panels ( OG Box) comprising : -
4 Nos. 630 Strip Fuse Way
6 Nos. 630A Solid Link
3 Nos. 200 HRC Fuse Link
2 Nos. Cast Resin Insulator
3 Nos. 70mm2 Earth Braid c/w lugs
3 Nos. 70mm2 cable clip
1 No. 1720mm x 610mm x 350mm Metal Enclosure c/w
Panel Lock ( Sunlight, Suat Heng, Soundtrex,
Seah & Lee)
FANS
337 1.5 diameter sweep ceiling fan complete with regulator No 88.00
and teak board (KDK, National, Mitsubishi)
341 Supply and fix 500mm (20") diameter "KDK" wall No 370.00
Model H50 CK in replacement including removing of
existing wall fan
343 Supply and fix 635mm (25") diameter "KOUKYU" No. 210.00
wall fan 240V, 1400 rpm 50 Hz
Model 303 (MG) in replacement including removing
of existing wall fan
344 Rewind of fan motor coil for 400mm or 500mm diameter No 40.30
wall bracket fan
LUMINAIRES
359 Lucerne 270-G surface mounted wall light (IP54) c/w No 79.35
2 x 9W PL lamp and accessories
360 Bega 2491 wall light (IP45) c/w 1 x 26W PLC & accessories No 419.75
361 Goccia 2898 wall light c/w 2 x 9W PL lamp & gear No 98.90
384 Capacitor 7.5 / 6.5 mfd for 40W fluorescent lamps No 5.80
386 Electronic ballast for single 20W or 40W fluorescent lamp No 30.00
(PUB approved type with SISIR sticker)
405 Supply and fix halogen lamp 12V 50W / 20W No 8.00
(Osram, Philip, Thorn)
417 ' PHILIPS ' BPL 10 L23 ballast for compact fluorescent lamp No 11.10
(Ozon, Splendour, Osram, Sylvania)
418 ' PHILIPS ' TCS 058 / 118 fluorescent luminaire c/w No 91.00
1 x 18W TLD lamp, low loss ballast in HPF switch start
circuitry and opal diffuser
419 ' PHILIPS ' TCS 058 / 236 fluorescent luminaire c/w No 155.00
2 x 36W TLD lamp, low loss ballast in HPF switch start
circuitry and opal diffuser
424 ' AMCOL ' AFR /M24 /236 recessed fluorescent fittings No 77.60
c/w ATCO LEC 40 EO low losss ballasts & KSH 12 (C12)
clear flat acrylic prismatic diffusers c/w 2 x 36W tubes
425 ' AMCOL ' AFR /M22 /218 recessed fluorescent fittings No 57.40
c/w ATCO LEC 20 EO low losss ballasts & KSH 12 (C12)
clear flat acrylic prismatic diffusers c/w 2 x 18W tubes
426 'AMCOL ' C12 1200mm x 600mm clear flat prismatic No 14.80
diffuser only
429 'GEC' dd 120 flourescent luminaires and low loss ballast, No 32.00
diokon diffuser c/w 1 x 18W tube
459 100 watts GLS coiled coil tungsten incandescent lamp No 4.90
bulbs with ES caps for aircraft warning light
461 Lightcraft AGT 146 / P3-2 double c/w PLC 26W Set 590.00
462 Lightcraft AGT 146 / P3-1 double c/w PLC 26W lamp Set 435.00
463 Lightcraft AGT 180 / P3-1 lantern & ballast c/w Set 365.00
PLC 26W lamp
464 Lightcraft AGT 180 / P3-1 telescopic post / 1 white Set 195.00
head post c/w holder, plastic shade and PLC 26W
465 FABRIKANT 8003 twin obstruction light, lighting control Set 1250.00
box and change over relay c/w bracket and on roof 42mm
dia. Hot dipped galvanised steel pipe mounted on roof
deck and secured by 3 Nos. stainless steel cable support
466 WE-EF 808-E2-100 Twin obstruction light c/w 8000hr Set 1250.00
Claude Kryton lamps, lighting control box and change
over relay, brackets and 43mm dia. Hot dipped galvanised
steel pipe mounted on roof deck and secured by 3 nos.
