Professional Documents
Culture Documents
Selection of Couplings
Selection of Couplings
Resilient
and
Soft
Start
Couplings
5th Edition
Products: Shaft Couplings, Resilient Gear and Fluid Soft-Start, Clutches: Sprag and Trapped Roller Freewheels, Slipping and Air Types.
Gears
Holroyd Gears Works, Milnrow, Rochdale OL16 3LS England Tel: Fax: E-Mail: Web: +44 (0) 1706 751000 +44 (0) 1706 751001 sales@gears.renold.com www.renold.com
Products: Worm, Helical and Bevel-Helical Speed Reducer Gear Units, Geared Motor Units and Fully Engineered Drive Packages.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
Contents
Page No Company Profile Typical Applications Pictorial Contents Gear Division Product Range Coupling Selection Guide Selections Taper Bushes Spiderflex Spider Pinflex Crownpin Tyreflex Discflex Chainflex Rigid Gearflex Hydrastart Electric Motor Shaft Dimensions Renold Hi-Tec Coupling Range Renold Worldwide Sales & Services 5 6-7 8-9 10 11 12 - 15 16 17 - 19 20 21 - 25 26 - 28 29 - 32 33 - 35 36 - 37 38 39 - 47 49 - 61 55 62 - 92 94 - 95
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
3
WORM GEARS
HELICAL GEARS
VARIABLE SPEED
FLEXIBLE COUPLINGS
SPRAG CLUTCHES
INDEXERS
Renolds Quality is inherent across its range of power transmission products, allowing you to select for individual applications or combined engineered package solutions. Select Renold to keep your plant running and design options open.
Consistent Reliability
Renolds 100 years of experience in the design and manufacturing of power transmission products to the highest specifications, with proven performance in diverse industries world-wide, underwrites the guaranteed quality and the assurance of reliability. Renold Clutches & Couplings is BS EN ISO 9001:2000 approved. All products are designed and manufactured to this Quality Assurance System.
LRQO/881495
Certificate 9079
Testing
Although each of our factories manufacturing and testing demands vary, the following capabilities are available if the application demands it: Full scale radial and axial stiffness measurement. Torsional vibration analysis. Misalignment testing of couplings up to 2 metres diameter. Measurements of torsional stiffness up to 220 KNM Static and dynamic balancing capabilities. Noise attenuation testing. Transient and finite element analysis.
The organisation stretches worldwide 16 National Sales Companies Over 70 Overseas Distributors Offering the comprehensive range of power transmission products directly or through local distributor networks
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
5
Pinflex
A robust general purpose pin/buffer coupling, providing reliable fail safe transmission of torque and misalignment capability. G Pumps G Compressors G Conveyors
Crown Pin
An established pin/buffer coupling offering extended power capacity where the demand for long life and simplicity of construction make it suitable for working in arduous conditions. G Conveyors G Washers G Pumps G Screens G Cranes G General Industrial Application
Spider Couplings
Relatively low power but highly flexible coupling with halfbodies in either cast iron or bronze, making suitable for use in the food or chemical/pharmaceutical industries. G Pumps G Mixers G Lube Systems
L
6
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
L Gearflex
Heavy duty all metal couplings giving maximum power capacity within minimum space envelope and excellent misalignment capacity. G Steelworks G Quarries G Mining
L Tyreflex
A range of highly flexible couplings offering excellent misalignment capacity and suitable to absorb both shock loads and vibrations. G Pumps G Compressors G Diesel Engines G Roller Tables
L Spiderflex
A medium powered, torsionally flexible coupling, combining shock absorbing and misalignment. Used in the widest range of industries and applications.
L RB
0.24 RB flywheel mounted coupling on a Deutz TD 229 - 6 diesel generator set in Spain. G Generator Sets G Pump Sets G Compressors G Bulk Handling
PM
G Metal Manufacturing G Pumps G Fans G Compressors G Pulp and Paper G Cranes and hoists
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
7
Pictorial Contents
Spiderflex Coupling Spider Coupling
Pinflex Coupling
Tyreflex Coupling
Discflex Coupling
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
8
Pictorial Contents
Chainflex Coupling Rigid Coupling
Taper Bushes
125mm 16
50485 4747000 Nm 39
RB & PM Couplings
6000KNm 64 and 76
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
9
HC Series
Helical and bevel/helical units available in 14 sizes up to 1000kW. Heavy duty design for high torque applications. Gear case hardened and ground for high efficiency and quiet running. Hollow and solid shaft variants allow design options. G G G
RP Series
In-line helical speed reducers and geared motor units available in single, double and triple reduction types from 0.25kW to 45kW with ratios from 1:5:1 to 100:1. Designed to European standard, therefore interchangeable without re-engineering. Foot and flange mounting for flexibility in applications. Standard heavy-duty version for higher load characteristics.
G G G G G
L L
G G G
Shaft mounted speed reducers available as single reduction units with 5:1 ratios and double units with ratios of 13:1, 20:1, 25:1 metric and 15:1 North American. Interchangeable to allow fast and easy replacement. Robust construction ideal for heavy-duty applications. Wide ratio range gives competitive size selections. Parallel and taper bore options allow easy removal for repair. Sprag clutch backstop available to prevent drive reversal. Enhance seal arrangements for use in hostile environments.
G G G G G G
Available as digital control and as a multi parameter facility covering most of the control requirements, with a power range of 0.37kW to 55kW.
Helical/Bevel/Helical unit with high gear ratio and large torque range up to 12000 Nm. Available as speed reducer or motorised versions. Ratios from 20:1 to 160:1. Robust case and gear construction allowing use in heavy duty applications.
L
G G G
Carter Variator
Hydrostatic variable speed drives with a 27:1 speed range and capacities up to 22kW. Proven reliability in hazardous environments. Accurate speed holding. High starting torque (200% FLT). Built in overload protection.
WM Series
L
WM Series is available with 4 - 9 centres and ratios of 5:1 to 70:1 as a single reduction unit and 75:1 to 4900:1 as a double reduction. Foot, flange and shaft mounted types available. Heavy duty version for demanding applications. Unique Holroyd tooth form for high efficiency and product life. Integral sprag clutch holdback for safe running.
G G G G
G G G
Variable speed range of up to 8.75:1 and a power capacity up to 110kW. Suitable for operating in most hostile and explosion proof areas. Available with universal mounting to allow design flexibility.
G G
TW Series
L
Heavy duty worm units with centres from 10 to 28 in single and reduction types. Ratios available from 5:1 to 4900:1 with input powers from 16 to 506kW. Heavy duty design for high torque applications. Unique Holroyd tooth form for high efficiency and product life. Optional protection for use in hostile and arduous environments.
G G G
Disc variable speed drive unit with 5:1 speed range and up to 4kW power capacity. Excellent speed holding characteristics under full load conditions. Variable mounting options allow design flexibility.
G G
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
10
NO
Torsionally Flexible
YES
NO
Gearflex Chainflex
Torsionally Flexible
NO
Gearflex Chainflex
YES
YES
NO
Torsionally Flexible
YES
NO
Gearflex Chainflex
Torsionally Flexible
YES NO
Gearflex Chainflex
Torsionally Flexible
YES
NO
Gearflex Chainflex
Torsionally Flexible
YES NO
Gearflex Chainflex
Pinflex Crownpin RB PM
Gearflex Chainflex RB PM
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
11
Selection of Couplings
Flexible Couplings should be used to accommodate any combination of misalignment conditions described below. At installation all couplings should be aligned as near to perfect as possible.
Selection
In order to select the correct type and size of coupling, the following basic information should be known: Power to be transmitted (a) Normal. (b) Maximum. (c) Whether continuous or intermittent. Characteristics of the drive (a) Type of prime mover and associated equipment. (b) Degree of impulsiveness of driven load. Speed in revolutions per minute (a) At which normal power is transmitted. (b) At which maximum power is transmitted. (c) Maximum speed. Dimensions of shafts to be connected (a) Actual diameter. (b) Length of shaft extension. (c) Full keyway particulars.
1. Angular
Angular misalignment is present when the shaft axes are inclined one to the other. Its magnitude can be measured at the coupling faces.
2. Parallel Offset
O
Axial misalignment is present when the axes of the driving and driven shafts are parallel but laterally displaced.
Selection
When the input drive is not steady (i.e. not from an electric motor), and/or the driven load is impulsive, the actual power is multiplied by a Service Factor from the Table 2 (page 14).
Selection Procedure
1.
Nominal power in kW to be transmitted = K. Select appropriate load classification from Table 1, denoted as either S, M or H. From Table 2, establish Service Factor(s) to be applied, taking into account hours of operation/day and prime mover = fD. From Table 3 select factor for the required frequency of starts/hr = fS. Selection Power Ks = K x fD x fS Equivalent power at 100 RPM = Ks x 100 RPM Check that coupling selected will accept the required shaft diameters. Should shaft diameter exceed maximum permissible, then re-select using next larger size of coupling.
2. 3. 4.
End float is the ability to accommodate a relative axial displacement of the connected shafts; achieved by sliding members or flexing of resilient components.
4. Torsional flexibility
5. 6.
7. Torsional flexibility is a design feature necessary to permit shock and impulsive loadings to be suitably dampened. It is achieved by the provision of a flexible medium such as rubber, springs, etc., between the two halves of the coupling.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
12
Conveyors - uniformly loaded or fed Apron S Assembly S Belt S Bucket S Chain S Flight S Oven S Screw S Conveyors - heavy duty not uniformly fed Apron M Assembly M Belt M Bucket M Chain M Flight M Live roll * Oven M Reciprocating H Screw M Shaker H Crane Drives - not dry dock Main hoists S Bridge travel * Trolley travel * Crushers Ore H Stone H Sugar (1) M Dredges Cable reels M Conveyors M Cutter head drives H Jig drives H Manoeuvring winches M Pumps M Screen drive H Stackers M Utility winches M Dry dock cranes Main hoist (2)
S = Steady M = Medium Impulsive H = Highly Impulsive * = Refer to Renold (1) = Select on 24 hours per day service factor only. (2) = Use service factor of 1.00 for any duration of service. (3) = Use service factor of 1.25 for any duration of service. (4) = Use service factor of 1.50 for any duration of service.
Note
Machinery characteristics and service factors listed in this catalogue are a guide only. Some applications (e.g. constant power) may require special considerations. Consult Renold.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
13
Electric, Air & IntermittentHydraulic Motors 3hrs/day max or Steam Turbine 3 - 10 (Steady input) over 10 Multi-cylinder I.C. Intermittentengine (Medium 3hrs/day max impulsive input) 3 - 10 over 10 Single-cylinder IntermittentI.C. engine 3hrs/day max (Highly impulsive 3 - 10 input) over 10
Note
For applications with excessive vibration, contact Renold Technical Department.
Example Of Selection
Coupling is required to transmit 7.5kW at 1440 RPM to connect an electric motor to a gear box driving a chain conveyor running for 18 hours/day and starting 15 times/hour. Shaft diameters /55mm respectively. K = 7.5kW From Table 1 Load Classification = M (medium impulsive) From Table 2 Service Factor fD = 1.5 From Table 3 fS = 1.2 Therefore selection kW is:Ks = K x fD x fS = 7.5 x 1.5 x 1.2 = 13.5 kW Equivalent power at 100RPM = Ks x 100 RPM 13.5 x 100 1440
Key Stress
1. Permissible key stress = 70N/mm2 2. Nominal torque TKM = k x 9550 / RPM Nm 3. Force at key F = TKM /r 4. Shaft Rad r. metres 5. Key area A = J x HUB length mm 6. Key stress fk = F/A N/mm2 7. If resultant stress is less than 70 N/mm2 Key stress is acceptable. If resultant fk is greater than 70, consider either two keyways or extending hub length. 8. Example: TKM = 7.5 x 9550/1440 = 49.7Nm r F A fk = 55/2 = 27.5mm 1000 = 0.0275M = 49.7/0.0275 = 1741N = 16 x 45 = 720mm2 = 1741/720 = 2.4M/mm2 (Obtain from relevant catalogue page).
= 0.9375kW @ 100RPM From page 16 selection is RSC110 (644911) (maximum bore 55 mm).
For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. It is the responsibility of the system designer to ensure that the application of the coupling does not endanger the other constituent components in the system. Service factors given are an initial selection guide. Rotating equipment must be provided with a suitable guard before operating or injury may result.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
14
Metric (mm)
Keyways comply with BS4235: Part 1: 1972 Shaft dia. Over 6 8 10 12 17 22 30 38 44 50 58 65 75 85 95 110 130 150 170 200 Incl. 8 10 12 17 22 30 38 44 50 58 65 75 85 95 110 130 150 170 200 230 J 2 3 4 5 6 8 10 12 14 16 18 20 22 25 28 32 36 40 45 50 Key & Keyway K 2 3 4 5 6 7 8 8 9 10 11 12 14 14 16 18 20 22 25 28 L 1.0 1.4 1.8 2.3 2.8 3.3 3.3 3.3 3.8 4.3 4.4 4.9 5.4 5.4 6.4 7.4 8.4 9.4 10.4 11.4
Keyway dimensions
Parallel keyways are supplied unless customer states otherwise.
Imperial (inches)
Keyways comply with BS46: Part 1: 1958 Shaft dia. Over 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.50 3.00 3.50 4.00 5.00 Incl. 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.50 3.00 3.50 4.00 5.00 6.00 J 0.125 0.187 0.250 0.312 0.375 0.437 0.500 0.625 0.750 0.875 1.000 1.250 1.500 Key & Keyway K 0.125 0.187 0.250 0.250 0.250 0.312 0.312 0.437 0.500 0.625 0.750 0.875 1.000 L 0.060 0.088 0.115 0.090 0.085 0.112 0.108 0.162 0.185 0.245 0.293 0.340 0.384
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
15
Metric Range
Bush No. TB 1008 TB 1108 TB 1210 TB 1215 TB 1610 TB 1615 TB 2012 TB 2017 TB 2517 TB 2525 TB 3020 TB 3030 TB 3525 TB 3535 TB 4030 TB 4040 TB 4535 TB 5050 9 9 11 11 14 14 14 18 16 19 25 35 35 35 40 40 55 70 10 10 12 12 16 16 16 19 18 20 28 38 38 38 42 42 60 75 11 14 14 18 18 18 20 19 22 30 40 40 40 45 45 65 80 12 12 16 16 19 19 19 22 20 24 32 42 42 42 48 48 70 85 14 14 18 18 20 20 20 24 22 25 35 45 45 45 50 50 75 90 16 15 19 19 22 22 22 25 24 28 38 48 48 48 55 55 80 95 18 16 20 20 24 24 24 28 25 30 40 50 50 50 60 60 85 100 Range of Bores (mm) 19 18 22 22 25 25 25 30 28 32 42 55 55 55 65 65 90 105 20 19 24 24 28 28 28 32 30 35 45 60 60 60 70 70 95 110 22 20 25 25 30 30 30 35 32 38 48 65 65 65 75 75 100 115 24* 22 28* 28 32 32 32 38 35 40 50 70 70 70 80 80 105 120 25* 24 30* 30 35 35 35 40 38 42 55 75 75 75 85 85 110 125 25 32* 32* 38 38 38 42 40 45 60 80 80 90 90 115 28*
40 40* 40 45 42 48 65 85 85 95 95 120
44 50* 48 55 75 95
45 50 60
48 55
50 60
100*
Imperial Range
Bush No. TB1008 TB 1108 TB 1210 TB 1215 TB 1610 TB 1615 TB 2012 TB 2017 TB 2517 TB 2525 TB 3020 TB 3030 TB 3525 TB 3535 TB 4030 TB 4040 TB 4535 TB 5050 0.375 0.375 0.50 0.50 0.50 0.75 0.75 1.25 1.50 1.50 1.75 1.75 2.25 2.75 0.437 0.50 0.50 0.50 0.625 0.812 0.875 1.625 1.625 1.875 1.875 2.375 2.875 0.50 0.625 0.562 0.625 0.625 0.75 0.875 1.00 1.375 1.375 1.75 1.75 2.00 2.00 2.50 3.00 0.625 0.75 1.00* 0.75 0.875 1.00 0.625 0.75 0.625 0.75 0.75 0.75 0.875 1.00 0.937 1.00 1.00 1.125 1.125 1.50 1.625 1.50 1.625 1.875 2.00 2.125 1.875 2.00 2.125 2.125 2.25 2.375 2.125 2.25 2.375 2.625 2.75 2.875 3.25 3.375 3.50 1.125* 0.875 0.875 1.125 1.125 1.25 1.75 1.75 2.25 2.25 2.50 2.50 3.00 3.75 Range of Bores (inches)
1.00 0.875 1.00 1.00 1.00 1.25 1.25 1.25 1.375 1.375 1.875 2.00 2.125 1.875 2.00 2.125 2.375 2.50 2.625 2.375 2.50 2.625 2.625 2.75 2.875 2.625 2.75 2.875 3.125 3.25 3.375 4.00 4.25 4.50
1.25 1.125 1.125 1.25 1.50 1.625 1.125 1.25 1.375 1.437 1.50 1.625* 1.375 1.50 1.625 1.75 1.87 2.0 1.375 1.50 1.625 1.75 1.875 2.00 1.437 1.625 1.75 1.875 2.00 2.125 2.25 2.375* 2.50 1.50 1.75 1.875 2.00 2.125 2.25 2.375* 2.50* 2.25 2.50 2.625 2.75 2.875 3.00 2.25 2.50 2.625 2.75 2.875 3.00 2.75 3.00 3.125 3.25 3.50 3.75* 4.00* 2.75 3.00 3.125 3.25 3.50 3.00 3.125 3.25 3.375 3.50 3.00 3.25 3.375 3.50 3.625 3.75* 4.00 3.50 3.75 4.00 4.25 4.50 4.75 5.00* 5.00
*Shallow key Depth. N.B.When ordering specify both bush number and bore size required.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
16
Spiderflex
A medium power torsionally flexible coupling combining shock absorbing and misalignment capacity, used in the widest range of industries and applications. Coupling Capacity: G G Maximum power @ 100RPM Maximum torque 33kW 3150Nm Standard Range Comprise: G G G Shaft to Shaft Flywheel to Shaft Taper Bush or Parallel Bore
Features & Benefits: G G G G G G G G Torsionally flexible - shock absorbing, extending machine life. Maintenance free - minimum number of wearing parts. Misalignment capabilities allowing flexibility in installation. Cost effective - offering a low cost product with high quality design. Dimensionally similar to other spider couplings - interchangeable. Optional fire retardent anti-static elements for use in flameproof environment. Taper bush bores available for ease of maintenance. Compact design - small, with high torque capacity.
