Professional Documents
Culture Documents
Anchor Bay
Anchor Bay
Anchor Bay
Contents
Tying wires Concrete spacers Plastic spacers Wire spacers Fabric reinforcement Bolt boxes, holding down bolts and grouts Slab accessories Polythene damp proof membranes Resin anchor system Joint llerboards Crack inducers and void formers Surface treatment chemicals Fosroc waterproong membranes Waterstops Fosroc range Fosroc joint sealants Grace waterproong membranes Waterstop Grace servicised range Cetco waterproong system Fosroc concrete repair Concrete repair Formwork tie rod system Formwork accessories Formwork chemicals Monotub formwork systems Formwork systems Kwikastrip continuity system Halfen HDB punching shear reinforcement Formrib and rebar couplers Concrete nishing tools Concrete test equipment Protection products Halfen-brick tie products Expamet brick tie products Tools Setting out products Cut and bent reinforcements Terms and conditions 4 5 6 8 9 10 12 14 15 16 18 19 21 22 24 26 28 29 30 31 32 34 36 38 39 40 41 42 43 44 45 46 48 50 52 53 54
Tying wires
A soft black annealed 16 gauge wire used for the tying of reinforcement.
Code TW16
Pack Coil
18 gauge stainless steel tying wire used for the tying of reinforcement.
Code SS18
Pack Kilo
An alternative way of tying reinforcement. The tie is folded around the rebar and tightened by the action of the tying tool.
The most popular tool used by all steel xers for the tying of reinforcement.
Code Nips
Pack Each
Concrete spacers
A concrete spacer designed to offer a single cover to reinforcement ideally used in horizontal applications.
Used for supporting reinforcement in both vertical and horizontal applications. Each block provides two separate covers.
A concrete spacer used in vertical and horizontal applications which offers three separate covers.
A heavy duty bar spacer used for supporting large reinforcement in heavy duty slabs.
Plastic spacers
Track spacer
A continuous plastic spacer for supporting bottom reinforcement in suspended slabs. Also used on metal because of its stability and excellent concrete ow characteristics.
Wheel spacers
A robust clip-on plastic spacer wheel. Ideal for the use on columns, walls and beams. Offers minimum contact with formwork.
Code 20SW12 25SW12 25SW20 30SW12 30SW20 35SW12 35SW20 40SW12 40SW20 50SW12 50SW20
Cover 20mm 25mm 25mm 30mm 30mm 35mm 35mm 40mm 40mm 50mm 50mm
Bar dia. 4 to 12 4 to 12 8 to 20 4 to 12 8 to 20 8 to 12 10 to 20 4 to 12 8 to 20 4 to 12 8 to 20
Pack 1000 500 500 500 500 250 250 250 250 250 250
Meshfix spacers
A heavy duty double cover plastic spacer designed to support mesh and rebar off polystyrene insulation and polythene. Membranes in ground slabs.
Plastic spacers
cont.
A heavy duty single cover spacer clip-on chair spacer designed for all pre-cast and site applications.
Bar dia. 8 to 20 8 to 20 8 to 20 8 to 20 8 to 20 8 to 20
A heavy duty clip-on plastic wheel spacer designed for in-situ piling and diaphragm wall applications.
Bar dia. 6 to 20 6 to 20
Levelling shims
A hard plastic shim used for packing during the alignment of precast panels. Supplied in plain or horseshoe styles.
Code (Horseshoe) LS02 LS03 LS05 LS07 LS09 LS10 LS20 (Plain) LS02P
Size 2mm 3mm 5mm 7mm 9mm 10mm 20mm 2mm 3mm 5mm 7mm 9mm 10mm 20mm
Pack 250 250 125 125 125 250 150 250 250 125 125 125 250 150
Horseshoe
Plain
Wire spacers
Deckchairs
A welded girder used for supporting fabric and reinforcement without damaging the polythene membrane. They can also be used to support dowel bars. Supplied in 2 metre lengths.
Code DK50 DK60 DK75 DK90 DK105 DK120 DK135 DK150 DK165 DK180 DK200 DK220 DK230 DK250 DK270 DK280 DK300
Cover 50mm 60mm 75mm 90mm 105mm 120mm 135mm 150mm 165mm 180mm 200mm 220mm 230mm 250mm 270mm 280mm 300mm
Pack 50m 50m 50m 50m 50m 50m 50m 50m 50m 50m 50m 50m 50m 50m 50m 50m 50m
Hoop spacers
A fast and economical way to support mesh reinforcement in slabs. The hoops are formed into a 1 metre diameter circle and three or four hoops per sheet of mesh is generally sufcient.
Code CS50 CS60 CS75 CS90 CS105 CS120 CS135 CS150 CS165 CS180 CS200
Cover 50mm 60mm 75mm 90mm 105mm 120mm 135mm 150mm 165mm 180mm 200mm
Pack 25 25 25 25 25 25 25 25 25 25 25
Fabric reinforcement
Standard fabric
Manufactured to BS 4483 from cold reduced wire which complies with BS 4482. Each wire intersection is resistance welded using electronically controlled techniques. Standard sheet size: 4.8m x 2.4m Merchant sheet size: 3.6m x 2.0m
Standard sizes (4,800 x 2,400) BS ref. Mesh size nominal pitch of wires Main Cross (mm) (mm) 200 200 200 200 200 100 100 100 100 100 100 100 100 100 100 100 200 100 200 200 200 200 200 200 200 200 200 200 200 400 400 400 400 400 200 100 Wire sizes Main (mm) 10 8 7 6 5 12 10 8 7 6 5 10 9 8 7 5 5 2.5 Cross (mm) 10 8 7 6 5 8 8 8 7 7 7 6 6 5 5 5 5 2.5 Cross sectional area per meter width Main Cross (mm) (mm) 393 252 193 142 98 1131 785 503 385 283 196 785 636 503 385 283 98.0 49.1 393 252 193 142 98 252 252 252 193 193 193 70.8 70.8 49.0 49.0 49.0 98.0 49.1 Nominal weight per m2 (kg) 6.16 3.95 3.02 2.22 1.54 10.90 8.14 5.93 4.53 3.73 3.05 6.72 5.55 4.34 3.41 2.61 1.54 0.77 Sheets per tonne (approx) 15 22 29 40 57 8 11 15 20 24 29 13 16 20 26 34 57 113 Sheet weight (kg) Sheets per bundle Sq. metres per tonne
A393 A252 A193 A142 A98 B1131 B785 B503 B385 B283 B196 C785 C636 C503 C385 C283 D98 D49
70.96 45.50 34.79 25.57 17.74 125.57 93.57 68.31 52.19 42.97 35.14 77.41 63.94 50.00 39.28 30.07 17.74 8.87
18 28 34 46 60 10 14 18 24 30 36 16 20 26 30 32 60 50
162.34 253.16 331.13 450.45 649.35 91.74 122.85 168.63 220.75 268.10 327.87 148.81 180.18 230.41 293.26 383.14 649.35 1298.70
Merchant size (3,600 x 2,000) BS ref. Mesh size nominal pitch of wires Main Cross (mm) (mm) 200 200 200 200 200 200 200 200 Wire sizes Main (mm) 10 8 7 6 Cross (mm) 10 8 7 6 Cross sectional area per meter width Main Cross (mm) (mm) 393 252 193 142 393 252 193 142 Nominal weight per m2 (kg) 6.16 3.95 3.02 2.22 Sheets per tonne (approx) 23 35 46 63 Sheet weight (kg) Sheets per bundle Sq. metres per tonne
26 30 50 50
Made from waxed cardboard, they provide an easy method of bolt alignment for steel frame buildings.
