Professional Documents
Culture Documents
Fabco 115
Fabco 115
FabCO115
DESCRIPTION: FabCO 115 is a high-strength, flux-cored wire that is comparable to a low alloy E11018M electrode but with higher
deposition rates. It is used primarily for welding A514, A517, HY100 and similar quenched and tempered high-strength, low alloy steels, producing a low hydrogen deposit with basic slag which helps to minimize cracking. FabCO 115 has high impact values at low temperatures and provides you with a modified globular metal transfer. For use with 100% CO2 shielding gas only.
APPLICATIONS:
Mining equipment, earthmoving equipment and off-the-road vehicles.
FEATURES:
Higher deposition rate than 11018M stick electrode Basic slag system 2% nickel content welds at low temperatures
BENEFITS:
Increases productivity Minimizes the possibility of cracking Provides increased weld toughness for critical
SHIELDING GAS: 100% CO2 TYPE OF CURRENT: DCEP TYPICAL WELD METAL PROPERTIES*(Chem Pad):
Weld Metal Analysis 100% CO2
Carbon (C) Manganese (Mn) Silicon (S) Phosphorus (P) Sulphur (S) Chromium (Cr) Nickel (Ni) Molybdenum (Mo)
Hobart Brothers Company 400 Trade Square East Troy, OH 45373 PH: (800) 424-1543 FX: 800-541-6607 www.hobartbrothers.com
FabCO115
WELDING DATA:
The information listed below was determined using 100% CO2 shielding gas with flow range between 35 to 40 cubic feet per hour. Welding was performed in position designated below with DCEP welding current.
Optimum Welding Parameters Wire Feed Speed In/Min Deposition Rate lbs/hr
Diameter inches mm
Weld Position
Amps
Volts
Stickout 1/4
.045 .045 .045 1/16 1/16 1/16 1/16 3/32 3/32 3/32 3/32 3/32 3/32 CAUTION:
1.2 1.2 1.2 1.6 1.6 1.6 1.6 2.4 2.4 2.4 2.4 2.4 2.4 * * *
Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal Flat, Horizontal
120 170 220 190 240 290 350 290 325 375 425 475 525
22.0 24.0 27.0 22.0 24.0 26.0 30.0 25.0 26.0 27.0 28.0 30.0 32.0
160 254 359 117 155 204 265 103 116 136 159 195 218
3.1 4.6 6.4 4.3 6.0 7.0 8.6 8.5 9.5 11.3 13.2 17.3 19.1
Consumers should be thoroughly familiar with the safety precautions shown on the warning label posted in each shipment and in the American National Standards Z49.1, Safety in Welding and Cutting, published by the American Welding Society, 550 NW LeJeune Road, Miami, Florida 33126; OSHA Safety and Health Standards 29 CFR 1910 is available from the U.S. Department of Labor, Washington, D.C. 20210.
Material Safety Data Sheets on any Hobart Brothers Company product may be obtained from Hobart Customer Service. Because Hobart Brothers Company is constantly improving products, Hobart reserves the right to change design and/or specifications without notice. FabCO is a registered trademark of Hobart Brothers Company, Troy, Ohio.