Professional Documents
Culture Documents
TEMS Investigation 10.0 IEs and Events
TEMS Investigation 10.0 IEs and Events
0
Information Elements and Events
This manual is provided by Ascom Network Testing AB without any kind of warranty. Improvements and changes in this description due to typographical errors or inaccuracies in current information, or improvements to programs and/or equipment may be made by Ascom Network Testing AB at any time without notice. These changes will, however, be incorporated into new editions of this manual. No part of this publication may be reproduced, transmitted, stored in a retrieval system, nor translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of the copyrighted owner, Ascom Network Testing AB. TEMS is a trademark of Ascom. All other trademarks are the property of their respective holders. Ascom 2009. All rights reserved. Publication number: LZT 108 9987 R1B
Contents
Contents
1. General
2 4
3.1. GSM Information Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.2. WCDMA Information Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 3.3. LTE Information Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 3.4. TD-SCDMA Information Elements . . . . . . . . . . . . . . . . . . . . . . . . 114 3.5. CDMA Information Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 3.5.1. iDEN Information Elements . . . . . . . . . . . . . . . . . . . . . . . . 153 3.6. WiMAX Information Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 3.7. Data Service Testing Information Elements . . . . . . . . . . . . . . . . . 162 3.8. Uplink (MTR) Information Elements . . . . . . . . . . . . . . . . . . . . . . . 166
169
4.1. General Information Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 4.2. GSM Information Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 4.2.1. GAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 4.2.2. GPRS/EGPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 4.2.2.1. Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 4.2.2.2. Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 4.2.3. Low Level Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 4.2.4. MS Behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 4.2.5. Neighbors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 4.2.6. Quality Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
4.2.7. Scan Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.8. Serving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.8.1. Channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.8.2. Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.8.3. Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.9. WCDMA Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3. WCDMA Information Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.1. Active Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.2. Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.3. Finger Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.4. GSM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.5. Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.6. HSDPA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.7. HSUPA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.8. Low Level Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.9. MS Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.10. Neighbors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.11. Network Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.12. Quality Measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.13. Radio Measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.14. SAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.15. Scan Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.16. Serving Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4. CDMA Information Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.1. Access Probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.2. Active Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.3. Active Set EV-DO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.4. Candidate Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.5. Candidate Set EV-DO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.6. Channel Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.7. Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.8. Finger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.9. Finger EV-DO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.10. Mobile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.11. Neighbor Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.12. Neighbor Set EV-DO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.13. Pilot Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.14. Polluters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.15. Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.16. Power EV-DO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.17. Quality Measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.18. Radio Measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
197 200 200 203 207 212 213 213 213 214 216 217 220 225 227 232 233 235 235 237 239 241 250 252 252 253 254 256 257 258 261 266 267 268 268 270 270 271 272 273 273 274
ii
Contents
4.4.19. Scan Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 4.4.19.1. Pilot Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 4.4.19.2. RSSI Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 4.4.20. Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 4.4.21. Session EV-DO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 4.4.22. Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 4.5. Data Service Testing Information Elements . . . . . . . . . . . . . . . . . 282
286
5.1. CDMA Information Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 5.2. GSM Information Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 5.3. WCDMA Information Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 5.4. LTE Information Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
7. Predefined Events
299
7.1. General Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299 7.2. GSM/WCDMA/TD-SCDMA Events . . . . . . . . . . . . . . . . . . . . . . . . 301 7.3. CDMA Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 7.3.1. Algorithm for Pilot Pollution and Missing Neighbor Detection in CDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 7.4. Data Events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
326
8.1. Preconfigured Status Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 8.1.1. General Status Windows (Route Analysis) . . . . . . . . . . . . 326 8.1.2. CDMA Status Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 8.1.2.1. Data Service Status Windows . . . . . . . . . . . . . . . . . 326 8.1.2.2. Other Status Windows. . . . . . . . . . . . . . . . . . . . . . . 327 8.1.3. GSM Status Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328 8.1.3.1. Data Service Status Windows . . . . . . . . . . . . . . . . . 328
iii
8.1.3.2. Interference Status Windows . . . . . . . . . . . . . . . . . 8.1.3.3. Uplink Status Windows (Data Collection) . . . . . . . . 8.1.3.4. Other GSM Status Windows . . . . . . . . . . . . . . . . . . 8.1.4. WCDMA Status Windows . . . . . . . . . . . . . . . . . . . . . . . . . 8.1.4.1. Data Service Status Windows. . . . . . . . . . . . . . . . . 8.1.4.2. Scanning Status Windows . . . . . . . . . . . . . . . . . . . 8.1.4.3. Other WCDMA Status Windows . . . . . . . . . . . . . . . 8.1.5. LTE Status Windows (Data Collection) . . . . . . . . . . . . . . . 8.1.6. WiMAX Status Windows (Data Collection) . . . . . . . . . . . . 8.1.7. iDEN Status Windows (Data Collection) . . . . . . . . . . . . . . 8.2. Preconfigured Event Counter Windows (Data Collection) . . . . . . 8.3. Preconfigured Message Windows . . . . . . . . . . . . . . . . . . . . . . . . 8.3.1. GSM Uplink Data Message Windows (Data Collection) . . 8.3.2. Analysis Message Windows . . . . . . . . . . . . . . . . . . . . . . . 8.3.3. Signaling Message Windows . . . . . . . . . . . . . . . . . . . . . . . 8.3.4. iDEN Message Windows (Data Collection) . . . . . . . . . . . . 8.4. Video Monitor (Data Collection) . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5. Preconfigured Line Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5.1. CDMA Line Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5.2. GSM Line Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5.3. WCDMA Line Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5.4. LTE Line Charts (Data Collection) . . . . . . . . . . . . . . . . . . . 8.5.5. WiMAX Line Charts (Data Collection) . . . . . . . . . . . . . . . . 8.5.6. iDEN Line Charts (Data Collection) . . . . . . . . . . . . . . . . . . 8.6. Preconfigured Bar Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6.1. CDMA Bar Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6.2. GSM Bar Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6.3. WCDMA Bar Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6.4. LTE Bar Charts (Data Collection) . . . . . . . . . . . . . . . . . . . 8.6.5. WiMAX Bar Charts (Data Collection) . . . . . . . . . . . . . . . . . 8.7. Preconfigured Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.8. GPS Window (Data Collection). . . . . . . . . . . . . . . . . . . . . . . . . . . 8.9. Presentation Window Templates . . . . . . . . . . . . . . . . . . . . . . . . .
329 329 330 331 331 332 333 334 334 335 335 335 335 335 336 337 337 338 338 338 339 340 340 341 341 341 342 342 343 343 344 344 345
346 353
iv
Chapter 1. General
1.
General
1.1.
This book catalogs all data presented in TEMS Investigation Data Collection and Route Analysis as well as all preconfigured presentation windows supplied in the two applications. Information elements in Data Collection and Route Analysis are covered in separate chapters. The IEs are mostly the same in both applications, but certain IEs as well as a number of entire IE categories are found only in Data Collection. A further reason for providing separate listings is the large number of minor differences between the applications in matters of naming, organization of arguments, and so on. These differences arise from the more sophisticated structuring of IEs in Route Analysis.
1.2.
Conventions
For the sake of brevity the following conventions are used in this book: The Data Collection Users Manual is referred to as DC UM. The Route Analysis Users Manual is referred to as RA UM.
2.
The information elements are divided into categories in the applications as follows: DC Section Ref. RA Section Ref. 4.1
Category General
Contents Elements reported by positioning equipment, and the Time element. (In Data Collection, these elements are found in technology-specific categories.) Elements reported by GSMcapable phones when in GSM mode, including GPRS/EGPRS elements and (where applicable) WCDMA and TD-SCDMA neighbor measurements. Elements from GSM scanning. Elements reported by GANcapable GSM phones when connected to a GAN.
GSM
3.1
4.2
Category WCDMA
Contents Elements reported by WCDMAcapable phones when in WCDMA mode, including HSPA elements and GSM neighbor measurements. Elements from WCDMA scanning. Elements from LTE scanning. Elements reported by TDSCDMA-capable phones when in TD-SCDMA mode, including (where applicable) GSM neighbor measurements. Elements reported by CDMA phones (including EV-DO and Analog elements). Elements reported by iDEN phones. Elements from CDMA scanning. Elements from WiMAX scanning. Elements relating to data service testing. These are not reported by phones but calculated by the TEMS Investigation software. Elements originating from GSM uplink data files.
LTE TD-SCDMA
3.3 3.4
CDMA
3.5
4.4
WiMAX Data
3.6 3.7
Not supported
4.5
GSM Uplink
3.8
Not supported
3.
The tables below list all information elements that can be presented by TEMS Investigation Data Collection. For ease of reference, each category on the Info Element tab is still covered in one single, alphabetically ordered list. (Certain deviations from strict alphabetical order occur in the application in order to achieve more logical orderings and groupings.) However, since the number and diversity of the information elements are great, a special column with codes is used in some tables to distinguish important subgroups among the elements.
3.1.
IE Support in Connectable Equipment Some elements are presentable only with a subset of the connectable devices. See the table in section 5.2, page 287. Properties of Information Elements: The Asterisk Column In the column marked *, a set of codes is used to state conditions under which an information element is valid: a non-trivial condition must be fulfilled for the element to be valid not valid: the element is normally valid, but in certain circumstances it is not (code ends in ) extended compared to the simplest GSM case: the element sometimes carries more information, for example when frequency hopping is used (code ends in +)
If nothing is written in the asterisk column, the element is always valid (provided it is supported by the device). Code c g g+ Valid if a cell file is loaded. Valid when running GPRS. Not valid for voice. The element is richer for (E)GPRS, in one of the following ways: g ga h more values, i.e. more arguments e.g. C/I Best values have a more complex meaning e.g. C/I Hopping List (average over timeslots) larger range of possible values e.g. Channel Type. Meaning
Not valid when running (E)GPRS. Valid in GAN mode or for GAN-capable phones. Valid if frequency hopping is used.
Code h+
Meaning The element is richer if frequency hopping is used. If frequency hopping is used, the element covers all channels in the hopping list. No GPRS connection: One value for each channel (arguments 0 through 63) GPRS: One value for each timeslot used on each channel (arguments 0 through 64 8 1 = 511). Exception: C/I Hopping List has only one value for each channel (arguments 0 through 63).
If frequency hopping is not used, the element contains values for the single channel employed. No GPRS connection: One single value (argument 0). GPRS: One value for each timeslot used on the channel (arguments 0 through 7).
Example: C/I Best. hc+ If frequency hopping is used, the element covers all channels in the hopping list. One value for each channel (arguments 0 through 63). No separate values for each timeslot for a GPRS connection. Example: C/I Hopping List. h hs hs+ Not valid if frequency hopping is used. Valid when running HSCSD. Not valid for voice. The element is richer for HSCSD, in one of the following ways: hs p more values, i.e. more arguments e.g. C/I Best values have a more complex meaning e.g. C/I Hopping List (average over timeslots) larger range of possible values e.g. Channel Type.
Code s si
Meaning Valid when some form of GSM scanning is undertaken (DC UM chapter 9). (Valid when doing interference scanning with a Sony Ericsson GSM phone.) This function is no longer supported in any connectable phone, but the information elements are retained in this description since old logfiles with interference scan data can still be replayed in the application.
Full and Sub Values Information elements with Full in their names are calculated on all blocks. Information elements with Sub in their names are calculated only on the blocks known to be sent also when downlink DTX is active (in each 104multiframe, one TCH block with SID information and one SACCH block). GSM RxLev Units GSM RxLev units are defined in 3GPP 45.008, section 8.1.4. Information Element Table
IE Name Adjacent RxLev Range/Unit 10 ... 100 GSM RxLev units Arg 1 ... 4 * h Description Signal strength of adjacent channel. Argument: 1: Serving cell 2 (400 kHz) 2: Serving cell 1 (200 kHz) 3: Serving cell +1 (+200 kHz) 4: Serving cell +2 (+400 kHz) Invalid if frequency hopping is used. Adjacent RxLev (dBm) 120 ... 10 dBm 1 ... 4 h Same as Adjacent RxLev but in dBm. Invalid if frequency hopping is used.
Range/Unit 0, 2
Arg
Description Use of C/A measurements in phone. See DC UM section 15.2.3.4. 0: Not activated 2: Activated
Altitude (ft)
Altitude (m)
Height above sea level in meters. Current active set of AMR speech codecs on downlink, each codec being described by a text string, e.g. 12.2 kbit/s rate. Argument: 0 gives the first member of the active set, etc.
0 ... 3
Text
0 ... 3
Current active set of AMR speech codecs on uplink, each codec being described by a text string, e.g. 12.2 kbit/s rate. Argument: 0 gives the first member of the active set, etc.
AMR C/I
5 ... 35 dB
C/I value used as input to mode control in AMR. This parameter is distinct from the ordinary C/I information elements, although the value should be similar. C/I limit for codec change to higher bit rate, calculated from AMR Hysteresis and AMR Threshold. C/I limit for codec change to lower bit rate, calculated from AMR Hysteresis and AMR Threshold.
5 ... 35 dB
5 ... 35 dB
Arg 0 ... 7
Description Distribution of downlink AMR codec usage for the current call. Invalid if no call is ongoing. Argument: Indicates the AMR codec. 0: 12.2 kbit/s 1: 10.2 kbit/s 2: 7.95 kbit/s 3: 7.40 kbit/s 4: 6.70 kbit/s 5: 5.90 kbit/s 6: 5.15 kbit/s 7: 4.75 kbit/s
0 ... 100 %
0 ... 7
Distribution of uplink AMR codec usage for the current call. Invalid if no call is ongoing. Argument: See AMR Codec Call DL (%).
0 ... 100 %
0 ... 7
Distribution of downlink AMR codec usage since the phone started using the current serving cell. Argument: See AMR Codec Call DL (%).
0 ... 100 %
0 ... 7
Distribution of uplink AMR codec usage since the phone started using the current serving cell. Argument: See AMR Codec Call DL (%).
0 ... 100 %
0 ... 3
Current distribution of downlink AMR codec usage across the active set being used. Argument: 0 gives the first member of the active set, etc., the members being ordered as in AMR Active Set DL.
Arg 0 ... 3
Description Current distribution of uplink AMR codec usage across the active set being used. Argument: 0 gives the first member of the active set, etc., the members being ordered as in AMR Active Set UL.
AMR Hysteresis
0 ... 15
1 ... 3
Hysteresis values in AMR mode switch mechanism. Argument: One hysteresis value for each possible mode transition (a maximum of four AMR codecs can be active simultaneously).
AMR Threshold
0 ... 63
1 ... 3
Threshold values in AMR mode switch mechanism. Argument: See AMR Hysteresis.
ARFCN BCCH
GSM 450: 259 ... 293 GSM 850: 128 ... 251 P-GSM 900: 1 ... 124 E-GSM 900: 0 ... 124, 975 ... 1023 GSM 1800: 512 ... 885 GSM 1900: 512 ... 810
10
Arg
* h
Description In idle mode: Same as ARFCN BCCH. In dedicated mode: Same as ARFCN TCH. Not valid when frequency hopping is used.
ARFCN TCH
Absolute Radio Frequency Channel Number of Traffic Channel. Valid only in dedicated mode and only for channels where no frequency hopping is used.
0 ... 60000 ms 0, 2
Time from Attach Request to Attach Complete. Use of band control function in phone. See DC UM sections 15.2.3.5, 15.2.3.12, 15.3.2.1, 15.4.1.1, 15.4.2.1, 15.4.3.1. 0: Not activated 2: Activated
0 ... 26 %
g hs
Bit error rate, calculated taking DTX into account, i.e. the figure is based only on blocks actually transmitted. Valid for voice only. Bit error rate for each used timeslot. Valid for data services only. Argument: 0 represents the first used timeslot (not TS 0), etc.
BER/Timeslot (%)
0 ... 26 %
0 ... 7
g hs
BLER/Timeslot (%)
0 ... 100 %
0 ... 7
g hs
Block error rate for each timeslot used. Valid for data services only. Argument: 0 means the first used timeslot (not TS 0), etc.
11
Range/Unit Text 00 ... 77 (octal) 0 ... 63 GSM RxLev units 100 ... 100 dB
Arg
Description Base Station Identity Code as text string. Base Station Identity Code in numeric format. Normalized signal level received at the MS (normalization with running average filter).
C/A 3
Carrier over Adjacent. Calculated as (RxLev for serving cell) (Adjacent RxLev for 3), i.e. the adjacent channels frequency is 600 kHz below the serving cells. Invalid if frequency hopping is used.
As C/A 3 but with adjacent channel at 400 kHz, 200 kHz, +200 kHz, +400 kHz, and +600 kHz respectively. Carrier-over-interference ratio for all channels. Argument = ARFCN. Concerning the range, see DC UM chapter 32.
C/I Absolute
5 ... 35 dB
12
Range/Unit 5 ... 35 dB
* g+ hs+ h+
Description C/I values for all hopping channels in all used timeslots. The whole list is sorted by descending C/I. For Nokia phones, a single C/I value is obtained (snapshot from the channel used at the time of measurement). This value is found at argument 0 of this element. For PCTel scanners, one C/I value is obtained for each channel scanned. Argument: 0 gives the C/I of the best channel, 1 gives that of the second best, etc.
0 ... 511
(8641)
g+ hs+ h+
ARFCN list corresponding to the C/I Best element (which see). Argument: 0 gives the ARFCN of the channel with the best C/I, etc.
0 ... 7
0 ... 511
(8641)
g hs h+
For multislot allocations: Timeslot list corresponding to the C/I Best element (which see). Argument: 0 gives the timeslot of the channel with the best C/I, etc.
5 ... 35 dB
0 ... 7
g hs h+
C/I for the worst channel in the hopping list for each used timeslot. Argument: 0 represents the first used timeslot (not TS 0), etc.
13
Range/Unit 5 ... 35 dB
Arg 0 ... 63
* g+ hs+ hc+
Description C/I values (unsorted) for the channels in the hopping list. For multislot channels, the mean value across all used timeslots is given. Argument: 0 gives the C/I of the first channel in the hopping list, etc.
0 ... 63
h+
ARFCNs of the channels in the hopping list (see C/I Hopping List). Argument: 0 gives the ARFCN of the first channel in the hopping list, etc.
5 ... 35 dB
C/I on the current BCCH. If frequency hopping is used, then if the BCCH is used as hopping frequency, report the C/I for that channel. If frequency hopping is not used, then if the BCCH is equal to the TCH, report its C/I. Invalid otherwise.
14
Range/Unit 5 ... 35 dB
* g+ hs+ h+
Description C/I values for all hopping channels in all used timeslots. The whole list is sorted by ascending C/I. For Nokia phones, a single C/I value is obtained (snapshot from the channel used at the time of measurement). This value is found at argument 0 of this element. For PCTel scanners, one C/I value is obtained for each channel scanned. Argument: 0 gives the C/I of the worst channel, 1 gives that of the second worst, etc.
0 ... 511
(8641)
g+ hs+ h+
ARFCN list corresponding to the C/I Worst element (which see). Argument: 0 gives the ARFCN of the channel having the worst C/I, etc.
0 ... 7
0 ... 511
(8641)
g hs h+
For multislot allocations: Timeslot list corresponding to the C/I Worst element (which see). Argument: 0 gives the timeslot of the channel having the worst C/I, etc.
C1
C2
15
IE Name C31
Arg
* g
Description GPRS signal strength threshold criterion C31. Valid both in packet idle and packet dedicated mode.
C32
GPRS cell ranking criterion C32. Valid both in packet idle and packet dedicated mode.
Text: Yes/No
EDGE supported/not supported in the cell. This information is available also to non-EDGE phones. Indicates whether GPRS is supported in the cell. Cell Identity. Same as Cell Id but coded as hexadecimal. c Name of serving cell. Present only if a cell file is used. Calculated using a number of different algorithms: see Cell Name Algorithm.
Cell Name
16
Range/Unit 1 ... 3
Arg
* c
Description Indicates the input used by the cell name determination algorithm and (for values 2 and 3) the result of the cell search: 1: MCC, MNC, LAC, and CI used. 2: BSIC, ARFCN, and position information used. Unique cell found matching these parameters within a 35 km radius. 3: BSIC, ARFCN, and position information used. Several matching cells found within a 35 km radius, closest cell selected.
CGI
Text
Cell Global Identity. Consists of Mobile Country Code, Mobile Network Code, Location Area Code and Cell Identity. Presented on the format MCC MNC LAC CI. Same as CGI, but LAC and CI coded as hexadecimal. Activity on channel: Signaling only, speech transmission, or data transmission. Measured signal strength level for all channels. Argument = ARFCN. Note: Unlike RxLev Full/RxLev Sub, this element is also updated by scan reports. Same as Channel RxLev but in dBm. Argument = ARFCN.
Text Text
Channel RxLev
17
Range/Unit Text
Arg
* g+ hs+
Description Channel type, also indicating which speech coder is used. For example, TCH/F + FACCH/ F and SACCH/M, BCCH, or PDCH. Currently used ciphering (A5/1, A5/2, GEA/1, etc.), whether for circuit-switched or packetswitched.
Ciphering Algorithm
Text
Coding Scheme DL
Text
Modulation coding scheme used on downlink. EDGE: One of: MCS-1 ... MCS-9, MCS-5-7, MCS-6-9, MCS-3 (pad), MCS-6 (pad). MCS-5-7 and MCS-6-9 are explained in 3GPP 44.060. (pad) means that an RLC block is retransmitted using MCS-3 and MCS-6 respectively. GPRS: One of CS-1 ... CS-4.
Coding Scheme DL Usage (Own Data) (%) Coding Scheme DL Usage (Total) (%) Coding Scheme UL
0 ... 100 %
1 ... 4
Distribution of coding scheme usage on downlink (for own data only). Argument: 1 means CS-1, etc.
0 ... 100 %
1 ... 4
Distribution of coding scheme usage on downlink (overall, not limited to own data). Argument: 1 means CS-1, etc.
Text
Modulation coding scheme used on uplink. For the possible values, see Coding Scheme DL.
18
Arg 0 ... 7
* g
Description These elements contain the distribution of coding scheme usage (on the downlink and for own data only) for each timeslot. Argument: 0 represents the first used timeslot (not TS 0), etc.
g g g g
Coding scheme currently used on downlink. Coding scheme currently used on uplink. Modulation coding scheme currently used on downlink. Modulation coding scheme currently used on uplink. Indicates whether the data transfer is performed over GPRS, EGPRS, or circuitswitched. Indicates whether the data transfer is performed over GPRS, EGPRS, or circuitswitched. 1: GPRS 2: EGPRS 3: CS
1 ... 3
0, 2
Use of Disable Handover function in phone. See DC UM section 15.2.3.9. Current value of Downlink Signalling Counter (DSC). Valid only in idle mode.
0 ... 45
19
Range/Unit 0 ... 45
Arg
Description Initial value of Downlink Signalling Counter (DSC). Valid only in idle mode.
0 ... 100 %
100
2 mandatory blocks are always sent using DTX: 1 TCH (with SID information) and 1 SACCH. Non-existent for packetswitched (no DTX). EGPRS BEP (Mean) 0 ... 31 See Description Mean value of bit error probability as reported in the Layer 3 message EGPRS Packet Downlink Ack/Nack. Coded according to the table in 3GPP 45.008, section 8.2.5. EGPRS BEP (Variance) 0 ... 7 See Description Variance of bit error probability as reported in the Layer 3 message EGPRS Packet Downlink Ack/Nack. Coded according to the table in 3GPP 45.008, section 8.2.5. EGPRS BEP Total (Mean) 0 ... 31 See Description Short-term mean value of bit error probability extracted from Layer 1. Coded according to the table in 3GPP 45.008, section 8.2.5. EGPRS BEP Total (Variance) 0 ... 7 See Description Short-term variance of bit error probability extracted from Layer 1. Coded according to the table in 3GPP 45.008, section 8.2.5.
20
IE Name EGPRS Link Quality Control UL EGPRS Window Size DL EGPRS Window Size UL FER Actual (%)
Range/Unit Text
Arg
Description Indicates whether Link Adaptation (LA) or Incremental Redundancy (IR) is used on the uplink. Retransmission buffer size on downlink (RLC protocol level). EDGE retransmission buffer size on uplink (RLC protocol level).
64 ... 1024 RLC blocks 64 ... 1024 RLC blocks 0 ... 100 %
g hs
Frame erasure rate, calculated taking DTX into account, i.e. the figure is based only on blocks actually transmitted. Valid for voice only.
0 ... 100 %
100
A block is erased when the parity check (CRC) fails. FER Sub (%) 0 ... 100 % Text 0, 2 Frame erasure rate, Sub value. For the calculation, see FER Full (%). Version number of device firmware. g Use of GPRS class forcing function in phone. Not supported by any currently connectable phones; see section 5.2 for details.
21
Range/Unit 0, 2
Arg
* g
Description Use of GPRS multislot class forcing function in phone. Not supported by any currently connectable phones; see section 5.2 for details.
0, 2
Use of power class forcing function in phone. 0: Not activated 2: Activated Not supported by any currently connectable phones; see section 5.2 for details.
0, 2
Use of PDP Context Request modification function in phone. Not supported by any currently connectable phones; see section 5.2 for details.
Frequency Band Frequency Band (Num) Frequency Band For TCH Frequent AQM IEs: General remark Frequent AQM Score DL Frequent AQM Score UL
Text
Frequency band of BCCH carrier, e.g. 850, 1800, 900E, 900R. Frequency band of BCCH carrier in numeric format. Frequency band of current traffic channel or channels, e.g. 850, 1800, 900E, 900R.