An economical way of providing a void around holding down bolts for steel frame buildings.
Code PC0 PC1 PC2 PC3 PC4 PC5 PC6 Code DIS05 DIS25
Depth 150mm 225mm 300mm 375mm 450mm 525mm 610mm Description Disolver 5ltr Disolver 25ltr
Made from expanded metal for the positioning of holding down bolts where the bolt box is to remain in the concrete.
Depth/Diameter 150mm x 75mm 225mm x 75mm 300mm x 75mm 375mm x 100mm 450mm x 100mm 600mm x 100mm
A range of high tensile grade 8.8 holding down bolts complete with nuts and washer plates 100 x 100 x 10mm
Size M20 x 300mm M20 x 375mm M20 x 450mm M24 x 375mm M24 x 450mm
10
cont.
A high strength non shrink cementitious grout when added to water provides excellent free ow properties for grouting in holding down bolts. Coverage: 13 litres/25kg approx.
Cebex 100
Is an admixture for site batched cementitious grouts where a reduced water/cement ratio and positive expansion is required. Yield: 50kg of opc + 20-22 ltrs water + 225g cebex 100 = 36 litres 50Kg op opc + 22-24 ltrs water + 225g cebex 100 = 57 litres
Code COM100
Size 24 x 225g
Denso tape
Used to protect bolt heads prior to pouring concrete. Roll size: 75mm x 10m
Code DEN75
11
Slab accessories
Dowel bars
Plain round mild steel dowel bars used in contraction and expansion joints in slabs. Other sizes available on request.
Size 12mm x 900mm 12mm x 1000mm 16mm x 400mm 16mm x 600mm 16mm x 900mm 20mm x 500mm 20mm x 600mm 25mm x 600mm
A exible pvc sleeve which provides a very efcient method of debonding mild steel dowel bars. Meets with all D.O.T. specications.
Size
Pack
12mm x 450mm 100 16mm x 450mm 100 20mm x 300mm 100 20mm x 450mm 100 25mm x 300mm 100 32mm x 375mm 100
A foam plug supplied separately for insertion into dowel bar sleeves to allow for expansion.
A rigid pvc tube with a compressible ller one end which is designed to allow for expansion of dowel bars in construction joints.
12
Slab accessories
cont.
Debonding compound
A bitumen based compound used for bond breaking of dowel bars in concrete. Complies to Clause 2605 of D.O.E. specication for roads and bridge works.
An accurate method used to support dowel bars in contraction and expansion joints in oor slabs and road construction.
An easily adjustable plastic screed chair which is designed to be left in the concrete part or whole. Suitable for use with scaffold tubes or Anchor Bay screeding rail. For slabs 150mm-350mm.
A sturdy two component metal screed chair for screeding slabs up to 400mm.
Slab thickness 120mm - 150mm 150mm - 200mm 200mm - 300mm 300mm - 400mm
A heavy duty re-usable and fully adjustable metal screed chair for slabs up to 500mm. For long life wash and oil after use.
Code HDSC
Pack Each
Used in conjunction with screed chairs. Size: 50mm x 25mm x 3mm Length: 7.5 metre
Code S/RAIL
Pack 7.5m
13
Polythene DPM
Code HDPS
Gauge 65
Jointing tapes
A 75mm wide tape designed for the sealing of laps on polythene DPMs. A double sided tape used in the sealing of laps on polythene DPMs.
Pack 16 10
Geotextile
A cost effective solution to the problem of constructing stable granular layers over soft foundation soils.
Code GEOTEX
Terram
Terram nonwoven geotextile provides an effective solution to the age old problem of constructing stable granular layers over soft foundation soils.
Code TERRAM/1
14
Fosroc Lokfix
The two versions of lokx are premeasured, two-part, lled polyester resin grouts. After hardening, the grout produces anchorages of consistent reproducible values. Lokx S25 pour grade is for use where the hole is 8 to 40mm greater in diameter than the bar. Lokx P25 pump grade is used in overhead or horizontal holes where the hole is up to 25mm greater in diameter than the bar.
A thixotropic low-slump polyester resin grout for anchoring bolts, dowel bars, starter bars, into vertical and sloping plane concrete, rock and masonry. Size: 380ml
Application equipment
Calculation table
Hole diameter 20mm 25mm 32mm 38mm 45mm 51mm 57mm 64mm 76mm
A guide table to calculate the volume of resin grout required per hole. Bolt diameter 25mm
20mm
32mm
38mm
44.5mm
51mm
0.031 litre 0.064 litre 0.110 litre 0.155 litre 0.206 litre 0.273 litre 0.079 litre 0.124 litre 0.175 litre 0.241 litre 0.046 litre 0.091 litre 0.142 litre 0.208 litre 0.100 litre 0.166 litre 0.298 litre 0.117 litre 0.249 litre
15
Joint llerboards
Is a compressible joint llerboard manufactured from bitumen impregnated wood bres. It is supplied in sheet form and is used to form and ll expansion joints in in-situ and pre-cast concrete construction. Complies to DTP specication for Highway Works Dec 1991 Series 1000 Clause 1015 (Pavement Joints). Sheet size 1.220m x 2.440m
Code 12FBS 20FBS 25FBS Width 100mm 125mm 150mm 175mm 200mm 225mm 250mm 12mm 12FB100 12FB125 12FB150 12FB175 12FB200 12FB225 12FB250 20mm
20FB100 25FB100 20FB125 25FB125 20FB150 25FB150 20FB175 25FB175 20FB200 25FB200 20FB225 25FB225 20FB250 25FB250
Korkpak fillerboards
Preformed bitumen bonded cork joint llerboard for critical water retaining, civil and structural expansion joints. Sheet size 2.0m x 1.0m. Cut strips available on request.
16
Joint llerboards
cont.