Applications: G G G G G G Bulk Handling Compressors Generator Sets Metal Manufacture Pumps General Industrial Applications
Construction Details: Cast Iron Half Bodies Grade G220 Standard Element Shore Harness A90 Temp Range -30 + 100C F.R.A.S. Element Shore Harness A78 Temp Range -30 + 95C
Spiderflex
G H1 H2 H2
Assembled length
C1
C2
C2
F L
Type B
Type F
Type H
Coupling Size RSC70 # # # RSC90 # # # RSC110 # # # RSC130 # # # RSC150 # # # RSC180 # # # RSC230 # # # RSC280 # # #
Speed Max rpm 7700 6300 5000 4100 3600 3000 2600 2200
Type F & H Bush Size TB1008 TB1108 TB1610 TB1610 TB2012 TB2517 TB3020 TB3525 Bore Max Min 25 28 42 42 50 65 75 90 9 9 14 14 14 16 25 35
Max. Misalignment Offset mm 0.3 0.3 0.3 0.4 0.4 0.4 0.5 0.5 Angular deg 0.5 0.5 1 1 1.5 1.5 2 2.5
End Float mm +.2 +.5 +.6 +.8 +.9 +1.1 +1.3 +1.7
Coupling Size RSC70 # # # RSC90 # # # RSC110 # # # RSC130 # # # RSC150 # # # RSC180 # # # RSC230 # # # RSC280 # # # B mm 61 70 100 105 115 125 155 206 C1 mm 23.5 30.0 45.0 55.5 60.0 70.0 90.0 105.5 C2 mm 23.5 23.5 26.5 26.5 33.5 46.5 52.5 66.5 D mm 69 85 112 139 150 180 225 275
Dimensions E mm 31 32 45 50 62 77 99 119 F mm 18 22.5 29 36 40 49 59.5 74.5 G mm 25 30.5 45 53 60 73 85.5 105.5 H1 mm 20 26 37 47 50 58 77 90 H2 mm 20.0 19.5 18.5 18.0 23.5 34.5 39.5 51.0
Assembled Overall Length L With Half Body Combinations:BB FF, FH, HH FB, HB 65 83 119 147 160 189 240 285 65 70 82 89 107 142 164 207 65 77 101 118 134 166 202 246
1. At speeds exceeding allowable maximum speed, consult Renold. 2. Both moment of inertia and coupling weight have been calculated assuming fitting of taper bush of medium bore size. 3. For information on torsional stiffness, consult Renold.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
18
Spiderflex
Coupling Size RSC70 RSC90 RSC110 RSC130 RSC150 RSC180 RSC230 RSC280 Coupling Mass Kg 1.00 1.17 5.00 5.46 7.11 16.60 26.00 50.00 Coupling Inertia WR 2 Type B Type F&H Kg m2 Kg m2 0.00078 0.00108 0.00344 0.00850 0.02112 0.04820 0.14052 0.54790 0.00085 0.00115 0.00400 0.00780 0.01810 0.04340 0.12068 0.44653
Ordering Code
Spiderflex Size Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush
RSC 70 # # # Element Material S - Standard X - F.R.A.S. Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush
Specials available, e.g. Shear Pin, Extended Boss, Flywheel Flange, Spacer. Contact Renold for details.
Component Spares
Spider Flexible Element RSC70 EL RSC90 EL RSC110 EL RSC130 EL RSC150 EL RSC180 EL RSC230 EL RSC280 EL Half Body Unbored Type B RSC70 B RSC90 B RSC110 B RSC130 B RSC150 B RSC180 B RSC230 B RSC280 B Half Body Taper Bored Type F RSC70 F RSC90 F RSC110 F RSC130 F RSC150 F RSC180 F RSC230 F RSC280 F Half Body Taper Bored Type H RSC70 H RSC90 H RSC110 H RSC130 H RSC150 H RSC180 H RSC230 H RSC280 H
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
19
Spider
F
Coupling Number S11C S11B S15C S15B S21C S21B S30C S30B S37C S37B
Power /100rpm Kw 0.025 0.025 0.061 0.061 0.28 0.28 0.56 0.56 1.12 1.12
Torque Nominal Nm 2.39 2.39 5.83 5.83 26.74 26.74 53.5 53.5 107 107
Speed Max rpm 11000 11000 6500 6500 4800 4800 4800 4800 3500 3500 Max mm 14 12 20 20 25 25 30 30 42 42
Bore A Min mm 0 0 0 0 0 0 0 0 0 0
Dimensions Misalignment B C* D F Mass Angular Offset Max Max mm mm mm mm kg degrees mm 28 28 38 38 48 48 57 57 83 83 12 12 14 14 21 21 27 27 36 36 28 28 38 38 55 55 78 78 95 95 8.8 8.8 0.12 0.13 1 1 1 1 1 1 1 1 1 1 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25
End Float mm 0.25 0.25 0.38 0.38 0.51 0.51 0.76 0.76 0.89 0.89
11.8 0.26 11.8 0.27 16.2 0.68 16.2 0.70 22.9 1.57 22.9 1.63 26.2 3.53 26.2 3.66
Component Spares
Coupling Number S11C S11B S15C S15B S21C S21B S30C S30B S37C S37B Spider Flexible Element S11 S11 S15 S15 S21 S21 S30 S30 S37 S37 Half Body Pilot Bored 644826 644838 644827 644839 644828 N/A 644829 N/A 644830 N/A Half Body Solid Boss Unbored 644846 644842 644847 644843 644848 N/A 644849 N/A 644850 N/A
Ordering Code
S 15 # Spider Size Half Body Material C - Cast Iron B - Aluminium Bronze
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
20
Pinflex
A robust, general purpose pin/buffer coupling providing reliable fail safe transmission of torque and misalignment capability. Coupling Capacity: G G Maximum power @ 100RPM Maximum torque 340kW 32500Nm Standard Range Comprise: G G G Shaft to Shaft Shear Pin Brake Drum/Disc
Features & Benefits: G G G G G G G G G Steel half bodies, strong yet compact. Heavy duty pin and buffer coupling - for heavy shock load conditions. Torsionally flexible - shock absorbing, extending machine life. Maintenance free - minimum number of wearing parts. Misalignment capabilities allowing flexibility in installation. Steel Half Bodies. Polyureathane buffers, reliable/flexible and temperature resistant. Modular construction - available as coupling, brakedrum and shear pin designs. Taper bores available for ease of maintenance.
Construction Details: Steel Half Bodies Urethane Buffer: Temp Range - 40C to + 80C
Pinflex
E F
C1
C2
C2
Type B
Catalogue Number PF1# #3 PF1# #6 PF1BB9 PF1BB12 PF2# #3 PF2# #6 PF2BB9 PF2BB12 PF3# #3 PF3# #6 PF3BB9 PF3BB12 PF4# #3 PF4# #6 PF4BB9 PF4BB12 PF5# #4 PF5# #8 PF5# #12 PF5BB16 PF6# #3 PF6# #6 PF6# #9 PF6BB12 PF7# #4 PF7# #8 PF7# #12 PF7BB16 PF8# #4 PF8# #8 PF8# #12 PF8BB16 PF9BB4 PF9BB8 PF9BB12 PF9BB16 Power Torque Speed Type B
Type F
Type F & H
Type H
Dimensions
Type F & H
/100rpm Nominal Max Kw Nm rpm 2.03 4.05 6.08 8.1 3.59 7.18 10.76 14.35 4.24 8.48 12.71 16.96 8.32 16.65 24.97 33.29 13.94 27.88 41.82 55.76 24.70 49.40 74.10 98.80 37.18 74.35 111.53 148.70 64.70 129.40 194.10 258.80 85.00 170.00 255.00 340.00 194 387 581 774 343 685 1028 1370 405 810 1214 1620 795 1590 2384 3179 1331 2662 3994 5325 2359 4717 7076 9435 3550 7100 10650 14200 6179 12357 18536 24714 8130 16255 24385 32500 6800
Bore Bush Bore B C1 C2 D E F Mass* WR * Mass* WR2* kg kg m2 Max Min Size Max Min mm mm mm mm mm mm kg kg m2 50 0 TB1215 32 11 70 44 40 125 20 4 5.2 0.00828 5.0 0.00813
5900
55
TB1615 42
14
80
50
40 145 25
8.3
0.01843
7.6
0.01780
5200
72
TB2017 50
18 100 60
47 165 25
13.8
0.03335
12.1
0.03143
4400
80
TB2525 60
19 113 75
65 195 35
22.0
0.08470
20.3
0.08195
3600
110
TB3030 75
35 150 89
80 235 35
37.8
0.19972
35.3
0.19274
2900
130
55 TB3535 90
73.2
0.61140
65.2
0.58086
2600
150
65 TB4040 100
103.0 0.99756
88.5
0.92310
2200
175
75 TB5050 125
1700
260
75
N/A
N/A
490 60
423.0 9.19000
N/A
N/A
NOTE: Maximum power and torques for taper bore options are limited by the taper bush capacity. * Values are for couplings with no bore and a full set of pin assemblies. Max angular misalignment 0.25 Disc Brake Drum version also available - consult Renold for details. Max axial misalignment 0.13mm
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
22
Pinflex
Ordering Code
Pinflex Size Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush PF 3 # # 9 No of Pins Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush
Component Spares
Coupling Size PF1 PF2 PF3 PF4 PF5 PF6 PF7 PF8 PF9 Half Body Pilot Bored PF1 B PF2 B PF3 B PF4 B PF5 B PF6 B PF7 B PF8 B PF9 B Half Body Taper Bored Type F PF1 F PF2 F PF3 F PF4 F PF5 F PF6 F PF7 F PF8 F N/A Half Body Taper Bored Type H PF1 H PF2 H PF3 H PF4 H PF5 H PF6 H PF7 H PF8 H N/A Pin and Buffer Set Part Number Number Per Set PF A PF B PF B PF C PF C PF D PF D PF E PF E 3 3 3 1 1 1 1 1 1 Coupling Size PF1 PF2 PF3 PF4 PF5 PF6 PF7 PF8 PF9
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
23
B1 A1
A2
B2
C1 F
C2
Coupling Size
Power /100rpm Kw
Torque Nominal Nm 774 1370 1620 3179 5325 9435 14200 24714
Speed Max rpm 3600 2850 2300 1900 1400 1400 1100 900 Dimensions A1 Max mm 50 55 72 80 110 130 150 175
Bore A2 Max mm 45 50 60 75 90 110 130 150 Dia E mm 160 200 250 315 400 400 500 630
Drum Dimensions Width G mm 92 105 124 140 184 184 241 267 No. of Dia E inch 6 8 10 12 16 16 20 24
PFBD1 # PFBD2 # PFBD3 # PFBD4 # PFBD5 # PFBD6 # PFBD7 # PFBD8 # Coupling Size PFBD1 # PFBD2 # PFBD3 # PFBD4 # PFBD5 # PFBD6 # PFBD7 # PFBD8 # B1 mm 70 80 100 113 150 180 210 245
Pin & Buffer Set Part No. PFA PFB PFB PFC PFC PFD PFD PFE No. Per Set 3 3 3 1 1 1 1 1
F mm 4 5 5 6 6 7 7 7 PF BD 5 #
H mm 22 13 20
WR kg m2
2
Ordering Code
Pinflex Brake Drum Size
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
24
A2
A1
Coupling Size PFS1 # PFS2 # PFS3 # PFS4 # PFS5 # PFS6 # PFS7 # PFS8 # PFS9 #
Nominal Torque Nm 387 685 810 1590 2662 4717 7100 12357 16255
Shear Torque Speed Min Nm 194 220 350 425 520 1100 2750 5900 8130 Max Nm 774 1370 1620 3180 5324 9434 14200 24714 32510 Max rpm 6800 5900 5200 4400 3600 2900 2600 2200 1700
Bore A2 Max mm 40 47 57 63 93 107 120 147 200 Min mm 55 65 75 75 B mm 70 80 100 113 150 180 210 245 355 C mm 44 50 60 75 89 110 130 150 220
Dimensions D mm 125 145 165 195 235 290 320 380 490 E mm 20 25 25 35 35 50 50 60 60 F mm 4 5 5 6 6 7 7 7 7 Mass kg 6.3 10.1 15.3 27.3 47.3 89.8 129 212 513
No. of Pins 6 6 6 6 8 6 8 8 8
Ordering Code
Pinflex Shear Pin Size
Select coupling based on nominal torque using service factors from page 14. Then select required shear torque from table above.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
25
Crownpin
An established pin/buffer coupling, offering extended power capacity where the demand for long life and simplicity of construction make it suitable for working in arduous conditions. Coupling Capacity: G G Maximum power @ 100RPM Maximum torque 2611kW 249400Nm Applications: G G G G G G G G G Conveyors Cranes Fans Leisure Rides Lifts Pumps Screens Washers General Industrial Applications
Features & Benefits: G G G G G Heavy duty coupling suitable for shock load conditions. Neoprene rubber buffers for robust flexibility. Torsionally flexible - shock absorbing, extending machine life. Maintenance free - minimum number of wearing parts. Misalignment capabilities allowing flexibility installation.
Construction Details: Cast Iron Half Bodies Neoprene Buffers: Temp range - 30 to + 95c
Crownpin
F PIN HALF E G BUFFER HALF
Type B
Coupling Number CP36BB3 CP48BB4 CP48BB8 CP57# #4 CP57# #8 CP65# #8 CP77# #8 CP91# #4 CP91# #8 CP106# #10 CP120# #8 CP135# #10 CP150BB10 CP165BB10 CP180BB10 CP210BB12 CP240BB12 CP270BB14 CP300BB14 CP360BB18 CP420BB16 CP480BB20 Power
C1
C1
C2
C2
Type F
No Mass kg 1.9 3.7 3.7 6.6 6.6 10 15 30 30 45 63 90 130 168 218 295 450 587 825 1160 1700 2250 of Pins 3 4 8 4 8 8 8 4 8 10 8 10 10 10 10 12 12 14 14 18 16 20 Spare Parts Code A A A B B C D E E E F F G G H H K K L L M M
Torque Speed
Type B
Type F
Dimensions
/100rpm Nominal Max Kw Nm rpm 0.37 0.74 1.48 1.85 3.7 5.21 7.45 10.44 20.9 32.8 41.8 62.7 97 112 164 246 373 496 746 1194 1716 2611 35 71 142 177 354 497 711 997 1995 3134 3990 5984 9262 10690 15660 23490 35620 46990 71240 114000 163900 249400 6210 4760 4760 3980 3980 3520 2950 2510 2510 2510 1900 1690 1520 1380 1270 1090 950 840 760 630 540 470
Bore A Bush Bore B C1 C2 D E F G Max Min Size Max Min mm mm mm mm mm mm mm 20 35 35 45 45 50 65 75 75 90 95 115 120 140 145 150 180 200 230 250 280 300 0 0 0 0 0 0 0 N/A N/A N/A 11 11 14 37 62 62 73 73 83 32 38 38 45 45 51 94 15 2.4 2.4 2.4 2.4 2.4 3.2 3.2 4.8 4.8 4.8 6.4 6.4 6.4 6.4 7.9 7.9 8.7 8.7 9.5 9.5 23 23 23 29 29 35 35 46 46 46 54 54 65 65 71 71 83 83 102 102 122 15 122 15
38 146 19 38 146 19 38 165 22 45 197 22 64 232 29 64 232 29 76 270 29 89 305 33 381 40 419 40 457 48 533 48 609 56 686 56 762 67 914 67
18 103 60 19 121 70 19 121 70 35 156 83 35 165 95 222 121 254 133 267 146 279 172 330 197 368 216 406 229 470 254 482 279 533 305
38 TB2525 60 38 TB2525 60 38 TB3030 75 45 TB3535 90 50 TB4040 100 60 65 70 70 85 85 95 95 110 110 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A -
Ordering Code
Crownpin Size Pin Half Type B - Plain Bore F - Taper Bush
CP 77 # # 8 No of Pins Buffer Half Type B - Plain Bore F - Taper Bush Max angular misalignment 0.15 Max axial misalignment:CP36 to CP135 - 0.13mm CP150 to CP480 - 0.18mm
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
27
Crownpin
Component Spares
Coupling Number CP36BB3 CP48BB4 CP48BB8 CP57##4 CP57##8 CP65##8 CP77##8 CP91##4 CP91##8 CP106##10 CP120##8 CP135##10 CP150BB10 CP165BB10 CP180BB10 CP210BB12 CP240BB12 CP270BB14 CP300BB14 CP360BB18 CP420BB16 CP480BB20 Product Number 7032303 7032105 7032305 7032106 7032306 7032307 7032308 7032109 7032309 7032310 7032312 7032313 7032315 7032316 7032318 7032321 7032324 7032327 7032330 7032336 7032342 7032348 Pin Half Body Pilot Bored Taper Bored 7032303/1 7032105/1 7032305/1 7032106/1 7032306/1 7032307/1 7032308/1 7032109/1 7032309/1 7032310/1 7032312/1 7032313/1 7032315/1 7032316/1 7032318/1 7032321/1 7032324/1 7032327/1 7032330/1 7032336/1 7032342/1 7032348/1 N/A N/A N/A 7032106/177 7032306/177 7032307/177 7032308/177 7032109/177 7032309/177 7032310/177 7032312/177 7032313/177 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
(continued)
Buffer Half Body Pilot Bored Taper Bored 7032303/2 7032105/2 7032305/2 7032106/2 7032306/2 7032307/2 7032308/2 7032109/2 7032309/2 7032310/2 7032312/2 7032313/2 7032315/2 7032316/2 7032318/2 7032321/2 7032324/2 7032327/2 7032330/2 7032336/2 7032342/2 7032348/2 N/A N/A N/A 7032106/277 7032306/277 7032307/277 7032308/277 7032109/277 7032309/277 7032310/277 7032312/277 7032313/277 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
Pin & Nut 7030003/60 7030003/60 7030003/60 7030006/60 7030006/60 7030007/60 7030008/60 7030009/60 7030009/60 7030009/60 7030012/60 7030012/60 7030015/60 7030015/60 7030018/60 7030018/60 7030024/60 7030024/60 7030030/60 7030030/60 7030042/60 7030042/60
Neoprene Buffer 7030003/3 7030003/3 7030003/3 7030006/3 7030006/3 7030007/3 7030008/3 7030009/3 7030009/3 7030009/3 7030012/3 7030012/3 7030015/3 7030015/3 7030018/3 7030018/3 7030024/3 7030024/3 7030030/3 7030030/3 7030042/3 7030042/3
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
28
A range of highly flexible couplings offering excellent misalignment capacity and suitable to absorb both shock loads and vibrations. Coupling Capacity: G G Maximum power @ 100RPM Maximum torque 65.8 kW 6270 Nm Standard Range Comprise: G G Shaft to Shaft Pump Spacer Type
Features & Benefits: G G G G G G G High misalignment capabilities - high flexibility. Shock absorbing - extending machine life. Maintenance free - minimum number of wearing parts. Fire retardent, anti-static elements available for use in a flameproof environment. Interchangeability means no re-engineering. Pump spacer option for easy pump maintenance. Taper bush bores available for ease of replacement.
Applications: G G G G G Compressors Generator Sets Pumps Roller Table Drives General Industrial Applications
Construction Details: Steel or S.G. Iron Half Bodies Rubber Tyres: Temp Range -50C to + 50C Chloroprene Tyres: Temp Range -15C to + 70C
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
29
Tyreflex
Sizes TY40 to TY60
L1 F C1 F L2 C2 F L3 C3 P F
Type B
Coupling Size TY40 # # TY50 # # TY60 # # TY70 # # TY80 # # TY90 # # TY100 # # TY110 # # TY120 # # TY140 # # TY160 # # TY180 # # Coupling Size TY40 # # TY50 # # TY60 # # TY70 # # TY80 # # TY90 # # TY100 # # TY110 # # TY120 # # TY140 # # TY160 # # TY180 # # C1 mm 22 32 38 35 42 49 56 63 70 94 102 114 Power
Type F
Torque Speed Type B
Type H
Type F
Type B
Type H
Type F
Max. Misalignment Offset mm 1.1 1.3 1.6 1.9 2.1 2.4 2.6 2.9 3.2 3.7 4.2 4.8 Angular deg 4 4 4 4 4 4 4 4 4 4 4 4 Type B End Float mm 1.3 1.7 2.0 2.3 2.6 3.0 3.3 3.7 4.0 4.6 5.3 6.0 Type F Mass* kg 1.05 1.5 2.35 3.45 5 7.25 10 11.7 16.5 22.3 33.5 42.2
Type H
Torsional Stiffness Nm/ 6 12.5 32 60 63 91 126 178 296 470 776 1370 Type H Mass* kg 1.05 1.5 2.35 3.45 5 7.25 10 11.7 15.9 22.3 32.5 42.2
/100rpm Nominal Max Kw Nm rpm 0.26 0.69 1.33 2.62 3.93 5.24 7.07 9.2 13.9 24.3 39.4 65.8 25 66 127 250 375 500 675 875 1300 2320 3770 6270 4500 4500 4000 3600 3100 3000 2600 2300 2050 1800 1600 1500
Bore Bush Bore Bush Bore Max Min Size Max Min Size Max Min 30 38 45 50 60 70 80 95 110 130 140 150 12 TB1008 15 TB1210 18 TB1610 22 TB2012 25 TB2517 28 TB2517 32 TB3020 30 TB3020 25 32 42 50 60 60 75 75 9 TB1008 25 32 42 42 50 60 60 75 75 9 11 14 14 14 16 16 25 25 35 40 55 11 TB1210 14 TB1610 14 TB1610 16 TB2012 16 TB2517 25 TB2517 25 TB3020 35 TB3020
C2 mm 22 25 25 32 45 45 51 51 65 65 77 89
C3 mm 22 25 25 25 32 45 45 51 51 65 77 89
D mm 104 133 165 187 211 235 254 279 314 359 402 470
P mm 29 38 38 38 42 48 48 55 67 67 80 89
Mass* kg 1.05 1.5 2.35 3.45 5 7.25 10 12.5 16.9 22.2 35.8 49.1
NOTE: M is distance by which clamping screws need to be withdrawn to release tyres. P is wrench clearance for taper bush screws when large end is outboard Type H. * Mass is for single hub assembly and half tyre.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
30
R P
M S Y
DBSE
Spacer Shaft Size RSS12 RSS12 RSS16 RSS16 RSS16 RSS16 RSS16 RSS16 RSS25 RSS25 RSS25 RSS25 RSS25 RSS25 RSS25 RSS25 RSS30 RSS30 RSS30 RSS30 RSS35 RSS35 RSS35 RSS35
DBSE
Tyreflex
Tyreflex Cplg.
