Professional Documents
Culture Documents
TRR Integration Test Telstar14r Build3 (11!9!10)
TRR Integration Test Telstar14r Build3 (11!9!10)
DHS R.E. ACS R.E. DHS TEST R.E. Hua, Denise Tham, Calvin Vu, Binh Signature: Date:
DATABASE: Command Telemetry Sequence Mbus Sbus Block Macro Format Calibration Parameter Macro Verification Command Verification
Release Version t4_tc08.dbf t4_tm09.dbf t4_sq02.dbf t4_mb01.dbf t4_sb01.dbf t4_bc01.dbf t4_mc04.dbf t4_fo08.dbf t4_cd02.dbf t4_pa01.dbf t4_mv02.dbf t4_cv07.dbf
HARDWARE CONFIG :
DHE ACE BIGHUB SIMULATOR TAPS STREAMS: 234, 235, 236, 237, 238, 239
SCR #
SCR TITLE
SCR DESCRIPTION
Direction from propulsion engineering is to change the trip threshold for the monitor from 210 C (185 counts) to 242.72 deg C (198 Counts) MST Injection Temp Monitor STIRS 220 v2.doc E895-ST-220, Rev 1
TEST PLAN
STATUS/COMMENTS:
4015
4326
4336
ABM Parameters Update for Telstar-14R per Telstar-14R specifications and common product STIRS E895-ST-170 Rev 3 EPS Configuration based on Telstar-14R SOF Req 0696: NO SPTs with SPS Light architecture: Single PCU with 3 batteries: battery 1 with 18 cells, battery 2 with 18 cells, and battery 3 with 20 cells, and cell-derated capacity of 92Ah. REFER ABM FUNC Telstar-14R requires specific heater parameters updated per J948-ST-8 Appendix G. See attachments TEDoc-3452 rev3 Apdx G REFER THERMAL HEATERS FUNC Telstar-14R DHS Firmware needs to change Thermal Safe Setpoints as the followings: Thermal_Safe_N_Shunt_I_Limit => 172 Counts (10 Amps) Thermal_Safe_S_Shunt_I_Limit => 172 Counts (10 Amps) to reflect Telstar-14R SOF E461039 Rev 2 Req. REFER FDIR THERMAL SAFE MONITOR FUNC Telstar-14R DHS firmware needs to change Sun Pres Monitor as the followings: ACS_N_Solar_I_Limit_Soltice => 886 Counts (52 Amps) ACS_S_Solar_I_Limit_Soltice => 886 Counts (52 Amps) ACS_N_Solar_I_Limit_Equinox => 971 Counts (57 Amps) ACS_S_Solar_I_Limit_Equinox => 971 Counts (57 Amps) per Telstar-14R SOF E461039 Rev 2 Req. REFER FDIR SUN PRESENCE MONITOR FUNC T14R - A Patch is needed to correct DAPM Thermistors' Mux Addresses for T/V Testing. Telstar-14R requires specific heater parameters updated per J948-ST-8 Appendix G. See attachments TEDoc-3452 rev3 Apdx G
4338
4339
4589
4739
4589
The default telemetry encoder output voltage for Telstar14-R should be 4.4V(4 counts) per system System Eng. Email Req.
VERIFY BY MEMORY READOUT - Block 18, Offset 12, Bits 12-15 = 4 (currently is 7)
Release Checklist:
Worst Case Timing Report Total ROM\RAM Memory Usage Report Interrupts/Overrun/Overflows Verification Refer to WCT Report Refer to WCT Report Refer to WCT Report
Z:\opt\scribd\conversion\tmp\scratch6356\86389808.xls
Page 1 of 1
2/29/20127:12 PM