Foam fillerboard
Is a closed cell polyethylene joint ller for use as expansion joint ller in brick and blockwork, isolation joints and hinge joints where a readily compressible low load transfer joint ller is required. Density 35kg/m3. Supplied in sheets and cut strips with tear off. Sheet size: 2.0m x 1.6m
Code 10EXPS 12EXPS 15EXPS 20EXPS 25EXPS 30EXPS Width 100mm 125mm 150mm 175mm 200mm 225mm 250mm Width 100mm 125mm 150mm 175mm 200mm 225mm 250mm 10mm 12mm
10EXP100 12EXP100 15EXP100 10EXP125 12EXP125 15EXP125 10EXP150 12EXP150 15EXP150 10EXP175 12EXP175 15EXP175 10EXP200 12EXP200 15EXP200 10EXP225 12EXP225 15EXP225 10EXP250 12EXP250 15EXP250 20mm 25mm
20EXP100 25EXP100 20EXP125 25EXP125 20EXP150 25EXP150 20EXP175 25EXP175 20EXP200 25EXP200 20EXP225 25EXP225 20EXP250 25EXP250
A crossed linked, non absorbent, semi-rigid, cellular polyethylene joint used for forming expansion joints in concrete, brickwork and blockwork. The product provides excellent support to sealants subject to hydrostatic pressure and is particularly recommended for water retaining or water excluding structures. Density: 60 kg/m3. Sheet size: 1.8m x 0.9m. Cut strips available on request.
Adhesives
A contact adhesive designed for the xing of llerboards to a wide range of surfaces.
17
Made from extruded PVC and used to induce controlled cracking in concrete slabs. Can be left in place omitting the use of a joint sealant.
Pack 5m 5m
Used in the same application as one part crack inducer but where the top section can be removed after concrete has cured to leave a void for sealant 10mm x 25mm.
Pack 5m 5m
Used to induce a controlled crack from the underside of slabs. Can be used in conjunction with either top crack inducers or saw cutting.
Pack 5m 5m
Aluminium T-bar
A rigid reusable aluminium T-section used to form a straight void in wet concrete to accept top crack inducers.
Pack 5m 5m
Void formers
A reusable rigid PVC void former used in conjunction with bre boards to create a grove in wet concrete prior to sealing with joint sealant.
Pack 3m 3m 3m 3m
18
A spray applied acqueous solution of blended silicates designed to prevent early drying out which enables the cement to hydrate more efciently, considerably reducing the risk of surface crazing and shrinkage whilst also giving a stronger, more durable surface. Coverage: 5.5-6m2/litre
A spray applied resin curing membrane used to protect freshly placed or formwork cast concrete from excessive water loss during the critical curing period and should be applied as quickly as possible to ensure maximum benet. Coverage: 5m2/litre
A resin based curing membrane which contains aluminium akes which when sprayed on the concrete surface produces a metallic mirror surface to reect away solar heat, this is particularly advantageous on large expanses of concrete such as airport runways and concrete roadways. Coverage: 5.5 m2/litre
A 90% efciently resin based curing agent which prevents premature drying out of the concrete surface thus reducing the risk of surface cracking.
19
cont.
Dustproof hardener
A solution used as a treatment on new old concrete to give a superior surface resistance to abrasion and cracking attack with the added bonus of dust reduction. Coverage: 6 m2/litre approx.
Bitumen emulsion
A cold applied rubberised bitumen emulsion used as a protective damp proof membrane to concrete and brickwork. For best results two coats is recommended. Coverage: 1.1-1.7m2/ litre per coat.
RIW L.A.C
A spirit based bitumen emulsion used as a water and water-vapour proof membrane for foundation walls, oor slabs etc. Coverage: 1m /litre (2 coats).
2
RIW Flexiseal
A solvent free thixotropic liquid based on urethane pre-polymers which on contact with atmospheric moisture, cures to give a continuous tough rubber like coating. The material is supplied in the form of a blue base coat and a black top coat. Coverage: Base and top 1m /kg
2
Description Blue base 5ltr Blue base 25ltr Black top 5ltr Black top 25ltr Primer 5ltr Primer 25ltr
RIW Toughseal
A polymer modied epoxide coating supplied as a two part pack of base and hardener which cures to form a tough black water and waterproof coating. Coverage: 4m2/litre per coat.
20
Proofex 3000
A high performance self adhesive membrane for a range of waterproong applications including basements and substructures. Proofex 3000 provides a vapour and waterproong membrane to water excluding structures and protects concrete from attack by aggressive ground salts. Roll size: 1m x 20m
Proofex engage
Is a unique patented system comprising a complex cell mesh bonded to a polyethylene membrane which allows poured concrete to interlock with the membrane forming a tenacious mechanical bond. Proofex engage is supplied with a selvedge on one side to provide sealed laps. Roll size: 1.27m x 30m
Code PROF/ENG
A reinforced, double sided waterproong adhesive tape for sealing and jointing roll ends, cut edges corner pieces, sold in packs of two. It consists of a strong synthetic bre fabric impregnated and coated both sides with a bitumen rubber adhesive. Each side of the tape is protected by a removable siliconised paper. Roll size: 200mm x 10m
Code PROF/STRIP
Proofex lm
Is a two component applied liquid membrane for sealing around intricate details such as pipe entries penetrations, pile caps, etc. Coverage: approximately 4-6kg/m at normal loadings,
2
21
When used on ground slabs where the waterstop is supported on blinding, Rearguard proles usually require no xing. The waterstop is layed centrally over the line of the joint to be formed. Fixing to vertical shuttering is done by nailing through the outer nailing anges leaving the head of the nail proud so that it is held in the cured concrete. This prevents the waterstop being displaced when the shuttering is struck. Roll size: 12 metre
Code REAR/250
Size 12m
Code A range of junctions for use with supercast rearguard S250. Centre bulb selections are used in expansion, contraction joints. R250/FM R250/F3W R250/F4W R250/INT90 R250/EXT90
The centre bulb allows for movements in a structure to be accommodated whilst its hexagonal design provides a at surface. This allows shuttering and joint llers to t snugly. All centrally placed supercast waterstops incorporate an eyeletted, reinforced edge ange. This enables them to be easily positioned by wiring to surrounding reinforcement. Roll size: 12 metre
Code HYDRO/250
Size 12m
22
cont.
Supercast SW10
Integral sealing for construction joints in concrete cast in-situ. Convenient and problem solving in-situations where a conventional waterstop would require complex shuttering. Typical uses include secant piled and diaphragm walled basements, pile caps and casting against old concrete. Roll size: 15 metre
Code SCAST/SW10
23
Thioex one is a one part, gun applied moisture activated, polysulphide sealant. It is ideal for sealing joints in window and door frame surrounds and as a capping forbeaded glazing systems. Conforms to BS 5215: 1986. Cartridge size: 380mls Colours: black, buff, mahogany, grey, stone, cement white, white, brick red.
Code THIO/1
Pack 380mls
Thioex 600 is available in gun and pouring grades. The gun grade is ideal for general application, and is available in a range of colours. It is packed in a ready to mix 2.5 litre tin containing the base and curing agent in the correct proportions. The pour grade for joints in horizontal surfaces is supplied in grey only in 5 litre packs with the base and curing agent in separate tins. Conforms to BS 4254: 983, BS 6920:1996
Polysulphide primer
Fosroc primer 7 is a one part chemically active clear liquid for brush application to concrete, stone, brickwork, timber and unglazed edges of ceramic tiles prior to applying thioex sealants.