Dimensions
Nominal Coupling DBSE Range Nm Size Min Max 80 100 100 140 100 140 100 140 100 140 180 100 140 180 140 180 140 180 140 180 140 180 140 180 TY40 TY40 TY40 TY40 TY50 TY50 TY60 TY60 TY70 TY70 TY70 TY80 TY80 TY80 TY90 TY90 TY100 TY100 TY110 TY110 TY120 TY120 TY140 TY140 80 100 100 140 100 140 100 140 100 140 180 100 140 180 140 180 140 180 140 180 140 180 140 180 80 100 113 150 116 156 124 164 114 154 194 117 157 197 158 198 158 198 156 196 160 200 163 203
Bush Bore Bush Bore L M N P R S T V W X Y Size Max Min Size Max Min mm mm mm mm mm mm mm mm mm mm mm 1210 1210 1615 1615 1615 1615 1615 1615 2517 2517 2517 2517 2517 2517 2517 2517 3030 3030 3030 3030 3535 3535 3535 3535 32 32 42 42 42 42 42 42 60 60 60 60 60 60 60 60 75 75 75 75 100 100 100 100 11 11 14 14 14 14 14 14 16 16 16 16 16 16 16 16 25 25 25 25 35 35 35 35 1008 1008 1008 1008 1210 1210 1610 1610 2012 2012 2012 2517 2517 2517 2517 2517 3020 3020 3020 3020 3525 3525 3525 3525 25 25 25 25 32 32 42 42 50 50 50 60 60 60 60 60 75 75 75 75 100 100 100 100 9 9 9 9 11 11 14 14 14 14 14 16 16 16 16 16 25 25 25 25 35 35 35 35 127 62 21 63 103 82 25 15 14 147 82 21 63 103 82 25 15 14 160 82 34 76 126 95 32 15 18 200 122 34 76 126 135 32 15 18 163 79 34 76 126 95 32 15 18 203 119 34 76 126 135 32 15 18 163 71 34 76 126 95 32 15 18 203 111 34 76 126 135 32 15 18 177 81 41 108 178 95 48 16 22 217 121 41 108 178 135 48 16 22 257 161 41 108 178 175 48 16 22 193 79 41 108 178 95 48 16 22 230 119 41 108 178 135 48 16 22 270 159 41 108 178 175 48 16 22 230 117 41 108 178 135 48 16 22 270 157 41 108 178 175 48 16 22 267 117 72 140 210 135 60 20 29 307 157 72 140 210 175 60 20 29 267 117 72 140 210 135 60 20 29 307 157 72 140 210 175 60 20 29 294 117 85 160 250 135 80 20 34 334 157 85 160 250 175 80 20 34 294 117 85 160 250 135 80 20 34 334 157 85 160 250 175 80 20 34 15 15 16 16 16 16 16 16 17 17 17 17 17 17 17 17 20 20 20 20 20 20 20 20 2 22 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
31
Tyreflex
Ordering Code - Tyreflex
(continued)
TY 100 # # Tyreflex Size Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush
Component Spares
Coupling Size TY40 # # TY50 # # TY60 # # TY70 # # TY80 # # TY90 # # TY100 # # TY110 # # TY120 # # TY140 # # TY160 # # TY180 # # Tyre Flexible Element TY40 TY50 TY60 TY70 TY80 TY90 TY100 TY110 TY120 TY140 TY160 TY180 Half Body Unbored Type B TY40 B TY50 B TY60 B TY70 B TY80 B TY90 B TY100 B TY110 B TY120 B TY140 B TY160 B TY180 B Half Body Taper Bored Type F TY40 F TY50 F TY60 F TY70 F TY80 F TY90 F TY100 F TY110 F TY120 F TY140 F TY160 F TY180 F Half Body Taper Bored Type H TY40 H TY50 H TY60 H TY70 H TY80 H TY90 H TY100 H TY110 H TY120 H TY140 H TY160 H TY180 H
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
32
Discflex
A general purpose fail safe, torsionally flexible coupling, offering the option of either urethane or reinforced rubber disc, as the flexible element. Coupling Capacity: G G Maximum power @ 100RPM Maximum torque 45kW 4298Nm Standard Range Comprise: G Shaft to Shaft
Applications: G G G G G G Bottling Machines Compressors Mixers Pumps Screens General Industrial Applications
Features & Benefits: G G G G G G G Compact design, dimensionally small yet high power capacity. Torsionally flexible - shock absorbing, extending machine life. Maintenance free - minimum number of wearing parts. Misalignment capabilities allowing flexibility installation. Alternative flexible elements available for wide design choice. Optional fire retardent anti-static elements for use in flameproof environment. Taper bush bores available for ease of maintenance.
Construction Details: Cast Iron Half Bodies Urethane Disc - Temp Range -40 + 80C Rubber Reinforced Disc - Temp Range -40 + 90C
Discflex
E E
Type B
Coupling Number D41# # N # D52# # N # D52# # S # D52# # W # D71# # N # D71# # S # D71# # W # D89# # N # D89# # S # D89# # W # D108# # NR D108# # SR D108# # WR D127# # NR D127# # SR D127# # WR Power
Type F
Type F B mm 58 C mm 25 Dimensions D mm 104 E mm 11 F mm 16 22 Mass kg 2.1 4.9 5.0 5.1 11.0 11.1 11.2 20.8 21.0 21.7 40.0 40.0 41.0 65.0 66.0 67.0 End Float mm 1.8 2.5 2.5 2.5 3 3 3 3.8 3.8 3.8 4.6 4.6 4.6 5.3 5.3 5.3
Torque Speed
Type B
/100rpm Nominal Max* Bore Bush Bore Kw Nm rpm Max Min Size Max Min 0.75 1.5 2.25 3 3.75 5.25 7.5 9 12 15 19 23 26 30 38 45 72 143 215 287 358 501 716 860 1146 1433 1791 2149 2507 2865 3581 4298 900 110 55 TB3535 90 35 1050 95 38 TB3030 75 35 1300 75 32 TB2525 60 19 1650 60 28 TB2017 50 18 2250 42 19 TB1215 32 11 2900 32 12 TB1008 25 9
72
41
133
13
26 31 23
102
48
181
16
27 32 28
121
70
225
18
40 47 47
155
83
274
22
51 63 53
185
95
324
25
61 73
* Normal maximum speeds with 1 max. angular malalignment, above these speeds consult our Sales Technical Staff. Max angular misalignment 1 Max axial misalignment 0.5mm
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
34
Discflex
Ordering Code
Discflex Size Half Body Type B - Plain Bore F - Taper Bush D 52 # # # # Disc Material P - Polyurethane R - Rubber/Fabric Disc Size* N - Narrow S - Standard W - Wide Half Body Type B - Plain Bore F - Taper Bush * Disc size depending on torque transmitted.
Component Spares
Coupling Number D41 ## NP D41 ## NR D52 ## NP D52 ## NR D52 ## SP D52 ## SR D52 ## WP D52 ## WR D71 ## NP D71 ## NR D71 ## SP D71 ## SR D71 ## WP D71 ## WR D89 ## NP D89 ## NR D89 ## SP D89 ## SR D89 ## WP D89 ## WR D108 ## NR D108 ## SR D108 ## WR D127 ## NR D127 ## SR D127 ## WR Product No. BB Type 644763 647263 644766 647266 644767 647267 644768 647268 644769 647269 644770 647270 644771 647271 644772 647272 644773 647273 644774 647274 647275 647276 647277 647278 647279 647280 Product No. FF Type 644763/77 647263/77 644766/77 647266/77 644767/77 647267/77 644768/77 647268/77 644769/77 647269/77 644770/77 647270/77 644771/77 647271/77 644772/77 647272/77 644773/77 647273/77 644774/77 647274/77 647275/77 647276/77 647277/77 647278/77 647279/77 647280/77 Polyurethane Disc 644733 644736 644737 644738 644739 644740 644741 644742 644743 644744 Rubber/Fabric Disc 647233 647236 647237 647238 647239 647240 647241 647242 647243 647244 647245 647246 647247 647248 647249 647250 Pin Assembly 644204 644204 644207 644207 644207 644207 644207 644207 644210 644210 644210 644210 644210 644210 644213 644213 644213 644213 644213 644213 644216 644216 644216 644219 644219 644219 Half Body Pilot Bored 644205 644205 644208 644208 644208 644208 644208 644208 644211 644211 644211 644211 644211 644211 644214 644214 644214 644214 644214 644214 644217 644217 644217 644220 644220 644220 Half Body Taper Bored 644205/77 644205/77 644208/77 644208/77 644208/77 644208/77 644208/77 644208/77 644211/77 644211/77 644211/77 644211/77 644211/77 644211/77 644214/77 644214/77 644214/77 644214/77 644214/77 644214/77 644217/77 644217/77 644217/77 644220/77 644220/77 644220/77
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
35
Chainflex
An all metal flexible yet torsionally stiff coupling, suitable for use in arduous working conditions. Coupling Capacity: G G Maximum power @ 100RPM Maximum torque 90kW 8595Nm Standard Range Comprise: G Taper Bush or Parallel Bored
Features & Benefits: G G G G G G Torsionally stiff for use as a positive drive connection. Easy installation for ease of maintenance Misalignment capabilities allowing flexibility in installation. Hardened teeth giving long life with high torque capacity. All metal coupling for use in hostile environments. Taper bush bores available for ease of maintenance.
Construction Details: Hardened Steel Sprockets Renold Duplex Chain Moulded Cover
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
36
TYPE B
TYPE F
TYPE H C C
Coupling
Power
Torque Speed
Type B
Dimensions D mm 72 83 108 159 206 258 311 357 E mm 62 74 99 148 197 245 295 343 F Mass mm kg 3 5.1 6.9 8.9 16.2 18.8 25.1 31.2 0.5 1.0 2.1 7.1 16 30 61 85
Offset Max mm 0.25 0.25 0.25 0.30 0.38 0.38 0.50 0.50
End Float mm 0.7 1.0 1.3 2.0 2.5 3.3 3.8 4.6
Size /100rpm Nominal Max With Cover Kw Nm rpm C28BB K C33BB K C43 # # K C63 # # K C81 # # K C101BB K C122BB K C140BB K 0.55 1 2.25 7.5 17.5 33.5 60 90 52.5 95.5 215 716 1671 3200 5730 8595 3500 3000 2250 1500 1200 960 750 700
Bore Bush Bore Max Min Size Max Min 25 30 40 60 80 100 130 140 12 12 N/A N/A 9 14 19 -
Ordering Code
Chainflex Size Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush
C 63 # # # Supplied With or Without Cover K - With Cover Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush Max angular misalignment 1
Component Spares
With Cover Coupling Product Number Number C28BBK 642602 C33BBK C43BBK C43FFK C63BBK C63FFK C81BBK C81FFK C101BBK C122BBK C140BBK 642603 642604 642604/77 642606 642606/77 642608 642608/77 642610 642612 642614 Without Cover Coupling Product Number Number C28BB 642802 C33BB C43BB C43FF C63BB C63FF C81BB C81FF C101BB C122BB C140BB 642803 642804 642804/77 642806 642806/77 642808 642808/77 642810 642812 642814 Cover 616602 616603 616604 616604 616606 616606 616608 616608 616610 616612 616614 Half Body Pilot Bored 642080 642081 642082 642084 642086 642088 642090 642092 Half Body Half Body Taper Bored Taper Bored F Type H Type 642082/77 642084/77 642086/77 642082/88 642084/88 642086/88 Chain With Connectors 114500/96620 114038/96620 114046/96620 114046/96620 114066/96620 114066/96620 114088/96620 114088/96620 114106/96620 114127/96620 114147/96620
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
37
Rigid
C1 E C2 E C2 E
D B
D B
D B
Type BB
Coupling Size RC10 # # RC15 # # RC20 # # RC25 # # RC30 # # RC35 # # RC40 # # RC45 # # RC50BB RC55BB RC60BB RC70BB B Type Bore Dia. A Max Min 54 70 90 105 125 145 170 190 210 230 250 290 14 20 27 27 39 39 55 55 55 55 55 55 F & H Type* Bush Size TB1615 TB2012 TB2517 TB3030 TB3535 TB4040 TB4545 TB5050 N/A N/A N/A N/A Bore Max Min 42 50 60 75 90 100 110 125 14 14 16 35 35 40 55 70 B mm 76 98 124 148 173 201 233 262 294 324 349 406
Type FF
Dimensions C1 mm 42 49 62 77 91 106 121 135 153 168 188 229 C2 mm 42 35 47 79 91 106 121 135 D mm 116 152 178 213 240 279 318 346 389 425 457 527 E mm 14 19 19 22 22 29 29 29 38 38 25 29 F mm 5 5 5 5 5 5 10 10 10 10 13 16 B Type Weight kg 5.4 9.1 19.4 32.6 41.3 66.2 97.1 132 194 253 319 501
Type HF
F & H Type Weight kg 2.0 5.3 8.3 16.6 22.7 37.1 47.8 77.05 -
Ordering Code
Rigid Size
RC 30 # # Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush Half Body Type B - Plain Bore F - Taper Bush H - Taper Bush
Larger sizes are available. * NOTE: Torque transmitted by F & H types is limited by the torque capacity of the taper bush. NOTE: When connecting vertical shafts use type BB with keep plates or type FF. Type HF must not be used.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
38
Heavy duty all metal couplings, giving maximum power capacity within minimum space envelope and excellent misalignment capacity. Coupling Capacity: G G Maximum power @ 100RPM Maximum torque 50485kW 4747000Nm Range Options: G G G G G G G G G G Brake Disc/Drum Dis-engaging High Misalignment Up To 6 Long Hub M B Series Mill Motor Shear Pin Spindles Telescopic Torque Tube
Features & Benefits: G Heavy duty gear coupling for strength in application, combined with long life strength and long life. AGMA standard - interchangeable and cost effective. Single and double engagement types available, suiting all applicational requirements. Crowned and barrelled teeth for optimum contact and long life. Mill motor, shear pin and telescopic designs to give design suitability for demanding applications.
G G
G G
Construction Details: G G Steel half bodies and inner hubs. O Ring sealing
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
39
Gearflex - Introduction
Designed to meet the demands of todays wide ranging applications and manufactured to Renolds high standards.
Piloted Crown
Renold Gearflex Couplings feature an increased tooth capacity from optimised design, providing maximised power capacity within a given space envelope. Contact us for more information on how we can deliver a cost effective solution to your application.
Barreled Flank
Clutches & Couplings have the design and manufacturing capability to engineer a shaft coupling to suit customers special design application requirements. Note: M B series are also readily available in all variants. For details contact Renold.
Misalignment Capabilities: Double Engagement G Parallel Offset G Angular G Axial (End Float) Single Engagement G Angular G Axial (End Float)
When used in conjunction with a cardan shaft, two single engagement couplings will accept offset misalignment. The amount will be dependant upon the cardan shaft length.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
40
Vertical Series
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
41
Gearflex DA
L1 L2
NORMAL
F2
REVERSED
F1 C A C B D
REVERSED
F3
REVERSED
Offset
B C D F1 F2 F3 L1 L2 L3 Mass WR Max mm mm mm mm mm mm mm mm mm kg kg m2 mm 60 76 102 117 143 165 191 216 241 267 292 343 43 49 62 77 91 116 152 178 213 240 3 3 3 5 5 6 6 8 8 8 8 9 5 8 14 12 23 27 32 37 50 53 60 71 6 13 25 19 42 48 57 65 92 98 111 133 89 102 127 159 187 219 248 278 314 359 384 451 90 92 4.2 0.006 1.2 1.5 2.0 2.3 3.0 3.5 4.0 4.5 5.3 6.0 6.5
106 111 7.7 0.020 138 149 15.0 0.044 166 173 25.4 0.105 206 224 36.7 0.188 240 260 60.8 0.436 273 298 90.7 0.822 306 335 122 1.305 356 398 178 2.550 404 449 235 3.780 436 487 279 4.860
106 279 121 318 135 346 153 389 175 425 188 457 221 527
Catalogue ratings shown are nominal values at 1.50 degrees. For values at misalignments less than 1.50 degrees:Multiply nominal catalogue values by factor in table left. e.g. GF6DA at 1.50 = 104668 Nm at 0.75% = 104668 x 1.30:GF6DA at 0.75% = 136068 Nm
Ordering Code
** Speed in excess of these shown may require additional balancing. *** Hubs may be reversed to increase DBSE (F2 + F3 above). If axial movement is allowed with both hubs reversed, a stop plate should be fitted to prevent hubs disengaging from outers.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
42
Gearflex HDB
L M M
Options
1. Loose Spigot Ring 2. Bolt on End Plates
2 1
C F
Coupling Size GF8HDB GF9HDB GF10HDB GF11HDB GF12HDB GF14HDB GF16HDB GF18HDB GF20HDB GF22HDB GF24HDB GF26HDB
Power /100rpm Kw 1938 2663 2982 3653 4846 7231 11183 16031 22733 31309 37277 49707
Torque Nominal Nm 185120 254280 284800 348900 462800 690600 1068000 1531000 2171000 2990000 3560000 4747000
Speed Max** rpm 2000 1900 1800 1600 1400 1200 1000 700 500 400 300 270
Bore A Max* mm 275 305 360 370 410 465 535 605 665 720 780 840 Min mm 115 140 140 150 150 285 335 360 385 410 460 540 Rating Factor 1.00 1.20 1.60
Dimensions
B C D E F L M Mass Offset Angular Float mm mm mm mm mm mm mm kg mm deg mm 360 400 470 483 533 610 699 787 864 940 203 533 508 228 584 559 254 660 628 280 711 680 305 768 737 356 902 857 406 991 946 457 1124 1073 483 1230 1180 483 1308 1257 10 12 12 12 14 18 20 25 25 25 25 416 468 520 572 624 730 832 939 991 991 991 232 448 261 609 293 871 318 1070 343 1391 400 1767 457 2560 520 3485 560 4463 560 5358 560 6239 3.6 4.2 4.8 5.3 5.7 6.9 8.4 9.2 9.6 9.6 9.6 10.6 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 15.8 19.1 19.1 19.1 19.1 19.1 19.1 22.1 22.1 22.1 22.1 22.1
Catalogue ratings shown are nominal values at 0.75 degrees. For values at misalignments less than 0.75 degrees:Multiply nominal catalogue values by factor in table left.
