Professional Documents
Culture Documents
Tds Norox hdp-75 Global 112010
Tds Norox hdp-75 Global 112010
NOROX HDP-75
DESCRIPTION
NOROX HDP-75 is a solution of Methyl ethyl ketone peroxides and Cumyl hydroperoxide in phlegmatiser. NOROX HDP-75 is a liquid polymerisation initiator for the room temperature cure of unsaturated polyester and vinyl ester resins with the following advantages/properties: Very low peak exotherm temperature No viscosity build up i.e. better wetting properties between glass and resin Does not affect the green strength development Slower gel time then standard MEKP, for many resins. Excellent final cure both in thin and thick laminates Low impurity levels (water, MEK, salts) Less shrinkage and stress problems
TYPICAL PROPERTIES
Active oxygen content: Appearance: Specific Gravity at 20 C: Flash point (C.O.C.): SADT: Soluble in: Slightly soluble in: Storage temperature: 8.7 9.0 % Pale yellow liquid 1.09 1.13 g/cm 3 > 93 (> 199 C F) >60 ( > 140 C F) Oxygenated organic solvents Water Max 25 (77 C F)
APPLICATION
NOROX HDP-75 is an excellent initiator for unsaturated polyester and vinyl ester resin, when a lower peak exotherm is desired. Gel times will be slower compared to standard ANDONOX/NOROX MEKP products (i.e. KP-9, MEKP-925, -925H, etc) but final cured resin hardness is often better than for resins initiated with standard MEKPs. NOROX HDP-75 reduces or eliminates viscosity build up during the pre gel zone (thickening leading edge affect) commonly seen in conventional MEKP products. These properties lead to faster injection times in closed mould processes, such as vacuum infusion and RTM, and better wetting properties between the glass and the resin. The curing behaviour of NOROX HDP-75 reduces stress, cracking and shrinking problems in laminates & castings. Less shrinkage also means less fibre print through of gel coated surfaces. NOROX HDP-75 can be used when you want to build up thick laminates in one step, or if the laminate has big variations in thickness, or when you have high resin loadings. Typical applications are vacuum bag moulding (vacuum infusion) of big units, filament winding of pipes & tanks with thicker laminates or polyester concrete systems with high resin-to-filler ratio. Last but not least the NOROX HDP-75 does not affect the green strength development.
V2.01
NOROX HDP-75
CURE CHARACTERISTICS
A reactivity test (20 gram) with an unsaturated polyester resin gave the following results:
Resin: Initiator %: Isophthalic RTM polyester 1.5 Temperature: Accelerator % 25C pre-accelerated resin
A reactivity test (20 gram) with a vinyl ester (VE) resin gave the following results:
Resin: Initiator %: VE RTM resin 1.5 Temperature: Accelerator % 25 C pre-accelerated resin
Initiator
NOROX HDP-75 31 NOROX MEKP-925H 17 NOROX MEKP-9H 15 NOROX MCP-75 32 D = Shore D 5 = 935 Barcol
Barcol
Hardness at:
The information contained in this bulletin is based on information received of our staff and of others and is presented in good faith and with every belief in its accuracy. Due to the extensive technology involved in its usage, the manufacturer in no way guarantees such information, nor does he make any recommendations as to its use in the infringement of any patent. The information contained in this bulletin supersedes and replaces all information contained in all previous bulletins. Seller makes no warranty of any kind, expressed or implied, except that the goods sold hereunder shall meet the specifications of the buyer. After goods are accepted by the buyer within the time specified the buyer assumes all risk and liability for damages resulting from the use of the goods. Whether used by the buyer singly or in combination with other products, or if sold by buyer to third persons either in its original form or if repackaged by buyer and then sold to third persons.
SYRGIS PERFORMANCE INITIATORS www.syrgispi.com USA 334 Phillips 311 Road Helena, Arkansas 72342-9033 USA Phone +1 870 572 3610 Fax +1 870 572 3699 info@syrgis.com Europe Engelbrektsgatan 43B SE-11432 Stockholm Sweden Phone +46 8 545 121 60 Fax +46 8 545 121 70 info@syrgis.se