Code THIO/PR
Pack 500ml
/each 12.28
Fosroc colpor 200PF is a high performance, pitch free, pavement joint sealant. Used for the sealing and maintenance of joints in concrete roads, concrete runways and hardstandings. Colpor 200 PF is particularly suitable for sealing areas where fuel and oil spillage might occur such as aircraft fuelling areas, oil terminals, garage forecourts, parking and cargo areas. Conforms to BS 5212: 1990-types n, f and f b. Colour: black
Code COLPOR200
Pack 5 litre
24
cont.
Fosroc pliastic is a hot-poured rubber bitumen horizontal joint sealant. Used for sealing movement and construction joints in pavements, oor slabs, water retaining and water excluding structures. Colour: black Conforms to BS 2499: 1993 pliastic N2 Yield: 19.6 Litre per pack
Code HPS20
Pack 20kg
A closed cell polyethylene foam cord used as a packing material for joint sealants.
Code BR6 BR10 BR12 BR15 BR20 BR25 BR30 BR40 BR50
Size 6mm 10mm 12mm 15mm 20mm 25mm 30mm 40mm 50mm
Pack 1500m 1100m 900m 500m 300m 200m 150m 80m 50m
Accessories
Tools and accessories used in the application of joint sealing materials. Mixing paddle: used for mixing sealants Barrel gun: used for the placement of bulk ll sealants. Supplied with three different size nozzles. Follower plate: designed to assist the lling of barrel guns. Cleaning solvent: a solvent based liquid used for cleaning tools and barrel guns. Gloves: a pvc knitted wrist glove Bond breaking tape: used as a bond breaker between joint sealant and breboard. 25mm x 50m roll.
25
Bituthene 3000
A self-adhesive, rubberized asphalt/ polyethylene waterproong membrane. Ideal for waterproong concrete decks. Roll size: 0.9m x 20m
Bituthene 4000
A self-adhesive hdpe waterproong membrane. Its cross laminated, high density polyethylene carrier lm provides high tear strength and puncture and impact resistance. Roll size: 0.9m x 20m
Bituthene 8000
Bituthene 8000 combines the proven bituthene adhesive technology with a unique, grey coloured carrier lm to provide superior performance and easier installation. It can be used horizontally or vertically to protect basements and other critical sub structures from the effects of water, damp and gas. Roll size: 1m x 20m
A two component, elastomeric, liquid applied detailing compound for use with grace waterproong membranes. Size: 5.7ltr
Code BITU/LM
Description Bituthene lm
26
cont.
Code Durable, lightweight boards for permanent protection of waterproong membranes from abrasive backll, site trafcking and reinforcement xing. Supplied in 3mm and 6mm thick sheets. Sheet size: 2m x 1m S/PAK03 S/PAK06
Is a pre-applied waterproong membrane that bond integrally to poured concrete for use below slabs or behind basement walls on conned sites. Preprufe 300R is a heavy duty grade for use below slabs and on rafts. Designed to accept the placing of heavy reinforcement using conventional concrete spacers. Preprufe 160R is a thinner grade for lighter applications and blindside, zero property line applications against soil retention systems. Roll size: Preprufe 300R 1.2m x 30m Preprufe 160R 1.2m x 35m
Preprufe tape
Used for covering cut edges, roll ends, penetrations and detailing. Roll size: 100mm x 15m
Code PRE/TAPE
27
Serviseal
An external PVC waterstop system for passive protection of expansion, construction and contraction joints in reinforced concrete structures.
Servitite
A high performance, internal PVC waterstop for passive protection of critical joints in reinforced concrete structures.
AT system
A high performance PVC waterstop system with co-extruded hydrophilic bulbs to provide a unique combination of active and passive protection for joints in concrete.
Servistrip AH 205
A solid, active jointing strip which swells when exposed to water to prevent leak paths in concrete. Roll size: 20mm x 5mm x 10m
Code AH205
28
Volclay voltex
Voltex is a highly effective waterproong composite of high strength geotextile and 4.88kg of sodium bentonite per square metre. A patented needle-punch process interlocks the geotextiles together forming an extremely strong composite that maintains the equal coverage of bentonite, as well as protects it from inclement weather and construction related damage. Once backlled, voltex hydrates and forms a monolithic waterproong membrane. Voltex contains zero voc, can be installed in almost any weather condition to green concrete. Roll size: 5.0m x 1.1m
Code VOLTEX
Voltex accessories
Code Voltex nails and soft washers allows direct shot-red applications to secant and contiguous piling, steel sheet piling, diaphgregm wall, skin wall cast in-situ and under blinding. Pack size: 150 Stapler & staples used to secure laps on sand or concrete underlining, or to complement shot-red xings. Pack size: 2500 Code VOL/STPLR VOL/STAP VOL/NAIL
Volclay granules
Code Volclay granules are used to ll cavities and voids in the substrate prior to installing the main bentonite waterproong course. It is also used to seal around slab penetrations to form a continuous waterproong system. Pack size: 20kg VOL/GRAN
Code Waterstop RX101 is a sodium bentonite based waterstop designed to stop water inltration through cast-in place concrete construction joints by expanding upon contact with water to form a positive seal against the concrete. Roll size: 5 metre Telephone 0870 24 24 234 Fax 0870 24 03 613 RX101 REVOFIX RXWB
29
Renderoc GP
Is a general purpose concrete reinstatement mortar which can be used as a render as well as for all types of patch repairs. Renderoc GP is alkaline in nature and will protect embedded steel reinforcement. Renderoc GP is designed for vertical, overhead or horizontal applications. It can be applied up to 20mm thickness in sections overhead and 30mm thickness in vertical sections. Coverage: 16 litres/25kg bag 1.6m2 at 10mm thickness
Code REN/GP
Size 25kg
Renderoc FC
Is designed for application in thin layers to produce a fair-faced appearance to concrete surfaces in readiness to receive a protective/decorative coating. Renderoc FC is designed for vertical and overhead use to inll honeycombing and voids up to 3mm deep in the surface of concrete. Coverage: 15 litres/25kg bag 5.0m2 at 3mm thickness
Code REN/FC
Size 25kg
Renderoc HB
For the reinstatement of large areas of concrete and for small, localised patch repairs. Renderoc HB is alkaline in nature and will protect embedded steel reinforcement it is specically designed for vertical and overhead high-build applications. Renderoc HB can be applied in sections up to 80mm thickness in vertical locations and up to 50mm thickness in overhead locations in a single application and without the use of formwork. Coverage: 14.5-15.0 litres/18kg 15m2 at 10mm thickness
Code REN/HB
Size 18kg
30
Concrete repair
Fastpatch cement
A prepacked specialised repair cement, based on the latest polymer cement technology, it provides a simple, cost effective rapid repair system for in-situ and precast concrete, masonry, screeds, renders, brickwork and blockwork. Colours: grey and white. Coverage: 1kg yields 500cm3 or 2.1kg/mm/m2
Fill n rub
A convenient method of lling blow holes and small surface defects in precast or in-situ cast concretes, as well as providing an even standardised colour and aesthetic nish.