These elements, uplink and downlink scores, only appear in merged logfiles (see RA UM section 17.2). 1 ... 5 MOS-PESQ 1 ... 5 MOS-PESQ Frequent AQM score for last speech sentence played on the downlink. Frequent AQM score for last speech sentence played on the uplink.
22
Arg
Description Downlink Frequent AQM sentence index. Uplink Frequent AQM sentence index.
ga
State of GA-RC or GA-CSR protocol. 1: GA-RC Deregistered 2: GA-RC Registered 3: GA-CSR Idle 4: GA-CSR Dedicated
GA-RC/GACSR State (Text) GAN Access Point MAC Address GAN Access Point SSID GAN GERAN Cell Id
Text
ga
Same as GA-RC/GA-CSR State but in text format. MAC address of connected WLAN access point (BSSID in IEEE 802.11 standard). Service Set Identifier of connected WLAN access point. Cell Identity in the GSM EDGE Radio Access Network (GERAN). Included in Register and Discovery messages if the phone is in an area with GSM coverage and GSM-RR is the serving RR entity. Retrieved from GSM System Information. Location Area Code in the GSM network. Retrieved from GSM System Information. Mobile Country Code in the GSM network. Retrieved from GSM System Information. Mobile Network Code in the GSM network. Retrieved from GSM System Information.
Text
ga
ga ga
0 ... 65535
ga
ga
ga
23
Range/Unit 0 ... 3
Arg
* ga
Description Used to indicate the presence of GERAN coverage in the phones current location. 0: Normal service 1: Limited service 2: Phone has not found GERAN coverage 3: Phone has found GERAN coverage, service state unknown
Text
ga
Same as GAN GSM Coverage Indicator but in text format. Indicates to the GANC the number of times the phone has been redirected (from one GANC to another) without obtaining service. WLAN signal level. 0: Unusable 1: Poor 2: Adequate 3: Good 4: Excellent 5: Not applicable
0 ... 255
ga
0 ... 5
ga
GAN WLAN Quality Level (Text) GAN WLAN RSSI GANC IP Address GANC SEGW IP Address
Text
ga
Same as GAN WLAN Quality Level but in text format. WLAN received signal strength. Points to the default GANC the phone should use. Points to the default GANC Security Gateway the MS should use.
ga ga ga
24
IE Name GMM State GRR State Hardware Hardware ID Heading (deg) Hopping Hopping List
Range/Unit Text Text Text Text 0 ... 360 degrees Text Text
Arg
* g g
Description State of GMM protocol: Idle, Ready, or Standby. State of GRR protocol: Packet Idle or Packet Transfer. Device model. Device IMEI.
Direction of travel measured in degrees clockwise from north. Use of frequency hopping (YES/NO).
ARFCNs of the channels in the hopping frequency list, for example 1, 10, 19, 28. Hopping Sequence Number, indicating which hopping frequency list to use. Use of idle mode RxQual measurement function in phone. 0: Not activated 2: Activated Not supported by any currently connectable phones; see section 5.2 for details.
HSN
0 ... 63
0, 2
0, 2
Use of ignore/reverse cell barred function in phone. See DC UM sections 15.2.3.6, 15.3.2.3, 15.4.1.3, 15.4.2.2, 15.4.3.2. 0: Not activated 2: Activated
25
Arg
* si
Description The ARFCN scanned for interferers during interference scanning. Useful when replaying a logfile. (Interference scanning is no longer supported by any connectable phones.)
si
The BCCH ARFCN of the serving cell locked on during interference scanning. Useful when replaying a logfile. (Interference scanning is no longer supported by any connectable phones.)
Location Area Code. Same as LAC, but coded as hexadecimal. p p Latitude recorded by positioning equipment. Latitude as text. For the presentation format, see RA UM appendix C.4. Longitude recorded by positioning equipment. Longitude as text. For the presentation format, see RA UM appendix C.4. Percentage of LLC data blocks erroneously decoded on downlink. Percentage of LLC data blocks resent on uplink.
p p
26
IE Name LLC Bytes Received DL LLC Bytes Sent UL LLC Throughput DL (kbit/s) LLC Throughput UL (kbit/s) LLC Window Size DL LLC Window Size UL MAC Mode DL
Range/Unit 0 ... 2 109 bytes 0 ... 2 109 bytes 0 ... 400 kbit/s
Arg
* g
Description Number of bytes received at the LLC protocol level since PS attach. Number of bytes sent at the LLC protocol level since PS attach. Data throughput (including protocol headers, but excluding retransmissions) on downlink at the LLC protocol level. Data throughput (including protocol headers, but excluding retransmissions) on uplink at the LLC protocol level. LLC retransmission buffer size on downlink. LLC retransmission buffer size on uplink.
Type of GPRS connection on downlink: 0: Dynamic Allocation 1: Extended Dynamic Allocation 2: Fixed Allocation, not half duplex mode 3: Fixed Allocation, half duplex mode
g g g
Same as MAC Mode DL but in text format. Type of GPRS connection on uplink. See MAC Mode DL. Same as MAC Mode UL but in text format.
27
IE Name MAIO
Range/Unit 0 ... 63
Arg
* h
Description Mobile Allocation Index Offset. Indicates where in the hopping frequency list to start. Valid only if frequency hopping is used. Mobile Country Code. These elements contain the distribution of modulation coding scheme usage (on the downlink and for own data only) for each timeslot. Argument: 0 represents the first used timeslot (not TS 0), etc.
0 ... 7
Text
Contains the hexadecimal string of a Layer 3 message or mode report. Used for text-format logfile export only.
MNC Mode
Mobile Network Code. May consist of two or three digits. Same as Mode (Num) (which see) but in text format: No service etc. 1: No service 2: Idle mode 3: Dedicated mode 4: Limited service mode 5: Scan mode 6: Packet mode 7: Packet Idle mode Type of modulation on downlink. Type of modulation on uplink.
Mode (Num)
1 ... 7
Modulation DL Modulation UL
Text Text
28
Arg
Description Indicates whether the phones behavior has been changed from the default. Most of what follows is applicable only to Sony Ericsson GSM phones. Empty string: No modification of phone behavior B: Modification of behavior not related to channel selection (the information elements Adjacent Scan, Band Control, Forced Power Class, Idle Channel Quality) C: Modification of channel selection behavior (the information elements Disable Handover, Ignore Cell Barred, Prevent Handover List Active, Prevent Serving Cell List, Serving Cell List Active, Target Handover) G: Modification of GPRS behavior (the information elements Forced GPRS Class, Forced Multislot Class, Forced Quality Of Service). Any combination of these letters may appear.
Phone transmit power ordered by the base station, mapped to a number between 0 and 31 according to the tables in 3GPP 45.005, section 4.1.1. Valid only in dedicated mode.
29
Range/Unit GSM 850: 5 ... 39 GSM 900: 5 ... 39 GSM 1800: 0 ... 36 GSM 1900: 0 ... 33 dBm
Arg
Multiband Reporting
0, 2
Not used; the feature has been removed from TEMS Investigation. The element is retained in order to maintain compatibility with old logfiles.
A number of elements have been left out of the table. These are the Neighbor ... Band and SS ... elements, which are mere variants of the ordinary Neighbor elements and are used in the status window Serving + Neighbors By Band (see section 8.1.3). What differs is the sorting order: first by band and then, within each band, by signal strength. See ARFCN BCCH 1 ... 32 ARFCNs of neighbor cells, sorted by ARFCN. Argument: 1 gives the lowest ARFCN, etc.
Neighbor ARFCN
1 ... 32
ARFCNs of neighbor cells, sorted by signal strength. Argument: 1 represents the strongest neighbor, etc.
Neighbor BSIC
Text
1 ... 32
Base Station Identity Codes for neighbor cells (in text format), sorted by ARFCN. Argument: 1 represents the lowest ARFCN, etc.
30
Arg 1 ... 32
Description Base Station Identity Codes for neighbor cells (in numeric format), sorted by ARFCN. Argument: 1 represents the lowest ARFCN, etc.
Text
1 ... 32
Base Station Identity Codes for neighbor cells (in text format), sorted by signal strength. Argument: 1 represents the strongest neighbor, etc.
00 ... 77 (octal)
1 ... 32
Base Station Identity Codes for neighbor cells (in numeric format), sorted by signal strength. Argument: 1 represents the strongest neighbor, etc.
Neighbor C1
1 ... 32
Pathloss parameter C1 for neighbor cells, sorted by ARFCN. Argument: 1 represents the lowest ARFCN, etc.
Neighbor C1 (Sorted)
1 ... 32
Pathloss parameter C1 for neighbor cells, sorted by signal strength. Argument: 1 represents the strongest neighbor, etc.
Neighbor C2
1 ... 32
Cell reselection parameter C2 for neighbor cells, sorted by ARFCN. Argument: 1 represents the lowest ARFCN, etc.
Neighbor C2 (Sorted)
1 ... 32
Cell reselection parameter C2 for neighbor cells, sorted by signal strength. Argument: 1 represents the strongest neighbor, etc.
31
Arg 1 ... 32
* g
Description GPRS signal strength threshold criterion C31 for neighbor cells, sorted by ARFCN. Argument: 1 represents the lowest ARFCN, etc.
1 ... 32
GPRS signal strength threshold criterion C31 for neighbor cells, sorted by signal strength. Argument: 1 represents the strongest neighbor, etc.
Neighbor C32
1 ... 32
GPRS cell ranking criterion C32 for neighbor cells, sorted by ARFCN. Argument: 1 represents the lowest ARFCN, etc.
1 ... 32
GPRS cell ranking criterion C32 for neighbor cells, sorted by signal strength. Argument: 1 represents the strongest neighbor, etc.
Neighbor Cell Id
0 ... 65535
1 ... 32
Cell identities of neighbor cells, sorted by ARFCN. Decimal format. Argument: 1 represents the lowest ARFCN, etc.
0 ... 65535
1 ... 32
Cell identities of neighbor cells, sorted by signal strength. Decimal format. Argument: 1 represents the strongest neighbor, etc.
1 ... 32
Cell identities of neighbor cells, sorted by ARFCN. Hexadecimal format. Argument: 1 represents the lowest ARFCN, etc.
32
Arg 1 ... 32
Description Cell identities of neighbor cells, sorted by signal strength. Hexadecimal format. Argument: 1 represents the strongest neighbor, etc.
Text
1 ... 32
Names of neighbor cells, sorted by ARFCN. Present only if a cell file is used. Argument: 1 represents the lowest ARFCN, etc.
Text
1 ... 32
Names of neighbor cells, sorted by signal strength. Present only if a cell file is used. Argument: 1 represents the strongest neighbor, etc.
33
Range/Unit 1 ... 6
Arg 1 ... 32
* c
Description Indicates, for each neighbor cell, the input used by the algorithm determining the neighbor cell name, and the result of the cell search (where applicable): 1: MCC, MNC, LAC, CI used. 2: BSIC, ARFCN, and position information used. Unique cell found matching these parameters within a 35 km radius. 3: BSIC, ARFCN, and position information used. Several matching cells found within a 35 km radius, closest cell selected. 4: Serving cell found with the method denoted by Cell Name Algorithm = 1; this neighbor identified as a cell appearing in the serving cells neighbor list and having matching BSIC and ARFCN. 5: Serving cell found with the method denoted by Cell Name Algorithm = 2; this neighbor identified as a cell appearing in the serving cells neighbor list and having matching BSIC and ARFCN. 6: Serving cell found with the method denoted by Cell Name Algorithm = 3; this neighbor identified as a cell appearing in the serving cells neighbor list and having matching BSIC and ARFCN. Neighbors are sorted by ARFCN. Argument: 1 represents the lowest ARFCN, etc.
34
Range/Unit 1 ... 6
Arg 1 ... 32
* c
Description Same as Neighbor Cell Name Algorithm but sorted by signal strength. Argument: 1 represents the strongest neighbor, etc.
Neighbor LAC
0 ... 65535
1 ... 32
Location Area Codes for neighbor cells, sorted by ARFCN. Decimal format. Argument: 1 represents the lowest ARFCN, etc.
0 ... 65535
1 ... 32
Location Area Codes for neighbor cells, sorted by signal strength. Decimal format. Argument: 1 represents the strongest neighbor, etc.
1 ... 32
Location Area Codes for neighbor cells, sorted by ARFCN. Hexadecimal format. Argument: 1 represents the lowest ARFCN, etc.
1 ... 32
Location Area Codes for neighbor cells, sorted by signal strength. Hexadecimal format. Argument: 1 represents the strongest neighbor, etc.
Neighbor RxLev
1 ... 32
Received signal strength of neighbors, sorted by ARFCN. Argument: 1 represents the lowest ARFCN, etc.
1 ... 32
Received signal strength of neighbors, sorted in descending order. Argument: 1 represents the strongest neighbor, etc.
35
IE Name Neighbor RxLev (dBm) Neighbor RxLev (dBm) (Sorted) Neighbor (SI) ARFCN
Description Same as Neighbor RxLev but in dBm. Same as Neighbor RxLev (Sorted) but in dBm.
Neighbor list (obtained from System Information) of strongest cell scanned. The list is given in text format, for example: [ARFCN: 17, BSIC: 3-2] 7, 18, 32. The data within square brackets pertains to the strongest cell, and the neighbor ARFCNs follow.
Text
Cell reselection behavior of phone. One of NC0, NC1, NC2: NC0: MS reselection, no measurement reports NC1: MS reselection, measurement reports NC2: Network reselection See 3GPP 45.008, section 10.1.4.
Text
Handling of paging in the network. I: All paging on GPRS channels; Gs signaling interface present II: All paging on PCH; no Gs III: All circuit-switched paging on PCH, all packet-switched paging on PPCH; no Gs.
0 ... 64
36
IE Name Number Of Used Timeslots DL Number Of Used Timeslots UL PBCCH Timeslot PDCH IEs: General remark PDCH Utilization Control DL (%) PDCH Utilization Control UL (%) PDCH Utilization Other Data DL (%) PDCH Utilization Own Data DL (%) PDCH Utilization Own Data UL (%) PDCH Utilization Free Data UL (%) PDP IEs: General remark
Range/Unit 0 ... 8
Arg
* g hs g hs g
Description Number of timeslots in use on downlink. Number of timeslots in use on uplink. Timeslot used for PBCCH/ PCCCH, if any.
0 ... 8
0 ... 7
The argument represents a timeslot but is just a sequence number. That is, 0 represents the first used timeslot, 1 the second, etc.; the argument value does not equate to the corresponding timeslot index. 0 ... 100 % 0 ... 7 g Percentage of downlink PDCH capacity currently used for control signaling, or not used at all. Percentage of the available uplink PDCH capacity currently used for control signaling. Percentage of the downlink PDCH capacity currently used for other users data. Percentage of the downlink PDCH capacity currently used for own data. Percentage of the available uplink PDCH capacity currently used for own data. Percentage of the available uplink PDCH capacity that is currently unused.
0 ... 7
0 ... 7
0 ... 7
0 ... 7
0 ... 7
37
IE Name PDP Access Point Name PDP Address PDP Context Time (ms) PDP Contexts Active PDP Delay Class PDP LLC SAPI PDP Mean Throughput PDP NSAPI PDP Peak Throughput PDP Precedence Class PDP Radio Priority PDP Reliability Class PESQ IEs: General remark
Range/Unit Text Text 0 ... 60000 ms 0 ... 11 Text 3 ... 11 Text 5 ... 15 Text Text
* g g g
Description Host name or network address for each active PDP context. User address (IPv4/IPv6). Time from PDP Context Activation Request to PDP Context Activation Accept. Number of active PDP contexts. Delay class as defined by subscription. LLC Service Access Point Identifier. Mean throughput as defined by subscription. Network SAPI (Service Access Point Identifier). Peak throughput as defined by subscription. Precedence class as defined by subscription. Radio priority level as defined by subscription. Reliability class as defined by subscription.
g g g g g g g
Text Text
1 ... 11 1 ... 11
g g
Uplink PESQ scores only appear in merged logfiles. Downlink PESQ scores, as well as the remaining AQM measurements (all other elements prefixed with PESQ below), appear in merged as well as unmerged logfiles. However, prior to merging, all such data lags behind other data in the logfile. See RA UM section 17.2.2. 0 ... 100 dB AQM: Echo attenuation on downlink.
38
IE Name PESQ Echo Correlation PESQ Echo Delay PESQ Echo Power PESQ Score DL PESQ Score UL PESQ Sentence DL
Range/Unit 0 ... 5 0 ... 1000 ms 0 ... 100 dB 1 ... 5 MOS-PESQ 1 ... 5 MOS-PESQ 0 ... 3
Arg
Description AQM: Echo correlation on downlink. AQM: Echo delay on downlink. AQM: Echo power on downlink. AQM: PESQ score for last two speech sentences played on the downlink. AQM: PESQ score for last two speech sentence played on the uplink. AQM: Downlink PESQ sentence index. Each index represents the two sentences over which the corresponding PESQ score was calculated. 0: Sentences 0 + 1 1: Sentences 2 + 3 2: Sentences 4 + 5 3: Sentences 6 + 7
0 ... 3
AQM: Uplink PESQ sentence index. Same meaning as PESQ Sentence DL (which see). AQM: Volume on downlink. ga Indicates whether a selection has been made on the GAN Mode Selection tab of the phones property page. (At the outset no option is selected.) See DC UM section 15.4.3.4. 0: No 2: Yes
100 ... 20 dB 0, 2
39
Range/Unit 0, 2
Arg
Description Use of prevent handover function in phone (handover to certain cells prevented in dedicated mode). See DC UM section 15.2.3.9. 0: Not activated 2: Activated
0, 2
Use of prevent cell selection function in phone (camping on selected cells prevented in idle mode). See DC UM section 15.2.3.7. 0: Not activated 2: Activated
Q Search Power
Text
GPRS signal level criterion governing when to search for 3G cells (e.g. Above 74 dBm, Below 54 dBm, Always, Never). See 3GPP 45.008, section 10.4. g g Routing Area Code (8 bits). Same as RAC, but coded as hexadecimal. Current value of Radio Link Timeout counter. Uses the leaky bucket principle. Each decoded block increases the counter by 1 (if it is not already at max) and each failed block decreases the counter by 2. The call is terminated when the counter drops to 0. Valid only in dedicated mode.
4, 8, ..., 64
Initial value of Radio Link Timeout counter. Valid only in dedicated mode.
40
IE Name RLA_P
Range/Unit 10 ... 100 GSM RxLev units 120 ... 10 dBm 0 ... 100 % 0 ... 100 % 0 ... 127
Arg
* g
Description Received Level Average (GPRS signal strength measure). Same as RLA_P but in dBm. Percentage of RLC data blocks erroneously decoded on downlink. Percentage of RLC data blocks resent on uplink. RLC/MAC Block Sequence Number from header of data blocks. One element for each timeslot on downlink and uplink. For text-format logfile export only. Argument: Points to an individual GPRS radio block.
RLA_P (dBm) RLC BLER DL (%) RLC BLER UL (%) RLC Block BSN elements
g g
0 ... 23
g g
Text
0 ... 23
RLC/MAC block header as hex string (e.g. 80 1a 20), for both data and control blocks. One element for each timeslot on downlink and uplink. For text-format logfile export only. Argument: Points to an individual GPRS radio block.
41
Range/Unit 0 ... 31
Arg 0 ... 23
* g
Description RLC/MAC Temporary Flow Identifier from header of control and data blocks. One element for each timeslot on downlink and uplink. For text-format logfile export only. Argument: Points to an individual GPRS radio block.
Text
0 ... 23
RLC/MAC block type as string. Downlink: Data Block to this MS, Data Block to other MS, or Control Block. Uplink: Allowed but no data sent, Data block sent, Control Block sent, or Forbidden. One element for each timeslot on downlink and uplink. For text-format logfile export only. Argument: Points to an individual GPRS radio block.
Number of bytes received at the RLC protocol level since GPRS attach. Number of bytes sent at the RLC protocol level since GPRS attach. Data throughput (including protocol headers, but excluding retransmissions) on downlink at RLC protocol level.
42
Arg
* g
Description Data throughput (as defined above) on downlink at RLC protocol level, relative to theoretical maximum for current channel setup (coding scheme, number of timeslots). Data throughput (including protocol headers, but excluding retransmissions) on uplink at RLC protocol level. Data throughput (as defined above) on uplink at RLC protocol level, relative to theoretical maximum for current channel setup (coding scheme, number of timeslots). Percentage of RLP data blocks erroneously decoded on downlink. Percentage of RLP data blocks resent on uplink. Number of bytes received at the RLP protocol level since dialup. Number of bytes sent at the RLP protocol level since dialup. Data throughput (including protocol headers, but excluding retransmissions) on downlink at RLP protocol level. Data throughput (as defined above) on downlink at RLP protocol level, relative to theoretical maximum for current channel setup (coding scheme, number of timeslots).
0 ... 100 %
RLP BLER DL (%) RLP BLER UL (%) RLP Bytes Received DL RLP Bytes Sent UL RLP Throughput DL (kbit/s) RLP Throughput DL (%)
0 ... 100 % 0 ... 100 % 0 ... 2 109 bytes 0 ... 2 109 bytes 0 ... 60 kbit/s
hs
hs hs
hs
hs
0 ... 100 %
hs
43
Arg
* hs
Description Data throughput (including protocol headers, but excluding retransmissions) on uplink at RLP protocol level. Data throughput (as defined above) on uplink at RLP protocol level, relative to theoretical maximum for current channel setup (coding scheme, number of timeslots). Received signal strength (Full value) expressed in GSM RxLev units. Received signal strength (Full value) expressed in dBm. Same as RxLev Full but valid only when the phone is in idle, dedicated, packet idle, or packet dedicated mode. Not valid when in limited service or no service mode. Same as RxLev Full (dBm) but valid only when the phone is in idle, dedicated, packet idle, or packet dedicated mode. Not valid when in limited service or no service mode. Received signal strength (Sub value) expressed in GSM RxLev units. Received signal strength (Sub value) expressed in dBm.
0 ... 100 %
hs
RxLev Full
10 ... 100 GSM RxLev units 120 ... 10 dBm 10 ... 100 GSM RxLev units
RxLev Sub
44
Arg
Description Same as RxLev Sub but valid only when the phone is in idle, dedicated, packet idle, or packet dedicated mode. Not valid when in limited service or no service mode. Same as RxLev Sub (dBm) but valid only when the phone is in idle, dedicated, packet idle, or packet dedicated mode. Not valid when in limited service or no service mode. Received signal quality (Full value), calculated from the bit error rate according to the table in 3GPP 45.008, section 8.2.4. Bit error rate in percent (%) corresponding to RxQual Full. Received signal quality (Sub value), calculated from the bit error rate according to the table in 3GPP 45.008, section 8.2.4. Bit error rate in percent (%) corresponding to RxQual Sub.
RxQual Full
0 ... 63 h+
C/A measurement: ARFCNs of channels at 400 kHz. Argument: 0 means the channel adjacent to the first channel in the hopping list, etc.
0 ... 63
h+
Same as Scanned Adjacent ARFCN 2 but for the channels at 200 kHz.
45
Arg 0 ... 63
* h+
Description C/A measurement: ARFCNs used by current serving cell. BCCHs are shown in idle mode, TCHs in dedicated mode. Note that this element does not itself refer to an adjacent channel but to the C0. Argument: 0 means the first channel in the hopping list, etc.
Scanned Adjacent ARFCN +1 Scanned Adjacent ARFCN +2 Scanned Adjacent RxLev 2 (dBm)
0 ... 63
h+
Same as Scanned Adjacent ARFCN 2 but for the channels at +200 kHz. Same as Scanned Adjacent ARFCN 2 but for the channels at +400 kHz. C/A measurement: Scanned signal strength of the channels at 400 kHz. Argument: 0 gives the RxLev of the channel adjacent to the first channel in the hopping list, etc.
0 ... 63
h+
0 ... 63
h+
0 ... 63
h+
C/A measurement: Same as Scanned Adjacent RxLev 2 (dBm) but applies to channels at 200 kHz. C/A measurement: Scanned signal strength of the channels used by the current serving cell. That is, BCCHs in idle mode and TCHs in dedicated mode. Note that this element does not itself refer to an adjacent channel but to the C0. Argument: 0 gives the RxLev of the first channel in the hopping list, etc.
0 ... 63
h+
46
IE Name Scanned Adjacent RxLev +1 (dBm) Scanned Adjacent RxLev +2 (dBm) Scanned ARFCN
Arg 0 ... 63
* h+
Description C/A measurement: Same as Scanned Adjacent RxLev 2 (dBm) but applies to channels at +200 kHz. C/A measurement: Same as Scanned Adjacent RxLev 2 (dBm) but applies to channels at +400 kHz. ARFCNs of scanned channels. Argument: 0 points to the channel with the lowest frequency, etc. (not ARFCN).
0 ... 63
h+
0 ... 846
Scanned Band
0 ... 846
Frequency bands of scanned channels in numeric format. Argument: 0 points to the channel with the lowest frequency, etc. (not ARFCN).
Scanned BSIC
00 ... 77 (octal)
0 ... 846
BSICs of scanned channels. Argument: 0 gives the BSIC of the channel with the lowest frequency, etc. (not ARFCN).
00 ... 77 (octal)
h+
C/A measurement: C/A values corresponding to Scanned Adjacent RxLev 2 (dBm). C/A measurement: C/A values corresponding to Scanned Adjacent RxLev 1 (dBm). C/A measurement: C/A values corresponding to Scanned Adjacent RxLev +1 (dBm).
