Professional Documents
Culture Documents
Safetying with Lockwire
Safetying with Lockwire
Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
WARNING: USE PROTECTIVE GOGGLES AND GLOVES EACH TIME YOU CUT LOCKWIRE. DISCAR
D LOOSE OR USED LOCKWIRE IMMEDIATELY. LOOSE OR USED LOCKWIRE CAN CU
T YOU OR MAKE YOU BLIND.
QT
REFERENCE DESIGNATION
Y
No specific 1 PLIERS - TWISTING, SPECIAL
B. Referenced Information
REFERENCE DESIGNATION
Ref. Fig. General Wirelocking Rules
Ref. Fig. Double Wirelocking Method - Examples
Ref. Fig. Double Wirelocking Method on Bulkhead Adaptors - Examples
Ref. Fig. Single Wirelocking Method - Examples
Ref. Fig. Double Wirelocking - Twisting Method
Ref. Fig. Single Wirelocking - Twisting Method
3. Job Set-up
SUBTASK 20-11-11-911-054-A
A. General Wirelocking Rules
Ref. Fig. General Wirelocking Rules
(1) Installation rules:
(d) When you install lockwire, make sure that there will not be chafing or fatigue.
This is to prevent damage to the lockwire or adjacent parts. The causes of chafi
ng or damage are vibrations or increased tension on the wire to prevent loosen
ing of the locked items.
© AIRBUS S.A.S. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT.
about:blank 1/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
(e) Wirelocking of installed flexible components or assemblies must not have an eff
ect on the quality of the installation or the locking during operation.
(f) Do not use lockwire to prevent unwanted operation of controls or switches for n
ormal, standby or emergency services which can be necessary during flight.
(h) The length of wire between the attachment points must be as short as possibl
e.
(i) When you safety with lockwire in the fuel tank areas, make sure that there is n
o protrusion of the wire ends:
- For the single wire method, you must twist the wire end with protrusion
back to the wire.
- For the double wire method, you must bend the wire ends with protrusio
n back to the wire or the part that you lock (e.g. screw/nut).
(2) Minimum distance between the wire and parts that move
The minimum distance between a length of lockwire without support and parts that m
ove is 15 mm (0.5906 in.).
(3) Wire direction
(a) General
The line of approach of the lockwire must be approximately tangential to the p
arts that you will lock.
When you install the lockwire, the strand that goes through the hole will tighte
n the locked item.
It is important to identify items with left hand and right hand threads carefully.
When you use an anchor lug, the wiring must start at the lug and the lug must
align with the wire. The wire must not cause radial movement of the lug.
about:blank 2/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
SUBTASK 20-11-11-911-055-A
B. Additional Pipe Wirelocking Rules
(1) When you connect a pipe to a plug-in union, lockwire the pipe swivel nut to the comp
onent and not to the plug-in union.
(2) You can lock the adjacent plug-in unions or swivel nuts together.
(3) Do not use the same wire to lock more than two plug-in unions or swivel nuts.
SUBTASK 20-11-11-911-056-A
C. Wirelocking Methods
(1) Double wire method:
Ref. Fig. Double Wirelocking Method - Examples
Ref. Fig. Double Wirelocking Method on Bulkhead Adaptors - Examples
The recommended method is the "double-twist method".
The maximum distance between fasteners is 100 mm (3.94 in.).
If the distance is more than 100 mm (3.94 in.):
- Use one more attachment point.
- The maximum length of wire is 600 mm (23.62 in.).
You can safety a maximum of 3 items together with lockwire.
(2) Single wire method:
Ref. Fig. Single Wirelocking Method - Examples
Use only the single wire method if specified in the related task.
The maximum length of lockwire is 600 mm (23.62 in.).
SUBTASK 20-11-11-911-057-A
D. Precautions Before Wirelocking
(1) Make sure that all lockwire holes are drilled.
(2) Make sure that the assembly was torqued to the requirements of the related task.
4. Procedure
SUBTASK 20-11-11-911-061-A
A. Double Wirelocking
© AIRBUS S.A.S. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT.
about:blank 3/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
NOTE: There must be the same length of lockwire on each side of the fastener.
(2) Bend one lockwire end around the fastener head (1) to the fastener head (2).
(3) Bend this lockwire end around the other lockwire end.
(4) Use PLIERS - TWISTING, SPECIAL to twist the lockwire clockwise at a maximum angl
e of 60°:
- Do not put too much tension on the wire.
- To prevent damage to the lockwire during this step, refer to the table that follo
ws:
Keep the lockwire tight during the twisting, until the twisted part comes very near to t
he hole in the next unit.
(5) Pull one lockwire end through the fastener head (2) when the twisted part is near it (l
ess than 3 mm (0.1181 in.)).