Ordering Code
Gearflex Size Heavy Duty Series
GF 16 H DB Double Engagement
Long hub versions available contact Renold for details. See key stress calculations on page 14. * Maximum Bore - The maximum bores shown are absolute maximums. Under normal circumstances the boss to bore ratio should not be less than 1.5 for standard applications. Consult Renold for overbore approval. ** Speed in excess of these shown may require additional balancing.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
43
Gearflex SA
L
F C1 B1 A1 C2 A2 B2 D
Coupling Size GF10SA GF15SA GF20SA GF25SA GF30SA GF35SA GF40SA GF45SA GF50SA GF55SA GF60SA GF70SA
Power /100rpm Kw 14.9 28.2 48 77.6 128 196 312 431 578 857 1096 1640
Torque Nominal Nm 1423 2693 4584 7411 12224 18718 29796 41161 55199 81844 104668 156620
Speed Max** rpm 7100 5400 4800 4250 4000 3600 3290 2920 2630 2320 2120 1830
Bore A1 Max* mm 46 57 78 90 110 127 145 165 185 205 225 260 Min mm 14 20 27 27 39 39 55 55 55 55 55 55 Rating Factor 1.00 1.15 1.30 1.55 2.00
Bore A2 Max mm 58 75 95 110 130 155 180 200 225 250 265 310 Min mm 14 20 27 27 39 39 55 55 55 55 55 55
Dimensions B1 B2 C1 C2 D F L Mass WR2 mm mm mm mm mm mm mm kg kg m2 60 76 102 117 143 165 191 216 241 267 292 343 76 98 124 148 173 201 233 262 294 324 349 406 43 49 62 77 91 106 121 135 153 175 188 221 40 47 60 75 89 104 116 130 148 164 182 221 116 152 178 213 240 279 318 346 389 425 457 527 4 4 4 5 5 6 8 9 9 9 10 13 87 100 125 156 185 216 244 274 310 348 380 454 4.8 0.005 8.4 0.019 17.2 0.044 29.0 0.107 39.0 0.200 63.5 0.446 93.9 0.842 127 1.350 186 2.800 244 3.940 299 5.130 472 11.040
Catalogue ratings shown are nominal values at 1.50 degrees. For values at misalignments less than 1.50 degrees:Multiply nominal catalogue values by factor in table left.
Ordering Code
Gearflex Size
GF 40 SA Single Engagement
Long hub versions available. Contact Renold for details. See key stress calculations on Page 14. Renold can supply cardan shaft or torque tube assemblies. Critical speeds must be checked, please contact Renold. * Maximum Bore - The maximum bores shown are absolute maximums. Under normal circumstances the boss to bore ratio should not be less than 1.5 for standard applications. Consult Renold for overbore approval. ** Speed in excess of these shown may require additional balancing.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
44
Gearflex HSB
L M
Options
1. Loose Spigot Ring 2. Bolt on End Plates
2 1
E B1 A1
A2 B2 D
C1 F
C2
Coupling Size GF8HSB GF9HSB GF10HSB GF11HSB GF12HSB GF14HSB GF16HSB GF18HSB GF20HSB GF22HSB GF24HSB GF26HSB
Power
Torque
Speed
Bore A1
Bore A2
Dimensions
/100rpm Nominal Max** Max* Min Max Min B1 B2 C1 C2 D E F L M Mass Misalignment Float Kw Nm rpm mm mm mm mm mm mm mm mm mm mm mm mm mm kg deg mm 1938 2663 2982 3653 4846 7231 11183 16031 22733 31309 37277 49707 185120 254280 284800 348900 462800 690600 1068000 1531000 2171000 2990000 3560000 4747000 2000 1900 1800 1600 1400 1200 1000 700 500 400 300 270 275 305 360 370 410 465 535 605 665 720 780 840 115 140 140 150 150 285 335 360 385 410 460 540 240 280 305 330 356 430 480 560 610 635 660 710 Rating Factor 1.00 1.20 1.60 GF 20 H SB Gearflex Size Heavy Duty Series Single Engagement 115 360 368 203 200 533 508 13 416 232 411 140 400 406 228 226 584 559 14 468 261 557 140 470 457 254 252 660 628 14 520 293 877 150 483 533 280 278 711 680 14 572 318 1051 150 533 584 305 302 768 737 16 623 343 1365 190 610 660 356 354 902 857 21 731 400 1504 215 699 711 406 405 991 946 21 832 458 2184 255 787 864 457 456 1124 1073 27 940 521 2947 280 864 940 483 481 1230 1181 27 991 560 3717 300 940 965 483 481 1308 1257 27 991 560 4436 330 1016 1016 483 481 1372 1321 27 991 560 5227 355 1092 1168 559 560 1524 1486 28 1147 650 7993 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 7.9 9.6 9.6 9.6 9.6 9.6 9.6 11 11 11 11 11
Catalogue ratings shown are nominal values at 0.75 degrees. For values at misalignments less than 0.75 degrees:Multiply nominal catalogue values by factor in table left.
Ordering Code
Long hub versions available. Contact Renold for details. See key stress calculations on Page 14. Renold can supply cardan shaft or torque tube assemblies. Critical speeds must be checked, please contact Renold. * Maximum Bore - The maximum bores shown are absolute maximums. Under normal circumstances the boss to bore ratio should not be less than 1.5 for standard applications. Consult Renold for overbore approval. ** Speed in excess of these shown may require additional balancing.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
45
Gearflex GFV
B1 A1
C1
C2
A2 B2 D
Coupling Size GFV15DA GFV20DA GFV25DA GFV30DA GFV35DA GFV40DA GFV45DA GFV50DA GFV55DA GFV60DA GFV70DA
Power /100rpm Kw 14.9 28.2 48 77.6 128 196 312 431 578 857 1096
Torque Nominal Nm 1423 2693 4584 7411 12224 18718 29796 41161 55199 81844 104668
Speed Max** rpm 7100 5400 4800 4250 4000 3600 3290 2920 2630 2320 2120
Bore A1 Max* Min mm mm 46 57 78 90 110 127 145 165 185 205 225 14 20 27 27 39 39 55 55 55 55 55
Bore A2
Dimensions
2
Offset
Max Min B1 B2 C1 C2 D F L Mass WR Max mm mm mm mm mm mm mm mm mm kg kg m2 mm 75 95 110 130 155 180 200 225 250 265 310 20 27 27 39 39 55 55 55 55 55 55 60 76 98 124 49 62 77 91 47 60 75 89 152 178 213 240 279 318 346 389 425 457 527 8 8 9 10 12 13 17 17 17 20 23 104 161 190 222 250 9 0.019 0.8 1.0 1.2 1.4 1.7 2.0 2.3 2.6 3.0 3.4
102 148 117 173 143 201 165 233 191 262 216 294 241 324 267 349 292 406
106 104 121 116 135 130 153 148 175 164 188 182 221 221
282 128 1.350 318 187 2.800 356 245 3.940 390 300 5.130
Ordering Code
Gearflex Vertical Series Size
GF V 25 DA Double Engagement
* Maximum Bore - The maximum bores shown are absolute maximums. Under normal circumstances the boss to bore ratio should not be less than 1.5 for standard applications. Consult Renold for overbore approval. ** Speed in excess of these shown may require additional balancing.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
46
Gearflex NTS
H G B A
C E A E B D H G F L
C F L
C D
Coupling Size
Power /100rpm Kw
Torque Nominal Nm 668 955 1528 1910 3562 6112 9550 15570 22250 32660 40870 82800 104223 120000
Speed Max** rpm 10000 10000 10000 10000 10000 10000 8500 7250 6400 5700 5200 4500 4200 3900
Bore A Max* Min mm 24 30 40 40 55 70 80 100 115 125 145 165 180 190 mm 10 12 12 13 18 18 30 38 60 72 85 85 85 85 Rating Factor 1.00 1.15 1.30 1.55 2.00
Dimensions D E F G
mm mm mm mm mm mm mm mm 36 46 58 65 82 107 127 154 178 203 225 263 285 304 43 43 44 49 56 59 67 70 86 89 99 67 79 92 98 121 146 171 200 229 260 283 3 3 3 3 3 6 6 6 6 6 6 6 6 6 9 9 9 9 11 18 18 18 18 18 18 18 18 18 70 70 73 76 92 105 114 121 140 146 152 184 184 191 126 126 130 95 95 97
End Offset Float Max mm mm 0.18 0.18 0.18 0.20 0.20 0.23 0.33 0.36 0.38 0.41 0.43 0.46 0.48 0.48 1.5 1.5 1.5 1.5 1.5 1.5 3 3 3 3 3 3 3 3
GF10NTS # GF11NTS # GF12NTS # GF15NTS # GF20NTS # GF25NTS # GF30NTS # GF35NTS # GF40NTS # GF45NTS # GF50NTS # GF60NTS # GF65NTS # GF70NTS #
139 107 162 123 186 136 204 152 213 158 248 190 258 196 273 216 321 246 321 246 337 266
Catalogue ratings shown are nominal values at 1.50 degrees. For values at misalignments less than 1.50 degrees:Multiply nominal catalogue values by factor in table left.
Ordering Code
Gearflex Size
* Maximum Bore - The maximum bores shown are absolute maximums. Under normal circumstances the boss to bore ratio should not be less than 1.5 for standard applications. Consult Renold for overbore approval. ** Speed in excess of these shown may require additional balancing.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
47
Hydrastart
Soft
Start
Fluid
Couplings
A fluid coupling suitable for soft starting high inertia machinery with reduced current demand, controlled acceleration and torque with motor overload protection. Coupling Capacity: G G Maximum power @ 1500RPM 600kW Maximum speed 3500RPM G G G G G Dampens torsional vibration, reducing mechanical stress - extends machine life. Delay fill version - extends acceleration time and reduces start-up torque. Can match load and speed on multi drives. Energy saving through reduced current demand at start-up. Coupling and V pulley types - design flexibility.
Features & Benefits: G G G G High inertia controlled torque to 700 kW. Soft start - motor starts on low load. Allows use of standard squirrel cage motors. Overload protection - fusible plug safeguards equipment.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
49
Operating Principles
OUTER COVERS DRIVING IMPELLER (A) (OR PUMP)
INPUT
OUTPUT
The Renold HydraStart constant fill coupling (Type HS) comprises three major components:
The input and output positions shown are standard, but the input can be from either side of the coupling. The standard drive arrangement allows the outer cover to be rotated whilst at rest to facilitate oil filling. However, if a brake drum or disc brake is fitted, the brake should be at the coupling output. See page 59.
The coupling is partially filled with hydraulic oil to a level suitable for the absorbed power of the application and the acceleration characteristics of the driven machinery. The optimum oil fill is that which just allows the driven machine to accelerate from rest, thus providing the best drive overload protection. Power is supplied to the input side of the coupling by either an electric motor or diesel engine. This causes the driving impeller (A) to be rotated at motor speed, oil is thrown outwards by centrifugal force. The flow of oil is directed across the blades of the impeller towards the opposing turbine (B). Kinetic energy is absorbed by the turbine and translated into torque, which is always equal to the input torque and produces rotation of the output member (in the same direction as the driver). The low resistance of the impeller at start up allows the motor to quickly accelerate to full speed. The driven load accelerates smoothly to within a small percentage of the motor speed. This speed difference is referred to as slip and must always be present for the successful operation of a fluid coupling. Typical values of slip will vary between 2% (large power) and 6% (small power). All hydraulic Couplings can be driven in either directions of rotation.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
50
Delayed Fill
Hydrastart Delayed Fill Chamber (Type HSR)
HydraStart (constant fill) hydraulic couplings having a maximum oil fill will limit the starting torque to approximately 200% of nominal torque. It is possible to reduce this figure by reducing the quantity of oil in the circuit. The disadvantage of this method is that it produces increased slip and higher operating temperatures. To overcome these problems a delay fill chamber is available on sizes HS8 and above. This chamber is a modular option and allows a calibrated oil feed into the working circuit. In this way, starting torque can be reduced whilst minimising slip under normal running.
At rest
With the drive at rest, oil drains from the working circuit into the delay chamber.
Accelerating
At start up the coupling will transmit limited torque, allowing the motor to reach rated speed quickly. Oil flows from the chamber to the working circuit proportionally to the speed.
Running
When the coupling achieves its rated speed, almost all of the oil is in the working circuit and the torque is transmitted at the minimum slip value.
CAUTION
The outer case of the Hydrastart coupling can become hot during operation. Do not touch the coupling or a burn may result.
CAUTION
Do not attempt to change the coupling oil during or soon after operation has ceased, as the oil may be hot and could cause burns.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
51
Soft Starting
600
Fig. 3
500
Asorbed Current %
400
300
300
200
200
100
100
Input Speed %
= = = =
Locked rotor torque Stall torque 250/280% Normal torque 100% Amperage
600
100
20
40
60
80
Torque %
Fig. 4A
500
Fig. 4B
Slip 100%
Asorbed Current %
Starting Torque %
400
200
300
200
100
100
Slip 2-6%
20
40
60
80
100
Time %
Output Speed %
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
52
100
20
40
60
80
Soft Starting
100
Fig. 5
80
100% Slip
Engine Torque %
60
60
40
20
Input Speed %
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
53
100
20
40
60
80
2950
3600
200
HS10 HS8
100 80 60 40
HS6
20
HS4
kW
10 8 6 4
HS2
0.2
500
600
700
800
900
1000
1200
1400
1600
1800 2000
2400
2800
3200 3500
t/mn
This chart may be used for the selection of coupling size. If your selection falls on a dividing line, always select the next largest size and use reduced oil fill. Hydrastart couplings can be used for up to five equi-spaced starts per hour. Applications requiring more than five starts an hour should always be referred to Renold. Rotating equipment must be provided with a suitable guard before operating or injury may result.
NOTE: Hydraulic couplings will not compensate for an under-sized electric motor.
It is the responsibility of the system designer to ensure that the application of the coupling does not endanger the other constituent components in the system. Service factors given are an initial selection guide.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
54
HS2
HS2
HS4
HS6
HS10
15 20 18.5 25 22 30
18.5 25
HS11
HS13
HS13
HS12
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
55
Page 58
Delay Fill
TYPE: HS..RPF
TYPE: HS..B
59
TYPE: HS..RB
TYPE: HS..K
59
TYPE: HS..RK
TYPE: HS..GF
60
TYPE: HS..RGF
TYPE: HS..VP
61
TYPE: HS..RVP
Type HSPF, HSB, HSK and HSVP may be used for vertical applications. Please contact Renold for details.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
56
Overload Protection
When a hydraulic coupling experiences overload there is a correspondingly high slip value accompanied by a rise in the oil temperature. To prevent damage to the drive there are three options available.
1. Fusible plug
This is fitted as standard on all HydraStart couplings sizes 4 and above. The standard plug is set to fuse at 138C. Another option available allows fusing at 183C. Because oil is discharged when the plug fuses it is advisable to correctly guard couplings using this type of device.
32 2 8
16 L L1
2. Thermal trigger
Fitted as an option on HydraStart couplings sizes 6 and above, this device prevents oil being discharged from the coupling at overload. As with the fusible plug, two melt temperatures are offered. When melt point is reached a pin is released which engages with a limit switch. The signal from this switch can operate an alarm or switch off the electric motor to protect the drive. After the cause of the overload has been removed the drive can be restarted after replacing the thermal trigger.
3. Non-contact sensor
Non-contact speed and heat sensors can be supplied which shut down the drive in the event of overload. Please contact Renold for more information.
Operating principles
This device will trigger the limit switch if the oil temperature reaches a predetermined level without loss of oil from the coupling. Fusible trigger plug 117C alternatively 138C.
Electrical characteristics
2-Pole 1N/C + 1N/O, conforms to IEC 529 IP 66, contact type XCK rating 500V AC-15 3-20mm ISO Cable Entries.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
57
Di
G J
Di
G J
D A
HydraStart Pinflex Coupling (HS..PF & HS..RPF) Delay fill option available on size 8 and larger Size A B Bi C D Max Di Max E F G* H J L Li Pinflex Weight Cplg. Size HS2 229 90 44 29 50 13 4 80 0.625 11 UNC 0.625 11 UNC 0.75 10 UNC 1.00 8 UNC 1.00 8 UNC 1.00 8 UNC 1.25 7 UNC 1.25 7 UNC 8 146 1 6.7 0.02 kgs WR2 kgm2
HS4
286
107
44
42
50
13
95
162
10.9
0.06
HS6
345
130
50
52
55
16
114
10
195
20.8 41.2 43.9 65.2 69.7 107.4 113.6 131.7 138.9 199 207
0.16 0.46 0.49 1.05 1.11 2.17 2.26 3.67 3.78 6.80 7.07
HS8
422
161
238
75
75
80
20
137
19
261
338
HS10
511
191
268
89
85
110
20
178
25
311
388
HS11
580
205
296
110
102
130
20
195
25
347
438
HS12
669
231
339
110
115
130
23
211
25
374
482
HS13
751
292
402
130
127
150
23
267
25
454
564
Figures in bold type relate to delay fill coupling only (sizes 8 and above). * It may be necessary to use a spacer (not supplied by Renold) if shaft length is less than dimension G.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
58
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
INPUT
OUTPUT
INPUT
OUTPUT
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
59
D A
HydraStart Gearflex Coupling (HS..GF & HS..RGF) Delay fill option available on size 8 and larger Gearflex Couplings are AGMA standard exposed bolt type Size A B Bi C D Max E Ei F G K Gearflex Cplg. Size HS2 HS4 HS6 229 286 345 128 145 168 45 45 51 44 44 58 132 148 171 2 2 2 43 43 49 19 19 19 1 1 1.5 7.80 12.10 19.60 44.20 HS8 422 223 300 64 76 226 306 2 62 29 2 47.00 69.00 HS10 511 252 329 94 110 257 335 3 91 29 3 73.50 100.70 HS11 580 267 358 94 110 272 363 3 91 29 3 106.80 130.30 HS12 HS13 669 297 405 110 120 303 408 3 106 31 3.5 137.50 0.03 0.06 0.15 0.49 0.51 1.12 1.18 2.13 2.22 3.69 3.81 Weight kgs WR2 kgm2
Details on request
Figures in bold type relate to delay fill option only (sizes 8 and over). WR2 value does not include gear coupling halves.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
60
H G D A
H G D
Hydrastart Pulley (HS..VP & HS..RVP) Delay Fill Option Available on Size 8 And Larger. Size A B Bi C D Max E G* H M Weight kgs. WR2# kg.m2 Hydrastart Size HS2VP HS2 229 141 90 27 13 123 0.625 11 UNC 0.625 11 UNC 51 4.40 0.02 HS4VP HS4 286 173 107 38 13 154 66 9.30 0.05 HS6VP HS6 345 220 130 49 16 195 0.75 10 UNC 90 15.89 0.13 HS8VP HS8 422 310 387 161 75 20 267 1.00 8 UNC 149 41.40 44.10 0.45 0.48 HS10VP HS10 511 357 434 191 80 20 319 1.00 8 UNC 166 66.70 71.20 1.06 1.12 HS11VP HS11 580 418 509 205 95 20 382 1.00 8 UNC 213 104.10 110.30 2.12 2.21 HS12VP HS12 669 448 556 231 110 23 403 1.25 7 UNC 217 137.20 144.40 3.71 3.83 Groove Profile SPZ SPA SPB SPZ SPA SPB SPZ SPA SPB SPC SPZ SPA SPB SPC SPZ SPA SPB SPC SPZ SPA SPB SPC SPZ SPA SPB SPC Max No Grooves 3 2 1 5 4 3 6 5 4 3 11 9 7 5 13 10 8 6 17 13 10 8 17 13 10 8 PCD Min 106 110 116 140 144 150 162 166 172 182 188 192 198 208 245 250 255 265 285 289 295 305 330 334 340 350
Figures in bold type refer to delay fill coupling option only (sizes 8 and over). *It may be necessary to use a spacer (not supplied by Renold) if the shaft length is less than dimension G. *WR2 value does not include the pulley. Pulley details shown are limitations. For alternative options contact Renold.
RENOLD Clutches and Couplings. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com
61
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 62
RB Flexible Coupling
General purpose, cost effective range which is manufactured in SG iron for torques up to 41kNm. Features & Benefits
G
Applications
G G G G
G G
Intrinsically fail safe ensuring continuous operation of the driveline in the unlikely event of rubber damage. Control of resonant torsional vibration achieving low vibratory loads in the driveline components by selection of optimum stiffness characteristics. Maintenance free with no lubrication or adjustment required resulting in low running costs. Severe shock load protection avoiding failure of the driveline under short circuit and other transient conditions. Misalignment capability allows axial and radial misalignment between the driving and driven machines. Zero backlash eliminating torque amplifications through pre -compression of the rubber elements.