0 ... 63
h+
0 ... 63
h+
47
Arg 0 ... 63
* h+
Description C/A measurement: C/A values corresponding to Scanned Adjacent RxLev +2 (dBm). C/I values for scanned channels. Argument: 0 gives the cell name for the channel with the lowest frequency, etc. (not ARFCN).
0 ... 846
Text
0 ... 846
c s
Cell names for scanned channels. Obtained only if both ARFCN and BSIC are scanned. Argument: 0 gives the cell name for the channel with the lowest frequency, etc. (not ARFCN).
0 ... 847
Number of channels currently scanned. Received signal strength of scanned channels (GSM scan or RSSI scan). Argument: 0 gives the RxLev of the channel with the lowest frequency, etc. (not ARFCN).
0 ... 846
0 ... 846 See range of ARFCN BCCH See range of ARFCN BCCH
s s
Same as Scanned RxLev but in dBm. Received signal strength of scanned channels (GSM scan or RSSI scan). Argument: ARFCN.
48
Range/Unit 0, 1, 2
Arg
Description Use of lock on channel function in phone. See DC UM sections 15.2.3.7, 15.3.2.1, 15.4.1.2, 15.4.2.1. 0: Not activated 1: Ordered by user, but not yet activated 2: Activated
0 ... 63
h+
Signal strength of each channel in the hopping list. This element thus gives more information than RxLev, which is an average over all channels in the hopping list. Argument: 0 means the first channel in the hopping list, etc.
49
Arg
Description Signal strength on the current BCCH. Especially useful for obtaining a correct measure of the cell size when frequency hopping is used and power control is applied to the TCHs. The following steps are used to find a value for the element: 1. Neighbor list. If the BCCH frequency is in the neighbor list, report its signal strength. 2. Hopping list. If the BCCH is used as hopping frequency (in dedicated mode), report its signal strength. 3. Idle mode. If the phone is in idle mode, report RxLev (dBm). If frequency hopping is not used, step 2 becomes If BCCH = TCH .... Invalid if no value is found in any of the above steps.
SNDCP BLER DL (%) SNDCP BLER UL (%) SNDCP Bytes Received DL SNDCP Bytes Sent UL
0 ... 100 % 0 ... 100 % 0 ... 2 109 bytes 0 ... 2 109 bytes
Percentage of SNDCP data blocks erroneously decoded on downlink. Percentage of SNDCP data blocks resent on uplink. Number of bytes received at the SNDCP protocol level since GPRS attach. Number of bytes sent at the SNDCP protocol level since GPRS attach.
g g
50
IE Name SNDCP Throughput DL (kbit/s) SNDCP Throughput UL (kbit/s) Speech Codec Speech Path Delay
Arg
* g
Description Data throughput (including protocol headers, but excluding retransmissions) on downlink at SNDCP protocol level. Data throughput (including protocol headers, but excluding retransmissions) on uplink at SNDCP protocol level. Currently used speech codec, e.g. EFR. AQM: The length of time it takes for the speech to travel from the Call Generator to the MTU and back to the Call Generator again. This element only appears in merged logfiles (see RA UM section 17.2).
p p
51
IE Name SQI
Arg
* g
Description Speech Quality Index. See DC UM chapter 28. The range depends on the speech codec used: HR (Half Rate): 20 ... 17 dBQ FR (Full Rate): 19 ... 22 dBQ EFR (Enhanced Full Rate): 20 ... 30 dBQ AMR: Dependent on codec mode. The maximum SQI values are as follows: 12.2 kbit/s: 30 dBQ 10.2 kbit/s: 28 dBQ 7.95 kbit/s: 28 dBQ 7.40 kbit/s: 27 dBQ 6.70 kbit/s: 27 dBQ 5.90 kbit/s: 24 dBQ 5.15 kbit/s: 21 dBQ 4.75 kbit/s: 19 dBQ Non-existent for GPRS (no voice data in packets).
0 ... 846
g s
SQI expressed on the MOS scale. See DC UM chapter 28. ARFCNs of scanned channels sorted by decreasing signal strength. Argument: Except in the case of neighbor list scanning, 0 means the strongest channel of those currently scanned, etc. When neighbor list scanning is performed, all neighbors come first, and then all other channels follow, both channel sets being sorted internally by decreasing signal strength.
52
* s
Description Frequency bands of scanned channels sorted by decreasing signal strength. Argument: See Strongest Scanned ARFCN.
Text
0 ... 846
BSICs of scanned channels sorted by decreasing signal strength. Argument: See Strongest Scanned ARFCN.
5 ... 35 dB
0 ... 846
C/I for scanned channels sorted by decreasing signal strength. Argument: See Strongest Scanned ARFCN.
Text
0 ... 846
c s
Names of scanned channels sorted by decreasing signal strength. Obtained only if both ARFCN and BSIC are scanned. Argument: See Strongest Scanned ARFCN.
0 ... 846
Signal strength of scanned channels in descending order. Argument: See Strongest Scanned ARFCN.
0 ... 7
Number of subchannel used in SDCCH or TCH half-rate channel. Timing Advance. Valid only in dedicated mode. For the significance of the parameter value, see 3GPP 45.010.
53
Range/Unit 0, 1, 2
Arg
Description Use of lock handover function in phone (handover restricted to a chosen set of cells; see DC UM section 15.2.3.9). 0: Not activated 1: Ordered by user, but not yet activated 2: Activated
0 ... 127
1 ... 32
Neighbor Cell Parameter Identity of TD-SCDMA cell measured by TD-SCDMA capable phone while in GSM mode. Argument: Neighbors sorted by signal strength in descending order.
1 ... 32
Number of TD-SCDMA neighbors measured in GSM mode. Received signal code power of each TD-SCDMA neighbor measured in GSM mode. UARFCN of each TD-SCDMA neighbor measured in GSM mode.
1 ... 32
1 ... 32
TFI DL
Temporary Flow Id on uplink. Used to identify a one-block flow. Temporary Flow Id on downlink. Used to identify a one-block flow. Current time in text format: HH:MM:SS.mm, where mm = decimal seconds.
TFI UL
0 ... 31
Time
Text
54
IE Name Timeslot IEs: General remark Timeslot Timeslot Channel Type DL Timeslot Channel Type UL Timeslot Used DL Timeslot Used UL TLLI TLLI (Hex) Training Sequence Code Uplink State Flag
Range/Unit
Arg
Description
The argument, where present, represents a timeslot but is just a sequence number. That is, 0 represents the first used timeslot, 1 the second, etc.; the argument value does not equate to the corresponding timeslot index. 0 ... 7 Text 0 ... 7 g hs g hs g hs g hs g g Timeslot used for current call. Valid only in dedicated mode. Type of channel in each timeslot on downlink. See Channel Type. Type of channel in each timeslot on uplink. See Channel Type. Timeslots used on downlink. Timeslots used on uplink. Temporary Logical Link Identifier. Same as TLLI, but coded as hexadecimal. Current training sequence code. g Uplink State Flags, one for each timeslot, indicating to the phone when it is allowed to send. Argument: Timeslot sequence number (compare Timeslot IEs: General remark).
Text
0 ... 7
0 ... 7 0 ... 7
0 ... 7
0 ... 7
34 ... 0 dB
1 ... 32
CPICH Ec/No of measured WCDMA neighbors. Argument: 1 gives the neighbor with the highest signal strength, etc.
55
Arg 1 ... 32
Description CPICH RSCP of measured WCDMA neighbors. Argument: See WCDMA Neighbor CPICH Ec/No.
0 ... 511
1 ... 32
Scrambling codes of measured WCDMA neighbors. Argument: See WCDMA Neighbor CPICH Ec/No.
1 ... 32
ARFCNs of measured WCDMA neighbors. Argument: See WCDMA Neighbor CPICH Ec/No.
Number of measured WCDMA neighbors. s ARFCNs of scanned channels sorted by increasing signal strength. Argument: Except in the case of neighbor list scanning, 0 means the weakest channel of those currently scanned, etc. When neighbor list scanning is performed, channels are sorted exactly in the opposite order to Strongest Scanned ARFCN. (The Weakest element serves no purpose in this context.)
0 ... 846
0 ... 846
Frequency bands of scanned channels sorted by increasing signal strength. Argument: See Weakest Scanned ARFCN.
56
Range/Unit Text
* s
Description BSIC of scanned channels sorted by increasing signal strength. Argument: See Weakest Scanned ARFCN.
5 ... 35 dB
0 ... 846
C/I for scanned channels sorted by increasing signal strength. Argument: See Weakest Scanned ARFCN.
Text
0 ... 846
c s
Names of scanned channels sorted by increasing signal strength. Obtained only if both ARFCN and BSIC are scanned. Argument: See Weakest Scanned ARFCN.
0 ... 846
Signal strength of scanned channels in ascending order. Argument: See Weakest Scanned ARFCN.
57
3.2.
This category contains all information elements reported by UEs in WCDMA mode, including measurements on GSM neighbors performed while in WCDMA mode. The WCDMA scanning elements are also found here, as well as miscellaneous other items (e.g. time, positioning information). Properties of Information Elements: The Asterisk Column In the column marked *, a set of codes is used to identify certain groups of information elements: Code c dv ne ns p pi rs ss ts Meaning Requires that a cell file has been loaded. Reported when running DVB-H. GSM neighbor measurements reported by the UE while in WCDMA mode. Reported from network search scanning. Reported by positioning equipment, or requires positioning data to make sense. Reported from pilot scanning. Reported from RSSI scanning. Reported from spectrum scanning. Reported from SCH timeslot scanning.
Notes on Quantities Denoting Signal Power Below is a list of the signal power and power ratio quantities that appear in the names of information elements. Eb: Scrambling code energy per bit. Ec: Scrambling code energy per chip.
58
Es: Scrambling code energy per chip (as measured by a scanning device during the SCH timeslot scan). No: Total energy per chip (as measured by a UE). Io: Total energy per chip (as measured by a scanning device). Ec/No: Signal-to-noise ratio (as measured by a UE). See 3GPP 25.215, section 5.1.5. Compare No above. Ec/Io: Signal-to-noise ratio (as measured by a scanning device). Compare Io above. SIR: Signal-to-interference ratio as measured on the DPCCH. See 3GPP 25.215, section 5.2.2. RSCP: Received signal code power, identical with Ec: see 3GPP 25.215, section 5.1.5. RSSI: Received signal strength indicator, identical with No: see 3GPP 25.215, section 5.1.5.
that is,
Altitude (m)
These elements are valid also in GSM mode, where they appear side by side with the more elaborate GSM-specific elements relating to AMR (see section 3.1).
59
Range/Unit Text
Arg 1 ... 8
Description Names of AMR codecs. Argument: Identifies the AMR codec. 1: 12.2 kbit/s 2: 10.2 kbit/s 3: 7.95 kbit/s 4: 7.40 kbit/s 5: 6.70 kbit/s 6: 5.90 kbit/s 7: 5.15 kbit/s 8: 4.75 kbit/s
0 ... 100 %
1 ... 8
Current distribution of AMR codec usage on downlink. Argument: See AMR Codec Name.
0 ... 100 %
1 ... 8
Current distribution of AMR codec usage on uplink. Argument: See AMR Codec Name.
AS Cell Name
Text
1 ... 6
Cell name of each active set member. Argument: Active set ID identifying an active set member.
AS CPICH Ec/No
34 ... 0 dB
1 ... 6
CPICH Ec/No of each active set member. Argument: Active set ID.
AS CPICH RSCP
1 ... 6
CPICH received signal code power of each active set member. Argument: Active set ID.
AS No Of Members
0 ... 6
The number of base stations in the active set. Valid only in state Cell_DCH.
60
IE Name AS SC
Arg 1 ... 6
Description Scrambling code of each active set member. Argument: Active set ID.
AS UARFCN DL
1 ... 6
Downlink UARFCN of each active set member. Argument: Active set ID.
Bit error rate, measured using either the pilot bits or the TPC bits on the DPCCH channel (choice depends on slot format). Reported in Q11 format. A 100% error figure means 2047 detected errors. Averaged over reporting period.
0 ... 63
BLER Tar get value set on phone property page (DC UM section 15.2.3.14), overriding BLER target set by network. Same as BLER Target Control but in text format. Calculated as: # ends / (# blocks + # drops + # ends) where blocks = Blocked Call events drops = Dropped Call events ends = Call End events Only events occurring in WCDMA mode are counted.
0, 1
Use of cell barring related functions in phone. See DC UM sections 15.2.3.13, 15.3.2.3, 15.4.1.3, 15.4.2.2.
61
Range/Unit Text 0, 1
Arg
Description Same as Cell Barred Control but in text format. Use of compressed mode. 0: False 1: True
CW scanning: Synonymous with RSSI scanning. See DC UM section 10.4. CW Sc No of UARFCNs CW Sc RSSI 0 ... 255 130 ... 20 dBm 1 ... 255 rs rs RSSI scanning: Number of UARFCNs scanned. RSSI scanning: RSSI of UARFCNs scanned. Argument: The channels are sorted by ascending UARFCN. The argument 1 gives the channel with the lowest UARFCN. CW Sc UARFCN 0 ... 16383 (frequency band dependent) 1 ... 255 rs RSSI scanning: UARFCNs of channels scanned, sorted in ascending order. Argument: 0 gives the first channel currently scanned, 1 the second, etc. 1 ... 6 c Cell name of each detected neighbor. Argument: Neighbor identity. Det Neigh CPICH Ec/No 34 ... 0 dB 1 ... 6 CPICH Ec/No of each detected neighbor. Argument: Neighbor identity. Det Neigh CPICH RSCP 140 ... 15 dBm 1 ... 6 CPICH received signal code power of each detected neighbor. Argument: Neighbor identity. Det Neigh CPICH Tx Power 31 ... 50 dBm 1 ... 6 CPICH transmit power of each detected neighbor. Argument: Neighbor identity.
Text
62
Arg 1 ... 6
Description Number of detected neighbors. Pathloss of each detected neighbor. Calculated as Primary CPICH Tx Power CPICH RSCP. Argument: Neighbor identity.
Det Neigh SC
0 ... 511
1 ... 6
0 ... 16383 (frequency band dependent) 135 ... 15 dBm 135 ... 15 dBm 0 ... 100 % 0 ... 100 % 5 ... 35 dB 0 ... 100 %
1 ... 6
DPCCH ISCP DL DPCCH RSCP DL DTX Rate DL DVB-H BER DVB-H C/N DVB-H MFER
dv dv dv
DPCCH interference signal code power on downlink. DPCCH received signal code power on downlink. Use of DTX on downlink for the voice service. DVB-H bit error rate. DVB-H carrier-to-noise ratio. DVB-H frame error rate after MPE-FEC decoding. See ETSI TR 102 377 V1.2.1, section 10.3.2.1. DVB-H received signal power.
DVB-H Rx Power
dv
63
Range/Unit
Arg
Description
The Rake fingers are not sorted by signal strength; they come in the order they are reported. The ordinal (1st, etc.) refers to a UMTS frequency. Separate sets of Finger elements are provided for the full number of UMTS frequencies that can be scanned simultaneously. The Motorola E1000 may report finger measurements on a number of different channels (see the elements Finger ... Position Type); the other devices that support finger measurements always report them on the CPICH. The Finger and Finger Position series of elements contain the same data. The latter series consists of arrays of size 2560 corresponding to the sequence of chips in a radio frame timeslot, with the received finger information positioned at the correct indices. These elements are provided for bar chart plotting. The Finger Slot Pos element is of course not needed in the Finger Position series and is consequently absent from it.
Finger ... Ec/No Finger ... No of Finger ... RSCP Finger ... RSSI
34 ... 0 dB 0 ... 48 140 ... 15 dBm 130 ... 20 dBm 0 ... 511
1 ... 48
1 ... 48
Total number of Rake fingers. RSCP for each Rake finger. Argument: Rake finger number.
1 ... 48
Finger ... SC
1 ... 48
Scrambling code for each Rake finger. Argument: Rake finger number.
0 ... 15
1 ... 48
Radio frame timeslot index for each Rake finger. Argument: Rake finger number.
1 ... 2560
1 ... 48
Position (chip index) of each Rake finger within the radio frame timeslot. Argument: Rake finger number.
64
Range/Unit Text
Arg 1 ... 48
Description Type of channel on which each Rake finger is reported (e.g. CPICH). Argument: Rake finger number.
1 ... 48
1 ... 2560
Same as Finger ... Ec/No (see general remarks). Argument: Chip index.
1 ... 2560
Same as Finger ... RSCP (see general remarks). Argument: Chip index.
1 ... 2560
Same as Finger ... RSSI (see general remarks). Argument: Chip index.
0 ... 511
1 ... 2560
0 ... 15
1 ... 2560
Same as Finger ... Slot (see general remarks). Argument: Chip index.
Text
1 ... 2560
Same as Finger ... Type (see general remarks). Argument: Chip index.
1 ... 2560
Same as Finger ... UARFCN (see general remarks). Argument: Chip index.
Firmware Version
65
Range/Unit
Arg
Description
See the description (cellular technology independent) under GSM, page 22. See section 3.1 under ARFCN BCCH 1 ... 32 ne ARFCNs of measured GSM neighbors. Argument: 1 gives the neighbor with the highest signal strength, etc. 1 ... 32 ne Base Station Identity Codes (in text format) of measured GSM neighbors. Argument: See GSM Neigh ARFCN.
Text
1 ... 32
ne ne
Number of measured GSM neighbors. Received signal strength of measured GSM neighbors. Argument: See GSM Neigh ARFCN.
Device model. Direction of travel measured in degrees clockwise from north. Type of latest handover. 0: Unknown (e.g. because no cell file loaded) 1: Soft 2: Softer 3: Hard 4: Handover to UTRAN 5: Handover from UTRAN 6: GSM
Text
66
Range/Unit
Arg
Description
All elements starting with HS (including channel names in HS-) relate to HSPA. Special subgroups are HS MIMO and HS UL; see general remarks on these. 0 ... 100 % 0 ... 100 % 0 ... 30 See Description Use of 16-QAM as modulation method, expressed as a percentage of time. Use of 64-QAM as modulation method, expressed as a percentage of time. The maximum value of the CQI (Channel Quality Indicator) during the latest reporting period. The definition of the CQI values is given in 3GPP 25.214, section 6A.2.
HS CQI (Median)
0 ... 30
The median CQI value during the latest reporting period. Compare HS CQI (Max).
HS CQI (Min)
0 ... 30
The minimum CQI value during the latest reporting period. Compare HS CQI (Max).
0 ... 255 ms * 2
CQI feedback cycle, controlling how often the UE transmits new CQI information on the uplink (see 3GPP 25.214, section 6A.1.2). A value of zero means that the UE shall not transmit any CQI information. CQI repetition factor, controlling how often the UE repeats CQI information on the uplink (see 3GPP 25.214, section 6A.1.2). ACK / (NACK + ACK) ratio on the HS-DSCH.
0 ... 15
0 ... 100 %
67
IE Name HS-DSCH BLER 1st HS-DSCH BLER Residual HS-DSCH BLER Residual Per Process
Arg
Description Block error rate on the HSDSCH for first transmission. Residual block error rate on the HS-DSCH (decoding unsuccessful after maximum number of retransmissions). Same as HS-DSCH BLER Residual but for each active HARQ process separately. Argument: HARQ process index.
0 ... 100 %
0 ... 16
HS-DSCH DTX Rate HS-DSCH Error Blocks 1st No Of HS-DSCH Error Blocks Residual No Of HS-DSCH Error Blocks Residual No Of Per Process
DTX rate on the HS-DSCH. Number of block errors on the HS-DSCH (first transmission). Number of residual block errors on the HS-DSCH (decoding unsuccessful after maximum number of retransmissions). Same as HS-DSCH Error Blocks Residual No Of but for each active HARQ process separately. Argument: HARQ process index.
0 ... 100
0 ... 100
0 ... 16
0 ... 16
Number of active HARQ (Hybrid Automatic Repeat Request) processes on the HS-DSCH. NACK / (NACK + ACK) ratio on the HS-DSCH.
0 ... 100 %
68
IE Name HS-DSCH New Transmission Rate Per Process HS-DSCH Post Rate
Arg 0 ... 16
Description New transmission rate on the HS-DSCH for each active HARQ process. Argument: HARQ process index.
0 ... 100 %
Rate of use of postamble indicator after TTI where data is sent, notifying the Node B of the fact that the ACK/NACK sequence ends. Rate of use of preamble indicator prior to TTI where data is sent, notifying the Node B of the fact that a sequence of ACKs/NACKs will be sent. Retransmission rate on the HSDSCH. Same as HS-DSCH Retransmission Rate but for each active HARQ process separately. Argument: HARQ process index.
0 ... 100 %
0 ... 16
HS-DSCH Retransmissions HS-DSCH Throughput (kbit/s) HS-DSCH Throughput (kbit/s) Per Process
0 ... 100
0 ... 16
Same as HS-DSCH Throughput (kbit/s) but for each active HARQ process separately. Argument: HARQ process index.
HS H-RNTI
0 ... 65535
69
Arg 1 ... 32
Description MAC-hs priority queue identity. Argument: MAC-hs priority queue index.
These IEs are populated when MIMO is in use on the downlink. Non-MIMO IEs which have a counterpart among MIMO IEs (such as the CQI elements) are not updated while MIMO is being used. However, certain other HS elements of a general nature are updated also during MIMO activity. The argument, where present, has the following significance: Arg = 1 means MIMO Type A with one transport block. Arg = 2 means MIMO Type A with two transport blocks.
Regarding the designation MIMO Type A, see 3GPP 25.214, section 6A.1.2.2. HS MIMO 16QAM Modulation Rate HS MIMO 64QAM Modulation Rate HS MIMO CQI (Max) 0 ... 100 % 1 ... 2 Use of 16-QAM as modulation method, expressed as a percentage of time. Use of 64-QAM as modulation method, expressed as a percentage of time. The maximum value of the CQI (Channel Quality Indicator) during the latest reporting period. The definition of the CQI values is given in 3GPP 25.214, section 6A.2. HS MIMO CQI (Median) 0 ... 30 1 ... 2 The median CQI value during the latest reporting period. Compare HS MIMO CQI (Max). HS MIMO CQI (Min) 0 ... 30 1 ... 2 The minimum CQI value during the latest reporting period. Compare HS MIMO CQI (Max).
0 ... 100 %
1 ... 2
1 ... 2
70
IE Name HS MIMO DSCH ACK Rate HS MIMO DSCH NACK Rate HS MIMO Multi TB Rate
Arg 1 ... 2
Description ACK / (NACK + ACK) ratio on the HS-DSCH. NACK / (NACK + ACK) ratio on the HS-DSCH. Argument = 1: Percentage of TTIs with one transport block used. Argument = 2: Percentage of TTIs with two transport blocks used.
1 ... 2
1 ... 2
0 ... 100 %
1 ... 2
Use of QPSK as modulation method, expressed as a percentage of time. 0: MIMO Type A with one transport block 1: MIMO Type A with two transport blocks Same as HS MIMO Type but in text format. Argument = 1: Percentage of TTIs with MIMO Type A CQI and one transport block used. Argument = 2: Percentage of TTIs with MIMO Type A CQI and two transport blocks used. See 3GPP 25.214, section 6A.1.2.2.
0 ... 1
1 ... 2
0 ... 100 %
Percentage of TTIs with MIMO Type B CQI. See 3GPP 25.214, section 6A.1.2.2.
71
Arg 1 ... 15
Description Distribution of channelization code usage on the HS-PDSCH for the whole of the HSPA session. This element does not take DTX into account, so that values are computed as percentages of all blocks, whether used or unused. Argument: Channelization code index.
0 ... 100 %
1 ... 15
Current distribution of channelization code usage on the HSPDSCH. This element takes DTX into account, so that values are computed as percentages of the total number of used blocks. Argument: Channelization code index.
Calculated as: (Average requested transport block size based on CQI) / (2 ms) Calculated as: (Average transport block size in TTIs where data is transferred) / (2 ms) (Only TTIs in which data is actually received are considered in the throughput calculation.)
Calculated as: (Average transport block size counting all TTIs) / (2 ms) (All TTIs, also those in which no data is received, are included in the throughput calculation.)
72
Arg 0 ... 16
Description Same as HS Phy Served Throughput (kbit/s) but for each active HARQ process separately. Argument: HARQ process index.
Use of QPSK as modulation method, expressed as a percentage of time. Channelization codes used on the HS-SCCH, arranged in ascending order. Argument: Channelization code index.
1 ... 8
HS-SCCH Channelisation Codes No Of HS-SCCH Channelisation Codes (Text) HS-SCCH Decode Success Rate
0 ... 8
Text
0 ... 100 %
Decode success rate on the HSSCCH. For the decoding to count as a success, both the first and the second parts must have been completed successfully. The scrambling code index of the HSPA serving cell. c Name of HSPA serving cell.
73
IE Name HS Session
Range/Unit 0, 1
Arg
Description Indicates whether the session is an HSDPA or HSUPA session (as opposed to an R99 session). 0: No 1: Yes
Text
Argument = Transport block size sequence number means that 0 represents the first TBS used, etc.; the argument value does not equate to the corresponding TBS index. Argument = Transport block size index means that the argument represents the TBS index with this value.
0 ... 65535
1 ... 295
Block counts for HSPA transport block sizes currently in use, accumulated over the current session. Argument: Transport block size sequence number.
0 ... 65535
1 ... 295
Block counts for HSPA transport block sizes currently in use, collected over the latest report period. Argument: Transport block size sequence number.
0 ... 65535
1 ... 295
Block counts for HSPA transport block sizes currently in use, accumulated over the current session. Argument: Transport block size index.
0 ... 65535
1 ... 295
Block counts for HSPA transport block sizes currently in use, collected over the latest report period. Argument: Transport block size index.