stainless steel cable support
472 Earth rod 16mm diameter copper-weld rod mild steel No 109.00
3.6m long driven in ground, complete with bronze clamp,
and coupling interconnecting 25mm x 3mm copper tape
(not exceeding 5m) and galvanised hinged lid inspection pit
473 Earth rod 16mm diameter copper-weld rod mild steel No 28.70
1.8m long driven in ground, complete with bronze coupling
(Furse, Emtech, HS, Heng, NSI )
481 Earth clip/clamp for water pipe/gas pipe bonding diameter No 3.00
12mm - 75mm c/w label
482 PUB approved earth rod to tape A type earthing clamp No 12.00
c/w label (Heng, HS, NSI)
484 236 x 236 x 230mm polymer earth eletrode inspection pit No 33.00
485 Electrical joint compound for earthing rod cap Tube 60.00
(8 oz plastic tube type)
MISCELLANEOUS
486 Take delivery from any store, transport, cut stem as No 33.20
required and fix fan and regulator (hook not included)
489 Supply and fix approved powered drive masonry pin No 0.60
including the use of cartridges
490 Labour only taking down, removing and refixing No. 15.00
ceiling fans and regulators in new position not
exceeding 200mm distance
492 Labour for taking down wall fan in hawker centre or Per Job 13.00
other parts of any building for cleaning, oiling, servicing
& refixing after work completion
493 Labour only for refixing loose and fallen teak battens m 1.20
including replacement of wall plugs where necessary
(where work involved in this item does not exceed 10m,
a minimum charge of 10m applies)
495 Labour only for refixing loose and fallen wirinng m 1.20
including supply of additonal saddles or clips
(where work involved in this item does not exceed 10m,
a minimum charge of 10m applies)
(Scaffolding measured separately)
496 Hacking existing rc slab not exceeding 225mm thick to form opening 9.00
opening 150mm x 75mm for trunking including making
good all works disturbed and to match existing with paint
497 Patch up openings for pipes / conduit exceeding 100mm dia No 5.00
but not exceedidng 225mm dia. With cement and sand (1:3)
including approved waterproof compounds in wall and
floor not exceeding 225mm thick and make good to match
existing
498 Labour only for refixing loose or fallen ceiling blocks / wood No 1.20
blocks including the replacement of wood plugs
where necessary
500 Labour only for refixing loose electrical fittings and No 6.00
accessories including the replacment of wood plugs where
necessary / labour to convert ceiling rose of light fitting
to cable & PVC trunking including all necessary parts
& fitting for the connection work
501 Refix loose galvanised steel conduit 20mm diameter Per Job 10.50
pipes at gable end wall including new hasp clip, saddle
clams and screws
502 Labour to check and tighten the loose cable connection Per Job 20.00
for fuses, MCCB's and busbars in the main switchboard
503 Labour only for removing unauthorised wirings, battens, Per Job 15.00
in vacant flat, touch up all plug holes with putty and all
affected work to match existing with paint
507 Supply and fix 150 x 180 x 70 mm approved metal box with No 26.00
cam lock and hidden hinges to wall for 13 Amp socket
outlet (measure separately)
508 Labour only for checking and attending to defective Per Job 30.00
light in community hall and other parts of building
exceeding 8m height inclcuding use of movable metal
scaffolding (parts and fittings will be paid separately)
510 Supply and fix 125W or 250W procelain lamp holder No 18.10
inclcuding use of movable metal scaffolding
511 Supply and fix 150/200W spot light fitting complete with No 33.30
base holder to wall or ceiling and including making
good all work disturbed
512 Padlock for public fitting 'Yale' 713 / 40mm or other approved No 6.00
514 Supply and install 60A TPN tap-off box c/w fuse 'CIAMA' No 400.00
516 Labour and material only for modifying the existing No 6.00
fluorescent light fitting for installation of electronic or
low loss ballast including supply of necessary wiring
517 Supply and fix PUB's approved first aid chart in switchroom No 20.00
518 Labour tocheck, clean and tighten the 1st 5 nos. of loose No 4.00
neutral connector or line tap/line connector including
replacement of defective screws (within same block)
519 Labour tocheck, clean and tighten the remaining nos. of No 2.00
loose neutral connector or line tap/line connector including
replacement of defective screws (within same block)
520 350mm x 200mm x 170mm metal box with 165mm x 200mm x No 118.40
15mm metal mounting plates, welded internally an centrally
to base of metal box fabricated from 1.2mm thich
electro-galvanised sheet steel c/w hidden door hinges,
waterproofing seals, 2 nos. 6mm dia steel thumb screw
with plastic knobs, earth terminal and treated with paint
finish of 45 microns oven baked and dried.