Code FIL/RUB25
Size 25kg
Is a styrene butadiene emulsion for use as an admixture in cementitious compounds. It will improve many of the properties of the compound such as improving strength, excellent adhesion, wear resistance, waterproof and weather resistance and shrinkage. Full technical details available on request.
A versatile and non-toxic ready to use PVA bonding and sealing adhesive giving a strong but exible bond with high moisture and mould resistance. Typical uses: priming, woodworking, concreting, oor laying, plastering and rendering, tiling, painting and decorating.
Ancillary products
Description Mixing paddle Carborundum stone Plastic oat Wooden oat Metal oat Site pvc bucket PVC knit wrist gloves Turks head brush
31
A self cleaning high tensile steel tie rod designed for use with formwork. Available in 15mm and 20mm diameters.
Wing nuts
Waler plates
A high quality pressed plate used in conjunction with tie rods and wing nuts to secure formwork. Dimensions: 100 x 100 x 10mm to suit 15mm tie rod 120 x 120 x 20mm to suit 20mm tie rod.
A jointing nut used to connect two tie rods together with a centre stop to ensure equal spacing inside the connector. Length: 105mm
Code JN15
Size 15mm
Used in water retaining structures. Cast into the concrete wall between two separate tie rods. After pouring tier rods are removed and water barrier remains in-situ.
Rock anchor
Used for securing single sided formwork in concrete or rock walls. (37Mm drill bit)
Code RA15
Size 15mm
32
cont.
Cast in anchor
A plastic cast in anchor which is secured to formwork and cast into initial pour to provide an anchor for tie rod in subsequent pours.
Code C/ANCHOR
Size 15mm
Weldable anchor
An anchor which can be welded to structural steel beams ,sheet piling and other metal structures to accept 15mm tie rod. Anchors must be welded continuously all the way round load tests should be conducted before use.
Code WELD/ANCHOR
Size 15mm
A rigid pvc tube used as a spacer between formwork and also allows tie rod to be removed easily.
A pvc cone used on both ends of tie rod sleeves which can be easily removed after formwork is struck.
Flupps
Used in conjunction with tie plug cement to give a water tight seal in areas where tie rods have been removed.
A cement specially developed for plugging and waterproong of tie holes in concrete walls.
Code TP8
Pack 8kg
Wedge anchors
Code WEDGE
Pack 25
33
Formwork accessories
An extruded rigid pvc section which can be nailed to formwork or column shutters to form chamfered corners. Supplied with or without nailing ange.
Code CF11 CFN11 CF15 CFN15 CF20 CFN20 CF25 CFN25 CF30 CFN30
Size 11mm 11mm 15mm 15mm 20mm 20mm 25mm 25mm 30mm 30mm
Pack 100m 100m 100m 100m 100m 100m 100m 50m 50m 50m
A wooden section which can be nailed to formwork or column shutters to form chamfered corners.
Formwork magnets
A magnet used for removing wire and nails from shutters prior to concreting.
Code MAGNET
Pack 2
Formwork tape
A pvc tape used for the sealing of joints in formwork to prevent grout loss. Roll size 50mm x 33m
Code FTR50
Pack 30 rolls
Designed for use on all types of formwork. Grout check foam is a closed cell polyethylene foam with a high pressure adhesive on one side used for sealing joints in formwork to prevent grout loss. Available in two sizes: 6mm x 12mm x 10m. 12mm x 24mm x 5m.
34
Formwork accessories
cont.
Silicone sealant
A clear high modulus silicone sealant in 310mls which can be used for lling movement joints in formwork.
Pack 25 1
Handy foam
An aerosol packed polyurethane foam which expands when released used for lling gaps in formwork and other construction areas.
Code FHP750
Pack 12
A re retardant aerosol packed polyurethane foam which prevents the transmission of smoke, seals around pipework, insulates against noise, heat or cold. Conforms to din 4102 part 1 class b1. CFC free.
Code FRF750
Pack 12
Formwork plugs
A plastic conical shaped plug used for the lling of redundant tie holes in timber shutters.
Plastic kickers
Plastic formwork kickers are used to secure formwork at the base of walls. They are supplied with a masonry nail which can be placed with the aid of a hilti gun. Telephone 0870 24 24 234
Code P/KICKER
Pack 100
35
Formwork chemicals
Mould oil
A general purpose mould oil with good release qualities. For use on all types of formwork. Can be brush or sprayed applied.
Size 205 25
A general purpose chemical release agent which provides excellent release and surface finish. Reduces blowholes, staining and surface blemishes.
Size 205 25
Surface retarder
Mould applied (code SRG25) brushed onto formwork, it is designed to give an exposed aggregate surface which gives an excellent key for subsequent concreting. Surface applied (code SRS25) sprayed onto fresh concrete to give an exposed aggregate finish.
Size 25 25 205
Formwax sealer
Formwax is specifically developed for the initial sealing of various formwork surfaces. Based on crystalline waxes and with a fugitive dye which will not stain permanently, this thixotropic material when worked into a surface takes on a smooth, thin paste consistency. Its economy of use, speed of application and compatibility with most types of release agent make it the ideal preservation sealer. Coverage: 10m2/kg approx.
Code FW20
Size 20kg
36
Formwork chemicals
cont.
A quick setting two part polyester ller used for lling holes and damaged areas on wood, breglass or metal formwork. It is easily worked and sanded and is compatible with release agents.
Formwork plugs
A plastic conical shaped plug used for the lling of redundant tie holes in timber shutters.
Sprayers
High performance sprayer units for the application of mould oil and chemical release agent.
Code MS08/S PS08 KN20 NOZZ LANCE TRIGGER GASK/M GASK/P SOLV/5 SOLV/25
Description 8ltr metal sprayer 8ltr plastic sprayer 20ltr knapsack Nozzle Sprayer lance Sprayer trigger unit Metal gasket set Plastic gasket set Cleaning solvent 5ltr Cleaning solvent 25ltr
Barrel accessories
Taps and pumps used in conjunction with plastic and metal barrels.
37
Monotub
Is a disposable formwork for rapid construction of circular and square concrete columns. Advantages: Fast and economical to use 100% water resistant and can be stored outside without damaging the quality of the tube. Light and easy to handle. Quick and easy to erect Provides the optimum fair face nish concrete column. Requires no mould oils or release agents. Stripped literally in seconds. Very strong Can be used for horizontal void forming. Manufactured in a large range of sizes. Delivered at short notice. (Popular sizes typically 24/48 hours)
Code MONO150 MONO200 MONO240 MONO250 MONO300 MONO350 MONO400 MONO450 MONO500 MONO550 MONO600 MONO650 MONO700 MONO800 MONO900 MONO1000 MONO1200 Code MONO/200S MONO/250S MONO/300S MONO/350S MONO/400S
Diameter 150mm 200mm 240mm 250mm 300mm 350mm 400mm 450mm 500mm 550mm 600mm 650mm 700mm 800mm 900mm 1000mm 1200mm Dimension 200mm x 200mm 250mm x 250mm 300mm x 300mm 350mm x 350mm 400mm x 400mm
Monotub accessories
38
Formwork systems
Claymaster
Is a low density expanded polystyrene, designed to compress under load and so reduce the lateral forces of ground movement on the foundation. Sheet size: 2.4m x 1.2m. Thickness: 50mm-300mm
Cellcore
Consists of a honeycomb of interlocking sections made from expanded polystyrene. Designed so as ground movement occurs cellcore compresses and buckles to accommodate it, thereby reducing the forces that would otherwise be transmitted to the foundations. It is used extensively in both residential and commercial applications to protect piled beams and rafts, heavy slabs and reinforced ground oor slabs. Sheet size: 2.44m x 1.22m. Grades: CC & CP full technical information available on request.