74
Description Transport block sizes on the HSDSCH. Argument: Transport block size sequence number.
1 ... 295
Transport block sizes on the HSDSCH. Argument: Transport block size index.
0 ... 295
These elements pertain to HSUPA (EUL) and are updated primarily when that technology is in use. However, even if only HSDPA is available in the network, uplink activity occurring in the course of running HSDPA may still cause some of the HS UL elements to be populated. 0 ... 800 Average value of serving grant (maximum allowed E-DPDCH/ E-DPCCH power ratio). Average value of serving grant index.
HS UL Average Serving Grant HS UL Average Serving Grant Index HS UL Average TBS HS UL Average TBS / TBS Max E-TFCI
0 ... 40
Average transport block size on E-DCH. Average value of: (transport block size on E-DCH) divided by (maximum transport block size on E-DCH as dictated by current E-TFCI). This is a measure of serving grant utilization. Block error rate on the E-DCH for first transmission.
HS UL BLER 1st
0 ... 100 %
75
Arg
Description Residual block error rate on the E-DCH (decoding unsuccessful after maximum number of retransmissions). Percentage of time the transmission on the E-DCH was buffer limited. Percentage of TTIs where nothing was sent on the EDPCCH/E-DPDCH. Throughput on the E-DCH.
HS UL Buffer Limited Tx Rate HS UL DTX Rate HS UL E-DCH Throughput (kbit/s) HS UL Error Blocks No Of 1st HS UL Error Blocks No Of 2nd HS UL Error Blocks No Of 3rd HS UL Error Blocks No Of 4th HS UL Error Blocks Residual No Of HS UL Happy Rate HS UL HICH ACK Rate HS UL HICH NACK Rate
Number of block errors for the first transmission on the E-DCH. Number of block errors for the second transmission on the EDCH. Number of block errors for the third transmission on the EDCH. Number of block errors for the fourth transmission on the EDCH. Number of residual block errors on the E-DCH after maximum number of retransmissions. Percentage of TTIs where the UE was happy. ACK rate on the E-HICH (HARQ Acknowledgement Indicator Channel). NACK rate on the E-HICH.
0 ... 100
0 ... 100
0 ... 100
0 ... 100
76
IE Name HS UL New Transmission Rate HS UL NonServing Cells No Of HS UL NonServing ERGCH Down No Of HS UL Number Of TTIs HS UL Power Limited Tx Rate HS UL Retransmission Rate HS UL Serving Grant Limited Tx Rate HS UL Successful EAGCH Rate (All TTIs) HS UL Successful First Tx Rate IMEI
Arg
Description Number of new transmissions on E-DPCCH/E-DPDCH divided by the number of TTIs. Number of non-serving cells in E-DCH active set. Number of times a non-serving cell in the E-DCH active set was ordered to lower its transmit power (relative grant = Down). Number of TTIs (transmission time intervals) in log report. Percentage of time the transmission was limited by the available Tx power. Number of retransmissions on E-DPCCH/E-DPDCH divided by the number of TTIs. Percentage of time the transmission was limited by the current serving grant. Percentage of TTIs where the UE received an absolute grant on the E-AGCH. Percentage of TTIs where the first transmission was successful. International Mobile Equipment Identity, the unique equipment identity of the UE.
0 ... 100
0 ... 100 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 100 %
77
Range/Unit Text
Arg 1 ... 10
Description Event criteria governing when the UE should send interfrequency measurement reports. Argument: One argument for each event criterion.
Text
1 ... 10
Names of events governing sending of inter-frequency measurement reports by the UE. The events extracted to this element are e2a, e2d, and e2f. Other inter-frequency events are not extracted. Argument: One argument for each event criterion. There may be multiple criteria for the same event.
Text
1 ... 5
Event criteria governing when the UE should send inter-RAT measurement reports. Argument: One argument for each event criterion.
Text
1 ... 5
Names of events governing sending of inter-RAT measurement reports by the UE. The only event extracted to this element is e3a. Other interRAT events are not extracted. Argument: One argument for each event criterion. There may be multiple criteria for the same event.
Intra-freq Cells
Text
78
Range/Unit Text
Arg 1 ... 10
Description Event criteria governing when the UE should send intrafrequency measurement reports. Argument: One argument for each event criterion.
Text
1 ... 10
Names of events governing sending of intra-frequency measurement reports by the UE. The events extracted to this element are e1a, e1b, e1c, and e1d. Other intra-frequency events are not extracted. Argument: One argument for each event criterion. There may be multiple criteria for the same event.
p p
Latitude recorded by positioning equipment. Latitude as text. For the presentation format, see RA UM appendix C.4. Longitude recorded by positioning equipment. Longitude as text. For the presentation format, see RA UM appendix C.4. Mobile Country Code. Contains the hexadecimal string of a Layer 3 message or mode report. Used for text-format logfile export only.
p p
MNC
0 ... 999
79
Range/Unit 1 ... 7
Arg
Description 1: No service 2: Idle mode 3: Dedicated (Connected) mode (4: Limited service mode) (5: Scan mode) (6: Packet mode) (7: Packet Idle mode) Relevant values: 1: WCDMA 2: GSM
Mode - System
1 ... 8
Text Text
1 ... 6 c
Same as Mode - System but in text format. Cell name of each monitored neighbor. Argument: Neighbor identity.
34 ... 0 dB
1 ... 6
1 ... 6
CPICH received signal code power of each monitored neighbor. Argument: Neighbor identity.
Mon Neigh CPICH Tx Power Mon Neigh No Of Members Mon Neigh Pathloss
31 ... 50 dBm
1 ... 6
1 ... 6
Number of monitored neighbors. Pathloss of each monitored neighbor. Calculated as Primary CPICH Tx Power CPICH RSCP. Argument: Neighbor identity.
80
Arg 1 ... 6
0 ... 16383 (frequency band dependent) Text: B, C, or a combination of these letters (or empty string)
1 ... 6
Indicates whether the UE behavior has been changed from the default. Empty string: No modification of UE behavior B: Modification of UE behavior in network (information elements BLER Target Control, RAT Control) C: Modification of UE reselection behavior: (information elements Cell Barred Control, Sector Control) Combinations of these letters may appear.
0 ... 800
ns
Network scanning: The number of UARFCNs scanned. Network scanning: Scrambling code detected on each UARFCN scanned. Argument: Position in list of scanned UARFCNs.
0 ... 511
1 ... 800
ns
1 ... 800
ns
81
Range/Unit 0 ... 10 dB
Arg 0 ... 10 dB
* pi
Description Pilot scanning (DC UM section 10.2): Estimated ratio between polluting signal power and desired signal power on a CPICH control channel, based on the assumption that there is only one possible member in the active set. Applies to the first UMTS frequency scanned (lowest UARFCN). Argument: Power threshold (in dB) relative to the power of the strongest scrambling code; used to identify possible active set members. See DC UM section 10.2.7 for a full description.
0 ... 10 dB
0 ... 10 dB
pi
As Other/Own, Max 1 SC except that the active set is assumed to have at most two possible members. Applies to the first UMTS frequency scanned. See DC UM section 10.2.7 for a full description.
0 ... 10 dB
0 ... 10 dB
pi
As Other/Own, Max 1 SC except that the active set is assumed to have at most three possible members. Applies to the first UMTS frequency scanned. See DC UM section 10.2.7 for a full description.
82
Range/Unit 0 ... 10 dB
Arg 0 ... 10 dB
* pi
Description As Other/Own, Max 1 SC except that the active set is assumed to have at most four possible members. Applies to the first UMTS frequency scanned. See DC UM section 10.2.7 for a full description.
Other/Own 2nd (etc.) elements PDP IEs: General remark PDP Access Point Name PDP Address PDP Contexts Active PDP Delay Class PDP LLC SAPI PDP Mean Throughput PDP NSAPI PDP Peak Throughput PDP Precedence Class
0 ... 10 dB
0 ... 10 dB
pi
Same as Other/Own, ... but for the second (etc.) UMTS frequency scanned.
Host name or network address for each active PDP context. User address (IPv4/IPv6). Number of active PDP contexts. Delay class as defined by subscription. LLC Service Access Point Identifier. Mean throughput as defined by subscription. Network SAPI (Service Access Point Identifier). Peak throughput as defined by subscription. Precedence class as defined by subscription.
83
IE Name PDP Radio Priority PDP Reliability Class PESQ elements Poss No of AS Members
Description Radio priority level as defined by subscription. Reliability class as defined by subscription.
See the description (cellular technology independent) under GSM, page 38. 0 ... 10 0 ... 10 dB pi Pilot scanning: The estimated number of possible members in the active set. Applies to the first UMTS frequency scanned (lowest UARFCN). Argument: Power threshold (in dB) relative to the power of the strongest scrambling code. See DC UM section 10.2.7 for a full description.
0 ... 10
0 ... 10 dB
pi
Same as Poss No of AS Members but for the second (etc.) UMTS frequency scanned. Inner loop power control indication on downlink. Based on the recent history of power control decisions: The value 1 means that the power has been adjusted predominantly downward. The value 0 means that the upward and downward power adjustments have canceled out exactly. The value +1 means that the power has been adjusted predominantly upward.
1, 0, 1
84
Range/Unit 1, 0, 1
Arg
Description Inner loop power control indication on uplink. Works the same way as Power Control Indication DL, which see. Transmit power of first RACH preamble in dBm. Maximum number of preambles in one preamble ramping cycle. Transmit power of last RACH preamble in dBm. Number of preambles used in this preamble ramping cycle. Use of Lock to RAT function in UE. 0: Lock to RAT disabled 1: Locked to GSM 900/1800 2: Locked to GSM 850/1900 3: Locked to WCDMA
RACH Initial TX RACH Max Preambles RACH Message TX RACH Transmitted Preambles RAT Control
0 ... 3
Text
Use of Lock to RAT function in UE. Blank when no lock is engaged; Active when lock to RAT has been activated. The scrambling code of the uplink Dedicated Physical Channel. Radio Link Control (Acknowledged Mode): Type of downlink logical channel, e.g. DCCH. Argument: Logical channel index.
0 ... 108
Text
1 ... 4
85
Arg 1 ... 4
Description Radio Link Control (Acknowledged Mode, downlink): PDU retransmission percentage. Calculated as:
no. of NACKed PDUs 100 -------------------------------------------------------------------------total no. of PDUs
Argument: Logical channel index. RLC AM DL PDU Thr 0 ... 80000 kbit/s 1 ... 4 Radio Link Control PDU throughput (Acknowledged Mode, downlink), counting both control PDUs and AM PDUs. Since the PDU throughput includes RLC headers, it will be slightly higher than the SDU throughput where such headers are absent. Argument: Logical channel index. RLC AM DL SDU Thr 0 ... 80000 kbit/s 1 ... 4 Radio Link Control SDU throughput (Acknowledged Mode, downlink). Argument: Logical channel index. RLC AM UL Log Ch Type Text 1 ... 4 Radio Link Control (Acknowledged Mode): Type of uplink logical channel, e.g. DCCH. Argument: Logical channel index.
86
Arg 1 ... 4
Description Radio Link Control (Acknowledged Mode, uplink): PDU retransmission percentage. Calculated as:
no. of NACKed PDUs 100 -------------------------------------------------------------------------total no. of PDUs
Argument: Logical channel index. RLC AM UL PDU Thr 0 ... 80000 kbit/s 1 ... 4 Radio Link Control PDU throughput (Acknowledged Mode, uplink), counting both control PDUs and AM PDUs. Since the PDU throughput includes RLC headers, it will be slightly higher than the SDU throughput where such headers are absent. Argument: Logical channel index. RLC AM UL SDU Thr 0 ... 80000 kbit/s 1 ... 4 Radio Link Control SDU throughput (Acknowledged Mode, uplink). Argument: Logical channel index. RLC DL Entity Data Mode Text: TM, UM, or AM 1 ... 32 Downlink RLC entity data mode: Transparent Mode, Unacknowledged Mode, or Acknowledged Mode. Argument: RLC entity. RLC DL Throughput RLC No Of Entities 0 ... 80000 kbit/s 0 ... 32 1 ... 32 Total RLC downlink throughput. Argument: RLC entity. Total number of RLC entities on uplink and downlink.
87
Arg 1 ... 32
Description Uplink RLC entity data mode: Transparent Mode, Unacknowledged Mode, or Acknowledged Mode. Argument: RLC entity.
RLC UL Throughput RLC/Trsp DL Throughput (Best) RLC/Trsp UL Throughput (Best) RRC Connection Reject Cause
1 ... 32
Highest downlink throughput for all RLC entities/transport channels. Highest uplink throughput for all RLC entities/transport channels. Cause for rejection of RRC connection establishment request. 0: Congestion 1: Unspecified See 3GPP 25.331, section 10.3.3.31.
0 ... 16 s
The time the UE has to wait before repeating the rejected RRC procedure. See 3GPP 25.331, section 10.3.3.50.
88
Range/Unit 0 ... 5
Arg
Description State of RRC protocol: 0: No service 1: Idle mode 2: Connected_Cell_FACH 3: Connected_Cell_DCH 4: Connected_Cell_PCH 5: Connected_URA_PCH The state is set to idle when the UE registers, and the information element is then updated each time the state changes. See 3GPP 25.331, chapter 7.
1 ... 38
Same as RRC State but in text format. Serving/Active Set + Neighbors window: Cell identity of each cell listed. Argument: Indicates the row in the window. In Cell_DCH mode, the active set is on top (max 4 rows), whereas in other modes the serving cell is found on row 1. In either case the neighbors follow directly beneath.
0 ... 216 1
1 ... 38
Cell Identity part of SAN Cell Id: bits 12 through 27 (in decimal). Argument: See SAN Cell Id.
1 ... 38
Cell Identity part of SAN Cell Id: bits 12 through 27 in hexadecimal. Argument: See SAN Cell Id.
0 ... 212 1
1 ... 38
RNC part of SAN Cell Id: bits 0 through 11 (in decimal). Argument: See SAN Cell Id.
89
Arg 1 ... 38
Description RNC part of SAN Cell Id: bits 0 through 11 in hexadecimal. Argument: See SAN Cell Id.
1 ... 38
Serving/Active Set + Neighbors window: Name of each cell listed. Argument: Window row.
1 ... 4
1 ... 38
Serving/Active Set + Neighbors window: Type of cell for each cell listed. 1: Serving cell 2: Active set member 3: Monitored neighbor 4: Detected neighbor Argument: Window row.
Text
1 ... 38
Same as SAN Cell Type but with text strings indicating the type of cell: SC: Serving cell AS: Active set member MN: Monitored neighbor DN: Detected neighbor Argument: Window row.
34 ... 0 dB
1 ... 38
Serving/Active Set + Neighbors window: CPICH Ec/No for each cell listed. Argument: Window row.
1 ... 38
Serving/Active Set + Neighbors window: CPICH RSCP for each cell listed. Argument: Window row.
90
Arg 1 ... 38
Description Serving/Active Set + Neighbors window: Primary CPICH transmit power for each cell listed. Argument: Window row.
0, 1
1 ... 38
Serving/Active Set + Neighbors window: Cell type for each cell in HSPA active set. 0: Non-serving cell 1: Serving cell
Text 0 ... 38
1 ... 38
Same as SAN HS Cell Type but in text format: N-SC or SC. Serving/Active Set + Neighbors window: Total number of cells listed. Serving/Active Set + Neighbors window: Pathloss for each cell listed. Calculated as Primary CPICH Tx Power CPICH RSCP. Argument: Window row.
30 ... 165 dB
1 ... 38
SAN SC
0 ... 511
1 ... 38
Serving/Active Set + Neighbors window: Scrambling code for each cell listed. Argument: Window row.
SAN UARFCN DL
1 ... 38
Serving/Active Set + Neighbors window: Downlink UARFCN for each cell listed. Argument: Window row.
SAN URA Id
1 ... 38
Serving/Active Set + Neighbors window: URA identity of each cell listed. Argument: Window row.
91
Range/Unit
Arg
Description
These elements combine scrambling codes from all scanned UMTS frequencies, sorted by descending Aggr Ec/Io. The sorting order of the Best elements is not affected by the settings in the General window (see DC UM section 10.2.11.1). Regarding pilot scanning in general, see DC UM section 10.2. Argument (where present): 1 is the scrambling code with the highest Aggr Ec/Io, etc.
10 ... 21 dB
1 ... 512
pi
Pilot scanning: The aggregate code power of the scrambling code (Eb, energy per bit) relative to the total signal power in the channel (Io). Pilot scanning: The aggregate code power (energy per chip) of each scanned scrambling code. The aggregate code power is a measure of the total signal power (distributed around the main peak due to multipath propagation) that is above the PN threshold (see DC UM section 10.2.2). Pilot scanning: The aggregate code power of the scrambling code (Ec, energy per chip) relative to the total signal power in the channel (Io). Pilot scanning: The difference between the aggregate code power and peak code power.
1 ... 512
pi
30 ... 0 dB
1 ... 512
pi
0 ... 90 dB
1 ... 512
pi
92
Range/Unit Text
* pi c p
Description Pilot scanning: Deduced name of the cell that uses each scanned scrambling code. The algorithm determining the cell name takes as input the SC number, the UARFCN, and the position reported. It searches the cell file for cells with matching SC number and UARFCN within a 50 km radius. If multiple matches are found, the cell closest to the position is selected. If no positioning data is available, the information element will still be presented, but the cell names may then of course be wrong. The algorithm in this case simply picks the first cell in the cell file with matching SC number and UARFCN. Invalid if no cell file is loaded.
1 ... 3
1 ... 512
pi c p
Pilot scanning: Categorization of the cells that use the scanned scrambling codes. 1: The cell with the strongest Aggr Ec. 2: All neighbors of the 1 cell, as indicated by the cell file. 3: All other cells. In the Sc Best element, this categorization is applied for each UMTS frequency, so there will be one 1 with associated 2s for each frequency. Invalid if no cell file is loaded.
93
* pi
Description Pilot scanning: Time in chips between the first and last Ec/Io peak that is above the PN threshold (see DC UM section 10.2.2). This is a measure of the signal spreading due to multipath propagation. Pilot scanning: The total signal power in the channel. Pilot scanning: The number of scrambling codes scanned. Pilot scanning: The peak code power of each scanned scrambling code (Eb, energy per bit) relative to the total signal power in the channel (Io), i.e. the difference between them in dB. Pilot scanning: The peak code power of each scanned scrambling code (Ec, energy per chip) in dBm. Pilot scanning: The peak code power of each scanned scrambling code (Ec, energy per chip) relative to the total signal power in the channel (Io), i.e. the difference between them in dB. The peak code power of each scanned scrambling code on the primary synchronization channel (P-SCH).
1 ... 512
pi pi pi
1 ... 512
pi
30 ... 0 dB
1 ... 512
pi
1 ... 512
pi
94
Range/Unit 30 ... 0 dB
* pi
Description The peak code power (Ec) of each scanned scrambling code on the primary synchronization channel (P-SCH), relative to the total signal power in the channel (Io). Pilot scanning: The number of Ec/Io peaks (multipath components) that are above the PN threshold. Pilot scanning: The number of each scanned scrambling code. Pilot scanning: The number of the group to which each scanned scrambling code belongs. Pilot scanning: Received SIR (in dB) for scanned scrambling codes. The peak code power of each scanned scrambling code on the secondary synchronization channel (S-SCH). The peak code power (Ec) of each scanned scrambling code on the secondary synchronization channel (S-SCH), relative to the total signal power in the channel (Io). Pilot scanning: The time offset of the radio frame (10 ms = 38,400 chips) for each scanned scrambling code. Pilot scanning: Equal to (Sc Best Time Offset mod 2560) + 1.
0 ... 51
1 ... 512
pi
pi pi
Sc Best SIR (dB) Sc Best S-SCH Ec (dBm) Sc Best S-SCH Ec/Io (dB)
1 ... 512
pi
1 ... 512
pi
30 ... 0 dB
1 ... 512
pi
1 ... 512
pi
1 ... 2560
1 ... 512
pi
95
Arg
* pi
pi
Pilot scanning: Interference on uplink, extracted from SIB type 7. Pilot scanning: Neighbor list for the first scrambling code on the first (second, third, etc.) scanned UMTS frequency. Obtained from SIB. What scrambling code is the first depends on the sorting order set in the General window: see DC UM section 10.2.11.1. Given as a comma-separated string of scrambling codes, e.g. 1, 3, 5. No Sc Best version is provided for these elements, since that would be pointless.
pi
Same as Sc Best elements except that only the first (second, third, etc.) scanned UMTS frequency is considered. Note: More IEs are provided for frequencies 14 than for frequencies 512. Argument: The sorting order depends on the General window setting: see DC UM section 10.2.11.1.
96
Range/Unit 24 ... 0 dB
* ts
Description SCH timeslot scanning (DC UM section 10.3): Power in each segment (1, 2, 4, or 8 chips depending on setup) of the scanned timeslot. Argument: Index of timeslot segment (not chip index). If Every 2 has been chosen, the argument range is 1 ... 2560/2, i.e. 1 ... 1280; for Every 4, the range is 1 ... 640; for Every 8, the range is 1 ... 320.
SCH TS Sc No Of Segm
0 ... 2560
ts
SCH timeslot scanning: Number of scanned timeslot segments (each with length 1, 2, 4, or 8 chips depending on setup). SCH timeslot scanning: Position of each timeslot segment scanned, expressed as a chip index. The first chip has number 1. Argument: Index of timeslot segment (not chip index). If Every 2 has been chosen, the argument range is 1 ... 2560/2, i.e. 1 ... 1280; for Every 4, the range is 1 ... 640; for Every 8, the range is 1 ... 320.
SCH TS Sc Segm
1 ... 2560
ts
ts
SCH timeslot scanning: The time separation in chips between the strongest peak and the second strongest. SCH timeslot scanning: The time separation in chips between the second strongest peak and the third strongest.
ts
97
Arg
* ts
Sector Control
0, 1
Use of Lock to Sector/Cell Selection function in UE in idle mode: 0: Lock to Sector disabled 1: Lock to Sector enabled See DC UM sections 15.2.3.15, 15.3.2.1, 15.4.1.3, 15.4.2.4.
Sector Control (Text) Serving IEs: General remark Serving Cell Id Serving Cell Id (CI Part) Serving Cell Id (CI Part Hex) Serving Cell Id (RNC Part) Serving Cell Id (RNC Part Hex) Serving Cell LAC Serving Cell LAC (Hex)
Text
Cell identity of the serving cell. Cell Identity part of Serving Cell Id: bits 12 through 27 (in decimal). Cell Identity part of Serving Cell Id: bits 12 through 27 in hexadecimal. RNC part of Serving Cell Id: bits 0 through 11 (in decimal). RNC part of Serving Cell Id: bits 0 through 11 in hexadecimal. LAC of serving cell. LAC of serving cell in hexadecimal format.
Text: 0000 ... FFFF 0 ... 212 1 Text: 000 ... FFF 0 ... 65535 Text: 0000 ... FFFF
98
IE Name Serving Cell Name Serving Cell RAC Serving Cell RAC (Hex) Serving CPICH Ec/No Serving CPICH RSCP Serving CPICH Tx Power Serving Pathloss Serving SC
Range/Unit Text 0 ... 255 Text: 00 ... FF 34 ... 0 dB 140 ... 15 dBm 31 ... 50 dBm 30 ... 165 dB 0 ... 511
Arg
* c
Description Name of the serving cell. RAC of serving cell. RAC of serving cell in hexadecimal format. CPICH Ec/No of the serving cell. CPICH received signal code power of the serving cell. CPICH transmit power of the serving cell. Pathloss of the serving cell. Calculated as Primary CPICH Tx Power CPICH RSCP. Scrambling code of the serving cell in idle, Cell_FACH, Cell_PCH, and URA_PCH mode. Downlink UARFCN of the serving cell in idle, Cell_FACH, Cell_PCH, and URA_PCH mode. URA identity of the serving cell. Spreading factor on downlink. Spreading factor on uplink.
Serving UARFCN DL
0 ... 16383 (frequency band dependent) 0 ... 228 1 1 ... 512 1 ... 512
Serving URA Id SF DL SF UL
99
Range/Unit 0 ... 50
Description Number of radio link events (both failures and successes) over the last arg seconds, where arg is the value of the argument. Regarding the events, see section 7.2. Argument: See above. Argument = 0 means that the events are counted from the beginning of the logfile.
0 ... 100 %
Soft handover success rate. Calculated as: (# add + # rem + # repl) / # all where add = Radio Link Addition events rem = Radio Link Removal events repl = Radio Link Replacement events all = All radio link events, including failures Regarding the events, see section 7.2.
100
Arg
* c
Description A measure of the amount of softer handover. Calculated as: # softer / (# softer + # soft) where softer = Radio link event indicating success occurs while in softer handover (and with more than one member in active set) soft = Radio link event indicating success occurs while in soft handover (and with more than one member in active set) A radio link event is one of Radio Link Addition, Radio Link Removal, and Radio Link Replacement. About the events, see section 7.2. Requires that a cell file has been loaded (otherwise the element is invalid).
SHO State
0 ... 2
Soft handover state. 0: Unknown (no cell data loaded) 1: Soft handover 2: Softer handover Requires that a cell file has been loaded (otherwise the value will always be = 0). Invalid when AS No Of Members < 2.
101
Range/Unit Text
Arg
* c
Description Soft handover state as plain text: Soft, Softer, or Unknown. See SHO State. Requires that a cell file has been loaded (otherwise the value will always be Unknown). Invalid when AS No Of Members < 2.