Generator sets Pump sets Compressors Wind turbines Metal manufacture Bulk handling Pulp and paper industry General purpose industrial applications
G G
Shaft to shaft with increased shaft engagement Flywheel to shaft Flywheel to shaft with increased shaft engagement
Separate rubber elements with a choice of grade and hardness with SM70 shore hardness being the standard. Rubber elements which are totally enclosed and loaded in compression.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 63
RB Shaft to Shaft
Rigid half / Flex half
W3 J3 B J J SxT W2 J2
Features
G Can accommodate a
Benefits
G Allows the optimum
coupling to be selected
G Allows the driving
QxR W1 J1 Y G
D A F E X
D1
Coupling Size 0.12 0.2 0.24 0.37 0.73 1.15 2.15 3.86 5.5 Coupling Size 0.12 0.2 0.24 0.37 0.73 1.15 2.15 3.86 55.5 A mm B C D D1 E mm mm mm mm mm 3.2 3.2 3.2 3.2 3.2 3.2 50.8 54.0 60.3 66.7 85.7 95.2 50.8 54.0 F mm G mm 178 210 251 295 362 435 J mm 14.3 17.5 19.0 19.0 19.0 22.2 Q mm 5 6 6 6 6 6 6 7 8 R mm M8 M8 M8 M10 M10 M12 M12 M12 M12 S mm 6 6 6 8 8 10 16 12 12 T mm M8 M8 M10 M10 M12 M12 M12 M16 M16 U mm 9.2 9.2 11.2 11.2 13.2 13.2 13.2 17.25 17.25 MAX.X mm 50 60 65 80 95 115 140 170 210 MAX.Y MIN.X&Y mm mm 55 70 75 85 95 115 140 170 210 30 35 40 40 55 55 70 80 90
200.0 104.8 222.2 111.2 238.1 123.8 260.3 136.5 308.0 174.6 358.8 193.7 466.7 233.4 508.0 260.4 577.8 285.8
60.3 101.6 212.7 186.5 15.9 66.7 120.6 235.0 85.7 152.4 279.4 95.2 184.1 323.8
4.8 114.3 114.3 222.2 438.15 6.4 127.0 127.0 279.4 469.9
6.4 139.7 139.7 330.2 536.6 501.5 25.4 Max. Speed (rpm) (1) 5250 4725 4410 4035 3410 2925 2250 2070 1820
Weight (3)Kg W1 2.82 4.04 5.29 7.49 W2 4.0 5.05 6.38 8.14 W3 4.06 5.82 7.42
Inertia (3)Kgm2 J1 J2 J3
Allowable Misalignment (2) Radial (mm) Axial (mm) Conical (degree) 0.75 0.75 0.75 0.75 1.0 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 2.0 3.0 3.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
12.82 13.29 18.03 0.0563 0.20 0.1475 23.39 18.41 27.37 0.1399 0.3674 0.2862 35.88 33.98 47.43 0.3227 1.1035 0.7998 62.81 43.87 75.39 0.8489 1.9161 1.512 102.09 59.0 113.32 1.9633 3.4391 2.9796
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. (2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery should be calculated to ensure that these do not exceed the manufacturers allowables. (3) Weights and inertias are based on the minimum bore size.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 64
Features
G
Benefits
G
J J
Allows small diameter long length shafts to be used Reduces key stress Allows increased distances between shaft ends Full shaft engagement avoids the need for spacer collars
AF E X
D2
W1 J1 Y G
G
Coupling Size 0.12 0.2 0.24 0.37 0.73 1.15 2.15 3.86 5.5 Coupling Size 0.12 0.2 0.24 0.37 0.73 1.15 2.15 3.86 5.5 A B1 B2 C mm mm mm mm 200.0 139.0 54.0 222.2 152.2 57.2 238.1 173.5 63.5 260.3 189.9 69.8 308.0 233.9 88.9 358.8 268.4 98.4 3.2 3.2 3.2 3.2 3.2 3.2 D mm 50.8 54.0 60.3 66.7 85.7 95.2 D2 mm 85 95 E mm 79.4 95.2 F mm 200.0 G mm 178 210 251 295 435 J mm 14.3 17.5 19.0 19.0 19.0 22.2 Q mm 5 6 6 6 6 6 6 7 8 R mm M8 M8 M8 M10 M10 M12 M12 M12 M12 S mm 6 6 6 8 8 10 16 12 12 T mm M8 M8 M10 M10 M12 M12 M12 M16 M16 U mm 9.2 9.2 11.2 11.2 13.2 13.2 13.2 17.25 17.25 MAX.X MAX.Y MIN.X&Y mm mm mm 50 6. 65 80 95 115 140 170 210 55 70 75 85 95 115 140 170 210 30 35 40 40 55 55 70 80 90
110 101.6 212.7 186.5 15.9 120 120.6 235.0 145 152.4 279.4 170 184.1 323.8
466.7 309.1 119.0 4.8 508.0 343.4 133.4 6.4 577.8 386.1 146.0 6.4 Rubber Elements Per Cavity 1 1 1 1 1 1 1 1 1
139.7 240 330.2 536.6 501.5 25.4 Max. Speed (rpm) (1) 5250 4725 4410 4035 3410 2925 2250 2070 1820 Weight (3)Kg W1 4.21 6.42 8.67 11.85 W2 4.0 5.05 6.38 8.14 W3 4.06 5.82 7.42
Inertia (3)Kgm2 J1 J2 J3
Allowable Misalignment (2) Radial (mm) Axial (mm) Conical (degree) 0.75 0.75 0.75 0.75 1.0 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 2.0 3.0 3.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Per Coupling 10 12 12 12 12 12 12 14 16
19.43 13.29 18.03 0.0770 0.20 0.1475 35.28 18.41 27.37 0.1896 0.3674 0.2862 53.81 33.98 47.43 0.4347 1.1035 0.7998 95.50 43.87 75.39 1.1833 1.9161 1.512 162.79 59.0 113.32 2.8953 3.4391 2.9796
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. (2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery should be calculated to ensure that these do not exceed the manufacturers allowables. (3) Weights and inertias are based on the minimum bore size.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 65
Features
SxU
G
Benefits
G
Wide range of adaptor plates Choice of rubber compound and hardness Short axial length
Allows the coupling to be adapted to suit most engine flywheels Allows control of the torsional vibration system Allows the coupling to fit in bell housed applications
QxR
W1 C A F D1 Y G J1
Coupling Size 0.24 0.37 0.73 1.15 SAE No. 10 11.5 11.5 14 11.5 14 14 18 Coupling Size 0.24 0.37 0.73 1.15 SAE No. 10 11.5 11.5 14 11.5 14 14 18 A mm 314.3 352.4 352.4 466.7 352.4 466.7 466.7 571.5 C mm 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 D1 mm 60.3 60.3 66.7 66.7 85.7 85.7 95.2 95.2 F mm 295.27 333.38 333.38 438.15 333.38 438.15 438.15 542.92 G mm 186.5 186.5 210 210 251 251 295 295 J mm 20 20 20 20 20 20 20 28 L mm 79.5 79.5 85.8 85.8 104.9 104.9 114.4 122.4 Q mm 6 6 6 6 6 6 6 6 R mm M8 M8 M10 M10 M10 M10 M12 M12 S mm 8 8 8 8 8 8 8 6 U mm 10.5 10.5 10.5 13.5 10.5 13.5 13.5 16.7 MAX.Y mm 75 75 85 85 95 95 115 115 MIN.Y mm 40 40 40 40 55 55 55 55
Max. Speed (rpm) (1) 3710 3305 3305 2500 3310 2500 2500 2040
Weight (3)Kg W1 5.29 5.29 7.49 7.49 12.82 12.82 23.39 23.39 W2 15.71 17.1 19.96 28.76 24.01 35.31 39.03 61.0
Inertia (3)Kgm2 J1 0.0131 0.0131 0.0233 0.0233 0.0563 0.0563 0.1399 0.1399 J2 0.1922 0.2546 0.3087 0.7487 0.40 0.89 1.0274 2.3974
Allowable Misalignment (2) Radial (mm) Axial (mm) Conical (degree) 0.75 0.75 0.75 0.75 1.0 1.0 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. (2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery should be calculated to ensure that these do not exceed the manufacturers allowables. (3) Weights and inertias are based on the minimum bore size.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 66
QxR W1 D1 Y G J1 A F C D1 Y G
QxR
C A F
W1 J1
Coupling Size 2.15 SAE No. 14 18 21 3.86 18 21 24 5.5 18 21 24 Coupling Size 2.15 SAE No. 14 18 21 3.86 18 21 24 5.5 18 21 24 A mm 466.7 571.5 673.1 571.5 673.1 733.4 571.5 673.1 733.4 C mm 4.8 4.8 4.8 6.4 6.4 6.4 6.4 6.4 6.4 D1 mm 114.3 114.3 114.3 127.0 127.0 127.0 139.7 139.7 139.7 F mm 438.15 542.92 641.35 542.92 641.35 692.15 542.92 641.35 692.15 G mm 362.0 362.0 362.0 435.0 435.0 435.0 501.5 501.5 501.5 J mm 35.0 28.0 28.0 28.0 31.0 31.0 41.4 28.0 31.0 L mm 135.05 143.0 143.0 157.35 160.35 160.35 162.05 170.0 173.05 Q mm 6 6 6 7 7 7 8 8 8 R mm M12 M12 M12 M12 M12 M12 M12 M12 M12 S mm 8 6 12 6 12 12 6 12 12 U mm 13.2 16.7 16.7 16.7 16.7 22 16.7 16.7 22 MAX.Y mm 140 140 140 170 170 170 210 210 210 MIN.Y mm 70 70 70 80 80 80 90 90 90
Max. Speed (rpm) (1) 2500 2040 1800 2040 1800 1590 2040 1800 1590
Weight (3)Kg W1 35.88 35.88 35.88 62.81 62.81 62.81 102.09 102.09 102.09 W2 50.42 79.17 92.19 86.46 110.35 120.33 79.14 117.21 135.46
Inertia (3)Kgm2 J1 0.3227 0.3227 0.3227 0.8489 0.8489 0.8489 1.9633 1.9633 1.9633 J2 1.6535 3.2935 4.9935 3.9461 6.4661 8.1461 4.5684 7.3291 9.6691
Allowable Misalignment (2) Radial (mm) Axial (mm) Conical (degree) 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 2.0 2.0 2.0 3.0 3.0 3.0 3.0 3.0 3.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. (2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery should be calculated to ensure that these do not exceed the manufacturers allowables. (3) Weights and inertias are based on the minimum bore size.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 67
Features
G
Benefits
G
SxU
Allows small diameter long length shafts to be used Reduces key stress Allows increased distance between shaft end and flywheel Full shaft engagement avoids the need for spacer collars
QxR W1 J1 Y G
G
C A F
D2
Coupling Size 0.24 0.37 0.73 1.15 SAE No. 10 11.5 11.5 14 11.5 14 14 18 A mm 314.3 352.4 352.4 466.7 352.4 466.7 466.7 571.5 C mm 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 D2 mm 110 110 120 120 145 145 170 170 F mm G mm J mm 20 20 20 20 20 20 20 28 L mm 79.5 79.5 85.8 85.8 104.9 104.9 114.4 122.4 L1 mm 129.2 129.2 139.1 139.1 164.2 164.2 189.2 197.2 Q mm 6 6 6 6 6 6 6 6 R mm M8 M8 M10 M10 M10 M10 M12 M12 S mm 8 8 8 8 8 8 8 6 U mm 10.5 10.5 10.5 13.5 10.5 13.5 13.5 16.7 MAX.Y mm 75 75 85 85 95 95 115 115 MIN.Y mm 40 40 40 40 55 55 55 55
295.27 186.5 333.38 186.5 333.38 438.15 333.38 438.15 438.15 542.92 210 210 251 251 295 295
Max. Speed (rpm) (1) 3710 3305 3305 2500 3305 2500 2500 2040
Weight (3)Kg W1 8.67 8.67 11.85 11.85 19.43 19.43 35.28 35.28 W2 15.71 17.10 19.96 28.76 24.01 35.31 39.03 61.0
Inertia (3)Kgm2 J1 0.0193 0.0193 0.0326 0.0326 0.0770 0.0770 0.1896 0.1896 J2 0.1922 0.2546 0.3087 0.7487 0.40 0.89 1.0274 2.3974
Allowable Misalignment (2) Radial (mm) Axial (mm) Conical (degree) 0.75 0.75 0.75 0.75 1.0 1.0 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. (2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery should be calculated to ensure that these do not exceed the manufacturers allowables. (3) Weights and inertias are based on the minimum bore size.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 68
QxR W1 J1 Y G A F W1 J1 Y G
C A F
D2
D2
Coupling Size 2.15 SAE No. 14 18 21 3.86 18 21 24 5.5 18 21 24 Coupling Size 2.15 SAE No. 14 18 21 3.86 18 21 24 5.5 18 21 24 A mm 466.7 571.5 673.1 571.5 673.1 733.4 571.5 673.1 733.4 C mm 4.8 4.8 4.8 6.4 6.4 6.4 6.4 6.4 6.4 D2 mm 190 190 190 210 210 210 240 240 240 F mm 438.15 542.92 641.35 542.92 641.35 692.15 542.92 641.35 692.15 G mm 362.0 362.0 362.0 435.0 435.0 435.0 501.5 501.5 501.5 J mm 35.0 28.0 28.0 28.0 31.0 31.0 41.4 28.0 31.0 L mm 135.0 143.0 143.0 157.4 160.4 160.4 162.05 170.0 173.0 L1 mm 210.7 219.7 219.7 240.4 243.4 243.4 262.4 271.3 273.3 Q mm 6 6 6 7 7 7 8 8 8 R mm M12 M12 M12 M12 M12 M12 M12 M12 M12 S mm 8 6 12 6 12 12 6 12 12 U mm 13.5 16.7 16.7 16.7 16.7 22 16.7 16.7 22 MAX.Y mm 140 140 140 170 170 170 210 210 210 MIN.Y 70 70 70 80 80 80 90 90 90
Max. Speed (rpm) (1) 2500 2040 1800 2040 1800 1590 2040 1800 1590
Weight (3)Kg W1 53.81 53.81 53.81 95.50 95.50 95.50 162.79 162.79 162.79 W2 50.42 79.17 92.19 86.46 110.35 120.33 79.14 117.21 135.46
Inertia (3)Kgm2 J1 0.4347 0.4347 0.4347 1.1833 1.1833 1.1833 2.8953 2.8953 2.8953 J2 1.6535 3.2935 4.9935 3.9461 6.4661 8.1461 4.5684 7.3291 9.6691
Allowable Misalignment (2) Radial (mm) Axial (mm) Conical (degree) 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 2.0 2.0 2.0 3.0 3.0 3.0 3.0 3.0 3.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. (2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery should be calculated to ensure that these do not exceed the manufacturers allowables. (3) Weights and inertias are based on the minimum bore size.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 69
RB Technical Data
1.1 Diesel Engine Drives
Given sufficient axial force as shown in the catalogue, the coupling will slip to its new position immediately. The RB Coupling is selected on the nominal torque TKN without service factors for Diesel Drive applications. The full torque capacity of the coupling for transient vibration whilst passing through major criticals on run up is published as the maximum torque. (TKmax = 3 x TKN ). There is an additional torque capacity built into the coupling for short circuit and shock torques, which is 3 x Tkmax. The published Vibratory torque Tkw, is a fatigue function according to DIN740 and not significant in diesel engine drives, the vibratory torque values shown in the Technical Data are at the frequency of 10Hz. The measure used for acceptability of the coupling under vibratory torque is heat dissipation of the rubber elements. The maximum allowable heat dissipation shown in the technical data is at a 30C ambient temperature.
2.4
An adequate prediction of the system torsional vibration characteristics can be made by the following method.
2.4.1
Use the torsional stiffness as published in the catalogue which is based upon data measured at a 30C ambient temperature (CT30).
1.2
Industrial Drives
For industrial Electrical Motor Applications refer to the Selection Procedures and base the selection on Tkmax with the appropriate service factors. The service factors used in the Selection Procedures are based upon 40 years experience of drives and their shock frequency/amplitude. The stated TKmax quoted should not be exceeded by design, without reference to Renold Hi-Tec Couplings. Care needs to be taken in the design of couplings with shaft brakes to ensure the coupling torques are not increased by severe deceleration.
2.4.2
Repeat the calculation made as 2.4.1 but using the maximum temperature correction factor St100 and M100 for the rubber selected for both torsional stiffness and dynamic magnifier from the table on page 73. CT100 = CT30 x St
2.4.3
Review the calculations 2.4.1 and 2.4.2 and if the speed range is clear of criticals which do not exceed the allowable heat dissipation value as published in the catalogue, the coupling is then considered suitable for the application with respect to the torsional vibration characteristics. If there is a critical in the speed range the actual temperature of the coupling will need to be calculated at this speed.
2.0
Stiffness Properties
The Renold Hi-Tec Coupling remains fully flexible under all torque conditions. The RB series is a non-bonded type operating with the Rubber-in-Compression principle.
2.1
Axial Stiffness
When subject to misalignment forces in the axial direction, the coupling will have an axial resistance which gradually reduces due to the effect of vibratory torques.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 70
RB Technical Data
Rubber Grade Tempmax St
2.6
Temperature Correction Factor St
1 0.9 0.8 0.7 0.6 0.5
SM 60 SM 70 SM 80
SM 70 is considered standard Rubber Grade Dynamic Magnifier at 30C (M30) 8 6 4 Dynamic Magnifier at 100C (M100) 10.7 9.5 6.9
30
40
50
60
70
80
90
100
SM 60 SM 70 SM 80
RUBBER TEMPERATURE C
2.7
SM 70 is considered standard
2.5
variation in the same way as the torsional stiffness. MT = M30 St Rubber Grade SM 60 SM 70 SM 80
T = 30 x St
Dynamic Magnifier (M30 ) 8 6 4 Relative Damping
30
SM 70 is considered standard
( )
2.4
Calculate the coupling temperature as per 2.5. Repeat calculation until the coupling temperature agrees with the correction factors for torsional stiffness and dynamic magnifier used in the calculation.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 71
RB Technical Data
Coupling Size 0.12 0.2 0.24 0.37 0.73 1.15 2.15 3.86 5.5 Nominal Torque TKN (kNm) 0.314 0.483 0.57 0.879 1.73 2.731 5.115 9.159 13.05 Maximum Torque Tkmax (kNm) 0.925 1.425 1.72 2.635 5.35 8.1 15.303 27.4 41.0 Vibratory Torque TKW (kNm) 0.122 0.188 0.222 0.342 0.672 1.062 1.989 3.561 5.075 Allowable Dissipated Heat at Amb. Temp. 30C Pkw (W) SM60 SM70 SM80 90 112 125 140 185 204 246 336 426 98 123 138 155 204 224 270 369 465 100 138 154 173 228 250 302 410 520
Coupling Size SM60 0.12 0.2 0.24 0.37 0.73 1.15 2.15 3.86 5.5 0.006 0.010 0.014 0.018 0.035 0.050 0.110 0.200 0.300 @ 0.25 TKN SM70 0.007 0.012 0.016 0.022 0.041 0.064 0.118 0.240 0.400 SM80 0.020 0.032 0.042 0.060 0.111 0.173 0.318 0.637 0.920 SM60 0.014 0.030 0.030 0.042 0.080 0.130 0.245 0.500 0.800
Dynamic Torsional Stiffness (MNm/rad) @ 0.50 TKN SM70 0.016 0.036 0.033 0.048 0.089 0.138 0.254 0.510 0.850 SM80 0.028 0.046 0.060 0.087 0.160 0.249 0.458 0.918 1.500 SM60 0.030 0.050 0.065 0.100 0.170 0.280 0.500 1.000 1.600 @ 0.75 TKN SM70 0.029 0.048 0.062 0.091 0.168 0.260 0.480 0.964 1.540 SM80 0.042 0.070 0.089 0.132 0.242 0.374 0.690 1.384 2.560 SM60 0.045 0.080 0.100 0.145 0.270 0.420 0.800 1.550 2.650 @ 1.0 TKN SM70 0.043 0.073 0.092 0.138 0.251 0.390 0.719 1.448 2.450 SM80 0.052 0.086 0.110 0.163 0.298 0.462 0.851 1.709 3.550
Coupling Size 0.12 0.2 0.24 0.37 0.73 1.15 2.15 3.86 5.5
Radial Stiffness No Load (N/mm) SM60 1020 1260 1435 1594 2116 2310 2870 3740 4728 SM70 1255 1550 1765 1962 2586 2845 3530 4600 5810 SM80 1728 2135 2430 2700 3654 3915 4860 6330 8008 SM60 2046 2536 2880 3207 4250 4650 5780 7520 9510
Radial Stiffness @TKN (N/mm) SM70 2134 2638 3000 3435 4396 4835 6000 7820 9890 SM80 2310 2855 3250 3610 4885 5235 6500 8465 10700
Axial Stiffness No Load (N/mm) SM60 1030 1250 1400 1600 2095 2310 2850 3700 4700 SM70 1100 1350 1510 1710 2200 2500 3100 4100 5200 SM80 2940 3690 4060 4620 6060 6700 8220 10760 13580
Max. Axial Force (1) (N) @TKN SM60 1080 1350 1500 1700 2200 2460 3000 3900 5000 SM70 1150 1440 1600 1800 2360 2600 3200 4100 5300 SM80 1300 1600 1760 2000 2600 2900 3500 4600 5800
NB. SM70 is supplied as standard rubber grade with options of rubber grades SM60 or SM80 if these are considered a better solution to a dynamic application problem. It should be noted that for operation above 80% of the declared maximum coupling speed the coupling should be dynamically balanced. (1) The Renold Hi-Tec Coupling will slip axially when the maximum axial force is reached.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 72
RB Design Variations
The RB coupling range can be adapted to meet customer needs. Below are some of the arrangements that have been produced. For more comprehensive list contact Renold Hi-Tec Couplings.