(For 30 Amp MCCB)
521 Supply, deliver and install metal box fabricated from m2 375.00
1.6mmthick, electro-galvanised sheet steel complete with
hidden door hinges, water-proofing seals, lock facilities,
treated with paint finish of 45 microns overbaked & dried
(overall 260mm thickness)
522 Supply, deliver and install metal box fabricated from m2 400.00
1.6mmthick, electro-galvanised sheet steel complete with
hidden door hinges, weather proofing seals, lock facilities,
treated with paint finish of 45 microns overbaked & dried
(overall 300mm thickness)
523 Supply, deliver and install metal box fabricated from m2 435.00
1.6mmthick, electro-galvanised sheet steel complete with
hidden door hinges, weather proofing seals, lock facilities,
treated with paint finish of 45 microns overbaked & dried
(overall 350mm thickness)
524 Supply, deliver and install metal box fabricated from m2 498.00
1.6mmthick, electro-galvanised sheet steel complete with
hidden door hinges, weather proofing seals, lock facilities,
treated with paint finish of 45 microns overbaked & dried
(overall 400mm thickness)
525 Labour for checking firmness of ceiling fan bracket/hook, Per Fan 15.00
taking down ceiling fans in hawker centres or other
buildings as directed, dismantling the mechanical
connecting components to check for worn bolt / rivets,
corroded hanging rod and bolt assembly without split
cotter pins and replacing these parts (parts measured
separately ) if necessary, including cleaning fans and
refixing on completion
526 Labour nly for dismantling and re-fixing the illuminated No 35.00
Block No. / Carpark Signages for the purpose of carrying
out the repair / replacement of defective fluorescent
tubes, starters, ballasts etc inclusive of metal scaffoldings
not exceeding 6.5m height ( Parts and fittings shall be
measured separately )
527 Labour nly for dismantling and re-fixing the illuminated No 45.00
Block No. / Carpark Signages for the purpose of carrying
out the repair / replacement of defective fluorescent
tubes, starters, ballasts etc inclusive of metal scaffoldings
exceeding 6.5m height but ecceeding 15m height.