SIR
20 ... 30 dB 20 ... 30 dB
Signal-to-interference ratio, measured on DPCCH. See 3GPP 25.215, section 5.2.2. SIR target governing SIR.
These elements are obtained from spectrum analysis. The argument, where present, is simply a sequence number pointing to scanned frequencies as indicated by the Spectr Ana Sc DL Freq or Spectr Ana Sc UL Freq element.
1930 ... 1990 or 2110 ... 2170 MHz
1 ... 2560
ss
Spectrum analysis: Scanned frequencies on downlink in ascending order. Spectrum analysis: The number of downlink frequencies swept by the scan. Spectrum analysis: RSSI of downlink frequencies scanned. Spectrum analysis: Scanned frequencies on uplink in ascending order. Spectrum analysis: The number of uplink frequencies swept by the scan.
Spectr Ana Sc DL No of Freq Spectr Ana Sc DL RSSI (dBm) Spectr Ana Sc UL Freq
0 ... 2560
ss
ss
ss
0 ... 2560
ss
102
* ss
Description Spectrum analysis: RSSI of uplink frequencies scanned. AQM: The length of time it takes for the speech to travel from the Call Generator to the MTU and back to the Call Generator again. This element only appears in merged logfiles (see RA UM section 17.2).
p p
Speed in km/h. Speed in mph. Speech Quality Index for WCDMA. The range is different depending on the AMR speech codec mode. The maximum SQI values are as follows: 12.2 kbit/s: 30 dBQ 10.2 kbit/s: 28 dBQ 7.95 kbit/s: 28 dBQ 7.40 kbit/s: 27 dBQ 6.70 kbit/s: 27 dBQ 5.90 kbit/s: 24 dBQ 5.15 kbit/s: 21 dBQ 4.75 kbit/s: 19 dBQ
1 ... 6 c
SQI expressed on the MOS scale. See DC UM chapter 28. Cell names of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
103
Range/Unit 34 ... 0 dB
Arg 1 ... 6
Description CPICH Ec/No of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
1 ... 6
CPICH RSCP of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
Str Neigh SC
0 ... 511
1 ... 6
Scrambling codes of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
3, 4
1 ... 6
Types of neighbors (monitored as well as detected) sorted by signal strength in descending order. The types are: 3: Monitored neighbor 4: Detected neighbor Argument: 1 is the strongest neighbor, etc.
1 ... 6
CPICH UARFCNs of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
Time (Text)
Text
104
Arg
Description Block error rate on the worst downlink transport channel (DCH only) in percent. Block error rate on each downlink transport channel (DCH only), converted to logarithmic value. Regarding the conversion, see 3GPP 25.331, section 10.3.5.10. Argument: Transport channel index. Note: Nokia UEs do not deliver separate values for each transport channel, but only an average over all of them (arg = 1).
1 ... 32
0 ... 100 %
1 ... 32
Block error rate on each downlink transport channel (DCH only) in percent. See 3GPP 25.215, section 5.1.6. Compare Trsp Ch BLER, DL (Log). Argument: Transport channel index.
0 ... 100 %
1 ... 32
Block error rate target for each downlink transport channel (DCH only) in percent. Argument: Transport channel index.
Trsp Ch Id DL
1 ... 32
1 ... 32
Identity of each downlink transport channel. The channel type is indicated by the element Trsp Ch Type DL. Argument: Transport channel index.
Trsp Ch No Of DL
0 ... 32
105
Arg 1 ... 32
Description Number of uplink transport channels. Number of erroneous blocks on each transport channel. (The number of reports over which this is summed varies between phones.) Compare Trsp Ch BLER, DL (Log). Argument: Transport channel index.
0 ... 4095
1 ... 32
Number of blocks received on each transport channel. (The number of reports over which this is summed varies between phones.) Argument: Transport channel index.
1 ... 32
Total downlink throughput on all transport channels. Argument: Transport channel index.
1 ... 32
Total uplink throughput on all transport channels. Argument: Transport channel index.
106
Range/Unit Text
Arg 1 ... 32
Description Downlink transport channel type: DCH or FACH. Argument: Transport channel index.
Trsp Ch Type UL
Text
1 ... 32
Uplink transport channel type: DCH or RACH. Argument: Transport channel index.
UE Initial Transmit Power UE Tx Power UL Interference Serving UTRA Carrier RSSI VTQI
60 ... 44 dBm 60 ... 44 dBm 110 ... 70 dBm 130 ... 20 dBm 1 ... 5 MOS
UE transmit power in dBm. Valid only in connected mode. Interference on uplink, extracted from SIB type 7. Total energy measured by the UE within the downlink bandwidth. Video Telephony Quality Index; see DC UM chapter 30.
107
3.3.
All elements in this category are supported by both DRT and PCTel scanners unless otherwise noted in section 5.4. The argument, where present, always points to an LTE cell unless otherwise stated.
IE Name Altitude (ft) Range/Unit 1312 ... 29028 ft 400 ... 8848 m Arg Description Height above sea level in feet. Reported by positioning equipment. Height above sea level in meters. Reported by positioning equipment.
Altitude (m)
EPower IEs: General remark EPower Ana Sc DL Freq (kHz) EPower Ana Sc DL No Of Freq EPower Ana Sc DL RSSI (dBm) Firmware Version Hardware Hardware ID Heading (deg)
These elements originate from enhanced power scanning. Argument: Points to a frequency as specified by the EPower Ana Sc DL Freq (kHz) element. 0 ... 6 106 kHz 0 ... 2560 1 ... 2559 List of frequencies scanned.
140 ... 25 dBm Text Text Text 0 ... 360 degrees 90 ... 90 degrees
1 ... 2559
Version number of device firmware. Scanner model. Hardware identification string. Direction of travel measured in degrees clockwise from north. Reported by positioning equipment. Latitude recorded by positioning equipment.
Latitude
108
IE Name Latitude (Text) Longitude Longitude (Text) Mode Mode (Num) Mode - System Mode - System (Text) Sc 1st IEs: General remark
Range/Unit Text 180 ... 180 degrees Text Text 1 ... 7 1 ... 8 Text
Arg
Description Latitude as text. For the presentation format, see RA UM appendix C.4. Longitude recorded by positioning equipment. Longitude as text. For the presentation format, see RA UM appendix C.4. Not used. Not used. Not used. Not used.
These elements derive from LTE Signal scanning. The ordinal 1st means that these IEs pertain to the first EARFCN scanned. Argument: Refers to an LTE cell. The sorting order depends on the setting in the General window: see DC UM section 11.2.5.1.
Sc 1st BCH RSSI (dBm) Sc 1st Cell Identity Sc 1st CFO (Hz)
140 ... 25 dBm 0 ... 503 10000 ... 10000 Hz 0 ... 5379 0 ... 504 140 ... 25 dBm 40 ... 60 dB
0 ... 504
BCH RSSI for each cell scanned. Obtained from DRT only.
Cell Identity (equal to 3 * PCIG + PCI) for each cell scanned. Center Frequency Offset of each cell scanned. Obtained from DRT only.
Sc 1st EARFCN Sc 1st No Of Cell Identities Sc 1st P-SCH RP (dBm) Sc 1st RS CINR (dB)
EARFCN of each cell scanned. See 3GPP 36.101, section 5.4.4. Total number of detected Cell Identities. P-SCH received power for each cell scanned. Reference Signal CINR for each cell scanned.
109
IE Name Sc 1st RSRP (dBm) Sc 1st RSRP Tx1 (dBm) Sc 1st RSRP Tx2 (dBm) Sc 1st RSRP Tx3 (dBm) Sc 1st RSRP Tx4 (dBm) Sc 1st RSRQ (dB) Sc 1st RSRQ Tx1 (dB) Sc 1st RSRQ Tx2 (dB) Sc 1st RSRQ Tx3 (dB) Sc 1st RSRQ Tx4 (dB) Sc 1st SCH CINR (dB)
Range/Unit 140 ... 25 dBm 140 ... 25 dBm 140 ... 25 dBm 140 ... 25 dBm 140 ... 25 dBm 40 ... 40 dB 40 ... 40 dB 40 ... 40 dB 40 ... 40 dB 40 ... 40 dB 40 ... 60 dB
Arg 0 ... 504 0 ... 504 0 ... 504 0 ... 504 0 ... 504 0 ... 504
Description Reference Signal RSSI (sum total over all Tx ports) for each cell scanned. Reference Signal RSSI for Tx port 1 for each cell scanned. Reference Signal RSSI for Tx port 2 for each cell scanned. Reference Signal RSSI for Tx port 3 for each cell scanned. Reference Signal RSSI for Tx port 4 for each cell scanned. Reference Signal Received Quality (sum total over all Tx ports) for each cell scanned. Reference Signal Received Quality for Tx port 1 for each cell scanned. Reference Signal Received Quality for Tx port 2 for each cell scanned. Reference Signal Received Quality for Tx port 3 for each cell scanned. Reference Signal Received Quality for Tx port 4 for each cell scanned. DRT: Synch Channel (not specified as P-SCH or S-SCH) CINR for each cell scanned. PCTel: P-SCH CINR for each cell scanned.
0 ... 504 0 ... 504 0 ... 504 0 ... 504 0 ... 504
40 ... 40 dB
0 ... 504
DRT: Synch Channel (not specified as P-SCH or S-SCH) Received Quality for each cell scanned. PCTel: P-SCH Received Quality for each cell scanned.
0 ... 504
110
Description Time offset (in s) from the beginning of the current frame, adjusted so that a frame begins at the GPS one-second tick epoch. In other words, the offset is the time from the last one-second tick modulo 10,000 s (= 10 ms).
These elements are analogous to Sc 1st but pertain to the second (etc.) EARFCN scanned. Note: More IEs are provided for frequencies 14 than for frequencies 512. These elements combine cells from all scanned EARFCNs, sorted by descending RSRQ (Es/Io). The sorting order of the Best elements is not affected by the settings in the General window (see DC UM section 11.2.5.1). Note: Fewer IEs are provided than for any individual EARFCNs.
These elements derive from RSSI scanning. The argument, where present, is a sequence number pointing to scanned frequencies as specified by the Sc RSSI Frequency (kHz) element, unless otherwise indicated. Text Text 0 ... 1000 0 ... 5379 0 ... 6 106 kHz 140 ... 25 dBm 140 ... 25 dBm 1 ... 1000 1 ... 1000 1 ... 1000 1 ... 1000 1 ... 1000 0 ... 5379 Band to which each scanned cell belongs. Bandwidth used for each scanned cell. Number of cells scanned. EARFCN of each scanned cell. Frequency of each cell scanned.
Sc RSSI Band Sc RSSI Bandwidth Sc RSSI Count Sc RSSI EARFCN Sc RSSI Frequency (kHz) Sc RSSI (dBm) Sc RSSI (dBm) [EARFCN]
RSSI for each scanned cell. RSSI for each scanned cell. Argument: EARFCN.
111
Range/Unit
Arg
Description
These elements are populated by spectrum analysis scanning. The same elements are used for both uplink and downlink bands. The argument, where present, is a sequence number pointing to scanned frequencies as indicated by the Spectr Ana Sc Freq (kHz) element. 0 ... 6 106 kHz 0 ... 3001 140 ... 25 dBm 0 ... 250 km/h 0 ... 160 mph 1 ... 3001 1 ... 3001 Scanned frequencies in ascending order. The number of frequencies swept by the scan. RSSI of frequencies scanned. Speed in km/h. Speed in mph.
Spectr Ana Sc Freq (kHz) Spectr Ana Sc No Of Freq Spectr Ana Sc RSSI (dBm) Speed (km/h) Speed (mph) Strongest Sc RSSI IEs: General remark Strongest Sc RSSI (dBm) Strongest Sc RSSI Band Strongest Sc RSSI EARFCN Strongest Sc RSSI Frequency (kHz) Time
These elements contain RSSI scan data. Argument: The frequencies are sorted by decreasing RSSI.
Received signal strength. Scanned frequency band. Scanned EARFCN. Scanned frequency.
Text
112
Arg
113
3.4.
This category includes a large number of elements that are not TDD-specific, as well as many that also make an appearance in the GSM and/or WCDMA categories. The latter elements relate to parts of the 3GPP specifications that TD-SCDMA shares with GSM and/or WCDMA. Note that dual mode TD-SCDMA/GSM terminals also populate elements in the GSM category; see section 5.2 for specifics. Information Element Table
IE Name Altitude (ft) Range/Unit 1312 ... 29028 ft 400 ... 8848 m Text See section 3.1 under ARFCN BCCH Text Arg Description Height above sea level in feet. Reported by positioning equipment. Height above sea level in meters. Reported by positioning equipment. 1 ... 16 Version number of device firmware. ARFCNs of measured GSM neighbors. Argument: 1 gives the neighbor with the highest signal strength, etc. 1 ... 16 Base Station Identity Codes (in text format) of measured GSM neighbors. Argument: See GSM Neighbor ARFCN. GSM Neighbor RxLev (dBm) 110 ... 47 dBm 1 ... 16 RxLev of measured GSM neighbors. Argument: See GSM Neighbor ARFCN. Device model. Direction of travel measured in degrees clockwise from north.
Altitude (m)
Hardware Heading
114
Arg
Description Use of 16-QAM as modulation method, expressed as a percentage of time. The maximum value of the CQI (Channel Quality Indicator) during the latest reporting period. The definition of the CQI values is given in 3GPP 25.214, section 6A.2.
HS CQI (Min)
0 ... 30
The minimum CQI value during the latest reporting period. Compare HS CQI (Max).
HS MAC PDU Receive Rate (kbit/s) HS QPSK Modulation Rate HS Transport Block Count (Accu)
MAC-hs PDU receive rate expressed in kbit/s. Use of QPSK as modulation method, expressed as a percentage of time. Block counts for HSPA transport block sizes currently in use, accumulated over the current session. Argument: 1 represents the first TBS used (not TBS 1), etc.
1 ... 254
0 ... 65535
1 ... 254
Block counts for HSPA transport block sizes currently in use, collected over the latest report period. Argument: 1 represents the first TBS used (not TBS 1), etc.
1 ... 254
Transport block sizes on the HSDSCH. Argument: 1 represents the first TBS used (not TBS 1), etc.
0 ... 254
115
IE Name HS-DSCH ACK Rate HS-DSCH BLER HS-DSCH DTX Rate HS-DSCH NACK Rate HS-DSCH Retransmission Rate HS-PDSCH Number Of Codes IMEI
Range/Unit 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 16
Arg
Description ACK / (NACK + ACK) ratio on the HSDSCH. Block error rate on the HS-DSCH for first transmission. DTX rate on the HS-DSCH. NACK / (NACK + ACK) ratio on the HS-DSCH. Retransmission rate on the HS-DSCH.
Number of channelization codes used on the HS-DPSCH, averaged over the latest reporting period. International Mobile Equipment Identity, the unique equipment identity of the phone. Latitude recorded by positioning equipment. Latitude as text. For the presentation format, see RA UM appendix C.4. Longitude recorded by positioning equipment. Longitude as text. For the presentation format, see RA UM appendix C.4. Same as Mode (Num) but in text format. Relevant values: 2: Idle mode 3: Dedicated mode
Text
90 ... 90 degrees Text 180 ... 180 degrees Text Text 1 ... 7
116
Range/Unit 1 ... 8
Arg
Mode - System (Text) Neighbor IEs: General remark Neighbor Carrier RSSI Neighbor CPI Neighbor PCCPCH Ec/No Neighbor PCCPCH RSCP Neighbor Pathloss Neighbor UARFCN
Text
Argument: The elements are sorted by descending RSCP. Argument 1 thus points to the strongest neighbor, etc. 131 ... 25 dBm 0 ... 127 30 ... 0 dB 116 ... 25 dBm 46 ... 158 dB 0 ... 16383 (frequency band dependent) 0 ... 2500 kbit/s 1 ... 32 RLC downlink throughput for each data bearer. Argument: RLC entity. 0 ... 1000 kbit/s 1 ... 32 RLC uplink throughput for each data bearer. Argument: RLC entity. Text Same as RRC State (Num) but in text format. 1 ... 32 1 ... 32 1 ... 32 1 ... 32 1 ... 32 1 ... 32 Carrier RSSI for each neighbor. Cell Parameter Identity for each neighbor. P-CCPCH Ec/No for each neighbor. P-CCPCH received signal code power for each neighbor. Pathloss for each neighbor. Primary UARFCN of each neighbor.
117
Range/Unit 0 ... 5
Arg
Description State of RRC protocol: 0: No service 1: Idle mode 2: Connected_Cell_FACH 3: Connected_Cell_DCH 4: Connected_Cell_PCH 5: Connected_URA_PCH The state is set to idle when the UE registers, and the information element is then updated each time the state changes. See 3GPP 25.331, chapter 7.
Serving C/I
30 ... 60 dB
C/I of serving cell. Calculated as Serving P-CCPCH RSCP Timeslot ISCP (dBm) for timeslot 0 (the timeslot always used by the P-CCPCH). Valid only if Serving Current UARFCN = Serving Primary UARFCN.
131 ... 25 dBm 0 ... 228 1 Text: 0000000 ... FFFFFFF 0 ... 65535 Text: 0000 ... FFFF 0 ... 127 0 ... 16383 (frequency band dependent)
Carrier RSSI for serving cell. Cell identity of serving cell in decimal. Cell identity of serving cell in hexadecimal.
Serving Cell LAC Serving Cell LAC (Hex) Serving CPI Serving Current UARFCN
LAC of serving cell. LAC of serving cell in hexadecimal format. Cell Parameter Identity of serving cell. UARFCN currently used by the serving cell: either the Primary UARFCN or a different UARFCN (the latter in dedicated mode only).
118
IE Name Serving DRX Coefficient Serving Max Allowed UL TxPower Serving MCC Serving MNC Serving PCCPCH Ec/No Serving PCCPCH RSCP Serving PCCPCH SIR Serving Pathloss Serving Primary UARFCN
Range/Unit 3 ... 9 50 ... 33 dBm 000 ... 999 000 ... 999 30 ... 0 dB 116 ... 25 dBm 11 ... 20 dB 46 ... 158 dB 0 ... 16383 (frequency band dependent) 0 ... 40 dB 115 ... 25 dBm
Arg
Description DRX (Discontinuous Reception) coefficient for serving cell. The maximum transmit power the terminal is allowed to use. Mobile Country Code of serving cell. Mobile Network Code of serving cell. May consist of two or three digits. P-CCPCH Ec/No for the serving cell. P-CCPCH received signal code power for the serving cell. P-CCPCH signal-to-interference ratio for the serving cell. Pathloss for serving cell. UARFCN used for control signaling by the serving cell. This UARFCN may also be used for traffic.
Cell reselection parameter Qhyst1s for serving cell: hysteresis value. See 3GPP 25.304, section 5.2.6.1.5. Cell reselection parameter Qrxlevmin, specifying the minimum required RxLev in the serving cell. See 3GPP 25.304, section 5.2.6.1.5. Cell reselection parameter Sintersearch for serving cell: threshold for interfrequency measurements. See 3GPP 25.304, section 5.2.6.1.5.
0 ... 91 dB
119
IE Name Serving S-intrasearch Threshold Serving Treselection (s) Speed (km/h) Speed (mph) T3212
Range/Unit 0 ... 91 dB
Arg
Description Cell reselection parameter Sintrasearch for serving cell: threshold for intrafrequency measurements. See 3GPP 25.304, section 5.2.6.1.5. Cell reselection timer value Treselections. See 3GPP 25.304, section 5.2.6.1.5. Speed in km/h. Speed in mph. Value of timer T3212 controlling periodic location area updating. Given as raw value in deci-hours (0 means no periodic updates). See 3GPP 24.008. Current time in text format: HH:MM:SS.mm, where mm = decimal seconds. Current time in ms.
0 ... 31 s 0 ... 250 km/h 0 ... 155 mph 0 ... 255 deci-hours
Time
Text
Time (ms)
0 ... 86400000 ms
Timeslot IEs: General remark Timeslot Code Count Timeslot Code Count HSPDSCH Timeslot Count DL Timeslot Count UL
0 ... 8
0 ... 6
Number of channelization codes in use for each timeslot during a non-HS session. Number of channelization codes in use for each timeslot during an HS session. Number of timeslots in use on downlink. Number of timeslots in use on uplink.
0 ... 16
0 ... 6
1 ... 6 1 ... 6
120
IE Name Timeslot Direction Timeslot DPCH RSCP (dBm) Timeslot DPCH RSCP Sum (dBm) Timeslot ISCP (dBm) Timing Advance (chips) Transport Channel BLER DL Transport Channel BLER Total DL Transport Channel Count DL Transport Channel ID DL
Range/Unit Text 116 ... 25 dBm 116 ... 25 dBm 116 ... 25 dBm 16 ... 240 chips 0 ... 100 %
Description Direction of transmission for each used timeslot: UL or DL. Dedicated Physical Channel received signal code power, measured and reported per timeslot. Sum of DPCH received signal code powers for all reported timeslots. The summing is done in the mW domain. Interference signal code power for each timeslot. Timing Advance parameter stated in chip units. Block error rate for each downlink transport channel. Argument: Transport channel index.
0 ... 6
1 ... 32
Block error rate averaged over all downlink transport channels. Number of downlink transport channels. Identity of each downlink transport channel. Argument: Transport channel index.
1 ... 32
1 ... 32
UE transmit power in dBm. Valid only in connected mode. Uplink pilot channel transmit power.
121
3.5.
IE Support in Connectable Equipment Some elements are presentable only with a subset of the connectable devices. See the table in section 5.1, page 286. Information Element Table
IE Name Access Channel Max Capsule Size Access Channel Preamble Size Access Initial Power Offset Access Max Req Seq Access Max Rsp Seq Access Num Step Access Power Increment Range/Unit 0 ... 7 Arg Description Maximum number of Access Channel or Enhanced Access Channel frames in an Access Channel Message Capsule, less 3. Number of frames in the Access Channel or Enhanced Access Channel preamble, less 1. Initial power offset or adjustment used in the open loop power control procedure. Maximum number of access probe sequences for each 1x access attempt (used for regular MS origination). Maximum number of access probe sequences for each 1x access attempt (used in case of PACA origination). Number of access probes in each 1x access probe sequence, less 1. Open loop transmit power increment in units of 1 dB between successive access probes in an 1x access probe sequence. Sequence number of access probe sent during 1x access attempt. Sequence number of access probe sequence sent during 1x access attempt.
0 ... 255
0 ... 15
122
IE Name Active Set IEs: General remark Active Set Band Class Active Set Cell Name
Range/Unit
Arg
Description
Text
1 ... 6
Frequency band class for each active set member. See 3GPP2 TS C.S0057B. Cell name for each active set member as defined in cell file (if available). Requires that a cell file has been loaded.
Text
1 ... 6
Active Set Channel Active Set Count Active Set DCCH Code Channel Active Set DCCH QOF Mask Id Active Set Ec Active Set Ec/Io Active Set Ec/Io Sum Active Set FCH Code Channel Active Set FCH QOF Mask Id
1 ... 6 1 ... 6
Channel number of RF channel used by each active set member. The number of members in the active set, whether in idle or traffic mode. DCCH code channel used by each active set member. DCCH QOF mask id used by each active set member. Received signal code power for each active set member. Signal-to-noise ratio (Ec/Io in dB) for each active set member. Total signal-to-noise ratio (Ec/Io in dB) for all active set members. The summing is done in the mW domain. FCH code channel used by each active set member. FCH QOF mask id used by each active set member.
0 ... 3
1 ... 6
1 ... 6 1 ... 6
1 ... 6
0 ... 3
1 ... 6
123
IE Name Active Set PN Active Set SCH Code Channel Active Set SCH QOF Mask Id Active Set Serving Io Altitude (ft)
Description Pilot PN offset for each active set member. SCH code channel used by each active set member. SCH QOF mask id used by each active set member. Total received signal power in the serving RF channel. Height above sea level in feet. Reported by positioning equipment.
0 ... 3
1 ... 6
125 ... 25 dBm 1312 ... 29028 ft 400 ... 8848 m 120 ... 30 dBm 0 ... 255 0 ... 7
Altitude (m)
Received signal strength indicator for AMPS. AMPS Supplemental Code Channel. Transmit power level in AMPS traffic state. See TIA/EIA-553-A, section 2.1.2.2; ERP levels in dBW are found in Table 2.1.2-1. Base ID transmitted in Layer 3 message System Parameters. Number of Blocked Call events. Regarding this event, see section 7.3. Number of Dropped Call events. Regarding this event, see section 7.3. Number of Call End events. Regarding this event, see section 7.3.
Base ID Call Blocked Count Call Dropped Count Call Success Count
124
Arg
Description Calculated as: # blocks / (# blocks + # drops + # ends) where blocks = Blocked Call events drops = Dropped Call events ends = Call End events Regarding the events, see section 7.3.
0 ... 100 %
Calculated as: # drops / (# blocks + # drops + # ends) where blocks = Blocked Call events drops = Dropped Call events ends = Call End events Regarding the events, see section 7.3.
Candidate Set IEs: General remark Candidate Set Band Class Candidate Set Cell Name Candidate Set Channel
The argument, where present, points to the candidate set member index. Text 1 ... 6 Frequency band class for each candidate set member. See 3GPP2 TS C.S0057-B. Cell name for each candidate set member as defined in cell file (if available). Channel number of RF channel used by each candidate set member.
Text
1 ... 6
1 ... 6
1 ... 6
The number of candidate set members. Received signal code power for each candidate set member.