Clayboard
Is a unique, environmentally friendly void former and foundation stabiliser made from a biodegradable honeycomb core set between lightweight polypropylene facings. When dry clayboard is strong enough to support the weight of wet concrete and steel reinforcement. Sheet size: 2.440m x 1.0m. Full technical information available on request.
Polystyrene sheets
A SDN grade expanded polystyrene board used to as thermal insulation and void former in walls and ground oor slabs. Can be cut accurately with the aid of a ne tooth saw to any shape or size. Sheet size: 2.44m x 1.2m (8 x 4). Other thickness available on request
39
The Kwikastrip reinforcement continuity system has been rmly established over many years as the contractors rst choice. This results from consistent delivery of an almost innitely variable product within a very short lead-time. To further reassure engineers, Kwikastrip is supported by the highest level of technical endorsement in the form of UK CARES Technical Approval.
40
Halfen HDB punching shear reinforcement is designed to prevent punching failure at column heads in concrete at slab construction without the traditional need for downstand beams, mushroomheaded columns and thickened oors. The system is manufactured from ribbed bars which are hot-forged to make double-ended studs (connected by spacer rails) to provide virtually slip-free shear head reinforcement with excellent anchorage. The two or threestud elements are simply dropped into place in the reinforcing cage and retained in position by means of clip bars and/or tying wire. This typically reduces site installation time from hours to minutes per column head compared to traditional bent reinforcement.
To facilitate selection and use, a specially-written software programme that calculates shear stress and reinforcement requirements is available. The HIT System is the latest development in thermal break and reinforcement continuity for cantilevered balcony construction. HIT helps to eliminate the effects of cold bridging (i.e. condensation and mould growth) experienced with reinforcement that is traditionally continuous from internal slab straight through to external balcony. The HIT System comprises special stainless steel swaged couplings in the tension zone (into which is factory-tted normal highyield reinforcement) and stainless steel double-headed studs in the compression zone. These stainless steel components are housed in a high-density polystyrene fabrication which provides the thermal separation between oor slab and balcony. The HIT System is supplied in versions for in-situ and precast applications and modules of 1.0m and 0.2 metres that can be used in combination to avoid cutting.
41
A galvanised expanded metal used widely in the construction industry as a permanent shuttering for stopends. It is manufactured from hot-dipped zinc coated steel sheet to BS EN 10142 1991. Sheet size: 3m x 0.445m
Code FORMRIB/3
Description 3m x 0.445m
MBT couplers
The MBT range of couplers provides a cost effective method of joining reinforcing bars particularly when the xed bar is already in place. They can be installed without any preparation to the bar ends and without any need to rotate bars.
Bar diameter External diameter d Total length l Socket size A/F (ins) No. of bolts Approx. weight (kg)
The HBM system consists of highstrength couplers factory-swaged onto grade 500 high-yield reinforcement bars. Anchorage reinforcement (female socket bars) can be supplied in shapes and lengths to suit almost any application conguration. The male connection bar has a hot-forged upset end onto which is rolled a standard metric thread. HBM is hallmarked by off-theshelf availability and CARES Technical Approval.
42
A zinc plated steel oat incorporating radius arms and a texturing broom for brush work. The broom is a polybristle medium texture. Floats have radius ends to prevent lap marks. Size: 1200mm (4ft).
Code E/FLOAT1200
An aluminium snap extension handle used in conjunction with easy oats. Size: 1800mm (6ft)
Code E/HANDLE
Concrete rake
The tools are lightweight and of rugged construction and are designed to allow the placement of concrete where required. The tooth side is for raking and the smooth side is for oating and screeding.
Code C/RAKE
Primarily used for concrete texturing on motorways, airport aprons and taxiways.
Hand floats
Tamping beam
An aluminium box section beam used for tamping and levelling concrete. Supplied either with or without handles. Length: 6000mm. Other lengths available on request.
Code T/HANDLE
Description Handles
Carborundum stone
A carborundum rubbing block used to smoothen out uneven concrete repaired surfaces.
Code C/STONE
43
Cube moulds
A high quality four part design cube mould with meets requirements of BS1881 part 108, EN12390-1 and ISO1920
Curing tank
A curing tank which can take up to 30 x 150mm cube moulds, made from polyethylene and measuring 990mm x 686mm x 635mm overall. Fitted with a 220 volt 3kw heater but also works on 110 volt (heating taking a little longer) tted with mechanical thermostat and a galvanised mesh lower rack. The thermostat is factory set to control the tank at 20C. It is ideal for site use where an economical solution is required. Meets standard BS 1881 part 111 EN 12390-2.
Code C/TANK
Slump cone
Designed to measure the workability of concrete. This is carried out by ling the slump cone with fresh concrete in three layers, tamping each one and levelling to the top of the cone. The slump cone is then removed and the distance the concrete falls or slump is measured with the rule.
Scoop
An aluminium scoop for use with cube moulds and other test equipment.
Code SCOOP
Description Scoop
Wire brush
Code W/BRUSH
Max/min thermometer
Code THER
44
Protection products
Rebar caps
A high visibility safety cap designed to t over the end of protruding rebar to reduce the risk of injury.
Frost blanket
A 10mm closed cell polyethylene foam designed to give good protection to concrete during low temperatures. They also make excellent curing mats during warmer temperatures as well.
Code FRO/BL
Hessian
Hessian rolls used for the protection and covering up of masonry and concrete.
Code HESSIAN
A polythene sheeting used for covering up and protection of building goods on site.
Code HDPS
Size 4m x 25m
Is a selected blend of inorganic acids for the removal of cementitious contamination and rust from a wide range of surfaces.
Code BRICK/05
Corner fenders
Designed to protect corners on columns in areas of builds which are prone to heavy trafcking such as multistorey car parks. Available with tangs for casting into concrete or with pre-drilled holes for surface xing after the column is cast.
Code C/FENDER
Gloves
A general purpose knit wrist pvc glove used for general protection of hands while handling building materials.
Code GLOVE
Pack 12 pairs
Protection sheet
A 2mm corrugated polypropylene sheet which is easy to cut, crease or curve to any site requirement. Available in standard or re rated grades. Sheet size: 2.44m x 1.22m (8 x 4). Telephone 0870 24 24 234
45
Ribslot 28/20
Halfen ribslot 28/20 is a self-anchoring channel which has been designed to achieve minimum deection. It is available in grade 304 stainless steel (S304) and a pre galvanised steel. Sizes available: 100mm, 150mm and 3000mm.