Coupling with large boss driving flange and long boss inner member for vertical applications.
Coupling with brake drum for use on cranes, fans and conveyor drives.
Cardan shaft coupling used to increase the misalignment capability and half the torsional stiffness.
Spacer coupling used to increase the distance between shaft ends and allow easy access to driven and driving machine.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 73
PM Flexible Coupling
Heavy duty steel coupling for torques up to 6000KNm Features & Benefits
G G
Severe shock load protection avoiding failure of the driveline under high transient torques. Intrinsically fail safe ensuring continuous operation of the driveline in the unlikely event of rubber failure or damage. Maintenance free with no lubrication or adjustment required resulting in low running costs. Vibration control achieving low vibratory loads in the driveline components by selection of optimum stiffness characteristics. Zero backlash eliminating torque amplifications through pre -compression of the rubber elements. Misalignment capability allows axial and radial misalignment between the driving and driven machines.
G
Shaft to shaft Flange to shaft Mill motor coupling Brake drum coupling
Applications
G G G G G G G G
Metal manufacture Mining and mineral processing Pumps Fans Compressors Cranes and hoists Pulp and paper industry General heavy duty industrial applications
Construction details
G
PM Couplings up to and including PM600 are manufactured in steel. Driving flanges up to and including PM60 are steel forgings to BS970 grade 070 M55. Driving flanges PM90 to PM600 and all inner and outer members up to PM600 are steel casting to BS 3100 grade A4. PM Couplings above PM900 are supplied in spheroidal graphite to BS2789 grade 420/12 unless otherwise specified.
Separate rubber elements with a choice of grade and hardness, styrene butadiene with 60 shore hardness (SM60) being the standard. Rubber elements loaded in compression.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 74
90 - 130
B W3 JJ W SxT W2 J2 QxR W1 J1 Y G
AF E X
Y G
AF EX
Coupling Size 0.4 0.7 1.3 3 6 8 12 18 27 40 60 90 130 Coupling Size 0.4 0.7 1.3 3 6 8 12 18 27 40 60 90 130 A mm 161.9 187.3 215.9 260.3 260 302 338 392 440 490 568 638 728 B C D D1 E mm mm mm mm mm 103 110 130 143 175 193 221.5 254 290.5 329 377.5 432.5 487 1 2 2 3 3 3 3.5 4 4.5 5 5.5 6.5 7 51 54 64 70 86 95 109 125 143 162 186 213 240 51 54 64 70 86 95 109 125 143 162 186 213 240 76 92 108 122 135 148 168 195 220 252 288 330 373 F mm 146 171.4 196.8 235 240 276 312 360 407 458 528 598 680 G mm 133 157 181 221 222 245 280 320 367 418 479 548 620 J mm 9.5 11 12 14.5 11 13.5 14 16 18.5 21 24 26.5 31 Q mm 5 5 6 6 8 8 8 8 8 8 8 8 8 R mm M8 M8 M8 M8 M8 M10 M12 M16 M16 M16 M20 M20 M24 S mm 8 8 8 8 12 12 12 12 12 16 12 16 16 T mm M8 M8 M8 M8 M8 M12 M12 M16 M16 M16 M20 M20 M24 W MAX.X&Y MIN.X mm mm mm 36 39 46 60 81 89 102 118 134 152.7 175 200 226 41 51 64 73 85 95 109 125 143 162 186 213 240 27 27 35 37 50 62 68 80 90 105 120 140 160 MIN.Y mm 27 27 37 40 50 55 65 70 85 105 110 140 160
Max. Speed (rpm) (1) 7200 6300 5400 4500 4480 3860 3450 2975 2650 2380 2050 1830 1600 W1 1.9 2.8 4.5 6.9 8.9
Weight (3)Kg W2 2.0 2.9 4.6 6.0 6.55 W3 Total 2.8 4.3 6.6 10.0 6.7
Inertia (3)Kgm2 J1 J2 J3
Allowable Misalignment (2) Radial (mm) Axial (mm) Conical (degree) 0.8 0.8 0.8 1.2 1.5 1.6 1.6 1.6 1.9 2.1 2.4 2.8 3.3 0.8 1.2 1.2 1.2 1.25 1.5 1.75 2.0 2.25 2.5 2.75 3.25 3.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
10.0 0.004 0.014 0.013 15.7 0.008 0.019 0.025 22.9 0.018 0.049 0.05
11.62 10.92 15.14 37.7 0.050 0.149 0.116 17.74 15.86 21.24 54.8 0.101 0.273 0.194 27.0 24.59 33.03 84.6 0.203 0.560 0.406 40.18 35.34 47.80 123.3 0.392 1.041 0.748 59.5 50.47 69.32 179.3 0.756 1.898 1.345 89.45 77.80 104.63 271.9 1.491 3.867 2.719 132.0 111.96 151.78 395.7 2.872 7.188 4.955 191.11 165.24 222.39 578.7 5.330 13.680 9.565
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. (2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery should be calculated to ensure that these do not exceed the manufacturers allowables. (3) Weights and inertias are calculated with mean bore for couplings up to and including PM600 and with maximum bore for PM900 and above. (4) Oversize shafts can be accommodated in large boss driving flanges, manufactured to customers requirements. (5) PM0.4 - PM3 driving flanges are available with solid bores on request.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 75
900 - 6000
W3 J3 B J J
SxT
W2 J2 QxR
W2 J2 D C D1 W1 J1 Y AF EX D C D1 Y
W1 J1
AF E X
Coupling Size 180 270 400 600 900 1300 1800 2700 4000 6000 A mm 798 925 1065 1195 1190 1330 1490 1685 1925 2210 B mm 554 623 710.5 812 1024 1158 1291 1478 1685 1928 C mm 8 9 10.5 12 11.5 12.5 14 16.5 18.5 21.5 D mm 268 307 350 400 455 515 574 657 749 857 D1 mm 268 307 350 400 455 515 574 657 749 857 E mm 415 475 542 620 706 798 889 1018 1160 1328 F mm 750 865 992 1122 1140 1280 1430 1625 1855 2125 J mm 33.5 36 43 52 26.5 33.5 36 36 43 52 Q mm 12 12 12 24 32 32 32 32 32 32 R mm M24 M30 M36 M36 M24 M24 M30 M30 M36 M42 S mm 20 20 20 24 32 32 32 32 32 32 T mm M24 M36 M36 M24 M24 M30 M30 M36 W mm 252 328 376 569 643 717 821 936 MAX.X&Y MIN.X mm mm 268 307 350 400 455 515 574 657 749 857 167 192 232 285 MIN.Y mm 170 195 235 285 -
M30 288.5
M42 1071
Coupling Size 180 270 400 600 900 1300 1800 2700 4000 6000
Max. Speed (rpm) (1) 1460 1260 1090 975 975 860 770 680 600 520 W1
Inertia (3)Kgm2 J1 J2 J3
Allowable Misalignment (2) Radial (mm) Axial (mm) Conical (degree) 3.5 3.9 4.6 5.2 5.0 5.4 6.1 7.2 8.0 9.3 4.0 4.5 5.25 6.0 5.75 6.25 7 8.25 9.25 10.75 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
28.80 15.35
389.0 414.0 437.3 1240.3 17.88 59.30 29.89 562.4 633.4 651.2 1847 34.03 119.5 60.66 813.3 909.1 946.7 2669.1 65.54 220.2 115.7 1509 629 1229 3367 1280 4057 1765 5691 2582 8347 140 221 388 761 165 392 688 1275 108 184 315 582 1656 1121 2347 1579 3515 2250 5147 3367 7831 5082
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced. (2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery should be calculated to ensure that these do not exceed the manufacturers allowables. (3) Weights and inertias are calculated with mean bore for couplings up to and including PM600 and with maximum bore for PM900 and above. (4) Oversize shafts can be accommodated in large boss driving flanges, manufactured to customers requirements.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 76
Brakedrum
= K1 H =
C A F G Y D1 N
L1 M
L K
V A F
Brakedrums may be used in conjunction with the whole range of PM couplings and may be bolted on either the driving flange or flexible half side of the coupling, the recess - A - locating on the outside diameter of the coupling.
Recommended brake drums for each size of coupling are shown in the table, but V is adjustable to suit Non-standard applications.
Dimensions A B C D1 F G H K K1 L L1 M N P V W MIN.Y MAX.Y Z hp rpm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm 2 2 2 3 3 3 54 171.4 157 15.3 100 90 42 42 55 70 70 90 84 84 84 28 28 28 35 35 35 40 45 45 45 112 250 112 315 112 315 142 400 142 500 142 500 36 46 46 60 81 81 27 27 38 49 50 50 72 72 80 80 51 51 64 73 85 85 109 109 125 125 3 3 3 3 3 3 3 5 5 5 958 187.3 168 730 215.9 178 732 260.3 215 734 260 231 735 260 231 54 171.4 157 20.3 100 110 64 196.8 181 18.7 125 110 70 86 86 235 221 18.9 140 140 240 222 23.5 155 180 240 222 23.5 185 180
180M 12.7 956 187.3 168 180L 16 225L 26 250L 43 280M 63 280L 82
60 105 107 75 120 107 75 120 107 95 135 132 100 155 167 100 155 167 110 170 167
355L 123 590 338 284.5 3.5 400L 170 590 338 324.5 3.5 400LX 228 591 392 341 450L 300 592 392 341 4 4
109 312 280 23.5 205 180 109 312 280 25.5 205 225 125 360 320 125 360 320 26 26 205 225 215 225
172 500 102 212 630 102 212 630 118 212 630 118
The motor ratings are taken for Periodic Duty Classes S4 and S5, 150 starts per hour with a cyclic duration factor at 40%. For motors operating outside these ratings, consult Renold Hi-Tec Couplings
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 77
Dimensions hp 7 10 15 25 35 50 75 100 150 200 275 375 500 rpm A B C D1 F G H K K1 L L1 M N P V W MIN.Y MAX.Y Z mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm 1 2 2 2 3 3 51 146 133 13.5 15.3 15.3 18.7 18.9 18.5 18.5 18.5 21 21 21 21 21 102 121 121 133 171 178 190 216 241 254 305 305 305 83 44.45 76.2 95 50.80 88.9 95 50.80 88.9 70 83 83 31 33 33 35 35 37 45 45 52 40 51 67 67 101 116 116 130 146 148 169 169 189 189 219 245 299 203 254 254 330 330 406 483 483 584 584 584 36 39 39 46 60 81 102 102 118 134 134 22 27 27 38 49 50 72 72 80 92 92 92 41 51 51 64 73 85 109 109 125 143 143 143 162 3 3 3 3 3 3 3 3 5 5 5 5 5 54 171.4 157 54 171.4 157 64 196.8 181 70 86 109 109 125 143 143 143 162 235 240 312 312 360 407 407 407 458 221 222 280 280 320 367 367 367 418
602 603 604 606 608 610 612 614 616 618 620 622
800 161.9 153 725 187.3 172 650 187.3 172 575 215.9 196 525 260.3 219 500 260 237
146 63.50 101.6 95 146 76.20 123.8 111 171 82.55 127 111 222 92.07 158.7 124 222 107.95 158.7 124 286 117.47 181 137 286 127.00 203.2 149 286 149.22 228.6 168 286 158.75 228.6 178 286 177.80 228.6 232
475 338 281.5 3.5 460 338 281.5 3.5 450 392 318 4 410 440 336.5 4.5 390 440 336.5 4.5 360 440 392.5 4.5 340 490 466 5
584 152.7
40
624
Dimensions hp 7.5 10 15 20 30 50 70 100 150 200 250 rpm A B C D1 F G H K K1 L L1 M N P V W MIN.Y MAX.Y Z mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm 1 1 2 2 3 3 3 51 51 146 146 133 133 13.5 15.3 15.3 18.7 18.9 18.5 18.5 18.5 18.5 21 21 102 102 121 121 133 171 178 190 216 241 254 83 44.45 76.2 95 44.45 76.2 95 50.80 88.9 146 50.80 88.9 70 70 83 83 31 31 33 33 35 35 37 45 45 52 40 101 101 116 116 130 146 148 169 169 189 189 203 254 254 330 330 406 406 483 483 584 584 36 36 39 46 60 60 81 102 102 118 134 22 22 27 38 49 49 50 72 72 80 92 41 41 51 64 73 73 85 109 109 125 143 3 3 3 3 3 3 3 3 3 5 5
802 802 803 804 806 808 810 812 814 816 818
800 161.9 153 800 161.9 153 725 187.3 172 650 215.9 182 575 260.3 203 525 260.3 219 500 260 237
54 171.4 157 64 196.8 181 70 70 86 109 109 125 143 235 235 240 312 312 360 407 221 221 222 280 280 320 367
146 63.50 101.6 95 171 76.20 123.8 111 171 82.55 127 111 222 92.07 158.7 124 222 107.95 158.7 124 286 117.47 181 137 286 127.00 203.2 149
475 338 281.5 3.5 460 338 281.5 3.5 450 392 318 4 410 440 336.5 4.5
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 78
PM Technical Data
1.1 Prediction of the system torsional vibration characteristics.
2.2.2
Compare the synthesis value of the calculated heat load in the coupling (PK) at the speed of interest to the Allowable Heat Dissipation (PKW). The coupling temperature rise C = Tempcoup =
An adequate prediction of the system torsional vibration characteristics can be made by the following method.
1.1.1
Use the torsional stiffness as published in the catalogue which is based upon data measured at a 30C ambient temperature.
( )
PK PKW
x 70
1.1.2
Repeat the calculation made as 1.1.1 but using the maximum temperature correction factor St100 and M100 for the rubber selected for both torsional stiffness and dynamic magnifier from the table below. CT100 = CT30 x St
1.2.4
Calculate the coupling temperature as per 1.2. Repeat calculation until the coupling temperature agrees with the correction factors for torsional stiffness and
Rubber Grade SM 60 SM 70 SM 80
1.3 1.4
Temperature Correction Factor St
SM 60 is considered standard Rubber Grade Dynamic Magnifier at 30C (M30) 8 6 4 Dynamic Magnifier at 100C (M100) 10.67 9.53 6.9
SM 60 SM 70 SM 80
SM 60 is considered standard
1.1.3
Review the calculations 1.1.1 and 1.1.2 and if the speed range is clear of criticals which do not exceed the allowable heat dissipation value as published in the catalogue, the coupling is then considered suitable for the application with respect to the torsional vibration characteristics. If there is a critical in the speed range the actual temperature of the coupling will need to be calculated.
RUBBER TEMPERATURE C
Factor
The Dynamic Magnifier of the rubber is subject to temperature variation in the same way as the torsional stiffness.