( parts and fittings shall be measured separately )
530 Supply and isntall A1 size wooden framing for single No 50.00
line diagram in switchroom
DAYWORK
533 Services rendered by skilled electriician for resetting of Per Hour 9.00
MCCB / earth fault relay / overcurrent electrical faults
( after officer hours or on Saturday, Sunday and Public
Holidays) for a minimum of 4 hours
535 Services rendered by licensed cable detection worker Per Hour 115.00
for site excavation using mechanical means for laying of
underground cables / erection of lighting columns for
a minimum of 1 1/2hours
538 Injection test for 1 No. ACB / MCCB ( with earth fault / No 850.00
overcurrent protections ) by PSPL / PGPL registered testing
engineer including submission of shutdown form to
PSPL / PGPL, arrangement for shutdown etc for testing
and providing temporary electrical supply and skilled
electricians, equipment and transportation cost -
during office hours i.e 8.00 am to 5.30 pm
539 Injection test for each additional circuit breaker ( with No 600.00
earth fault / overcurrent protections ) within the same
switchroom as item 538
540 Injection test for 1 No. ACB / MCCB ( with earth fault / No 1200.00
overcurrent protections ) PSPL / PGPL registered testing
engineer including submission of shutdown form to
PSPL / PGPL, arrangement for shutdown etc for testing
and providing temporary electrical supply and skilled
electricians, equipment and transportation cost - after
office hours or on Saturday, Sunday and Public Holiday
549 Supply of PUB Licensed Cable Jointer to carry out Per Job 150.00
"Live" termination of CTS cabales at OG bet
550 Supply of PUB authoirsed small installation tester (ASIT) Per Job 100.00
to test electrical extensions and submission of report to
PUB / Town Council
551 Excavate trench 300 x 750 mm deep by hand, sand bed m 3.90
and backfilling as specified for cable (s) in trench
554 Supply and turf good quality 25mm thick cow grass close m2 4.00
turfing including 125mm thick top soil and well watering
and tendering to ensure growth of turfs.
555 Supply and install brass compression glands ( Type BW) No 9.90
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 6mm2 2 core
PVC / SWA / PVC cables
556 Supply and install brass compression glands ( Type BW) No 11.60
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 10mm2 2 core
PVC / SWA / PVC cables
557 Supply and install brass compression glands ( Type BW) No 12.20
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 16mm2 2 core
PVC / SWA / PVC cables
558 Supply and install brass compression glands ( Type BW) No 12.20
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 25mm2 2 core
PVC / SWA / PVC cables
559 Supply and install brass compression glands ( Type BW) No 18.40
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 50mm2 2 core
PVC / SWA / PVC cables
560 Supply and install brass compression glands ( Type BW) No 10.50
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 6mm2 4 core
PVC / SWA / PVC cables
561 Supply and install brass compression glands ( Type BW) No 12.40
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 10mm2 4 core
PVC / SWA / PVC cables
562 Supply and install brass compression glands ( Type BW) No 15.10
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 16mm2 4 core
PVC / SWA / PVC cables
563 Supply and install brass compression glands ( Type BW) No 18.00
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 25mm2 4 core
PVC / SWA / PVC cables
564 Supply and install brass compression glands ( Type BW) No 19.10
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 35mm2 4 core
565 Supply and install brass compression glands ( Type BW) No 20.30
including brass locknut, earth tags, shroud, connection
to cable and mounting bracket for 50mm2 4 core
PVC / SWA / PVC cables
JOINTS