125
Description Signal-to-noise ratio (Ec/Io in dB) for each candidate set member. Pilot PN offset for each candidate set member. One of: Entering CDMA Sync Channel Paging Channel Traffic Channel Initialization Traffic Channel Exit
MCC, Mobile Country Code. The number dialed to initiate the current call. Valid only while a call is in progress. Number of failed EV-DO access attempts divided by total number of EVDO access attempts. Maximum number of access probe sequences per EV-DO access attempt. Sequence number of access probe sent during EV-DO access attempt. Number of access probes in each EVDO access probe sequence. Sequence number of access probe sequence sent during EV-DO access attempt.
EV-DO Access Failure Rate (%) EV-DO Access Max Probe Seq EV-DO Access Probe Count EV-DO Access Probe Num Step EV-DO Access Probe Seq Count
0 ... 255
126
Range/Unit 0 ... 3
Arg
Description Result of EV-DO access attempt: 0: ACAck not received 1: ACAck received 2: TCA message received 3: Probe Interrupted
EV-DO Active Set IEs: General remark EV-DO Active Set DRC Cover EV-DO Active Set DRC Lock EV-DO Active Set Drop Timer Active
The argument, where present, points to the active set member index.
0 ... 7
1 ... 6
EV-DO: DRC cover for each active set member. EV-DO: DRC lock status for each active set member: Locked/ Unlocked. EV-DO: Drop timer for each active set member. 0: Inactive 1: Active
Text
1 ... 6
0 ... 1
1 ... 6
0 ... 1
1 ... 6
EV-DO: Drop timer status for each active set member. 0: Drop timer running 1: Drop timer expired
EV-DO Active Set MAC Index EV-DO Active Set Predicted DRC EV-DO Active Set Predicted SINR
0 ... 127
1 ... 6
EV-DO: The medium access control index associated with each active set member. EV-DO: DRC cover for the active set pilot currently having the best predicted SINR. EV-DO: Predicted SINR for the active set pilot currently having the best predicted SINR.
0 ... 7
30 ... 15 dB
127
Arg 1 ... 6
Description EV-DO: For each active set member, specifies the slots in which a new reverse activity bit can be transmitted. See 3GPP2 TS C.S0024, section 9.3.1.3.2.2.3. EV-DO: For each active set member, the rate of reverse activity bits during the last PN roll (16 slots), calculated as (number of ones) / 16. EV-DO: Reverse power control index for each active set member. EV-DO: For each active set member, a running average of the last 64 reverse power control bits, showing the recent trend of the power control. See 3GPP2 TS C.S0024, section 9.2.1.2.4.2. EV-DO: DRC cover for the current serving active set pilot. EV-DO: PN offset for the current serving active set pilot. EV-DO: RPC index for the current serving active set pilot. EV-DO: SINR for the current serving active set pilot. EV-DO: Signal to interference-plusnoise ratio for each active set member. EV-DO: Center of search window for each active set member. Given in chip units.
EV-DO Active Set RAB Usage (%) EV-DO Active Set RPC Index EV-DO Active Set RPC Indication
0 ... 100 %
1 ... 6
0 ... 15 1 ... 1
1 ... 6 1 ... 6
EV-DO Active Set Serving DRC EV-DO Active Set Serving PN EV-DO Active Set Serving RPC EV-DO Active Set Serving SINR EV-DO Active Set SINR EV-DO Active Set Window Center
0 ... 7
0 ... 511
0 ... 15
1 ... 6 1 ... 6
128
Arg
Description EV-DO: RRI at which the reverse link packet was transmitted. This should be EV-DO Condition RRI (kbit/s); if Actual RRI < Condition RRI, then the reverse rate has been demoted, as there is not enough data to be sent. EV-DO: Air Link Management Protocol State. 0: Inactive 1: Initialization 2: Idle 3: Connected
0 ... 5
0 ... 5
EV-DO access terminal state. 0: Inactive (AT switched to 1x or is in Deep Sleep) 1: Acquisition 2: Sync 3: Idle 4: Access 5: Connected
EV-DO AT State (Text) EV-DO Attempt Duration EV-DO Attempt Transaction Id EV-DO Best Pilot PN EV-DO Best SINR
Same as EV-DO AT State (Num) but in text format. Time (in slots) taken to complete the EV-DO access attempt. Transaction ID of EV-DO access attempt. EV-DO: PN offset for the active set pilot currently having the best predicted SINR. EV-DO: Predicted SINR for the active set pilot currently having the best predicted SINR.
0 ... 511
30 ... 15 dB
129
IE Name EV-DO Candidate Set IEs: General remark EV-DO Candidate Set Drop Timer Active EV-DO Candidate Set Drop Timer Expired EV-DO Candidate Set Window Center EV-DO Color Code EV-DO Condition RRI (kbit/s)
Range/Unit
Arg
Description
The argument, where present, points to the candidate set member index.
0 ... 1
1 ... 6
EV-DO: Drop timer for each candidate set member. 0: Inactive 1: Active
0 ... 1
1 ... 6
EV-DO: Status of drop timer for each candidate set member. 0: Drop timer running 1: Drop timer expired
0 ... 23768
1 ... 6
EV-DO: Center of search window for each candidate set member. Given in chip units. EV-DO base station color code. EV-DO reverse rate indication calculated according to the algorithm in 3GPP2 TS C.S0024, section 8.5.6.1.5.2. Compare EV-DO Actual RRI (kbit/s). EV-DO Connected State. 0: Inactive 1: Open
EV-DO Connected State (Num) EV-DO Connection Failure Rate (%) EV-DO DRC Rate Received (kbit/s)
0 ... 5
0 ... 100 %
Number of failed EV-DO connection attempts divided by total number of EVDO connection attempts. EV-DO received downlink data rate, instantaneous value.
130
IE Name EV-DO DRC Rate Received Average (kbit/s) EV-DO DRC Rate Requested (kbit/s) EV-DO DRC Rate Requested Average (kbit/s) EV-DO DRC State EV-DO Finger IEs: General remark EV-DO Finger Antenna Selection
Arg
Text
0 ... 1
1 ... 12
Antenna(s) selected for each EV-DO finger. Of interest only if the access terminal is equipped with two antennas and is enabled to use both. 0: Antenna 0 1: Antenna 1
30 ... 15 dB
1 ... 12
EV-DO: When antenna diversity is enabled, for each finger, the cumulative energy of all search results for antenna 0. EV-DO: When antenna diversity is enabled, for each finger, the cumulative energy of all search results for antenna 1.
30 ... 15 dB
1 ... 12
131
Range/Unit 0 ... 1
Arg 1 ... 12
Description State of EV-DO antenna diversity. Relevant only if the access terminal is equipped with two antennas. 0: Not enabled 1: Enabled
1 ... 12
The index of the EV-DO finger. EV-DO Mobile Station Time Reference: the access terminals current timing reference based on the sync channel time (in slots) and on the finger lock to the earliest arriving usable multipath of a pilot. Given in units of 1/8 chip. Finger delay for each EV-DO finger, expressed as an offset from the current MSTR. Given in units of 1/8 chip. EV-DO: PN offset of pilot currently used as timing reference. EV-DO RPC Cell Index. Pilots that have the same RPC bit for the AT share the same value.
EV-DO Finger MSTR Error EV-DO Finger MSTR Pilot PN EV-DO Finger RPC Cell Index EV-DO FL IEs: General remark EV-DO FL Bad Packet Count
1 ... 12
1 ... 12
The argument, where present, points to a DRC index. Arg 0 = DRC index 0x1, etc. 0 ... 231 1 0 ... 25 For each DRC index, the number of packets on the forward link received with bad CRC, accumulated over latest reporting period. For each DRC index, the number of packets on the forward link received with bad CRC, accumulated from start. For each DRC index, the percentage of bad packets on the forward link. Given for the latest reporting period.
0 ... 231 1
0 ... 25
0 ... 100 %
0 ... 25
132
IE Name EV-DO FL Bad Packet Rate Multi User (Total) EV-DO FL Good Packet Count EV-DO FL Good Packet Count (Total) EV-DO FL Good Packet Rate EV-DO FL Multi Throughput (kbit/s) EV-DO FL Packet Size EV-DO FL Throughput (kbit/s) EV-DO Hybrid Mode
Arg 0 ... 25
Description For each DRC index, the percentage of bad multi-user packets on the forward link, accumulated from start. For each DRC index, the number of packets on the forward link received with good CRC, accumulated over latest reporting period. For each DRC index, the number of packets on the forward link received with good CRC, accumulated from start. For each DRC index, the percentage of good packets on the forward link. Given for the latest reporting period. Instantaneous EV-DO forward link throughput in the multi-user case.
0 ... 231 1
0 ... 25
0 ... 231 1
0 ... 25
0 ... 25
0 ... 25
For each DRC index, the raw bit rate on the forward link (kbit/s). Instantaneous EV-DO forward link throughput. Tells whether the access terminal is in hybrid mode: On or Off. A terminal in hybrid mode is monitoring both 1x and EV-DO paging channels in idle mode. EV-DO Idle State: 0: Inactive 1: Monitor 2: Sleep 3: Connection Setup 4: Suspend
0 ... 5
133
Range/Unit 0 ... 5
Arg
Description EV-DO Init State: 0: Inactive 1: Network Determination 2: Pilot Acquisition 3: Sync
EV-DO Neighbor Set Age EV-DO Neighbor Set Window Offset EV-DO Neighbor Set Window Size EV-DO OVHD Message State (Num)
0 ... 65535
1 ... 40
EV-DO: Age counter for each neighbor set member. See 3GPP2 TS C.S0024, section 6.6.6.1.2.7. EV-DO: Offset (from MSTR) of search window used for each neighbor set member. EV-DO: Size of search window used for each neighbor set member. EV-DO Overhead Message State: 0: Inactive 1: Process All Messages 2: Sleep 3: Frequency Change In Progress 4: Access Handoff In Progress 5: Wait For Link
1 ... 40
1 ... 40
EV-DO PA State EV-DO PER Instantaneous (%) EV-DO PER Long (%) EV-DO PER Short (%) EV-DO Power Ratio ACK Pilot
State of EV-DO power amplifier: On or Off. EV-DO Packet Error Rate, immediate value (no averaging). EV-DO Packet Error Rate, running average over (approximately) 600 reports. EV-DO Packet Error Rate, running average over (approximately) 60 reports. EV-DO: Offset between the ACK Channel and Pilot Channel output powers.
134
IE Name EV-DO Power Ratio Aux Pilot EV-DO Power Ratio Data Pilot EV-DO Power Ratio DRC Pilot EV-DO Power Ratio RRI Pilot EV-DO Reverse Rate AN Limit EV-DO Reverse Rate Average (kbit/s) EV-DO Reverse Rate Current (kbit/s) EV-DO Reverse Rate PA Limit EV-DO Revision EV-DO RL IEs: General remark EV-DO RL Max Traffic To Pilot EV-DO RL Packet Count (Total)
Range/Unit 20 ... 20 dB 20 ... 20 dB 20 ... 20 dB 20 ... 20 dB 0 ... 1800 kbit/s 0 ... 1800 kbit/s
Arg
Description EV-DO: Offset between Aux Channel and Pilot Channel output powers. EV-DO: Offset between Data Channel and Pilot Channel output powers. EV-DO: Offset between DRC Channel and Pilot Channel output powers. EV-DO: Offset between RRI Channel and Pilot Channel output powers. EV-DO reverse link data rate limit imposed by access network (AN). EV-DO reverse link data rate, running average.
EV-DO reverse link data rate, instantaneous value. EV-DO reverse link data rate limit imposed by power amplifier (PA). EV-DO revision: Rev 0 or Rev A.
The argument, where present, points to a reverse link current rate index. 20 ... 20 dB 0 ... 231 1 EV-DO: Maximum offset between the Traffic Channel and Pilot Channel output powers. For each RL current rate, the number of packets sent on the reverse link from start of logfile/since device connect.
1 ... 5
135
IE Name EV-DO RL Packet Rate EV-DO RL Packet Size EV-DO RL Throughput EV-DO RLP RX Duplicate Bytes EV-DO Route Update State
Arg 1 ... 5
Description Percentage distribution showing the current usage of the reverse link current rates. Based on latest report. For each RL current rate, the raw bit rate on the reverse link. Instantaneous EV-DO reverse link throughput. EV-DO: Number of received duplicate frames. EV-DO Route Update Protocol State: 0: Inactive 1: Idle 2: Connection Setup 3: Connected 4: Synchronize Connection Setup
1 ... 5
0 ... 4
EV-DO Session Failure Rate (%) EV-DO Session Full UATI EV-DO Session RATI EV-DO Session Result
0 ... 100 %
Number of failed EV-DO session attempts divided by total number of EVDO session attempts. EV-DO: Full (128-bit) Unicast Access Terminal Identifier allocated to the access terminal. EV-DO: Random Access Terminal Identifier allocated to the terminal. Success or failure of EV-DO session attempt, as indicated by the AN giving the AT a UATI assignment or not. 0: Failure 1: Success
Text
136
Range/Unit 0 ... 5
Arg
Description EV-DO session state. One of: 0: Closed 1: AMP setup 2: AT-initiated negotiation 3: AN-initiated negotiation 4: Open 5: Closing
EV-DO Session State (Text) EV-DO Session Transaction ID EV-DO Session UATI Color Code
Text
Same as EV-DO Session State (Num) but in text format. EV-DO: Transaction ID sent in UATIRequest message; see 3GPP2 TS C.S0024, section 5.3.7.2.1. EV-DO: UATI Color Code sent in UATIAssignment message. The AN sets this field to the Color Code associated with the subnet to which the UATI belongs. See 3GPP2 TS C.S0024, section 5.3.7.2.2. EV-DO: List of active UATIs (Unicast Access Terminal Identifiers), given as 32-bit values (lowest 4 bytes of full UATI). Argument: Sequence number.
0 ... 255
0 ... 255
1 ... 8
EV-DO UATI (Num) EV-DO UATI Count F-DCCH Bitrate (kbit/s) F-DCCH Enabled F-DCCH Frame Length (bits)
0 ... 65535 0 ... 8 0 ... 162600 kbit/s Text 0 ... 65535 bits
1 ... 8
Same as EV-DO UATI (Hex) but in decimal format. EV-DO: Number of active UATIs. Forward link DCCH bit rate configuration. State of forward link DCCH: Used/ Not Used. Number of bits in a forward link DCCH physical layer frame.
137
IE Name F-DCCH Frame Size (ms) F-DCCH MUX PDU F-DCCH Radio Configuration FER DCCH (%) FER FCH (%) FER SCH0 (%) FER SCH1 (%) FER Total (%) F-FCH Bitrate (kbit/s) F-FCH Frame Length (bits) F-FCH Frame Size (ms) F-FCH MUX PDU F-FCH Radio Configuration
Range/Unit Text
Arg
Description Forward link DCCH frame size in milliseconds. Forward link DCCH MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Forward link DCCH Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. Frame erasure rate on the DCCH (Digital Control Channel). Frame erasure rate on the FCH (Fundamental Channel). Frame erasure rate on the SCH0 (Supplemental Channel 0). Frame erasure rate on the SCH1 (Supplemental Channel 1). Frame erasure rate calculated over all forward channels. Forward link FCH bit rate configuration. Number of bits in a forward link FCH physical layer frame. Forward link FCH frame size in milliseconds. Forward link FCH MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Forward link FCH Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1.
Text
1 ... 9
0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 162600 kbit/s 0 ... 65535 bits Text Text 1 ... 9
138
Range/Unit 0 ... 15
Arg
Description Forward link FCH rate bitmask. A combination of: 0x01 (Full Rate allowed), 0x02 (1/2 Rate allowed), 0x04 (1/4 Rate allowed), and 0x08 (1/8 Rate allowed)
0 ... 2
Forward link FCH traffic type; one of: 0: No forward traffic 1: Primary traffic 2: Secondary traffic
F-FCH Traffic Type (Text) Finger IEs: General remark Finger Count Finger Delay Delta (chips) Finger Energy (dB) Finger Energy Sum (dB) Finger Pilot PN Finger Status Firmware Version FPC F-DCCH Setpoint Avg
Text
0 ... 12 2 ... 512 chips 32 ... 15 dB 64 ... 10 dB 0 ... 511 Text Text 0 ... 255 dB/8
1 ... 12 1 ... 12
Number of valid fingers. The position of each finger (in chips) relative to the earliest finger arrived. Signal-to-noise ratio for each finger: Ec/Io for 1x fingers, SINR for EV-DO fingers. Total signal-to-noise ratio for all fingers, instantaneous value: Ec/Io for 1x fingers, SINR for EV-DO fingers. Pilot PN for each finger. Status of each finger: a combination of Reference, Locked, and Assigned. Version number of device firmware. The current outer loop estimation Eb/Io setpoint of the forward link DCCH in units of 0.125 dB.
1 ... 12 1 ... 12
139
IE Name FPC F-FCH Setpoint Avg FPC F-SCH0 Setpoint Avg Frame Offset
Range/Unit 0 ... 255 dB/8 0 ... 255 dB/8 0 ... 15 See Description
Arg
Description The current outer loop estimation Eb/Io setpoint of the forward link FCH in units of 0.125 dB. The current outer loop estimation Eb/Io setpoint of the forward link SCH0 in units of 0.125 dB. A time skewing of Traffic Channel frames from System Time in integer multiples of 1.25 ms. The maximum frame offset is 15 1.25 ms = 18.75 ms.
See the description (cellular technology independent) under GSM, page 22. 0 ... 5 Forward link SCH rate. 0: 1X 1: 2X 2: 4X 3: 8X 4: 16X 5: 32X
F-SCH0 Bitrate (kbit/s) F-SCH0 Enabled F-SCH0 Frame Length (bits) F-SCH0 MUX PDU F-SCH0 Radio Configuration Hardware Hardware ID
F-SCH0 channel bit rate configuration. State of F-SCH0 channel: Used/Not Used. Number of bits in an F-SCH0 physical layer frame. F-SCH0 MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. F-SCH0 Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. Device model. ESN, Electronic Serial Number.
Text Text
140
Range/Unit 0 ... 360 degrees 90 ... 90 degrees Text 180 ... 180 degrees Text
Arg
Description Direction of travel measured in degrees clockwise from north. Reported by positioning equipment. Latitude recorded by positioning equipment. Latitude as text. For the presentation format, see RA UM appendix C.4. Longitude recorded by positioning equipment. Longitude as text. For the presentation format, see RA UM appendix C.4.
Latitude Latitude (Text) Longitude Longitude (Text) Missing Neighbor IEs: General remark Missing Neighbor Cell Name Missing Neighbor Ec/Io Missing Neighbor PN Mobile Identity Number Mode Mode (Num)
These elements are obtained when using a scanner in follow phone mode (see DC UM section 12.3). The argument points to a neighbor index. Text 1 ... 40 Cell name of each missing neighbor as defined in cell file, if available. Signal-to-noise ratio for each missing neighbor. PN offset of each missing neighbor. Mobile Identity Number of the device. Same as Mode (Num) (which see) but in text format: No service etc. 1: No service 2: Idle mode 3: Dedicated mode (4: Limited service mode) (5: Scan mode) 6: Packet mode (7: Packet Idle mode)
1 ... 40 1 ... 40
141
Range/Unit 1 ... 8
Arg
Mode - System (Text) MSM Revision Neighbor Set IEs: General remark Neighbor Set Band Class Neighbor Set Cell Name
Text Text
Same as Mode - System but in text format. Qualcomm chipset family (e.g. MSM 6800).
The argument, where present, points to the neighbor set member index. Text 1 ... 40 Frequency band class for each neighbor set member. See 3GPP2 TS C.S0057-B. Cell name for each neighbor set member as defined in cell file (if available). Requires that a cell file has been loaded.
Text
1 ... 40
Neighbor Set Channel Neighbor Set Count Neighbor Set Ec Neighbor Set Ec/Io Neighbor Set PN Network ID Network ID (Hex)
0 ... 1199 0 ... 40 157 ... 10 dBm 32 ... 0 dB 0 ... 511 0 ... 65535 Text: 0000 ... FFFF
Channel number of RF channel used by each neighbor set member. The number of neighbor set members. Received signal code power for each neighbor set member. Signal-to-noise ratio (Ec/Io in dB) for each neighbor set member. Pilot PN offset for each neighbor set member. Network Identification (NID). Same as Network ID but in hexadecimal format.
142
IE Name Number Of DSC Channels PESQ elements Pilot PN Increment Pilot Set IEs: General remark Pilot Set Band Class Pilot Set Cell Name
Range/Unit 0 ... 15
Arg
See the description (cellular technology independent) under GSM, page 38. 1 ... 15 Inter-sector pilot PN increment used by the AN in assigning PN offsets to sectors.
The argument, where present, points to the pilot set member index. Text Text 1 ... 52 1 ... 52 Frequency band class for each pilot set member. See 3GPP2 TS C.S0057-B. Cell name for each pilot set member as defined in cell file (if available). Requires that a cell file has been loaded.
Pilot Set Cell Type Pilot Set Channel Pilot Set Count Pilot Set Ec Pilot Set Ec/Io Pilot Set PN Polluters IEs: General remark
Text 0 ... 1199 0 ... 52 157 ... 10 dBm 32 ... 0 dB 0 ... 511
Type of pilot: Active, Candidate, or Neighbor. Channel number of RF channel used by each pilot. Total number of pilots in active, candidate, and neighbor sets. Received signal code power for each pilot set member. Signal-to-noise ratio for each pilot set member. PN offset for each pilot set member.
These elements are obtained when using a scanner in follow phone mode: see DC UM, section 12.3. Current refers to the polluter data derived from the latest scan report. Top List refers to cumulative polluter statistics amassed since start of logfile/since device connect.
143
Arg 1 ... 6
Description PN offset of each current active set member. Argument: Active set member index.
Text
1 ... 5
Cell name of each current polluter, as defined in cell file (if available). Argument: Rank of this polluter among current polluters.
32 ... 0 dB
1 ... 5
Signal-to-noise ratio for each current polluter. Argument: Rank of this polluter among current polluters.
0 ... 511
1 ... 5
PN offset of each current polluter. Argument: Rank of this polluter among current polluters.
Text
1 ... 5
Cell name of each polluter on the top list. Argument: Rank on polluter top list.
0 ... 1199
1 ... 5
RF channel number of each polluter on the top list. Argument: Rank on polluter top list.
0 ... 511
1 ... 5
PN offset of each polluter on the top list. Argument: Rank on polluter top list.
Protocol Revision Base (Num) Protocol Revision Base (Text) Protocol Revision Mobile (Num)
0 ... 7
Text
Same as Protocol Revision - Base (Num) but in text format. Phone protocol revision (P-Rev).
0 ... 7
144
IE Name Protocol Revision Mobile (Text) Protocol Revision In Use (Num) Protocol Revision In Use (Text) R-DCCH Bitrate (kbit/s) R-DCCH Enabled R-DCCH Frame Length (bits) R-DCCH MUX PDU R-DCCH Radio Configuration RF Mode
Range/Unit Text
Arg
Description Same as Protocol Revision - Mobile (Num) but in text format. Protocol revision (P-Rev) negotiated between phone and base station. Same as Protocol Revision In Use (Num) but in text format. Reverse link DCCH bit rate configuration. State of reverse link DCCH: Used/ Not Used. Number of bits in a reverse link DCCH physical layer frame. Reverse link DCCH MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Reverse link DCCH Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. For Analog and CDMA: <technology> <phone state>, where <technology> is one of Analog, CDMA, 1xEV-DO, and <phone state> is one of Init, Idle, Access, Traffic.
0 ... 7
Text
1 ... 9
Text
For EV-DO: <technology> <AT state>, where <technology> is as above, and <AT state> is one of Inactive, Acquisition, Sync, Idle, Access, Connected.
145
Range/Unit 0 ... 13
Arg
Description RF Mode mapped to an integer. 0: Analog, Init 1: Analog, Idle 2: Analog, Access 3: Analog, Traffic 4: CDMA, Init 5: CDMA, Idle 6: CDMA, Access 7: CDMA, Traffic 8: EV-DO, Inactive 9: EV-DO, Acquisition 10: EV-DO, Sync 11: EV-DO, Idle 12: EV-DO, Access 13: EV-DO, Connected
R-FCH Bitrate (kbit/s) R-FCH Frame Length (bits) R-FCH MUX PDU R-FCH Radio Configuration R-FCH Rate
Reverse link FCH bit rate configuration. Number of bits in a reverse link FCH physical layer frame. Reverse link FCH MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Reverse link FCH Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. Reverse link FCH rate bitmask. A combination of: 0x01 (Full Rate allowed), 0x02 (1/2 Rate allowed), 0x04 (1/4 Rate allowed), and 0x08 (1/8 Rate allowed)
0 ... 15
0 ... 2
Reverse link FCH traffic type; one of: 0: No reverse traffic 1: Primary traffic 2: Secondary traffic
Text
146
IE Name RLP DL Avg. Throughput (kbit/s) RLP DL Throughput (kbit/s) RLP Erasure Rate (%) RLP Retransmitted Frames Rx (%) RLP Retransmitted Frames Tx (%) RLP Rx Channel Rate (kbit/s)
Range/Unit 0 ... 4000 kbit/s 0 ... 4000 kbit/s 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 162600 kbit/s
Arg
Description Averaged throughput on downlink at RLP level (16 s sliding window). Valid for both 1x and EV-DO. Instantaneous throughput on downlink at RLP level. Valid for both 1x and EVDO. Erasure rate at RLP level. Retransmitted frames on downlink at RLP level. Retransmitted frames on uplink at RLP level. RLP downlink physical channel bit rate configuration. Argument: 0: FCH 1: DCCH 2: SCH0 3: SCH1 4: SCCH0 5: SCCH1 6: SCCH2 7: SCCH3 8: SCCH4 9: SCCH5 10: SCCH6 11: SCCH7 12: PDCH
0 ... 12
Total bytes transferred on downlink at RLP level. Total bytes transferred on uplink at RLP level.
