Professional Documents
Culture Documents
4415_instal
4415_instal
Radio 4415
Installation Instructions
Disclaimer
The contents of this document are subject to revision without notice due to
continued progress in methodology, design and manufacturing. Ericsson shall
have no liability for any error or damage of any kind resulting from the use of
this document.
Trademark List
All trademarks mentioned herein are the property of their respective owners.
These are shown in the document Trademark Information.
Contents
1 Introduction 1
1.1 Documentation 1
1.2 Tools 1
1.3 Conditions 2
2 Work Process 4
4 Installation Alternatives 7
4.1 Mounting Direction Alternatives 8
6 Install Radio 15
6.1 Install Multiple Radios 15
6.2 Video 15
6.3 Assemble Single Pole Clamp (Optional) 15
6.4 Hoist Radio 16
6.5 Attach Radio to Rail 17
6.6 Attach Radio to Single Pole Clamp (Optional) 18
6.7 Connect Cables 19
6.8 Optional Actions 27
9 References 35
1 Introduction
1.1 Documentation
Make sure that the following
documents are read and understood:
• Personal Health and Safety
Information
1.2 Tools
Product Name
Electrostatic Discharge (ESD) wrist strap (static
control wrist strap)
Product Name
Torque wrench 5–25 Nm, socket 13 mm
Lifting device
1.3 Conditions
The conditions in this section must be fulfilled before work starts.
• The rail is installed on the site. For more information on how to install the
rail, refer to Install Rail.
• The power supply for the radio is installed and tested at the radio site.
– A circuit breaker
2 Work Process
Install Radio
Verify Radio
Installation
Power Up Radio
Check Radio
After Power Up
Perform Concluding
Routines
Ge7475D
Note: The radio must not be left in an outdoor environment for more than
one week before taking it into service. In cases where high humidity
or cold temperatures apply, the radio must be powered up within 48
hours.
Steps
Ge8584A
Ge6679C
Ge8585A
Ge8260A
4 Installation Alternatives
A B
Ge7629S
2
1
Ge12358A
1.7 Nm
Ge7788C
Ge7789D
1.7 Nm
Ge7608D
Ge9174A
Ge7790C
Ge9637B
Ge8387A
Ge8388A
22 Nm
Ge7368F
Steps
Ge10637A
Ge9968A
Ge9971A
Steps
OFF
Ge6817D
Ge6243C
3. Assembly
Assemble the DC power
Instruction connector according to the
instructions delivered with the DC
power connector. Make sure that
the cable shield is properly
connected in the DC power
connector.
Ge7361B
Note:
The wires of the power cable can
have different colors. Make sure
that the wires are connected to
the correct polarities.
Ge6242B
6 Install Radio
Warning!
When working at height, there is a risk of falling objects. Falling objects can cause
serious injury or even be fatal. Always wear a helmet and avoid standing in an area
where objects can fall.
Steps
3. Before attaching the outer radios to the rail, connect the cables to the
outer radios.
4. Attach the outer radios to the rail, one at either side of the middle radio.
6.2 Video
The video of a pole installation shown in Macro Radio Installation Video is a
complement to the step-by-step installation instructions.
Steps
20 Nm
Ge9969A
Ge9970A
Note: Do not hoist more than one radio in the same handle; the handle
might break.
Steps
Ge2097G
Ge2097E
Steps
Ge7369B
Ge7370B
Ge7871A
Ge7371D
Steps
Ge9972A
22 Nm
Ge9973A
Because of space limitations, always connect the cables in the following order:
Steps
2. Connect the power cable, see Connect Power Cable on page 23.
3. Connect the optical cable, see Connect Optical Cable on page 23.
4. Connect the ALD (RET) cable, see Connect ALD (RET) Cable on page
25.
5. Connect the external alarm cable, see Connect External Alarm Cable on
page 26.
A B C D
M N O P
1 2
J
E
F K L G H I
Ge12249D
B Antenna B
C Antenna C
C
D Antenna D
D
E Maintenance button – – –
F Optical indicators – –
, ,
1, 2
G Optical cable 1 1 LC (On SFP) with
support for FullAXS
H Optical cable 2 2
J Grounding 2 x M6 bolt
N (1) TX monitor B
O (1) TX monitor C
C
P (1) TX monitor D
D
(1) Optional for B3 and B7.
Note: Always connect the grounding cable before connecting any other
cable.
Do!
Steps
or
10 mm
8 Nm
Ge7577F
Warning!
High energy levels are present in this unit. Improper handling of the unit can lead to
short circuits that can result in serious injury. Exercise care when working with this
unit.
Steps
1.
A B
Ge6736D
Ge6244C
Steps
Ge1722C
Ge1723C
Ge4711A
Ge5799B
6. 1
Clamp the plug body with the
seal ring to the optical cable.
Ge5792C
Ge5802D
Ge5793C
Steps
Ge6733B
Steps
Ge6733B
• White conductor
• Blue conductor
Alarm B
Alarm A Alarm B
• Turquoise conductor
• Violet conductor
Steps
5 Nm
Ge7786C
Steps
Ge7840C
0.23 Nm
Ge7733E
Ge7952A
This section describes the verification that must be performed to check the
installation of the radio and the connections to the main unit before it is
integrated with the radio network.
(1) Ensure that the minimum bending radius is not violated. For more information, refer to
Installing Optical Cables for Main-Remote Solutions.
Use the checklist in Table 8 to check the installation and grounding of power
system equipment.
Do!
Steps
Ge7355E
ON
OFF
Ge6816B
For more information on interpreting the optical indicators on the radio, refer to
Indicators, Buttons, and Switches.
Steps
Ge7615B
Ge5649C
1. Clean the site and remove objects such as wrapping paper and cable
clippings.
Hazardou
s
Plastic
Metal
Paper
Ge8582A
5. Hand over the Customer Site Documentation to the person responsible for
the site.
9 References
Safety
124 46-2885
124 46-2886
Generic
• Install Rail
• Radio Description
• Seal Connectors