577 Supply and fix catenary wire between lamp posts to m 0.70
support cables
581 ' BICC ' Cat No. G72522-03 or other approved cable with No 35.00
glandplate and wormdrive clips for attaching to street
lighting cutout
582 ' BICC ' Cat No. G72569-02 or other approved 3 phase No 56.00
adaptor with bottom plate for attaching to street
lighting cutout
608 ' INDALUX ' post top polycarborate clear diffuser No 499.00
lantern cat no 250-IJB-RK complete with 80E / 125W
HPL-N lamp and intergral control gear
609 ' INDALUX ' post top polycarborate clear diffuser No 520.00
lantern cat no 250-IJB-RK complete with 70W / 50W
SON lamp and intergral control gear
612 ' INDALUX ' QUEBEC 125-IQC' post top lantern c/w No 600.00
aluminium canopy, intergral control gear, polycarbonate
frosted sphere and 1 x 125W / 80W mercury vapour lamp
613 ' INDALUX ' QUEBEC 125-IQC' post top lantern c/w No 680.00
aluminium canopy, intergral control gear, polycarbonate
frosted sphere and 1 x 70W SON lamp
614 ' INDALUX ' QUEBEC 150-IQC' post top lantern c/w No 690.00
aluminium canopy, intergral control gear, polycarbonate
frosted sphere and 1 x 70W SON lamp
615 ' INDALUX ' post top lantern model IJK c/w 125W HPL No 533.60
lamp and integral control gear
618 'PGL' post top polycarborate clear / smoke 400 mm diameter No 295.00
spherical lantern cat no. P/4C c/w 80W / 125W HP-N lamp
and integral control gear
620 'PGL' post top polycarborate clear / smoke 400 mm diameter No 352.00
spherical lantern cat no. P/4C c/w 70W son lamp
and integral control gear
622 'PGL' post top polycarborate 500 X 500 mm clear / smoke No 440.00
lantern cat no. P / 5 x 5C c/w 70W SON lamp
and integral control gear
626 ' RAAK' Elipse post top lantern cat no. s-2389.1321 No 608.00
complete with 70W SON lamp and integral control gear
627 ' RAAK' post top kosmos 430 mm diameter Lantern No 698.80
cat no. S2280 . 8000 complete with 80W HPL-N lamp
and integral control gear
628 ' RAAK' post top kosmos 430 mm diameter Lantern No 790.80
cat no. S2280 . 7000 complete with 70W HPL-N lamp
and integral control gear
630 ' Philips ' post top Lantern cat no. HPP 131, opal - white No 337.00
sphere with black rim, complete with 80W HPL - N lamp
and integral control gear
631 ' Philips ' post top Lantern cat no. HPP 131, opal - white No 337.00
sphere with black rim, complete with 125W HPL - N lamp
and integral control gear
632 ' Philips ' post top Lantern cat no. SPP 131, opal - white No 298.00
sphere with black rim, complete with 70W SON lamp
and integral control gear
635 'Philips' post top lantern cat no. HPP 134, opal-white No 303.00
elipse, complete with 80W HPL-N lamp and integral
control gear
636 'Philips' post top lantern cat no. HPP 134, opal-white No 309.00
elipse, complete with 125W HPLN lamp and integral
control gear
637 'Philips' post top lantern cat no. SPP 134, opal-white No 323.00
elipse, complete with 70W SON lamp and integral
control gear
638 'Philips' post top lantern cat no. HPP 136, opal-white No 294.00
cone, complete with 80W HPL-N lamp and integral
control gear
639 'Philips' post top lantern cat no. HPP 136, opal-white No 297.00
cone, complete with 125W HPL-N lamp and integral
control gear
640 'Philips' post top lantern cat no. SPP 136, opal-white No 303.00
cone, complete with 70W SON lamp and integral
control gear
641 'Philips' post top lantern cat no. HPP 137, mushroom, No 350.00
complete with 80W HPL-N lamp and integral
control gear
642 'Philips' post top lantern cat no. HPP 137, mushroom, No 352.00
complete with 125W HPL-N lamp and integral
control gear
643 'Philips' post top lantern cat no. SPP 137, mushroom, No 352.00
complete with 70W SON lamp and integral control gear
648 'Mazda' ' CYCAR' 400 Opal M80 / S70 post-top lantern c/w No 325.00
integral control gear and 1 x 80W HPL-N / 70W SON lamp
649 'Mazda' ' TAKEO' M80 / S70 post-top lantern with No 380.00