147
Arg 0 ... 12
Description RLP uplink physical channel bit rate configuration. Argument: See RLP Rx Channel Rate (kbit/s).
Averaged throughput on uplink at RLP level (16 s sliding window). Valid for both 1x and EV-DO. Instantaneous throughput on uplink at RLP level. Valid for both 1x and EVDO. Reverse link SCH rate. 0: 1X 1: 2X 2: 4X 3: 8X 4: 16X 5: 32X
R-SCH0 Bitrate (kbit/s) R-SCH0 Enabled R-SCH0 Frame Length (bits) R-SCH0 MUX PDU R-SCH0 Radio Configuration Rx Power
Reverse link SCH0 bit rate configuration. State of reverse link SCH0: Used/Not Used. Number of bits in a reverse link SCH0 physical layer frame. Reverse link SCH0 MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Reverse link SCH0 Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. Received signal power. Valid for both 1x and EV-DO.
1 ... 9
148
IE Name Scanned 1st Freq. elements Scanned 1st Freq. Band Scanned 1st Freq. Cell Name Scanned 1st Freq. Channel Scanned 1st Freq. Delay Scanned 1st Freq. Delay Spread Scanned 1st Freq. Ec Scanned 1st Freq. Ec/Io Scanned 1st Freq. Io Scanned 1st Freq. Pilot PN Scanned 1st Freq. Pilots Count Scanned 1st Freq. Strongest elements Scanned 2nd (etc.) Freq. elements
Range/Unit
Arg
Description
Pilot scanning: First scanned RF channel. Argument: The sorting order depends on the setting in the General window: see DC UM section 12.3.4.1. Text Text 1 ... 512 Band class for scanned RF channel. See 3GPP2 TS C.S0057-B. Cell names corresponding to each scanned pilot. Requires that a cell file has been loaded. Channel number of scanned RF channel. Pilot delay in chips for each scanned pilot. See DC UM section 12.3.1. Delay spread in chips for each scanned pilot. See DC UM section 12.3.1. Received signal code power of each scanned pilot. Peak Ec/Io for each scanned pilot. Total signal power in RF channel. PN offset for each scanned pilot. Number of pilots scanned.
0 ... 1199 3 ... 60 chips 0 ... 63 chips 157 ... 10 dBm 32 ... 0 dB 125 ... 25 dBm 0 ... 511 0 ... 512
Pilot scanning: First scanned RF channel. The strongest pilots are sorted by descending peak Ec/Io. Argument (1 ... 32): 1 means the pilot with highest peak Ec/Io, etc. Pilot scanning: Second (etc.) scanned RF channel. Argument: The sorting order depends on the setting in the General window: see DC UM section 12.3.4.1.
149
Range/Unit
Arg
Description
Pilot scanning: Second (etc.) scanned RF channel. The strongest pilots are sorted by descending peak Ec/Io. Argument (1 ... 32): 1 means the pilot with highest peak Ec/Io, etc. 0 ... 1199 1 ... 512 RSSI scanning: RF channel number of each RF channel scanned. Argument: 1 means the RF channel with the lowest number, etc.
1 ... 512
RSSI scanning: The number of RF channels scanned. RSSI scanning: RSSI for each RF channel. Argument: 1 means the RF channel with the lowest number, etc.
These elements contain the strongest pilots irrespective of scanned RF channel. The pilots are sorted by descending peak Ec/Io. Argument (1 ... 32): 1 means the pilot with the highest peak Ec/Io, etc.
Searcher State
Text
Searcher state, e.g. Acquisition, TCH operation. Valid for both 1x and EVDO. Size of search window used for pilots in the active set. For the mapping to PN chip length see IS-95, Table 6.6.6.2.11. Size of search window used for pilots in the neighbor set. Size of search window used for pilots in the remaining set (see 3GPP2 TS C.S0005-A, page 1-18). Hex string containing the 128-bit sector address of the serving sector. Format: 0011:2233:4455:6677:8899:AABB:CC DD:EEFF
Searcher Window A
Text
150
IE Name Service ID Service Option (Num) Service Option (Text) Slot Cycle Index Soft Handoff State
Arg
Description Radio Link Protocol service ID. Service Option for the current session. See 3GPP2 TS C.R1001. Same as Service Option (Num) but in text format. Slot cycle index described in 3GPP2 TS C.S0005-A, section 2.6.2.1.1.3. Soft handoff state. One of No Soft Handoff, 2-Way, 3-Way, 4-Way, 5-Way, 6-Way. Derived from the information element Active Set Count.
These elements are populated by spectrum analysis scanning. The argument, where present, is simply a sequence number pointing to scanned frequencies as indicated by the Spectr Ana Sc DL Freq element. 870 ... 900 MHz 0 ... 2560 1 ... 2560 Spectrum analysis: Scanned frequencies on downlink in ascending order. Spectrum analysis: The number of downlink frequencies swept by the scan. Spectrum analysis: Spectrum analysis: RSSI of downlink frequencies scanned. AQM: The length of time it takes for the speech to travel from the Call Generator to the MTU and back to the Call Generator again. This element only appears in merged logfiles (see RA UM section 17.2).
Spectr Ana Sc DL Freq Spectr Ana Sc DL No Of Freq Spectr Ana Sc DL RSSI Speech Path Delay
1 ... 2560
151
IE Name SQI MOS Station Class Mark (hex) Subnet Mask System ID System ID (Hex) T-Add (dB)
Range/Unit 1 ... 5 MOS Text 0 ... 255 0 ... 65535 Text (0000 ... FFFF) 32 ... 0 dB 63 ... 0 See Description
Arg
Description SQI expressed on the MOS scale. See DC UM chapter 28. Defined in 3GPP2 TS C.S0005-A, section 2.3.3. Sector subnet identifier. System Identification (SID) in decimal format. System Identification (SID) in hexadecimal format. Pilot detection threshold (sign reversed). See 3GPP2 TS C.S0005-A, section 2.6.6.2.6.2. Pilot detection threshold (expressed in units of 0.5 dB and sign reversed). See 3GPP2 TS C.S0005-A, section 1.1.2.2. Active set versus candidate set comparison threshold. See 3GPP2 TS C.S0005-A, section 2.6.6.2.5.2. Active set versus candidate set comparison threshold (expressed in units of 0.5 dB). Pilot drop threshold (sign reversed). See 3GPP2 TS C.S0005-A, section 2.6.6.2.3. Pilot drop threshold (expressed in units of 0.5 dB and sign reversed).
T-Add (Num)
T-Comp (dB)
T-Comp (Num)
T-Drop (dB)
T-Drop (Num)
T-TDrop (Num)
Drop timer value, mapped to an integer value according to 3GPP2 TS C.S0005-A v6.0, Table 2.6.6.2.3-1.
152
Arg
Description Drop timer value in seconds. See 3GPP2 TS C.S0005-A v6.0, Table 2.6.6.2.3-1.
Tx Adjust
Tx Adjust power control parameter. Valid for both 1x and EV-DO. Equal to Closed Loop Adjust parameter when in EV-DO mode.
Tx Power
3.5.1.
153
3.6.
Notes on CINR The number of samples on which to base the CINR mean values and standard deviations is set in the WiMAX scan setup dialog (DC UM section 13.3.1, Number of Samples for Stats). However, this figure only serves as a guideline to the scanner; in practice the scanner may on some occasions use a lower number of samples as input to the statistics calculation. This number is reported in the Samples Taken elements (see below). Note that as power level fluctuations become minute, the standard deviation likewise approaches zero and hence tends towards negative infinity when expressed in dB. A large negative number has been used as the lower endpoint for the standard deviation range. Information Element Table
IE Name Altitude (ft) Range/Unit 1312 ... 29028 ft 400 ... 8848 m Text Text Text 0 ... 360 degrees 90 ... 90 degrees Text Arg Description Height above sea level in feet. Reported by positioning equipment. Height above sea level in meters. Reported by positioning equipment. Version number of device firmware. Scanner model. Hardware identification string. Direction of travel measured in degrees clockwise from north. Reported by positioning equipment. Latitude recorded by positioning equipment. Latitude as text. For the presentation format, see RA UM appendix C.4.
Altitude (m)
154
IE Name Longitude Longitude (Text) Mode Mode (Num) Mode - System Mode - System (Text) Sc Channel IEs: General remark Sc Channel [indx] Sc Channel Count Sc Channel Profile (Text) [indx] Sc Channel RSSI (dBm) [indx]
Range/Unit 180 ... 180 degrees Text Text 1 ... 7 1 ...8 Text
Arg
Description Longitude recorded by positioning equipment. Longitude as text. For the presentation format, see RA UM appendix C.4. Not used. Not used. Not used. Not used.
These elements are obtained from preamble scanning. The argument, where present, points to the position of the channel in the list of scanned channels. 0 ... 1580 0 ... 1499 0 ... 1499 0 ... 1499 RF channel number of each channel scanned. See WiMAX Forum Mobile System Profile version 1.4, Table 130. The number of channels scanned. The WiMAX RF profile to which each scanned channel belongs. The total power in all the allowed preamble subcarriers of the WiMAX signal, gated during the preamble symbol time. This is the sum of all three segment powers. Running mean value of channel RSSI.
Sc Channel RSSI Mean (dBm) [indx] Sc Channel RSSI Samples Taken [indx]
155
IE Name Sc Channel RSSI Std. Dev. (dB) [indx] Sc Channel Segment 0 Power (dBm) [indx] Sc Channel Segment 1 Power (dBm) [indx] Sc Channel Segment 2 Power (dBm) [indx] Sc Preamble IEs: General remark Sc Preamble Center Frequency Offset (Hz) [indx] Sc Preamble Channel [indx] Sc Preamble Cha-PI (Text) [indx] Sc Preamble CINR (dB) [indx] Sc Preamble CINR Mean (dB) [indx]
Description Running standard deviation for channel RSSI. The total power in the preamble subcarriers allocated to segment 0, gated during the preamble symbol time. The total power in the preamble subcarriers allocated to segment 1, gated during the preamble symbol time. The total power in the preamble subcarriers allocated to segment 2, gated during the preamble symbol time.
0 ... 1499
0 ... 1499
These elements are obtained from preamble scanning. The argument, where present, indicates the position of the preamble in the list of detected preambles. 10000 ... 10000 Hz 0 ... 99 The center frequency offset of the channel on which each preamble was detected.
0 ... 99 0 ... 99
Channel number for each preamble detected. For each preamble detected, a text string containing RF channel number and preamble index. Carrier to interference-plus-noise ratio (CINR) for each preamble detected. Running mean value of carrier to interference-plus-noise ratio (CINR) for each preamble detected.
37 ... 60 dB 37 ... 60 dB
0 ... 99
0 ... 99
156
IE Name Sc Preamble CINR Samples Taken [indx] Sc Preamble CINR Std. Dev. (dB) [indx] Sc Preamble Count Sc Preamble Index [indx] Sc Preamble Operator ID [indx] Sc Preamble Power (dBm) [indx] Sc Preamble Profile (Text) [indx] Sc Preamble Sector ID [indx] Sc Preamble Segment Index [indx] Sc RSSI IEs: General remark Sc RSSI Bandwidth (kHz) Sc RSSI Channel
Range/Unit 0 ... 32
Arg 0 ... 99
Description Number of samples used to calculate CINR statistics (mean, standard deviation). Running standard deviation of carrier to interference-plus-noise ratio (CINR) for each preamble detected. The number of preambles detected. Index of each detected preamble as defined in the tables in IEEE 802.16e, section 8.4.6.1.1. Operator ID for each detected preamble. RSSI of each detected preamble.
0 ... 99
0 ... 99
Text
0 ... 99
0 ... 99
0 ... 99
The WiMAX RF profile to which each detected preamble belongs. Sector ID for each detected preamble. Segment index for each detected preamble.
Text 0 ... 2
0 ... 99 0 ... 99
These elements are obtained from RSSI scanning. The argument, where present, points to the position of the channel in the list of scanned channels. Text The bandwidth scanned around the center frequency of each channel. Channel number of each channel scanned. See WiMAX Forum Mobile System Profile version 1.4, Table 130.
0 ... 1580
0 ... 1499
157
IE Name Sc RSSI Channel Count Sc RSSI Frequency (kHz) Sc RSSI Profile (Text) Sc RSSI RSSI (dBm) Sc Strongest Channel IEs: General remark Sc Strongest Channel Sc Strongest Channel Profile (Text) Sc Strongest Channel RSSI (dBm) Sc Strongest Channel RSSI Mean (dBm) Sc Strongest Channel RSSI Samples Taken Sc Strongest Channel RSSI Std. Dev. (dB) Sc Strongest Channel Segment 0 Power (dBm)
Range/Unit 0 ... 1500 0 ... 6000 kHz Text 140 ... 20 dBm
The WiMAX RF Profile to which each scanned channel belongs. RSSI for each scanned channel.
Preamble scanning. Information element components sorted by decreasing channel RSSI. Argument: 1 = channel with highest RSSI, etc. 0 ... 1580 Text 1 ... 32 1 ... 32 RF channel number. WiMAX RF Profile.
140 ... 20 dBm 140 ... 20 dBm 140 ... 20 dBm 200 ... 20 dB 140 ... 20 dBm
1 ... 32
Channel RSSI.
1 ... 32
1 ... 32
Number of samples used to calculate channel RSSI statistics (mean, standard deviation). Running standard deviation of channel RSSI. The total power in the preamble subcarriers allocated to segment 0, gated during the preamble symbol time.
1 ... 32
1 ... 32
158
IE Name Sc Strongest Channel Segment 1 Power (dBm) Sc Strongest Channel Segment 2 Power (dBm) Sc Strongest (CINR) IEs: General remark Sc Strongest (CINR) Channel Sc Strongest (CINR) Cha-PI (Text) Sc Strongest (CINR) CINR Sc Strongest (CINR) Preamble Index Sc Strongest RSSI IEs: General remark Sc Strongest RSSI (dBm) Sc Strongest RSSI Channel Sc Strongest RSSI Frequency (MHz)
Arg 1 ... 32
Description The total power in the preamble subcarriers allocated to segment 1, gated during the preamble symbol time. The total power in the preamble subcarriers allocated to segment 2, gated during the preamble symbol time.
1 ... 32
Preamble scanning. Information element components sorted by decreasing preamble CINR. Argument: 1 = preamble with highest CINR, etc. 0 ... 1580 1 ... 32 RF channel number.
Text
1 ... 32
Text string containing RF channel number and preamble index. CINR. Preamble index.
1 ... 32 1 ... 32
RSSI scanning. Information element components sorted by decreasing RSSI. Argument: 1 = channel with highest RSSI, etc. 140 ... 20 dBm 0 ... 1580 0 ... 6000 MHz 1 ... 32 1 ... 32 1 ... 32 RSSI of each channel included in RSSI scan. RF channel number of each RSSI scanned channel. Frequency of each RSSI scanned channel.
159
IE Name Sc Strongest RSSI Profile (Text) Sc Strongest (Preamble Power) IEs: General remark Sc Strongest (Preamble Power) Channel Sc Strongest (Preamble Power) Cha-PI (Text) Sc Strongest (Preamble Power) CINR Sc Strongest (Preamble Power) Preamble Index Spectr Ana IEs: General remark
Range/Unit Text
Arg 1 ... 32
Preamble scanning. Information element components sorted by decreasing preamble RSSI. Argument: 1 = preamble with highest RSSI, etc.
0 ... 1580
1 ... 32
RF channel number.
Text
1 ... 32
1 ... 32
CINR.
1 ... 32
Preamble index.
These elements are populated by spectrum analysis scanning. The argument, where present, is simply a sequence number pointing to scanned frequencies as indicated by the Spectr Ana Sc DL Freq (MHz) element. 0 ... 6 106 MHz 0 ... 3001 140 ... 20 dBm 1 ... 3001 1 ... 3001 Scanned frequencies on downlink in ascending order. The number of downlink frequencies swept by the scan. RSSI of downlink frequencies scanned.
Spectr Ana Sc DL Freq (MHz) Spectr Ana Sc DL No Of Freq Spectr Ana Sc DL RSSI (dBm)
160
Arg
Description Speed in km/h. Speed in mph. Current time in text format: HH:MM:SS.mm, where mm = decimal seconds. Current time in ms.
Time (ms)
0 ... 86400000 ms
161
3.7.
This section lists the information elements in the Data category, i.e. those obtained when performing data service testing. The Data category contains two kinds of elements: Application-level data service measurements. In the PC, these are taken in the Winsock interface. Application-level measurements reflect the performance experienced directly by the user, as opposed to the performance at lower levels in the protocol hierarchy (RLC, LLC, RLP, etc.). Statistics on the dial-up connection obtained from Microsofts Remote Access Service (RAS), i.e. Dial-up Networking. Remember that not all data services are run over a dial-up connection (see DC UM section 14.11).
The Data information elements are mostly independent of the bearer service used (packet-switched or circuit-switched). A number of elements are however bearer-specific. Note the meaning of the terms connection and session which are used in the explanations below. They are defined in DC UM section 14.12.1.1.
IE Name App. Bytes Received Range/Unit 0 ... 2 109 bytes Arg Description Number of bytes received at the application level since dial-up. Login information is included in this byte count. Number of bytes sent at the application level since dial-up, including login information. Current throughput for data received at the application level (current downlink throughput). Current throughput for data sent at the application level (current uplink throughput). Time since dial-up, i.e. how long the currently established data service connection has been up. Given in hours, minutes, and seconds.
App. Bytes Sent App. Throughput DL (kbit/s) App. Throughput UL (kbit/s) Connection Duration
0 ... 2 109 bytes 0 ... 80000 kbit/s 0 ... 80000 kbit/s Text hh:mm:ss
162
IE Name Data Connection Type IP Address NDIS/RAS IEs: General remark NDIS/RAS Bytes Received NDIS/RAS Bytes Sent NDIS/RAS Current Throughput DL (kbit/s) NDIS/RAS Current Throughput UL (kbit/s) Packets Received Per Second Packets Sent Per Second Ping Delay (ms)
Range/Unit Text
Arg
Text
These elements are valid for a RAS connection as well as an NDIS connection. However, in Windows Vista, these elements are currently not updated for NDIS. 0 ... 2 109 bytes 0 ... 2 109 bytes 0 ... 80000 kbit/s Number of bytes received over the current data connection. Number of bytes sent over the current data connection. Downlink throughput on the current data connection.
0 ... 2 109
Number of packets received per second. Number of packets sent per second. Round-trip time for an individual Ping Response during the current Ping session. Valid only during Ping sessions.
Size in bytes of the packet sent with the Ping command. Valid only during Ping sessions.
163
IE Name RAS IEs: General remark RAS Alignment Errors RAS Buffer Overrun Errors RAS Compression Ratio In RAS Compression Ratio Out RAS CRC Errors RAS Frames Received RAS Frames Sent RAS Framing Errors RAS Hardware Overrun Errors RAS Timeout Errors Session App. Bytes Received Session App. Bytes Sent
Range/Unit
Arg
Description
These elements are valid only if the device uses a RAS dial-up connection. 0 ... 2 109 0 ... 2 109 0 ... 2000 Number of alignment errors on the current dial-up connection. Number of buffer overrun errors on the current dial-up connection. Compression ratio for the data being received on the current dial-up connection. Compression ratio for the data being sent on the current dial-up connection. Number of cyclic redundancy check (CRC) errors on the current dial-up connection. Number of frames received over the current dial-up connection. Number of frames sent over the current dial-up connection. Number of framing errors on the current dial-up connection. Number of hardware overrun errors on the current dial-up connection. Number of timeout errors on the current dial-up connection. Number of bytes received at the application level during the current session. Number of bytes sent at the application level during the current session.
0 ... 2000
0 ... 2 109
0 ... 2 109 0 ... 2 109 0 ... 2 109 0 ... 2 109 0 ... 2 109 0 ... 2 109 bytes 0 ... 2 109 bytes
164
IE Name Session App. Mean Throughput DL (kbit/s) Session App. Mean Throughput UL (kbit/s) Session Current Packet Loss (%) Session Current Throughput DL (kbit/s)
Arg
Description Mean throughput, calculated over the whole of the current session, for data received at the application level (mean downlink throughput). Mean throughput, calculated over the whole of the current session, for data sent at the application level (mean uplink throughput). Current packet loss level in percent. (Useful when testing video streaming.) Same as App. Throughput DL (kbit/s) except that this element is valid only while a data transfer session is in progress. This element is more suitable to use for statistics, since it will not contain any zeroes from periods of inactivity. Same as App. Throughput UL (kbit/s) except that this element is valid only while a data transfer session is in progress. This element is more suitable to use for statistics, since it will not contain any zeroes from periods of inactivity. Time for which the current session has been ongoing. Given in hours, minutes, and seconds. Description of the current session in plain text, e.g. FTP DL: www.my_server.com/temp/my_file.txt. Average of the latest 30 VSQI Realtime Scores (which see).
1 ... 5 MOS
165
Arg
Description Video Streaming Quality Index (realtime score which is regularly updated during the streaming session, unlike the overall VSQI score for an entire session, which appears in the Session End report). See DC UM chapter 31.
3.8.
This section lists the information elements in the GSM Uplink category, i.e. those originating from MTR files. These information elements are found only in Data Collection. The GSM Uplink category includes further elements besides those listed, including RxLev and RxQual (Full and Sub) for both uplink and downlink. All such elements have precisely the same ranges and meanings as the corresponding elements in section 3.1, and so they have been omitted here. No uplink information elements are valid when running GPRS/EGPRS. No uplink data can be recorded in MTR files when running a data service.
IE Name BCCH Allocation Used DTX DL Used DTX UL Used Neighbor CI Range/Unit Text Arg Description BCCH Allocation (BS) list currently used by the phone. Use of DTX on downlink. Use of DTX on uplink. Cell Identity of neighbor cell. Argument: Indicates neighbor ranking: 1 gives the neighbor with the highest rank, etc.
1 ... 6
166
Range/Unit Text
Arg 1 ... 6
Description Indicates the algorithm used to compute the ranking value. One of Undefined K-value L-value High signal cell Low signal cell.
Argument: Indicates neighbor ranking: 1 gives the neighbor with the highest rank, etc. Neighbor Ranking Value 127 ... 128 1 ... 6 This value is usually negative. A higher value means a higher ranking. If a ranking value of a neighbor becomes positive, this neighbor probably soon will become the serving cell. Argument: Indicates neighbor ranking: 1 gives the neighbor with the highest rank, etc. Path Loss Full Path Loss Sub Power Level BS 47 ... 190 dB 47 ... 190 dB 0 ... 15 See Description 0 ... 31 See Description Pathloss, Full value. Pathloss, Sub value. Base station transmit power. Regarding the value range, see 3GPP 45.005, section 4.1.2. Valid only in dedicated mode. Phone transmit power (compare MS Power Control Level in section 3.1). Regarding the value range, see 3GPP 45.005, section 4.1.1. Valid only in dedicated mode. Phone transmit power in dBm (compare MS Tx Power (dBm) in section 3.1). Valid only in dedicated mode.
Power Level MS
0 ... 31 dBm
167
Arg
Description Uplink Speech Quality Index. Extended Timing Advance. Valid only in dedicated mode. For the significance of the parameter value, see 3GPP 45.010.
168
4.
4.1.
IE Name Altitude
Version number of device firmware. Device model. Hardware identification string. Example: Equal to IMEI for UMTS user terminals; equal to ESN for CDMA user terminals. Direction of travel measured in degrees clockwise from north. International Mobile Equipment Identity, the unique equipment identity of the phone. Latitude as text. For the presentation format, see RA UM appendices C and D. Longitude as text. For the presentation format, see RA UM appendices C and D.
Heading IMEI
Latitude
Text
Longitude
Text
169
IE Name Mode
Arg
Description 1: No service 2: Idle mode 3: Dedicated mode 4: Limited service mode 5: Scan mode 6: Packet mode 7: Packet Idle mode 1: WCDMA 2: GSM 3: CDMA (1x) 4: 1xEV-DO 5: Analog 6: WiMAX 7: LTE 8: TD-SCDMA Speed of vehicle. Unit: km/h or mph.
Mode - System
1 ... 8 or Text
Speed
Time
Text
170
4.2.
Properties of Information Elements: The Asterisk Column In the column marked *, a set of codes is used to state conditions under which an information element is valid: a non-trivial condition must be fulfilled for the element to be valid not valid: the element is normally valid, but in certain circumstances it is not (code ends in ) extended compared to the simplest GSM case: the element sometimes carries more information, for example when frequency hopping is used (code ends in +)
If nothing is written in the asterisk column, the element is always valid and is reported by all supported phones. Code c g g+ Valid if a cell file is loaded. Valid when running GPRS. Not valid for voice. The element is richer for (E)GPRS, in one of the following ways: g more values, i.e. more arguments e.g. C/I values have a more complex meaning e.g. C/I Hopping List (average over timeslots) larger range of possible values e.g. Channel Type. Meaning
171
Code h+
Meaning The element is richer if frequency hopping is used. If frequency hopping is used, the element covers all channels in the hopping list. No GPRS connection: One value for each channel (arguments 0 through 63) GPRS: One value for each timeslot used on each channel (arguments 0 through 64 8 1 = 511). Exception: C/I Hopping List has only one value for each channel (arguments 0 through 63).