1.2
T =30 x St
Relative Damping
1.2.1
30
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 79
Radial Stiffness (N/mm) @ No Load 685 723 1240 2050 6276 6966 7980 9140 10460 11069 12680 14500 16400 1070 1130 1950 3240 8400 9320 10680 12230 14000 15960 18280 20916 23646 1740 1820 3210 5190 11400 12650 14500 16600 19000 21660 24810 28200 32100 @ 50% Tkmax SM80 2510 2650 4480 7450 16500 18320 20980 24000 27500 31350 35910 41100 46450 1430 1510 2600 4300 13180 14630 16780 19200 21970 25050 28700 32820 37110 1760 1860 3200 5240 13800 15320 17550 20100 23000 26220 30040 34360 38850 458 502 714 970 1060 1176 1347 1543 1766 2010 2306 2638 2980 SM60 SM70 SM80 SM60 SM70
Axial Stiffness (N/mm) @ No Load SM60 SM70 SM80 753 828 1180 1610 2748 3050 3495 4000 4580 5220 5980 6840 7740 1040 1160 1670 2230 4120 4573 5240 6000 6867 7828 8968 10260 11600 @ 50% Tkmax 920 1050 1540 2020 2300 2500 2920 3310 3830 4360 4980 5720 6460 1100 1360 1920 2610 2750 3050 3500 4000 4580 5220 5980 6840 7740 1250 1450 2060 2750 4120 4570 5240 6000 6870 7830 8970 10260 11600
Max. Axial Force (N) @ 50% Tkmax (1) 66 72 102 128 1501 1668 1913 2178 2502 2845 3267 3728 4218 78 80 112 140 1648 1825 2099 2374 2747 3139 3581 4101 4640 85 106 148 185 2237 2482 2845 3257 3728 4265 4866 5572 6298
(1 The couplings will slip axially when the maximum axial force is reached. (2) At 10Hz only, allowable vibratory torque at higher or lower frequencies fe = Vib. Torque (3) These values should be corrected for rubber temperature as shown in the design information section
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 80
Coupling Size SM60 180 270 400 600 900 1300 1800 2700 4000 6000 3.120 4.680 6.933 10.40 @ 0.25 TKN SM70 4.440 6.660 9.867 14.80 8.1 11.7 16.2 24.3 36.0 54.0 SM80 5.760 8.640 12.80 19.20 9.45 13.65 18.9 28.4 42.0 63.0 SM60 4.440 6.660 9.768 14.80 -
Dynamic Torsional (3) Stiffness (MNm/rad) @ 0.50 TKN SM70 5.940 8.910 13.20 19.80 11.7 16.9 23.4 35.1 520 78.0 SM80 7.740 11.61 17.20 25.80 16.2 23.4 32.4 48.6 72.0 108.0 SM60 6.600 9.600 14.67 22.0 @ 0.75 TKN SM70 8.520 12.78 18.93 28.40 17.3 25.0 34.7 52.0 77.0 115.5 SM80 11.34 17.01 25.20 37.80 20.9 30.2 41.9 62.8 93.0 139.5 SM60 9.600 14.40 21.33 32.00 @ 1.0 TKN SM70 11.88 17.82 26.40 39.60 23.6 34.1 47.2 70.9 105.0 157.5 SM80 16.38 24.57 36.40 54.60 26.8 38.7 53.5 80.3 119.0 178.5
Coupling Size 180 270 400 600 900 1300 1800 2700 4000 6000
Radial Stiffness (N/mm) @ No Load 18270 20920 23820 27300 26350 30170 34340 39370 28174 31837 35501 40661 46337 35750 40945 46600 53400 46048 52035 58024 66458 75735 @ 50% Tkmax SM80 51760 59260 67460 77330 41350 47350 53890 61780 43290 49560 56420 64680 3324 3800 4332 4966 SM60 SM70 SM80 SM60 SM70
Axial Stiffness (N/mm) @ No Load SM60 SM70 SM80 8620 9870 11230 12880 1234 1395 1555 1781 2029 3044 12924 14800 16844 19310 1966 2222 2477 2837 3233 4849 @ 50% Tkmax 7200 8240 9380 10760 8620 9870 11230 12880 12920 14800 16840 19310 -
Max. Axial Force (N) @ 50% Tkmax (1) 4709 5396 6131 7034 5160 5915 6730 7720 7014 8025 9143 10477 -
69505 113601
(1) The couplings will slip axially when the maximum axial force is reached. (2) At 10Hz only, allowable vibratory torque at higher or lower frequencies fe = Vib. Torque (3) These values should be corrected for rubber temperature as shown in the design information section
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 81
Dynamic Torsional (3) Stiffness (MNm/rad) @ 0.50 TKN SM70 0.104 0.155 0.233 0.345 0.52 1.05 1.517 2.1 3.15 4.667 7 SM80 0.159 0.239 0.358 0.53 0.796 1.193 1.724 2.387 3.58 5.304 7.956 SM60 0.168 0.251 0.337 0.559 0.84 1.154 1.667 2.308 3.462 5.129 7.693 @ 0.75 TKN SM70 0.162 0.243 0.364 0.539 0.809 1.317 1.902 2.634 3.951 5.853 8.78 SM80 0.214 0.321 0.481 0.713 1.069 1.603 2.316 3.207 4.81 7.126 10.689 SM60 0.285 0.427 0.641 0.948 1.424 1.91 2.759 3.82 5.73 8.489 12.733 @ 1.0 TKN SM70 0.256 0.385 0.577 0.855 1.282 1.85 2.672 3.7 5.55 8.222 12.333 SM80 0.328 0.491 0.737 1.092 1.638 2.457 3.549 4.913 7.37 10.919 16.378
Radial Stiffness (N/mm) @ No Load SM70 3742 4286 4905 5592 6425 7333 8284 9236 10570 12050 13798 SM80 6138 7030 8044 9170 10538 12025 13586 15147 17335 19770 22628 SM60 9510 10900 12470 14215 16300 18640 21000 23480 26870 30650 35070 @ Tkn SM70 9056 10374 11870 13530 15550 17745 20048 22350 25580 29176 33390 SM80 9132 10460 11968 13644 15678 17892 20214 22535 25790 29410 33666 SM60 1122 1285 1470 1675 1925 2198 2482 2768 3168 3613 4135
Axial Stiffness (N/mm) @ No Load SM70 1495 1710 1960 2234 2568 2930 3310 3690 4220 4818 5514 SM80 2545 2915 3335 3800 4368 4986 5632 6278 7187 8197 9380 SM60 2918 3340 3825 4360 5010 5718 6460 7200 8242 9400 10750 @ Tkn SM70 3067 3510 4020 4580 5266 6000 6790 7570 8660 9880 11300 SM80 3218 3686 4218 4808 5526 6306 7124 7942 9090 10368 11865
@ Tkn (1) SM60 2943 3335 3728 4415 5003 5690 6475 7161 8240 9418 10791
(1) The couplings will slip axially when the maximum axial force is reached for SM60, SM70 and SM80 grades of rubber. (2) At 10Hz only, allowable vibratory torque at higher or lower frequencies fe = Vib. Torque 10Hz fe (3) These values should be corrected for rubber temperature as shown in the design information section RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 82
PM Design Variations
The PM coupling range can be adapted to meet customer needs. Below are some of the arrangements that have been produced. For a more comprehensive list contact Renold Hi-Tec Couplings.
Cardan shaft coupling used to increase the distance between shaft ends and give a higher misalignment capability.
Cardan shaft coupling with thrust bearings to support the drive line on vertical applications.
Combination with a torque limiting device to prevent damage to driving and driven machine under shock loads.
Coupling with a brake disc for use on cranes, fans and conveyor drives.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 83
Service factor:
Driven equipment:
(see page 87)
Service factor:
Continuous power: Operating speed: Driving shaft diameter: Driving shaft length: Flywheel location diameter: Continuous misalignment: Diameter constraints: Distance between shaft ends:
Maximum power: Overspeed: Driven shaft diameter: Driven shaft length: Hole size and PCD: Transient misalignment: Length constraints:
If you require help with coupling selections contact Renold Hi-Tec Couplings: Tel: +44 (0) 1422 255000 Fax: +44 (0) 1422 255100
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 84
Selection Procedure
G From the continuous Power (P) and operating Speed (n) calculate the Application Torque T norm from the formula: TNORM TMAX TKN = TNORM = 9549 x (P/n) Nm G Select Prime Mover Service Factor (Fp) from section 3.0. G Select Driven Equipment Service Factor (Fm) from section 4. G The minimum Service Factor has been set at 1.5. G Calculate TMAX from the formula: n Fp TMAX = TNORM (Fp + Fm) G Select Coupling such that TMAX < TKMAX G Check n < Coupling Maximum Speed (from catalogue data). G Check Coupling Bore Capacity such that dmin < d < dmax. G Consult the factory for alternatives if catalogue limits are exceeded. N.B. If you are within 80% of maximum speed, dynamic balancing is required. Fm dmax dmin = = = = = TKmax P = = = = Application Torque (Nm) Peak Application Torque (Nm) Nominal Coupling Rating according to DIN 740 (kNm)
(with service factor = 3 according to Renold Hi-Tec Couplings standard)
Maximum Coupling Rating according to DIN 740 (kNm) Continuous Power to be transmitted by coupling (kW) Speed of coupling application (rpm) Prime Mover Service Factor Driven Equipment Service Factor Coupling maximum bore (mm) Coupling minimum bore (mm)
It is the responsibility of the system designer to ensure that the application of the coupling does not endanger the other constituent components in the system. Service factors given are an initial selection guide.
For confirmation of coupling selection complete the check list on page 87 and fax to Renold Hi-Tec Couplings. Fax: +44 (0) 1422 255100
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 85
Application
Application
Agitators Pure liquids Liquids and solids Liquids-variable density Blowers Centrifugal Lobe (Rootes type) Vane Brewing and Distilling Bottling machinery Lauter Tub Briquetter Machines Can filling machines Cane knives Car dumpers Car pullers - Intermittent Duty Clay working machinery Compressors Axial Screw Centrifugal Lobe Reciprocating - multi-cylinder Rotary
Generators Alternating Not welding Welding Hammer mills Lumber industry Barkers - drum type Edger feed Live rolls Log haul-incline Log haul-well type Off bearing rolls Planer feed chains Planer floor chains Planer tilting hoist Sawing machine Slab conveyor Sorting table Trimmer feed Metal Manufacture Bar reeling machine Crusher-ore Feed rolls Forging machine Rolling machine Roller table Shears Tube mill (pilger) Wire Mill Metal mills Drawn bench - carriage Drawn bench - main drive Forming machines Slitters Table conveyors - non-reversing - reversing Wire drawing and flattening machine Wire winding machine Metal rolling mills Blooming mills Coilers - hot mill & cold mill Cold mills Cooling mills Door openers Draw benches Edger drives Feed rolls, reversing mills Furnace pushers Hot mills Ingot cars Manipulators Merchant mills Piercers Pushers rams Reel drives Reel drums Bar mills Roughing mill delivery table Runout table Saws - hot, cold Screwdown drives Skelp mills Slitters Slabbing mills Soaking pit cover drives Straighteners Table transfer & runabout Thrust block Traction drive Tube conveyor rolls Unscramblers Wire drawing Mills, rotary type Ball Cement kilns Dryers and coolers Kilns Hammer Pebble Pug Rod Tumbling barrels Mining Conveyor - armoured face
- belt - bucket - chain - screw Dintheader Fan - ventilation Haulages Lump breakers Pulverisor Pump - rotary - ram - reciprocating - centrifugal Roadheader Shearer - Longwall Winder Colliery Mixers Concrete mixers Drum type Oil industry Chillers Oil well pumping Paraffin filter press Rotary kilns
Conveyors - uniformly loaded or fed Apron 2.0 Assembly 1.5 Belt 1.5 Bucket 2.0 Chain 2.0 Flight 2.0 Oven 2.5 Screw 2.0 Conveyors - heavy duty not uniformly fed Apron Assembly Belt Bucket Chain Flight Oven Reciprocating Screw Shaker Crane & hoists All motions Crushers Ore Stone Sugar (1) Dredgers Cable reels Conveyors Cutter head drives Jig drives Manoeuvering winches Pumps Screen drive Stackers Utility winches Dynamometer Elevators Bucket Centrifugal discharge Escalators Freight Gravity discharge Fans Centrifugal Cooling towers Forced draft Induced draft (without damper control) Feeders Apron Belt Disc Reciprocating Screw
2.0 2.0 2.0 2.5 2.5 2.5 2.5 3.0 3.0 4.0 3.0 3.0 3.5 3.5 2.5 2.0 3.5 3.5 3.0 3.0 3.0 3.0 2.0 1.5 3.0 2.0 1.5 2.0 2.0 1.5 2.0 2.0 2.0 2.0 2.0 2.0 3.0 2.0
Paper mills Barker-auxiliaries hydraulic 3.0 Barker-mechanical 3.5 Barking drum (Spur Gear only) 3.5 Beater and pulper 3.5 Bleacher 2.0 Calenders 2.0 Chippers 2.5 Coaters 2.0 Converting machine (not cutters, platers) 2.0 Couch 2.0 Cutters, platers 3.0 Cylinders 2.0 Dryers 2.0 Felt stretcher 2.0 Felt whipper 2.0 Jordans 2.25 Line shaft 2.0 Log haul 2.5 Presses 2.5 Pulp grinder 3.5 Reel 2.0 Stock chests 2.0 Suction roll 2.0 Washers and thickeners 2.0 Winders 2.0 Printing presses Propellors Marine - fixed pitch - controllable pitch Pullers Barge haul Pumps Centrifugal Reciprocating - double acting single acting - 1 or 2 cylinders 3 or more cylinders Rotary - gear, lobe, vane Rubber industry Mixed - banbury Rubber calender Rubber mill (2 or more) Sheeter Tyre building machines Tyre and tube press openers Tubers and strainer Screens Air washing Grizzly Rotary, stone or gravel Travelling water intake Vibrating Sewage disposal equipment Textile industry Windless 2.0 2.0 2.0 2.5 1.5 3.0 3.0 3.0 2.0 3.0 2.0 2.5 2.5 2.5 2.0 2.5 1.5 2.5 2.0 1.5 2.5 2.0 2.0 2.5
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 86
Selection Examples
Example 1
G Selection of 6 Cylinder Diesel Engine 750 kW at 900 rpm
Example 2
G Selection of Induction Motor 800 kW at
driving a Centrifugal Pump. The coupling is flywheel mounted Pump shaft diameter = dm P dm Fp = = = = = T MAX = = = 750 kW 95 mm 1.7 n temp Fm = = = 900 rpm 30C 1.5
TNORM =
(P/n) x 9549 Nm (750/900) x 9549 Nm 7.958 kNm T NORM (Fp + Fm) 7.958 (1.7 + 1.5) 25.466 kNm
G
Motor shaft = dp Pump shaft = dm P = 800 kW n = 1498 rpm dp = 95 mm dm = 85 mm temp = 30C Fp = 0 Fm = 2 T NORM = (P/n) x 9549 Nm = (800/1498) x 9549 Nm = 5.1 kNm T MAX = T NORM (Fp + Fm) = 5.1 (0 + 2) kNm = 10.2 kNm The application requires a steel coupling (by customer specification) and PM type coupling should be selected. Examination of PM catalogue shows PM12 as: T Kmax = 12 kNm which satisfies the condition
G G G G
coupling should be selected. Examination of RB catalogue shows RB 3.86 as: T Kmax = 27.4 kNm T KN = 9.159 kNm
T MAX < T Kmax (10.2 < 12.0) kNm n < Coupling Maximum Speed (1498 < 3450) rpm dmin < dp < dmax (72 < 95 < 109) mm dmin < dm < dmax (72 < 85 < 109) mm
Calculation Service
G For over 40 years we have been the world leader in torsional G A consultancy service is also available to customers in the
vibration analysis for all types of machinery and have developed sophisticated in-house computer programmes specifically for this purpose.
engineers have made many torsional vibration analyses. For example, steady state transient and Torque Amplification Factors (TAF) on electric motor drivelines in cement mills, rolling mills, compressor drive trains, synchronous motor start ups and variable frequency (LCI, Kramer/Scherbius/PWM) applications.
G On page 91, two examples of torsional vibration analysis that
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 87
Transient Analysis
Calculated Examples
Illustrated below are two different types of transient torsional vibrations analysis that can be produced by Renold Hi-Tec Couplings engineers. This ensures optimum solutions are reached by the correct selection of torsional stiffness and damping characteristics of the coupling. Whilst the synchronous resonance and synchronous convertor (LCI) examples are shown, other applications Renold Hi-Tec Couplings has experience of include Torque Amplification, electrical speed control devices, PWM, Scherbius/Kramer, short-circuit and any reconnection of electrical circuits on the mechanical systems.
Example 2
From 1981 we have been engineering flexible couplings for Synchronous Convertor (LCI) drives to control the forced mode conditions through the first natural frequency by judicial selection of torsional stiffness and damping.
Table C
Speed - RPM Coupling Torque Nm *10**2 320 180 160 140 0 100 -160 60 -320 20 .250 .750 1.250 1.750 2.250 2.750 Acceleration time in seconds 3.250 3.750
Example 1
Since June 1962 we have engineered flexible couplings for Synchronous Motor applications to reduce by damping, the damaging vibratory torques imposed into the system when accelerating through the first resonant frequency.
Table C shows a typical motor/fan system connected rigidly (or through a gear or membrane coupling) when damaging torques would have been experienced in the motor shaft.
Table A
Speed - RPM
Table D
Speed - RPM Coupling Torque Nm *10**2 1.500 4.500 7.500 10.500 13.500 16.500 19.500 22.500 Acceleration time in seconds 1201620 601260 0 900 -60 540 320 180 160 140 0 100 -160 60 -320 20 .250 .750 1.250 1.750 2.250 2.750 Acceleration time in seconds 3.250 3.750
Table A shows vibrating torque experienced in the motor shaft when the system is connected rigidly (or by a gear or membrane coupling) to the driven system.
-120 180
Table D shows the equivalent Renold Hi-Tec Couplings engineered solution using a PM coupling.
Table B
Speed - RPM Coupling Torque KNm 1201620 601260 0 900 -60 540
-120 180 1.500 4.500 7.500 10.500 13.500 16.500 19.500 22.500 Acceleration time in seconds
Table B shows the same system connected by a DCB coupling. A PM type coupling is also used in such applications.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 88
Rubber Information
The rubber blocks and elements used in Renold Hi-Tec Couplings are key elements in the coupling design. Strict quality control is applied in the manufacture, and frequent testing is part of the production process.
Rubber-in-Compression
These designs use non-bonded components, which allows for many synthetic elastomers to be employed. These elastomers offer considerable advantages over others for specific applications, giving Renold Hi-Tec Couplings a distinctive lead in application engineering in specialised areas.
Rubber in Shear
These designs use high tear strength, low creep natural rubber developed for diesel engine drives. All rubber in shear couplings are 100% tested to ensure bond/moulding integrity.
Rubber Compound
Natural Identification label Resistance to Compression Set Resistance to Flexing Resistance to Cutting Resistance to Abrasion Resistance to Oxidation Resistance to Oil & Gasoline Resistance to Acids Resistance to Water Swelling Service Temp. Maximum; Continuous Service Temperature Minimum * High Damping Red (F, NM) Good Excellent Excellent Excellent Fair Poor Good Good 80C -50C StyreneButadiene Green (SM) Good Good Good Good Fair Poor Good Good 100C -40C Neoprene Yellow (CM) Fair Good Good Good Very Good Good Fair Good 100C -30C Nitrile White (AM) Good Good Good Good Good Good Fair Good 120C -40C StryeneButadiene Blue* (S) Fair Good Fair Good Fair Poor Good Good 100C -40C
SM
CM
Renold 40
AM
Renold 45
Renold 45
Renold 45
RB
SM/SB
Renold 50 Renold 60 Renold 50 Renold 60 NCB A1976/7 Renold 50 Renold A833/7 Renold 60 Renold 60 Renold 60 S19 Renold 50 Renold 50 S12
SPECIAL
WB
Renold 70 Renold 80
Renold 70 Renold 80
Renold 70 Renold 80
Renold 70 Renold 80
Renold 70 Renold 80
S28
S33
Renold 90
Renold 90
Renold 90
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 89
Damping Characteristics
Coupling damping varies directly with torsional stiffness and inversely with frequency for a given rubber grade. This relationship is conventionally described by the dynamic magnifier M, varying with hardness for the various rubber types. M= K C This property may also be expressed as the Damping Energy Ratio or Relative Damping, which is the ratio of the damping energy, AD, produced mechanically by the coupling during a vibration cycle and converted into heat energy, to the flexible strain energy Af with respect to the mean position.
) ae (k + ic
it +
Where
C K
= Frequency (Rad/s)
M = Dynamic Magnifier
tan
= C K
I M
M 15 10 8 6 4
Deflection
AD Af
2 M
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 90
Product Range
The products comprise of rubber in compression and rubber in shear couplings, developed over 40 years for the complete range of diesel and industrial applications. RENOLD Hi-Tec Couplings deliver the durability, reliability and long life that customers demand. In particular our design capability and innovation is recognised in customising couplings to meetexacting requirements. RENOLD Hi-Tec Couplings is the complete solution.
RB Range
General purpose, cost effective range available in either shaft to shaft or flywheel to shaft configurations with a maximum torque of 41 kNm.
Applications G Generator and Pump Sets G Compressors G Metal manufacture G Bulk Handling G Pulp and Paper Industry G General Industrial Applications Benefits G Control of Resonant Torsional Vibration G Intrinsically Fail Safe Operation G Maintenance Free G Zero Backlash G Lowest Lifetime Cost G Misalignment Capability
PM Range
This range of couplings is specially designed for heavy industrial applications providing exceptional protection against severe shock loads and vibration. Maximum torque 6000 kNm.
Applications G Metal manufacture G Mining G Pumps, Fans and Compressors G Cranes and Hoists G Power Generation G Pulp and Paper Industry G General Heavy Duty Industrial Applications Benefits G Severe Shock Load Protection G Intrinsically Fail Safe Operation G Maintenance Free G Vibration Control G Zero Backlash G Misalignment Capability G Lowest Lifetime Cost
DCB Range
The unrivalled quality and endurance capability designed into every DCB coupling make it ideally suited for marine propulsion, power generation and reciprocating compressor applications where long life, fail safe operation and control of resonant torsional vibrations are essential. Maximum torque range 5520 kNm.
Applications G Marine Propulsion G High Power Generator Sets G Reciprocating Compressors Benefits G Control of Resonant Torsional Vibration G Intrinsically Fail Safe Operation G Long Life G Misalignment Capability G Zero Backlash G Severe Shock Load Protection
MSC Range
This innovative coupling has been designed to satisfy a vast spectrum of diesel drive and compressor applications providing low linear stiffness and control of resonant torsional vibration with intrinsically fail safe operation. Maximum torque 375 kNm.
Applications G Marine Propulsion G High Power Generator Sets G Compressors Benefits G Low Linear Stiffness G Intrinsically Fail Safe Operation G Control of Resonant Torsional Vibration G High Heat Capacity G Large Misalignment Capability G Noise Attenuation G Radial Removal of Rubber Elements
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 91
Product Range
LKB Range
The LKB coupling has been designed as a low stiffness, blind assembly coupling for connecting diesel engines to driven equipment in a broad range of applications. Maximum torque 30 kNm.