circular overlapping canopy complete with 80W HPL-N
lamp or 70W SON lamp and integral control gear
650 'Mazda' ' OPALA ' M80 / 'opala' S70 post-top lantern No 296.00
IP 549 c/w 400mm diameter polycarbonate diffuser and
1 x 80W HPL-N / 70W SON lamp
651 'Mazda' Agate S70 / M80 / 'opala' S70 post-top lantern No 405.00
IP 549 c/w 500mm diameter oroglass diffuser, inegral
control gear & 80W HPL-N or 70W SON lamp
652 'ERNST ' 381006 post top lantern c/w 125W mercury No 859.05
vapour lamp and inegral control gear
653 'ERNST ' 370104 post top lantern c/w 125W mercury No 801.55
vapour lamp and inegral control gear
683 WE-EF MA 30-E-70 / NI (K) post top lantern with Set 543.00
corrosion-resistant die-cast aluminium alloy base
and canopy. Opal diffusing cone in vandal resistant
UV stabilized high density Polyethylene (HDPE-S)
and complete with 70W Sodium integral control
gear and lamp
684 'Siemen' Cat 5NA 5482-ICKO Post top lantern c/w No 650.00
built in 80 / 125W high pressure mercury lamp and
control gear
685 'Siemen' Cat 5NA 5482-ICKO Post top lantern c/w No 695.00
built in 50 / 70W high pressure sodium lamp and
control gear
700 400 x 400 x 300 thick grade 25 concrete block act as No 15.90
base for bollards including reinstatement of ground
701 'Philips' decorative bollard cat no. HGC 130 with No 441.00
opal-white cube and vandal-resistant glass-fibre
reinforced polyester column complete with 80W
NPL-N lamp and integral control gear
FLOODLIGHT LUMINAIRES
734 'THORN' area floodlight cat no. OAC 400T complete No 612.00
with stirrup mounting bracket, integral control
gear and 400W-MBIF lamp
735 'THORN' area floodlight cat no. OAK 400T complete No 532.00
with stirrup mounting bracket, integral control
gear and 400W-MBF / U lamp
736 'THORN' area floodlight cat no. OAC 250T complete No 578.00
with stirrup mounting bracket, integral control gear
and 250W MBIF lamp
738 'THORN' are floodlight cat no. CAST 250 complete No 578.00
with stirrup mounting bracket integral control
gear and 250w SON - T lamp
746 Similar to item 745 but c/w 400w hiigh pressure No 450.00
sodium / 400w metal halide lamp
752 ' Siemens ' EUROFLOOD 250 / 400 SICOMPACT mini No 690.00
floodlight c/w 250 / 4000W metal halide or high pressure
sodium lamp and control gear
757 ' Philip' Anti Glare Weatherproof floodlight Cat No. No 378.00
SNF 201 c/w 250W SON / T and one pre-wired
weatherproof die-cast control gear box
758 ' Philip' Anti Glare Weatherproof floodlight Cat No. No 435.00
SNF 201 c/w 400W HDL/ T lamp and one pre-wired
weatherproof die-cast control gear box
759 Philip' Bulk head luminaire Cat No. XGC001 complete No 181.00
with prismatic deffuser, 18W soX lamp, control gear
and mounting bracket
760 Selux ' MTR luminaire Cat No. SX 563 11 - 2 complete No 900.00
with 70W SON lamp, MTR 200 refractor and accessories
764 ' Philips' Cat No. SRC 501 or SGS 201 / 070G complete No 259.00
with 70W SON - T lamp
765 Thorn ' Cat No. QB 79 WNB 1070 complete with 70W No 230.00
SON - T lamp
766 Madza ' COMETE PF S70 Steel lantern c/w integral No 320.00
control gear, cover bowl and 70W son lamp / 125W
mercury lamp
767 SIEMEN SRL S70 complete with 70W SON-T lamp No 260.00
770 Siemens' Cat No. 5NA 3332-IS c/w built-in 150W high No 400.00
pressure sodium lamp and control gear
771 ' Philips ' Cat No. HGS 201 or HRC 510 / 080 - 125G No 236.00
complete with 125W HPL - N lamp
772 ' Thorn ' Cat No. QB79WB1125 complete with 125W No 219.00
MBF / U lamp
773 ' Madza ' MACADAM Cat No PF M125 complete with No 300.00
125W mercury vapour lamp, control gear and cover bowl
774 ' Siemens ' Cat No. 5NA3322-1D complete with built-in No 230.00
125W high pressure mercury lamp and control gear
775 ' Simens ' MRL 6150 complete with 150W SON lamp No 311.00
776 ' Madza ' MACADAM GS 150 street lantern complete No 390.00
with integral control gear, cover bowl and 150W SON lamp