Description 100mm stainless 150mm stainless 100mm galv 150mm galv 3000mm galv
Halfen HTS-B channel ties are designed to bed into the mortar at one end and have a shouldered head that locates into a cast-in or surface xed channel at the other end available in grade 304 stainless steel (S304) and a pre galvanised mild steel. Sizes available: 75mm, 100mm, 150mm, 175mm & 200mm.
Description 75mm stainless 100mm stainless 150mm stainless 175mm stainless 200mm stainless 75mm galv
Pack 100 100 100 100 100 100 100 100 100 100
HTS/B/100G 100mm galv HTS/B/150G 150mm galv HTS/B/175G 175mm galv HTS/B/200G 200mm galv
A cold rolled channel with anchors designed for casting into concrete. The channel with its anchors, is attached to the formwork before casting. The void within the channel is lled with granulated expanded polystyrene which keeps the inside of the channel free from concrete during pouring and which is easily removed when xings are to be made. Full technical literature available on request. Types available: HTA 28/15, HTA 38/17, HTA 40/25, HZA 41/22. Standard lengths 3050mm & 6070mm. Cut lengths available on request. Grades available: A2 stainless steel and galvanised mild steel.
46
cont.
Halfen HTS-C cavity ties have been designed to meet the design and performance requirements of DD140. These ties are designed for a normal 10mm mortar bed. HTS-C ties come in standard shapes and lengths which will cover most applications. Grades available: stainless steel grade 304 (S304). Galvanised mild steel.
Halfen HTS-W wire ties are suitable for cavities up to 100mm. They are available in stainless steel grade 304 only. HTS-W2 tie meets DD140 type 2 requirements and complies to DD140 type 4. Lengths available: 200mm & 225mm
Halfen HTS-FS frame cramps are ties that bed into the mortar joint at one end and are surface xed to the structure through an upstand at the other end. HTS-FS frame cramps come in standard shapes and lengths which will cover most applications. Available in stainless steel grade 304 (S304). Sizes: 75mm, 100mm, 125mm, 150mm, 175mm and 200mm.
47
Featuring a turn-n-slide tie which enables the starter to be tied into any course the builder wishes, ideally every (225mm deep) block course or every third (75mm deep) bricks. Supplied in pack form only. Pack contents: Two 1165mm stainless steel lengths, ten ties, ve screws, wall plugs and washers
Code M/STARTER
An expanded stainless steel metal manufactured to BS EN 10088-1: 1995: 1.4301 (Grade 304/S15). Where greater strength is required to allow for uneven settlement and movement in buildings it is desirable to use exmet reinforcement in the joints. Material thickness (mm) 0.3 0.3 0.3 0.3 Coil size width (mm) 65 115 175 225
Expamet brickstrength
Reinforcement for mortar bed joints in brickwork. Manufactured from stainless steel type BS EN 10088-1,1.430.
Description 60mm brickstrength 100mm brickstrength 150mm brickstrength 175mm brickstrength 200mm brickstrength
48
cont.
Frame cramp
A safe edge frame cramp which provides positive location of window and door frames to masonry manufactured from pre-galvanised steel strip with zinc coated edges to BS EN 10142: 1991. Width (mm) 28 28 28 Length (mm) 100 150 200
Upstand (mm) 50 50 50
49
Tools
Wire brush
Code W/BRUSH
Mixing paddle
Used for the mixing of non shrink grouts and other powders. Manufactured to suit all heavy duty electrical drills.
Code PADDLE
Skeleton gun
Code SKELG
Used for the application of bitumen emulsion, primers and other liquids to concrete surfaces.
Code BRUSH
Scoop
An aluminium scoop for use with cube moulds and other test equipment.
Code SCOOP
Description Scoop
Sprayers
High performance sprayer units for the application of mould oil and chemical release agent.
Code MS08/S PS08 KN20 NOZZ LANCE TRIGGER GASK/M GASK/P SOLV/5 SOLV/25
Description 8ltr metal sprayer 8ltr plastic sprayer 20ltr knapsack Nozzle Sprayer lance Sprayer trigger unit Metal gasket set Plastic gasket set Cleaning solvent 5ltr Cleaning solvent 25ltr
Barrel accessories
Taps and pumps used in conjunction with plastic and metal barrels.
50
Tools
cont.
Carborundum stone
A carborundum rubbing block used to smoothen out uneven concrete repaired surfaces.
Code C/STONE
Hand floats
Buckets
Code BUCKET
The most popular tool used by all steel xers for the tying of reinforcement.
Code NIPS
Pack Each
Scraper
Code SCRAPER/LONG
Pack Each
Utility knife
A heavy duty utility knife pack which includes holder and spare blades.
Code S/KNIFE
Cranking Irons
A tool used for the straightening of rebar. Available in three sizes to cover a range of rebar diameters.
51
An aerosol spray used for marking or lining areas on site. Available in colours yellow, red, blue and white and packed 6 750ml cans per box.
A heavy duty highly visible orange polythene barrier fencing supplied in rolls. Roll size 1m x 50m
Code BARRIER
Size 1m x 50m
Fencing pins
A mild steel pin , pointed one end and a curled lamp hook on the other. Size: 1.35 metre long.
Code F/PIN
Size 1.350M
Hazzard tape
A white and red diagonally warning tape supplied in 500 metre rolls.