Applications G Marine Propulsion G High Power G Compressors G Pumps Benefits G Unique Blind Assembly G Control of Resonant Torsional Vibration G Low Linear Stiffness G Noise Attenuation G Zero Backlash
HTB Range
The HTB Coupling is a high temperature, blind assembly coupling designed for mounting inside bell housings. Maximum torque 60 kNm
Applications G Marine Propulsion G Compressors G Generators and pump sets G Rail Traction Benefits G Unique blind assembly G High temperature capacity (up to 200C) G Severe shock load protection G Intrinsically fail safe G Noise attenuation
Special Couplings
Renold Hi-Tec Couplings has a unique capability to design and manufacture special couplings. Finite element analysis, computer modelling and extensive testing facilities can be used to design and manufacture couplings to suit all applications. Extensive rubber manufacturing expertise allows couplings with special properties to be made, from fire resistant materials to highly elastic noise attenuating compounds.
Coupling type
G Universal joint shaft coupling G Limited end float coupling G Torque limiting couplings G Clutch couplings G Disc and drum brakes G Aluminium coupling G Cardan shaft coupling
Benefits
G Introduces torsional flexibility while accepting the sinusoidal loads from the UJ shaft G Limits the axial movement on machines without axial location G Protects driving and drive machines from shock and overload torques G Allows the drive to be engaged and disengaged easily G Allows the drive to be slowed, stopped or held in position G Anti-magnetic and lightweight G Gives high misalignment capability and gives increased distance between shaft ends
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 92
FLEXIBLE COUPLINGS
SPRAG CLUTCHES
WORM GEARS
HELICAL GEARS
VARIABLE SPEED
INDEXERS
WHEN IT COMES T OMES TO AVAILABILITY, VAILABILITY, WOULD R IGHT AWAY OULD IGHT WAY BE SOON ENOUGH? NOUGH?
The Power Transmission Solution
RENOLD CLUTCHES & COUPLINGS Wentloog Corporate Park Newlands Road Cardiff CF3 2EU Telephone: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20791360 http://www.renold.com
Did you know Renold make the widest range of couplings? Stocked by all major distributors, over 300 outlets throughout the country. Manufactured in the UK to Renolds stringent specifications its never too soon to get your hands on the UKs most available range of couplings.
93
BELGIUM
Renold Continental Ltd Alle Verte 1,1000 Brussel. Tel: +32 (0) 2 2011262 Fax: +32 (0) 2 2032210 Email: info@renold.be
EL SALVADOR
MVA & Cia Residencial San Luis, Avenida 4 #45 Block 2, San Salvador, El-Salvador, Central America Tel: + 503 274 649
SOUTHERN IRELAND
Henry R. Ayton Ltd., Broomhill Drive, Tallagh, Dublin 24 Tel: + 353 (0) 1 4517922 Fax: + 353 (0) 1 4517922
ISRAEL
Technica J. Bokstein Co. Ltd, 3 Hatrupa Street, Netanya 42504 Tel: + 972 9 8850505 Fax: + 972 36131074
CANADA
Renold Canada Ltd 121 Roy Boulevard, Brantford, Ontario, N3T 5N4 Toll Free: 1-800-265-9970 Tel: +1 519 756 6118 Fax: +1 519 756 1767 Email: inquiry@renoldcanada.com 622 rue De Hull, Ville La Salle, Quebec, H8R 1V9. Toll Free: 1-800-361-1414 Tel: +1 514 367 1764 Fax: +1 514 367 4993
FINLAND
Kraftmek Oy, Hitsaajankatu 9, P.O. Box 36, FIN-00811 Helsinki Tel: + 358 9 7557355 Fax: + 358 9 7550414
AUSTRALIA
Renold Australia Proprietary Ltd 508-520 Wellington Road, Mulgrave, Victoria 3170, Mulgrave North Tel: +61 (0) 3 9262 3333 Fax: +61 (0) 3 9561 8561 Branch Tel: +61 (0) 3 9262 3355 Email: melcag@renold.com.au Unit 1, 12-18 Victoria Street, Lidcombe, Sydney, NSW 2141. Tel: +61 (0) 2 9649 3122 Fax: +61 (0) 2 9646 1295 Email: nswsales@renold.com.au Unit 10, 31 Boyland Avenue, Coopers Plains, Brisbane, Queensland 4108. Tel: +61 (0) 7 3275 2155 Fax: +61 (0) 7 3875 1779 Corner Orsmond & George Sts. Hindmarsh, Adelaide, South Australia 5007. Tel: +61 (0) 8 8346 9077 Fax: +61 (0) 8 8340 1217 Unit 2, 127 Grandstand Street, Belmont, Perth, West Australia 6104. Tel: +61 (0) 8 9479 1388 Fax: +61 (0) 8 9479 1364 Unit 13 56 Industrial Drive, Mayfield, NSW 2304 Tel: +61 (0) 2 4960 8440 Fax: +61 (0) 2 4960 8455 PO Box 159, Unanderra, Wollongong, NSW 2526. Tel: +61 (0) 2 42 621771 Fax: +61 (0) 2 42 621772 Shop B, 247 Ingham Road, Garbutt, Townsville, QLD 4814. Tel: +61 (0) 7 4779 5922 Fax: +61 (0) 7 4775 1446
ITALY
Bianchi Cuscinetti SpA Via Zuretti, 102, 20125 Milano, Tel: + 39 02 67861 Fax: + 39 02 66981669
FRANCE
Brampton Renold, Zone Industrielle A, Rue de la Pointe, BP 359, 59473 Seclin Cedex. Tel: +33 (0) 320 16 29 29 Fax: +33 (0) 320 16 29 00 Renold Automotive (Chain only) Brampton Renold S/A, 188 Boulevard Lafayette BP 99, 62102 Calais Cedex Tel: +33 (0) 321 97 99 45 Fax: +33 (0) 321 97 83 45
JAMAICA
Masterton Ltd, 21-25 Hanover Street, P.O. Box 73 Kingston. Tel: + 18 767 540557 Fax: + 18 769 227807
CHILE
Sargent S.A., Avda. Presidente Bulnes No 205, Casilla 166-D, Santiago - Chile. Tel: (56 2) 510 3000 Fax: (56 2) 698 3989 Email: secventas@sargentagricola.cl
KOREA
S.S. Corporation, Yeouido, P.O. Box 60, Seoul. Tel: 00-822-783-6829 Fax: 00-822-784-9322 Email: sslcorp@chollian.net
GERMANY
Arnold & Stolzenberg, Juliusmhle, D37574 Einbeck. Postal address: PO Box 1635 + 1645 D37557 Einbeck. Tel: +49 (0) 5562 81 163 Fax: +49 (0) 5562 81 164 Email: arnoldandstolzenberg @t-online.de
CHINA
Rm210C, Heqiao Building Guanghua Rd, No.8 (Jia), Chaoyang Dist, Beijing Postcode 100020, China. Tel: +86 10 65817522 Fax: +86 10 65810336 Email:renoldcn@public3.bta.net.cn
MALAYSIA
Renold (Malaysia) SDN BHD, 39 Jalan TP 7/7, Sime UEP Industrial Park, Section 26, 40400 Shah Alam, Selangor. Tel: + 603-5191 9880 Fax: + 603-5191 9881 (General) Fax: + 603-5191 6881 (Sales) Email: malaysia@renold.com 201, Jalan Simbang, Taman Perling, 81200 Joho Bharu, Johor, Malaysia. Tel: + 60 (0) 7 2384152-3 Fax: + 60 (0) 7 2384155 Email: malaysia@renold.com 452, Jalan Kuala Kangsar, Loke Lim Garden, 30010 Ipoh, Perak, Malaysia. Tel: + 60 (0) 5 2915991-2 Fax: + 60 (0) 5 2915728 Email: malaysia@renold.com 28B Jalan Perai Jaya 3, Bandar Perai Jaya,13600 Perai, Penang, Malaysia Tel: + 604-399 9648 Tel: + 604-399 0648 Fax: + 604-399 5649 Email: malaysia@renold.com
COLOMBIA
Transmission de Potencia SA Carrera 68B No10 - 98 Apartado Aereo 6794 Santafe de Bogato DC Tel: + 571 2600100 Fax: + 571 2904823 Importadora Casa Sueca Ltda., Calle 52, No. 1N-74, Apartado Aereo 1208, Cali. Tel: 00 57 2346 4455 Fax: 00 57 2346 4967
GREECE
Provatas Engineering 53/47 Dragatsaniou St, 185 - 45 Piraeus. Tel: + 30 1 4170266 Fax + 30 1 4170253
HOLLAND
Renold Continental Ltd, Jarmuiden 30c, 1046 AD Amsterdam. Tel: +31 (0) 20 614 6661 Fax: +31 (0) 20 614 6391 Email: info@renold.nl
CZECH REPUBLIC
Renold GesmbH Technical Office, Dipl. Ing. R. Badura, Jaroslavice 129, CZ-76001 Zlin. Tel: +42 67 7211074 Fax: +42 67 7211074
HUNGARY
Renold GesmbH Technical Office, Ing. Havasi Janos, Ret Utca 25, H-6200 Kiskrs. Tel: +36 (0) 78 312483 Fax: +36 (0) 78 312483
DENMARK
Renold A/S, Skelmarksvej 6, Postboks 90, 2605 Brndby. Tel: +45 43 452611 Fax: +45 43 456592 Email: renold@post9.tele.dk
INDIA
Voltas Limited., Machine Tool Division, Voltas House B, 3rd Floor, TB Kadam Marg, Chinchpokli, Mumbai 400033 Tel: 091 22 370 0829 Fax: 091 22 371 4889 Email: mshaik@voltasltd.com
AUSTRIA
Renold GmbH Obere Donaustrasse 43, Postfach 60, A-1021 Wien. Tel: +43 (0) 1 3303484 0 Fax: +43 (0) 1 3303484 5
MAURITIUS
Dynamotors Ltd, P.O. Box 733, Bell Village, Tel: + 230 2122847/8/9 Fax: + 230 2088348
EGYPT
Itaco, Intl for Trading & Agency, P.O. Box 7550, Nasr City, Cairo. Tel: + 20 2 2718036 Fax: + 20 2 2878089
MEXICO
Accessorios Automotrices y Rodamientos Industriales, S.A. de C.V., Calz Legaria 833-A Col Irigacion, Mexico DF 11500 Tel: + 52 5 395 6300 Fax: + 52 5 395 6370
BANGLADESH
Brady & Co (Bangladesh) Ltd, 31, Bangabandhu Avenue, Dhaka-1000 Tel: + 880 2802358 Fax: + 880 2802358
NORTHERN IRELAND
Henry R. Ayton Ltd, Derriaghy, Dunmurry, Belfast. Tel: 01232 618511 Fax: 01232 602436
94
SOUTH AFRICA
Renold Croft (Pty) Limited, Corner Liverpool and Bolton Streets, Nestadt Industrial Sites, Benoni, 1501 Postal Address: Private Bag x 030, Benoni, 1500. Tel: + 27 (0) 11 845 1535 Fax: + 27 (0) 11 421 9289 E-mail: renold@iafrica.com 89 Berea Road, Dalbridge, Durban, 4000, Postal Address: PO Box 18137, Dalbridge, Durban, 4014. Tel: + 27 (0) 31 305 5281 Fax: + 27 (0) 31 304 7961 364 Voortrekker Road, Maitland, Cape Town, 7405 Postal Address: PO Box 211, Maitland, 7405. Tel: + 27 (0) 21 593 8913 Fax: + 27 (0) 21 593 8930 137 Kempston Road, Port Elizabeth, 6000. Postal Address : PO Box 4080, Korsten, 6014. Tel: + 27 (0) 41 453 2430 Fax: + 27 (0) 41 451 4305 5c van Bruggen St.Ext 25 Witbank, 1035, Postal Address: PO Box 2661, Witbank, 1035. Tel: + 27 (0) 13 692 7760 Fax: + 27 (0) 13 697 0546 9 Macgra Industrial Park, Cnr. Alumina Allee & Bronze Bar, Altron, Richards Bay, 3900, Postal Address: PO Box 21247, Arboretum, 3900. Tel: + 27 (0) 351 51 1093-1049 Fax: + 27 (0) 351 51 1315
SWITZERLAND
Renold (Switzerland) Gmbh, Ringstrasse 16, Postfach 1115 CH-8600 Dbendorf 1. Tel: + 41 (0) 1 824 8484 Fax: + 41 (0) 1 824 8411 E-mail: info@renold-gmbh.ch Route De Prilly 25, CH-1023 Crissier. Tel: + 41 (0) 21 632 9460 Fax: + 41 (0) 21 632 9475 E-mail: crissier@renold-gmbh.ch
Renold Clutches & Couplings Wentloog Corporate Park, Newlands Road, Cardiff CF3 2EU, Wales Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 (Sales):+ 44 (0) 29 20791360 E-mail: couplings@cc.renold.com Web: www.renold.com Renold Hi-Tec Couplings 112 Parkinson Road Halifax HX1 3QH Tel: +44 (0) 1422 255000 Fax: +44 (0) 1422 320273 E-mail: sales@hitec.renold.com Web: www.renold.com Holroyd Harbour Lane North, Milnrow, Rochdale, OL16 3LQ. Tel: +44 (0) 1706 526 590 Fax: +44 (0) 1706 353 350 E-mail: info@holroyd.com Web: www.holroyd.com Renold Chain UK Sales, Horninglow Road, Burton upon Trent, Staffordshire, DE14 2PS. Tel: +44 (0) 1283 512 940 Fax: +44 (0) 1283 512 628 E-mail: enquiry@renold.com
THAILAND
United Power Engineering Co Ltd 4 Soi Sukhumvit 81 (Siripot) Sukhumvit Road Bangjak, Phrakhanong Bangkok 10260. Tel: + 66 2 7425366 Fax: + 66 2 7425379
NORWAY
G. Heier A/S, Postal Address: Postboks 6615, Rodelokka, 0502 Oslo, Norway. Office Address: Thv, Meyersgt. 7, Oslo. Tel: + 47 232 34230 Fax: + 47 232 34242
TRINIDAD
Tracmac Engineering Ltd, P.O. Box 945, Port of Spain, Trinidad, West Indies. Tel: + 1 665 460 1532 Fax: + 1 868 671 0012
PAKISTAN
Brady & Co. of Pakistan Ltd, Shernaz House, P.O. Box 4453, West Wharf Road, Karachi 2. Tel: + 92 21.2310367/201712 Fax: + 92 21.2313376/2313378
TURKEY
Glengo Ithalat lhracat Mumessillik AS, Gungoren Cad. No. 35 Bagcilar, 34560 Bakirkoy, Istanbul. Tel: + 90 212 4613970 Fax: + 90 212 4613972 www.glengo.com.tr
PERU
Corporacion Basco S.A.C. Av. Argentina 1165, Lima 1, RUC 25776186. Tel: + 51 1 4336633 Fax: + 51 1 4313188
USA
Renold Power Transmission Corporation 8305 Global Way, Hebron, KY 41048 Tel: (800) 850-8141 Web: www.renoldusa.com E-mail: information@renoldusa.com Renold Inc Bourne Street, PO Box A, Westfield, New York, 14787-0546 Tel: + 1 716 326 3121 Fax: + 1 716 326 6121 E-mail: renold@cecomet.net
PORTUGAL
Harker, Sumner & Cia Lda, 38 Rue De Cueta 48, P.O. Box 75, 4001-Oporto Codex. Tel: + 351 2 29478090 Fax: + 351 2 29478098
UNITED KINGDOM
Renold Engineering Products Station Road, Milnrow, Rochdale OL16 3LS Tel: + 44 (0) 1706 751010 Fax: + 44 (0) 1706 751011 Web: www.renold.com Renold Gears Holroyd Gears Works, Milnrow, Rochdale OL16 3LS Tel: +44 (0) 1706 751000 Fax: +44 (0) 1706 751001 E-mail: sales@gears.renold.com Web: www.renold.com
SPAIN
Brown Pestell, Ctra N-11 Lm. 599.5 Nave 5, 08780 Palleja, Barcelona. Tel: + 34 93 6630740 Fax: + 34 93 6632057
SINGAPORE
Renold Transmission Limited 63 Hillview Avenue, #07-13, Lam Soon Industrial Building, Singapore 669569. Tel: + 65 6760 2422 Fax: + 65 6760 1507 E-mail: renold@mbox5.singnet.com.sg
VENEZUELA
Equipos Y Acessorios Astral CA, Apartado 1651 Valencia. Tel: + 584 1 332042 Fax: + 584 1 345641
SWEDEN
Renold A/S Skelmarksvej 6, Postboks 90 2605 Brndby Denmark. Tel: + 45 43 452611 Fax: + 45 43 456592 E-mail: renold@post9.tele.dk
WEB
www.renold.com
95
SALES COMPANIES
AUSTRALIA
Melbourne (Victoria) Tel + 61 (03) 9262 3333 Fax + 61 (03) 9561 8561 also at: Sydney, Brisbane, Adelaide, Perth, Newcastle, Wollongong, Townsville.
AUSTRIA
Vienna Tel + 43 (0) 13303484 Fax + 43 (0) 13303484-5 also at: Kiskrs (Hungary), Jaroslavice (Czech Republic).
BELGIUM
Brussels Tel + 32 (0) 2 201 1262 Fax + 32 (0) 2 203 2210
CANADA
Brantford (Ontario) Tel + 1 519 756 6118 Fax + 1 519 756 1767 also at: Montreal.
CHINA
Beijing Tel +86 10 65817522 Fax + 86 10 65810336
DENMARK
Brndby (Copenhagen) Tel + 45 43 452611 Fax + 45 43 456592
FRANCE
Seclin Tel + 33 (0) 320 16 29 29 Fax + 33 (0) 320 16 29 00 Calais (Chain only) Tel + 33 (0) 321 97 99 45 Fax + 33 (0) 321 97 83 45
GERMANY
Einbeck Tel + 49 (0) 5562 81 163 Fax +49 (0) 5562 81 164 also at: Hamburg, Bielefeld, Dsseldorf, Frankfurt, Kornwestheim, Berlin.
KOREA
Seoul Tel + 822 783 6829 Fax +822 784 9322
MALAYSIA
Petaling Jaya Tel + 603 5191 9880 Fax + 603 5191 9881 also at: Johor Bharu, Ipoh, Butterworth.
NETHERLANDS
Amsterdam Tel + 31 206 146661 Fax + 31 206 146391
NEW ZEALAND
Auckland Tel + 64 9 828 5018 Fax + 64 9 828 5019 also at: Christchurch.
SINGAPORE
Singapore Tel + 65 6760 2422 Fax + 65 6760 1507
SOUTH AFRICA
Benoni Tel + 27 11 845 1535 Fax + 27 11 845 3645 also at: Durban, Cape Town, Port Elizabeth, Witbank.
SWEDEN
Brndby (Copenhagen) Tel + 45 43 452611 Fax + 45 43 456592
SWITZERLAND
Dbendorf (Zrich) Tel + 41 1 821 45 85 Fax + 41 1 821 46 03 also at: Crissier (Lausanne).
UK
Renold Clutches & Couplings, Wales Tel + 44 (0) 29 20792737 Fax + 44 (0) 29 20793004 (Sales): +44 (0) 29 20791360 e-mail: couplings@cc.renold.com Renold Gears, Rochdale Tel + 44 (0) 1706 751000 Fax + 44 (0) 1706 751001 e-mail: sales@gears.renold.com Renold Hi-Tec Couplings, Halifax Tel + 44 (0) 1422 255000 Fax + 44 (0) 1422 320273 e-mail: couplings@hitec.renold.com
USA
Hebron, Kentucky Tel (800) 850-8141
WEB
www.renold.com
E-MAIL
e-mail : enquiry@renold.com
For other country distributors please contact Renold UK or visit the Renold website.
Whilst all reasonable care in compiling the information contained in this brochure is taken, no responsibility is accepted for printing errors. All information contained in this brochure is subject to change after the date of publication.