777 ' Philips ' Cat No. SGS 203 or SGS 201 / 150G complete No 400.00
with 150W SON lamp
778 ' Habbell ' Cat No. RMA- 3 - 3 / RMD - 15S2E - 3 No 471.00
complete with 150W SON lamp
779 ' EYE ' Cat No. H788E complete with 150W SON lamp No 446.00
780 ' Madza ' COMETE LIF S150 street lantern complete No 530.00
with integral control gear, cover bowl and 150W SON
lamp
781 70W SON deluxe Elliptical / Tubular high pressure sodium No 43.00
vapour lamp with E27 base, ' Philips ' or other approved
type
782 150W SON high pressure sodium vapour lamp with No 58.00
E40 base, ' Philips ' or other approved type
783 250W SON deluxe Elliptical / Tubular high pressure sodium No 65.00
vapour lamp with E40 base, ( ' Philips ', Oram or Thorn )
784 50W / 80W / 125W HPL - comford high pressure mercury No 28.00
vapour flourescent lamp with E27 base ( 'Philips' or Osram )
785 400W HPI Bus high pressure metal halide gas discharge No 129.00
lamp with E40 base, ' Philips ' or other approved type
( built-in ignitor )
788 400W MBIF high pressure metal halide lamp G53455 No 131.00
ignitor & E40, porcelain lampholder, 'Thorn' or other
approved type.
789 250W MBIF metal halide lamp with metallic additives No 126.00
ignitor & E40 base 'Thorn' or other approved type
793 150W SON lamp ballast, BSN 150 L34 ' Philips' or other No 65.00
approved
796 80W / 125W high pressure mercury lamp ballast, BHL 80 No 49.00
L32/BHL 125 L32 'Philips' or other approved
797 250W high pressure mercury lamp ballast, BHL 250 L32 No 60.00
Philips' or other approved
798 400W high pressure mercury lamp ballast, BHL 400 L32 No 75.00
Philips' or other approved
803 Ballast for PLC 13W / 18W lamp 'Philips' or other approved No 16.00
807 160 x 135 x 77 mm plastic rectangular base, ' Legrand ' No 21.70
Cat No. 92106 or other approved
810 Prepare and paint one coat of primer and two coats of No 13.30
synthetic enamel paint, onto the external surface of the
lighting columns for 8m street lighting colums with
single arm bracket
811 Prepare and paint one coat of primer and two coats of No 14.10
synthetic enamel paint, onto the external surface of the
lighting columns for 8m street lighting colums with
double arm bracket
812 Prepare and paint one coat of primer and two coats of No 8.30
synthetic enamel paint, onto the external surface of the
lighting columns for 3m post top lighting column
813 Prepare and paint one cost of primer and two coats of No 12.20
synthetic enamel paint, onto the external surface of the
lighting columns for 8m post top lighting column
814 Prepare and paint one coat of primer and two coats of No 15.60
synthetic enamel paint, onto the external surface of the
lighting columns for 10m post top lighting column
815 Prepare and paint one coat approved aluminium paint No 12.20
to existing lamp poles including spraying lamp post
indicator with approved black paint and all necessary
supports, etc
816 Prepare and paint two coats approved aluminium paint No 17.20
to existing lamp poles including spraying lamp post
indicator with approved black paint and all necessary
supports, etc
817 Paint identification numbers (Block No. / Lamp Pole No.) Pole 1.80
on to existing lamp poles of size not exceeding 150 mm
in height
820 8 metre post top HOT DIP GALVANSIED lighting column No 700.00
all as shown including all necessary concrete foundation,
cement skirting, excavation, backfilling and reinstatement
of ground surfaces
821 10 metre post top HOT DIP GALVANISED lighting column No 790.00
all as shown including all necessary concrete foundation,
cement skirtng, excavation, backfilling and reinstatement
of ground surfaces
824 Double quarter arm 3.5 - metre HOT DIP GALVANISED No 527.00
lighting column and powder coated black colour
825 Single quarter arm 3.5 - metre HOT DIP GALVANISED No 634.00
lighting column and powder coated black colour