Code BARRIER/TAPE
Size 500m
52
11
33
12
41
13
44
15
46
21
51
25
67
26
77
All other shapes are shape code 99 and require a fully dimensional sketch Size Kg/m 8mm 0.222 10mm 0.395 135 12mm 0.888 94 16mm 1.579 53 20mm 2.466 34 25mm 3.854 22 32mm 6.313 13 40mm 9.864 8
12m/tonne 211
53
1. GENERAL The following Terms & Conditions apply to all agreements entered by the company for the Manufacturer and supply of its goods and services. No variation of our addition to the terms shall be valid unless authorised in writing by a Director of the company. 2. QUOTATIONS A quotation does not constitute an offer. No contract is concluded until written conrmation by the company is sent on receipt of order. 3. PERFORMANCES AND SPECIFICATION Any performance estimate is given without commitment and is based upon the companys experience only. Whilst every effort is made to ensure the accuracy of the details in our catalogue this is subject to a general acceptance of minor errors and omissions. 4. PRICE Prices quoted are based upon current conditions, costs of labour materials and statuary charges and are subject to increase without notice to take account of variations or alterations of the same. The company accordingly reserves the right to adjust invoice prices in the event of any increase in the cost of materials, transport or of labour and/or take account of any other costs that may arise in result of legalisation or by reason of any other event unknown to the company at the date of quotation. 5. PAYMENT The payment terms in the companys quotation must be strictly adhered to. In the event that payment is not made by the due date, the company shall be entitled to charge the customer interest on any overdue amount at the rate of 2% per month (or at such other rate as may be advised by the company from time to time). For each month or part month, which the said amounts, are to remain overdue. The customer shall not be entitled to retain, deduct or defer any sums whatsoever due to the company under the contract on account of any dispute, cross claim or set-off which it might have with the company. Non-compliance with payment terms will entitle the company to withhold further deliveries and/or labour forthwith. The companys delivery notice/invoice copy receipted on behalf of the customer or such other reasonable evidence as may be declared shall be sufcient proof of delivery for this purpose. 6. OWNERSHIP AND RISK (i) The risk of damage to any goods shall pass to the customer on delivery. (ii) Title to any goods shall not pass to the customer until the company has received payment in full of all accounts under each and every contract between the company and the customer existing at delivery. In the meantime, the goods shall remain property of the company and the customer shall hold them in a duciary capacity as the companys bailee free from any charge, lien or other encumbrance. During this period: (a) the customer shall keep the goods or any other property into which they are incorporated fully insured with a reputable insurer and if possible, store them separately and/or keep them in such a way that they can be clearly identied as the companys property; and (b) the company shall be entitled to recover possession of the goods (or any of them) at anytime to lawfully enter upon any of the customers (and for any reason) (and even by severance from other property) shall be entitled without restriction to lawfully enter upon any of the customers premises for that purpose. The customer shall pay all costs and expenses incurred by the company in exercising this right. (iii) Not withstanding that title may not have passed to the customer, the company may maintain an action for the price of the goods and the customer acknowledges that nothing in sub clause (ii) above confers any right to upon it to return or reject the goods or refuse, defer or delay payment from them. 7. DELIVERY AND [LIEN] (i) Although the company will use reasonable commercial endeavours to deliver goods within any time estimates given, time of delivery is not the essence of the contract and delay shall not therefore entitle the customer to repudiate. Neither shall the company be liable to the customer for any loss or damages whatsoever suffered or sustained as a result of the company failing to adhere to such times or dates. (ii) The company shall be entitled to deliver by single delivery or instalments. Without prejudice to sub clause (i) above, non-delivery of any instalment or delay in delivery shall not affect the balance of the contract or entitle the customer to terminate the same. However, the company shall be entitled to levy additional charges where the customer fails or refuses for any reason to take delivery and shall be entitled to determine the contract forthwith if the customer the fails to take delivery within fourteen days of a written request requiring them to do so. (iii) The company shall upon notice to the customer be entitled to withhold delivery or suspend performance of the contract generally if at the time of the notice any credit limit extended to the customer has been exceeded or payment of any of the companys invoices (whether related to the contract or not) is then overdue. If the customer fails within fourteen days of the notice to reduce its indebtedness to the level requested or to settle the said invoices, then the company shall, without further notice to the customer, be entitled to determine the contract forthwith. (iv) In addition to the above, the company shall (without prejudice to any other remedy available to it) have in respect of all unpaid debts and other sums due from the customer under the contract a general lien on any goods whatsoever in its possession (whether in relation to the contract or otherwise) which are or are intended to become the property of the customer and pursuant to that lien or right the company shall be entitled upon fourteen days written notice to the customer to sell any goods so held upon such terms as it thinks t and to keep the proceeds of sale thereof in diminution of the sum due to it and all costs and expenses incurred in or about effecting the sales.]
8. FAULTY GOODS AND LIMITATION ON LIABILITY (i) Whilst all reasonable care is taken in compiling technical data on the companys products all recommendations or suggestions regarding the use of such products are made without guarantee since the conditions of use are beyond the control of the company. It is the customers responsibility to satisfy them that each product is t for the purpose for which they intended to use it and the actual conditions of sale are suitable. (ii) Not withstanding that it will not be responsible for any defects caused or sustained as a result of variations in the customers original specications, the company warrants that its goods will be of satisfactory quality and that all service it provides by it will be performed with reasonable skill and care. Accordingly, the company will replace any goods that are defective, damaged or faulty at its own expense (provided that they have not been tampered with or subjected to improper treatments by the customer) if the customer gives written notice of the faults and defects within seven days of delivery. Goods to be replaced must be returned to the company properly packed and carriage paid before any replacement will be issued and notwithstanding clause 6(ii) hereof, goods so returned become the property of the company. (iii) Save as hereinbefore provided the company shall not be liable to compensate for indemnify the customer for any loss or damage (whether direct, indirect, consequential or otherwise) to or caused by or sustained as a result of the goods or services provided (iv) Not withstanding anything hereinbefore contained, the company is not seeking to exclude or restrict its potential liability for damage in the nature of death or the negligence or that of its servants or agents causes personal injury. However, the customer shall indemnify the company against all actions, claims, proceedings losses, costs, damages and expenses whatsoever arising in respect of loss of life or personal injury suffered by any person in connection with the contract where that loss of life or personal injury is caused by negligence of the customer or of its servants or agents. (v) A lm of rust or mill scale on reinforcement will not constitute grounds for rejection. 9. CANCELLATION The customer may not cancel all or any part of the contract without the written consent of the company. 10. INTELLECTUAL PROPERTY The patent, registered design, copyright and any other intellectual property rights attached to all goods and component parts, drawings, designs and plans of such goods are actually invented or designed by the company shall remain vested and the customer shall not therefore be entitled to copy to reproduce or procure the copying or reproduction of the same without the companys written consent. 11. FORCE MAJEURE In the event the normal course of the contract is frustrated, prevented, Interrupted, hindered delayed or rendered unduly expensive by any cause whatsoever beyond its control, the company shall promptly give notice thereof to the customer and shall have the right to cancel the contract or to defer its performance for as long as such force majeure shall continue. 12. PROPER LAW The construction, validity and performance of the contract shall be governed by English Law and all disputes shall govern the construction, validity and performance of the contract or the English Courts shall decide questions that may arise out of or in connection with or in relation to the contract. 1. Carriage paid on all orders except: (i) Orders less then 300 in invoice value and are subjected to a 20.00 delivery charge. (ii) Orders dispatched at the customers request by express delivery/courier, carriage at a cost. Deliveries are provided to customers requirements by or own transport. Deliveries are usually delivered within 48 hours of receipt of order for ex-stock items. All prices in the catalogue are exclusive of VAT The catalogue price list replaces all other price lists. All sales are subject to our standard terms and conditions of sale. Whilst all reasonable care is taken in complying technical data on the companys products are made without guarantee since the conditions of use are beyond the control of the company. It is the customers responsibility to satisfy himself that each product is t r the purpose for which he/she intends to use it and that actual conditions of use are suitable.
2. 3. 4. 5. 6. 7.
DELIVERY TO NEAREST HARD ROAD TO SITE Errors and omissions accepted. This applies to all aspects of our catalogue. ANCHOR BAY CONSTRUCTION PRODUCTS LTD & ANCHOR BAY BEAM FORM UNIT C 79 BANNING STREET GREENWICH LONDON SE10 ONT
54
Anchor Bay Construction Products Limited Unit C, 79 Banning Street, London SE10 ONT T: 0870 24 24 234 F: 0870 24 03 613 anchorbay@btclick.com www.anchor-bay.co.uk