For wirelocking of 3 nuts or bolt heads, twist the lockwire in one direction between th
e first two items. Then twist it in the opposite direction between the second and third
items.
NOTE: The direction of the wrap and the twisted strands must be such that the loop
around the part comes below the strands that go out of the hole. Thus the lo
op will stay down and will not become loose.
(6) Pull the other lockwire end around the fastener head (2).
(7) Twist the strands in the direction that will cause the lower lockwire to always be pulle
d down.
The length of this twisted part (pigtail) must be between 10 mm (0.39 in.) minimum
and 15 mm (0.59 in.) maximum.
(8) If necessary, cut and discard the unwanted length of lockwire:
- You must collect the cut-off material to prevent damage to the aircraft.
(9) Bend the pigtail around the fastener head (2).
(10) When you safety with lockwire in the fuel tank areas, make sure that you bend the wi
re ends with protrusion along the wires. You must also make sure that the wire ends
stay near to the wire or the part that you lock.
(11) Make sure that there is tension in the lockwire.
© AIRBUS S.A.S. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT.
about:blank 4/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
(12) Make sure that there are no signs of damage (nicks, kinks) on the lockwire. This does
not include the abrasion caused by the PLIERS - TWISTING, SPECIAL.
SUBTASK 20-11-11-911-062-A
B. Single Wirelocking
Ref. Fig. Single Wirelocking - Twisting Method
(1) Put the lockwire into the locking hole of the bolt (1) (see detail A).
(2) Keep the lockwire tight, twist a minimum of four times.
(3) Put one end of the lockwire through the locking hole of the bolt (2) (see detail B).
NOTE: Airbus recommends that you do not cut the end that is not used until the wir
elocking operation is completed. You can use it if the first end breaks.
(4) Bend the lockwire back by 180° and below itself (see detail C).
(5) Pull the lockwire tight and make it go around and below itself again until you get betw
een two and four full turns.
(6) If necessary, cut and discard the unwanted length of lockwire:
- You must collect the cut-off material to prevent damage to the aircraft.
(7) Make sure that there is tension in the lockwire.
(8) Make sure that there are no signs of damage (nicks, kinks) on the lockwire.
5. Close-up
SUBTASK 20-11-11-911-063-A
A. Check of the Wirelocking
(1) Discard the remaining wire.
(2) Remove all pieces of cut-off lockwire from the aircraft structure.
about:blank 5/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
TENSION
DIRECTION OF ROTATION
TO LOOSEN THE SCREW
TENSION
< 100mm
(< 3.94in.)
ATTACHMENT POINT USED FOR WIRELOCKING WHEN DISTANCE IS MORE THAN 100mm (3.94in.)
45° MIN
N_MM_201111_2_EAM0_01_00
about:blank 6/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
1 2 3 4
RH TWIST
LH TWIST
RH TWIST
LH TWIST
PIGTAIL PIGTAIL
5 6 7 8
45° MINIMUM
9 10 11
12 13
N_MM_201111_2_AAM0_01_02
about:blank 7/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
A B
A 01
THE UNION OUTER SLEEVES THAT YOU MUST B 02
A B
A B
A A 01 B B 02
THE LOCKNUT AND THE UNION BODY THAT YOU MUST
SAFETY WITH LOCKWIRE TO ONE OF THE ALTERNATIVE
FIXED ANCHOR POINTS SHOWN. THE OUTER SLEEVES ARE
SAFETIED WITH LOCKWIRE TO THE LOCKNUT OR THE
UNION BODY.
NOTE:
01 ATTACHMENT TAG BELOW THE BOLT HEAD OR THE NUT.
02 DRILLED NUT OR BOLT HEAD. N_MM_201111_2_GAM0_01_00
about:blank 8/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
C D D
C D D
C C D D 03
NOTE:
03 TYPICAL N_MM_201111_2_GAM0_02_00
about:blank 9/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
N_MM_201111_2_BAM0_01_00
about:blank 10/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
1
1
2 2
STEP 1 STEP 2
1 1 1
60°
MAXIMUM
2 2
2
PIGTAIL
N_MM_201111_2_CAM0_01_00
about:blank 11/12
29/5/24, 0:37 AVA - A318 / A319 / A320 / A321 - AMM - 01-May-2024 - 20-11-11-911-001-A - Safetying with Lockwire
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 20-11-11-911-001-A - Safetying with
AVA AMM 01-May-2024 68
A320 Lockwire
TAIL NUMBER - MSN - FSN:
Print date: 2024-06-03 06:20:45
B
C
1
1
2 2
N_MM_201111_2_DAM0_01_00
about:blank 12/12