826 Supply and fix hotdip galvanised bracket metal arm to No 103.00
lighting column to match existing (single arm)
827 Supply and fix hot dip galvanised bracket metal arm to No 140.00
lighting column to match exisitng (double arm)
828 Supply and fix 80mm diameter 200mm length steel adaptor No 42.00
with spigot to lighting column for mounting or post top
lantern c/w mounting screws
830 Supply and fix corrosion resistant aluminium wall bracket, No 117.00
'PGL' Cat No. P/BM-448 or other approved type
831 Supply and fix corrosion resistant aluminium double arm No 268.00
bracket for post top mounting, 'PGL' Cat No. P/T-2 or
other approved
832 Supply and fix corrosion resistant aluminium triple arm No 325.00
bracket for post top mounting, 'PGL' Cat No. P/T-3 or
other approved
838 Supply and fix steel mounted bracket for single flood No 80.00
light luminaire on post top column
839 Supply and fix steel mounted bracket for two flood No 120.00
lights luminaires on post top column
858 " Philips " Cat No. SGS 201-070G / SRC 510 - 070G No 54.00
862 " Philips " Cat No. HGS 201 / HRC 510 / 080 - 125G No 59.00
865 " Philips " Cat No. SGS 201 / SGS 203 / 150G No 60.00
867 Skilled electrician for checking defective witing, fuses, Per Job 23.00
times switches, including repair where necessary in meter
room / control box
868 Labour for checking defective lamp post wiring, fuses, Per Post 17.00
including tracing fault & repair where necessary
869 Labour only for removal or tighting stay wire from Per Post 10.00
lamp post
871 Labour for removing existing / defective 5 to 12 m lighting Per Pole 69.00
column including bracket arm & luminaire
(excluding excavation)
872 Labour for refixing loosen lamp cover Per Pole 6.50
873 Labour for removing existing / defective 3 to 4 m lighting Per Pole 48.00
column including bracket arm & luminaire
(excluding excavation)
874 Labour for refixing loosen lamp fitting Per Pole 6.50
875 Labour for dismantling single / double lamp post arm Per Pole 29.90
876 Labour for refixing single / double arm to lamp post Per Pole 29.90
877 Labour for repositioning single / double arm to lamp Per Pole 29.90
poast's arm
878 Labour for repositioning and realigning lamp post not Per Pole 57.00
exceeding 4 m height including all necessary excavation
and make good all works affected on completion
879 Labour for repositioning and realigning lamp post exceeding Per Pole 89.00
4m but not exceeding 8 m height including all necessary
excavation and make good all works affected on completion
880 Labour for repositioning and realigning lamp post exceeding Per Pole 101.00
8m but not exceeding 12 m height including all necessary
excavation and make good all works affected on completion
881 Labour for checking and locating underground cable Per Pole 133.00
short-fault c/w excavation and make good all works
affected on completion
882 Ripple control receiver for existing public lighting installation No 340.00
- two relay type
883 Ripple control receiver for existing public lighting installation No 400.00
- three relay type
884 Supply and replace post top 400 mm diameter polycarbonate No 144.00
opal white sphere (other than FABRIKANT & WE - EF)
886 Supply and install metal base for post top spheric lantern No 37.00
c/w mounting screws and connections
888 Provide 300 - 450 mm high concrete pedestal base for No 61.00
westherproof / outdoor control box c/w mounting screws
and brackets
889 Supply and install 200 watt E / 27 Rough Device lamp bulb No 12.00
891 Supply and install timer relay c/w base for zebra crossing No 120
warning light
892 Supply and install post top yellow globe 300mm diameter No 180
for zebra crossing
893 Rental for the 'Wildcat' self propelled work platforms Per Mth 1600
Model 2032 with working height of 7.90m, overall length
2.30m, platforms capacity 800 lbs