If frequency hopping is not used, the element contains values for the single channel employed. No GPRS connection: One single value (argument 0). GPRS: One value for each timeslot used on the channel (arguments 0 through 7).
Example: C/I. hc+ If frequency hopping is used, the element covers all channels in the hopping list. One value for each channel (arguments 0 through 63). No separate values for each timeslot for a GPRS connection. Example: C/I Hopping List. hs hs+ Valid when running HSCSD. Not valid for voice. The element is richer for HSCSD, in one of the following ways: hs more values, i.e. more arguments e.g. C/I values have a more complex meaning e.g. C/I Hopping List (average over timeslots) larger range of possible values e.g. Channel Type.
172
Full and Sub Values Information elements with Full in their names are calculated on all blocks. Information elements with Sub in their names are calculated only on the blocks known to be sent also when downlink DTX is active (in each 104multiframe, one TCH block with SID information and one SACCH block). GSM RxLev Units GSM RxLev units are defined in 3GPP 45.008, section 8.1.4.
4.2.1.
GAN
Range/Unit 1 ... 4 or Text Arg * Description State of GA-RC or GA-CSR protocol. 1: GA-RC Deregistered 2: GA-RC Registered 3: GA-CSR Idle 4: GA-CSR Dedicated
GAN Access Point MAC Address GAN Access Point SSID GAN GERAN Cell Id
Text
MAC address of connected WLAN access point (BSSID in IEEE 802.11 standard). Service Set Identifier of connected WLAN access point. Cell Identity in the GSM EDGE Radio Access Network (GERAN). Included in Register and Discovery messages if the phone is in an area with GSM coverage and GSM-RR is the serving RR entity. Retrieved from GSM System Information. Location Area Code in the GSM network. Retrieved from GSM System Information. Mobile Country Code in the GSM network. Retrieved from GSM System Information.
0 ... 65535
173
Arg
Description Mobile Network Code in the GSM network. Retrieved from GSM System Information. Used to indicate the presence of GERAN coverage in the phones current location. 0: Normal service 1: Limited service 2: Phone has not found GERAN coverage 3: Phone has found GERAN coverage, service state unknown
0 ... 3 or Text
0 ... 255
Indicates to the GANC the number of times the phone has been redirected (from one GANC to another) without obtaining service. WLAN signal level. 0: Unusable 1: Poor 2: Adequate 3: Good 4: Excellent 5: Not applicable
0 ... 5 or Text
WLAN received signal strength. Points to the default GANC the phone should use. Points to the default GANC Security Gateway the MS should use.
174
Range/Unit 0, 2
Arg
Description Indicates whether a selection has been made on the GAN Mode Selection tab of the phones property page. (At the outset no option is selected.) See DC UM section 15.4.3.4. 0: No 2: Yes
4.2.2.
4.2.2.1.
GPRS/EGPRS
Channel
Argument = Timeslot sequence number means that 0 represents the first used timeslot, 1 the second, etc.; the argument value does not equate to the corresponding timeslot index.
IE Name C31 Range/Unit 127 ... 127 dB Arg * g Description GPRS signal strength threshold criterion C31. Valid both in packet idle and packet dedicated mode. C32 127 ... 127 dB g GPRS cell ranking criterion C32. Valid both in packet idle and packet dedicated mode. Cell EGPRS Support Text: Yes/No EGPRS supported/not supported in the cell. This information is available also to non-EGPRS phones. Indicates whether GPRS is supported in the cell. Retransmission buffer size on downlink (RLC protocol level).
175
IE Name EGPRS Window Size UL GMM State GRR State LLC Window Size DL LLC Window Size UL Network Control Order
Range/Unit 64 ... 1024 RLC blocks Text Text 1 ... 255 LLC blocks 1 ... 255 LLC blocks Text
Arg
g g
State of GMM protocol: Idle, Ready, or Standby. State of GRR protocol: Packet Idle or Packet Transfer. LLC retransmission buffer size on downlink. LLC retransmission buffer size on uplink.
Cell reselection behavior of phone. One of NC0, NC1, NC2: NC0: MS reselection, no measurement reports NC1: MS reselection, measurement reports NC2: Network reselection See 3GPP 45.008, section 10.1.4.
Text
Handling of paging in the network. I: All paging on GPRS channels; Gs signaling interface present II: All paging on PCH; no Gs III: All circuit-switched paging on PCH, all packet-switched paging on PPCH; no Gs.
0 ... 8
g hs
176
IE Name Number of Used Timeslots UL PBCCH Timeslot PDP Access Point Name
Range/Unit 0 ... 8
Arg
* g hs g g
Description Number of timeslots in use on uplink. Timeslot used for PBCCH/ PCCCH, if any. Host name or network address for each active PDP context. Argument: PDP context index.
0 ... 7 Text
1 ... 11
PDP Address
Text
1 ... 11
PDP Context Activation Time PDP Contexts Active PDP Delay Class
Time from PDP Context Activation Request to PDP Context Activation Accept. Number of active PDP contexts. Delay class as defined by subscription. Argument: PDP context index.
1 ... 11
g g
3 ... 11
1 ... 11
Text
1 ... 11
PDP NSAPI
5 ... 15
1 ... 11
Network SAPI (Service Access Point Identifier). Argument: PDP context index.
Text
1 ... 11
177
Range/Unit Text
Arg 1 ... 11
* g
Text
1 ... 11
Text
1 ... 11
TFI DL
0 ... 31
Temporary Flow Id on uplink. Used to identify a one-block flow. Temporary Flow Id on downlink. Used to identify a one-block flow. Type of channel in each timeslot on downlink. See Channel Type. Argument: Timeslot sequence number.
TFI UL
0 ... 31
Text
0 ... 7
g hs
Text
0 ... 7
g hs
Type of channel in each timeslot on uplink. See Channel Type. Argument: Timeslot sequence number.
Timeslot Used DL
Text
0 ... 7
g hs
Timeslots used on downlink. Argument: Timeslot sequence number. Timeslots used on uplink. Argument: Timeslot sequence number. Temporary Logical Link Identifier.
Timeslot Used UL
Text
0 ... 7
g hs
TLLI
178
Range/Unit 0 ... 7
Arg 0 ... 7
* g
Description Flags, one for each timeslot, indicating to the phone when it is allowed to send. Argument: Timeslot sequence number.
4.2.2.2.
Measurement
Argument = Timeslot sequence number means that 0 represents the first used timeslot, 1 the second, etc.; the argument value does not equate to the corresponding timeslot index.
IE Name Attach Time C Value Range/Unit 0 ... 60000 ms 0 ... 63 GSM RxLev units Text Arg * g Description Time from Attach Request to Attach Complete. Normalized signal level received at the MS (normalization with running average filter). g Modulation coding scheme used on downlink. EDGE: One of: MCS-1 ... MCS-9 MCS-5-7 MCS-6-9 MCS-3 (pad) MCS-6 (pad). MCS-5-7 and MCS-6-9 are explained in 3GPP 44.060. (pad) means that an RLC block is retransmitted using MCS-3 and MCS-6 respectively. GPRS: One of CS-1 ... CS-4.
Coding Scheme DL
179
IE Name Coding Scheme DL Usage (Own Data) Coding Scheme DL Usage (Total)
Arg 1 ... 4
* g
Description Distribution of coding scheme usage on downlink (for own data only). Argument: 1 means CS-1, etc.
0 ... 100 %
1 ... 4
Distribution of coding scheme usage on downlink (overall, not limited to own data). Argument: 1 means CS-1, etc.
Coding Scheme UL
Text
Modulation coding scheme used on uplink. For the possible values, see Coding Scheme DL. These elements contain the distribution of coding scheme usage (on the downlink and for own data only) for each timeslot. Argument: Timeslot sequence number.
0 ... 100 %
0 ... 7
g g g g
Coding scheme currently used on downlink. Coding scheme currently used on uplink. Modulation coding scheme currently used on downlink. Modulation coding scheme currently used on uplink. Mean value of bit error probability as reported in the Layer 3 message EGPRS Packet Downlink Ack/Nack. Coded according to the table in 3GPP 45.008, section 8.2.5.
180
Arg
Description Variance of bit error probability as reported in the Layer 3 message EGPRS Packet Downlink Ack/Nack. Coded according to the table in 3GPP 45.008, section 8.2.5.
Short-term mean value of bit error probability extracted from Layer 1. Coded according to the table in 3GPP 45.008, section 8.2.5.
Short-term variance of bit error probability extracted from Layer 1. Coded according to the table in 3GPP 45.008, section 8.2.5.
Text
Indicates whether Link Adaptation (LA) or Incremental Redundancy (IR) is used on the uplink. Distribution of modulation coding scheme usage (on downlink and for own data only) for each timeslot. Argument 1: Timeslot sequence number. Argument 2: Modulation coding scheme index.
0 ... 100 %
0 ... 7; 1 ... 9
Modulation DL Modulation UL
Text Text
181
Arg 0 ... 7
* g
Description Percentage of downlink PDCH capacity currently used for control signaling, or not used at all. Argument: Timeslot sequence number.
0 ... 100 %
0 ... 7
Percentage of the available uplink PDCH capacity currently used for control signaling. Argument: Timeslot sequence number.
0 ... 100 %
0 ... 7
Percentage of the available uplink PDCH capacity that is currently unused. Argument: Timeslot sequence number.
0 ... 100 %
0 ... 7
Percentage of the downlink PDCH capacity currently used for other users data. Argument: Timeslot sequence number.
0 ... 100 %
0 ... 7
Percentage of the downlink PDCH capacity currently used for own data. Argument: Timeslot sequence number.
0 ... 100 %
0 ... 7
Percentage of the available uplink PDCH capacity currently used for own data. Argument: Timeslot sequence number.
182
IE Name RLA_P
Arg
* g
4.2.3.
LLC BLER DL
0 ... 100 % 0 ... 100 % 0 ... 2 109 bytes 0 ... 2 109 bytes 0 ... 400 kbit/s
LLC BLER UL LLC Bytes Received DL LLC Bytes Sent UL LLC Throughput DL
g g
LLC Throughput UL
183
Range/Unit 0 ... 100 % 0 ... 100 % 0 ... 2 109 bytes 0 ... 2 109 bytes 0 ... 400 kbit/s
Arg
* g
Description Percentage of RLC data blocks erroneously decoded on downlink. Percentage of RLC data blocks resent on uplink. Number of bytes received at the RLC protocol level since GPRS attach. Number of bytes sent at the RLC protocol level since GPRS attach. Data throughput (including protocol headers, but excluding retransmissions) on downlink at RLC protocol level. Data throughput (as defined above) on downlink at RLC protocol level, relative to theoretical maximum for current channel setup (coding scheme, number of timeslots). Data throughput (including protocol headers, but excluding retransmissions) on uplink at RLC protocol level. Data throughput (as defined above) on uplink at RLC protocol level, relative to theoretical maximum for current channel setup (coding scheme, number of timeslots). Percentage of RLP data blocks erroneously decoded on downlink. Percentage of RLP data blocks resent on uplink.
RLC BLER UL RLC Bytes Received DL RLC Bytes Sent UL RLC Throughput DL
g g
0 ... 100 %
RLC Throughput UL
0 ... 100 %
RLP BLER DL
hs
RLP BLER UL
hs
184
Arg
* hs
Description Number of bytes received at the RLP protocol level since dialup. Number of bytes sent at the RLP protocol level since dialup. Data throughput (including protocol headers, but excluding retransmissions) on downlink at RLP protocol level. Data throughput (as defined above) on downlink at RLP protocol level, relative to theoretical maximum for current channel setup (coding scheme, number of timeslots). Data throughput (including protocol headers, but excluding retransmissions) on uplink at RLP protocol level. Data throughput (as defined above) on uplink at RLP protocol level, relative to theoretical maximum for current channel setup (coding scheme, number of timeslots). Percentage of SNDCP data blocks erroneously decoded on downlink. Percentage of SNDCP data blocks resent on uplink. Number of bytes received at the SNDCP protocol level since GPRS attach.
hs
hs
0 ... 100 %
hs
RLP Throughput UL
0 ... 60 kbit/s
hs
0 ... 100 %
hs
g g
185
Arg
* g
Description Number of bytes sent at the SNDCP protocol level since GPRS attach. Data throughput (including protocol headers, but excluding retransmissions) on downlink at SNDCP protocol level. Data throughput (including protocol headers, but excluding retransmissions) on uplink at SNDCP protocol level.
SNDCP Throughput UL
4.2.4.
MS Behavior
186
Range/Unit 0, 2
Arg
* g
Description Use of GPRS class forcing function in phone. 0: Not activated 2: Activated Not supported by any currently connectable phones; see section 5.2 for details.
0, 2
Use of GPRS multislot class forcing function in phone. 0: Not activated 2: Activated Not supported by any currently connectable phones; see section 5.2 for details.
0, 2
Use of power class forcing function in phone. 0: Not activated 2: Activated Not supported by any currently connectable phones; see section 5.2 for details.
0, 2
Use of PDP Context Request modification function in phone. 0: Not activated 2: Activated Not supported by any currently connectable phones; see section 5.2 for details.
0, 2
Use of idle mode RxQual measurement function in phone. 0: Not activated 2: Activated Not supported by any currently connectable phones; see section 5.2 for details.
187
Range/Unit 0, 2
Arg
Description Use of ignore/reverse cell barred function in phone. See DC UM sections 15.2.3.6, 15.3.2.3, 15.4.1.3, 15.4.2.2, 15.4.3.2. 0: Not activated 2: Activated
MS Behavior Modified
Indicates whether the phones behavior has been changed from the default. Most of what follows is applicable only to Sony Ericsson GSM phones. Empty string: No modification of phone behavior B: Modification of behavior not related to channel selection (the information elements Adjacent Scan, Band Control, Forced Power Class, Idle Channel Quality, Multiband Reporting) C: Modification of channel selection behavior (the information elements Disable Handover, Ignore Cell Barred, Prevent Handover List Active, Serving Cell List Active, Target Handover) G: Modification of GPRS behavior (the information elements Forced GPRS Class, Forced Multislot Class, Forced Quality of Service). Any combination of these letters may appear.
Multiband Reporting
0, 2
Not used; the feature has been removed from TEMS Investigation. The element is retained in order to maintain compatibility with old logfiles.
188
Range/Unit 0, 2
Arg
Description Use of prevent handover function in phone (handover to certain cells prevented in dedicated mode). See DC UM section 15.2.3.9. 0: Not activated 2: Activated
0, 1, 2
Use of lock on channel function in phone. See DC UM sections 15.2.3.7, 15.3.2.1, 15.4.1.2, 15.4.2.1. 0: Not activated 1: Ordered by user, but not yet activated 2: Activated
Target Handover
0, 1, 2
Use of handover lock function in phone (handover is restricted to a chosen set of cells). See DC UM section 15.2.3.9. 0: Not activated 1: Ordered by user, but not yet activated 2: Activated
4.2.5.
Neighbors
All these elements have attributes which specify different sorting orders: Unsorted: Neighbors arranged in order of ascending ARFCN. Sorted: Neighbors sorted by signal strength, regardless of frequency band. Band Sorted: Neighbors sorted by signal strength for each frequency band separately. Bands sorted by ascending frequency.
189
Range/Unit See ARFCN BCCH, section 4.2.8.1 00 ... 77 (octal) or Text 127 ... 127 dB 127 ... 127 dB 127 ... 127 dB 127 ... 127 dB 0 ... 65535 (dec) or Text (hex)
Arg 1 ... 32
Neighbor BSIC
1 ... 32
Base Station Identity Codes for neighbor cells (in text format). Pathloss parameter C1 for neighbor cells. Cell reselection parameter C2 for neighbor cells. g g GPRS signal strength threshold criterion C31 for neighbor cells. GPRS cell ranking criterion C32 for neighbor cells. Cell identities of neighbor cells.
Text
1 ... 32
190
Range/Unit 1 ... 6
Arg 1 ... 32
* c
Description Indicates, for each neighbor cell, the input used by the algorithm determining the neighbor cell name, and the result of the cell search (where applicable): 1: MCC, MNC, LAC, CI used. 2: BSIC, ARFCN, and position information used. Unique cell found matching these parameters within a 35 km radius. 3: BSIC, ARFCN, and position information used. Several matching cells found within a 35 km radius, closest cell selected. 4: Serving cell found with the method denoted by Cell Name Algorithm = 1; this neighbor identified as a cell appearing in the serving cells neighbor list and having matching BSIC and ARFCN. 5: Serving cell found with the method denoted by Cell Name Algorithm = 2; this neighbor identified as a cell appearing in the serving cells neighbor list and having matching BSIC and ARFCN. 6: Serving cell found with the method denoted by Cell Name Algorithm = 3; this neighbor identified as a cell appearing in the serving cells neighbor list and having matching BSIC and ARFCN.
Neighbor LAC
1 ... 32
191
Arg 1 ... 32
Text
Neighbor list (obtained from System Information) of strongest cell scanned. The list is given in text format, for example: [ARFCN: 17, BSIC: 3-2] 7, 18, 32. The data within square brackets pertains to the strongest cell, and the neighbor ARFCNs follow.
4.2.6.
Quality Measurement
The Frequent AQM elements, uplink and downlink scores, only appear in merged logfiles (see RA UM section 17.2). Uplink PESQ scores likewise only appear in merged logfiles. Downlink PESQ scores, as well as the remaining AQM measurements (all other elements prefixed with PESQ below), appear in merged as well as unmerged logfiles. However, prior to merging, all such data lags behind other data in the logfile. See RA UM section 17.2.2.
192
Range/Unit Text
Arg 0 ... 3
Description Current active set of AMR speech codecs on downlink, each codec being described by a text string, e.g. 12.2 kbit/s rate. Argument: 0 gives the first member of the active set, etc.
Text
0 ... 3
Current active set of AMR speech codecs on uplink, each codec being described by a text string, e.g. 12.2 kbit/s rate. Argument: 0 gives the first member of the active set, etc.
0 ... 100 %
0 ... 7
Distribution of downlink AMR codec usage for the current call. Invalid if no call is ongoing. Argument: Indicates the AMR codec. 0: 12.2 kbit/s 1: 10.2 kbit/s 2: 7.95 kbit/s 3: 7.40 kbit/s 4: 6.70 kbit/s 5: 5.90 kbit/s 6: 5.15 kbit/s 7: 4.75 kbit/s
0 ... 100 %
0 ... 7
Distribution of uplink AMR codec usage for the current call. Invalid if no call is ongoing. Argument: AMR Codec Call DL.
193
Arg 0 ... 7
Description Distribution of downlink AMR codec usage since the phone started using the current serving cell. Argument: AMR Codec Call DL.
0 ... 100 %
0 ... 7
Distribution of uplink AMR codec usage since the phone started using the current serving cell. Argument: AMR Codec Call DL.
AMR Codec DL
0 ... 100 %
0 ... 3
Current distribution of downlink AMR codec usage across the active set being used. Argument: 0 gives the first member of the active set, etc., the members being ordered as in AMR Active Set DL.
AMR Codec UL
0 ... 100 %
0 ... 3
Current distribution of uplink AMR codec usage across the active set being used. Argument: 0 gives the first member of the active set, etc., the members being ordered as in AMR Active Set UL.
AMR Hysteresis
0 ... 15
1 ... 3
Hysteresis values in AMR mode switch mechanism. Argument: One hysteresis value for each possible mode transition (a maximum of four AMR codecs can be active simultaneously).
AMR Threshold
0 ... 63
1 ... 3
Threshold values in AMR mode switch mechanism. Argument: See AMR Hysteresis.
194
IE Name Frequent AQM Score DL Frequent AQM Score UL Frequent AQM Sentence DL Frequent AQM Sentence UL PESQ Echo Attenuation PESQ Echo Correlation PESQ Echo Delay PESQ Echo Power PESQ Score DL PESQ Score UL PESQ Sentence DL
Range/Unit 1 ... 5 MOS-PESQ 1 ... 5 MOS-PESQ 0 ... 7 0 ... 7 0 ... 100 dB 0 ... 5 0 ... 1000 ms 0 ... 100 dB 1 ... 5 MOS-PESQ 1 ... 5 MOS-PESQ 0 ... 3
Arg
Description Frequent AQM score for last speech sentence played on the downlink. Frequent AQM score for last speech sentence played on the uplink. Downlink Frequent AQM sentence index. Uplink Frequent AQM sentence index. AQM: Echo attenuation on downlink. AQM: Echo correlation on downlink. AQM: Echo delay on downlink. AQM: Echo power on downlink. AQM: PESQ score for last two speech sentences played on the downlink. AQM: PESQ score for last two speech sentence played on the uplink. AQM: Downlink PESQ sentence index. Each index represents the two sentences over which the corresponding PESQ score was calculated. 0: Sentences 0 + 1 1: Sentences 2 + 3 2: Sentences 4 + 5 3: Sentences 6 + 7
195
IE Name PESQ Sentence UL PESQ Volume Speech Codec Speech Path Delay
Range/Unit 0 ... 3
Arg
Description AQM: Uplink PESQ sentence index. Same meaning as PESQ Sentence DL (which see). AQM: Volume on downlink.
Currently used speech codec, e.g. EFR. AQM: The length of time it takes for the speech to travel from the Call Generator to the MTU and back to the Call Generator again. This element only appears in merged logfiles (see RA UM section 17.2).
SQI
20 ... 30 dBQ
Speech Quality Index. See DC UM chapter 28. The range depends on the speech codec used: HR (Half Rate): 20 ... 17 dBQ FR (Full Rate): 19 ... 22 dBQ EFR (Enhanced Full Rate): 20 ... 30 dBQ AMR: Dependent on codec mode. The maximum SQI values are as follows: 12.2 kbit/s: 30 dBQ 10.2 kbit/s: 28 dBQ 7.95 kbit/s: 28 dBQ 7.40 kbit/s: 27 dBQ 6.70 kbit/s: 27 dBQ 5.90 kbit/s: 24 dBQ 5.15 kbit/s: 21 dBQ 4.75 kbit/s: 19 dBQ Non-existent for GPRS (no voice data in packets).
196
Arg
* g
4.2.7.
Scan Data
For Sony Ericsson phones K600i/W600i and later, these elements are valid when C/A measurements are activated in the phone properties. See DC UM section 15.2.3.4.
IE Name Scanned Adjacent ARFCN Range/Unit See ARFCN BCCH, section 4.2.8.1 Arg 0 ... 63 * h+ Description C/A scanning: ARFCNs of adjacent channels. Attributes: 2: Channel at 400 kHz 1: Channel at 200 kHz +1: Channel at +200 kHz +2: Channel at +400 kHz
Argument: 0 means the channel adjacent to the first channel in the hopping list, etc. Scanned Adjacent ARFCN C0 See ARFCN BCCH, section 4.2.8.1 0 ... 63 h+ C/A scanning: ARFCNs used by current serving cell. BCCHs are shown in idle mode, TCHs in dedicated mode. Note that this element does not itself refer to an adjacent channel but to the C0. Argument: 0 means the first channel in the hopping list, etc.
197
Arg 0 ... 63
* h+
Description C/A scanning: Scanned signal strength of adjacent channels. Attributes: 2: Channel at 400 kHz 1: Channel at 200 kHz +1: Channel at +200 kHz +2: Channel at +400 kHz
Argument: 0 gives the RxLev of the channel adjacent to the first channel in the hopping list, etc. Scanned Adjacent RxLev C0 120 ... 10 dBm 0 ... 63 h+ C/A scanning: Scanned signal strength of the channels used by the current serving cell. That is, BCCHs in idle mode and TCHs in dedicated mode. Note that this element does not itself refer to an adjacent channel but to the C0. Argument: 0 gives the RxLev of the first channel in the hopping list, etc. Scanned ARFCN See ARFCN BCCH, section 4.2.8.1 0 ... 846 ARFCNs of scanned channels. Attributes: The attribute determines the sorting order. Channel order: Channels sorted by frequency (not ARFCN) in ascending order. Strongest: Channels sorted by descending signal strength. Weakest: Channels sorted by ascending signal strength.
Argument: The meaning of the argument depends on the attribute selected (see above).
198
Range/Unit Text
Description Frequency bands of scanned channels. Attributes, Argument: Works as for Scanned ARFCN.
Scanned BSIC
00 ... 77 (octal)
0 ... 846
00 ... 77 (octal)
Text
Names of scanned channels. Obtained only if both ARFCN and BSIC are scanned. Attributes, Argument: Works as for Scanned ARFCN.
0 ... 846
Number of channels currently scanned. C/I values for scanned channels. Attributes, Argument: Works as for Scanned ARFCN.
Scanned RxLev
0 ... 846
Received signal strength of scanned channels (GSM scan or RSSI scan). Attributes, Argument: Works as for Scanned ARFCN.
199
Description Received signal strength of scanned channels (GSM scan or RSSI scan). Argument: ARFCN.
4.2.8.
4.2.8.1.
Serving
Channel
Range/Unit GSM 850: 128 ... 251 P-GSM 900: 1 ... 124 E-GSM 900: 0 ... 124, 975 ... 1023 GSM 1800: 512 ... 885 GSM 1900: 512 ... 810 Arg * Description Absolute Radio Frequency Channel Number of Broadcast Control Channel.
ARFCN Current
In idle mode: Same as ARFCN BCCH. In dedicated mode: Same as ARFCN TCH. Not valid when frequency hopping is used.
ARFCN TCH
Absolute Radio Frequency Channel Number of Traffic Channel. Valid only in dedicated mode and only for channels where no frequency hopping is used.
200
IE Name BSIC
Arg
Cell Id
Cell Identity.
Cell Name
Text
Name of serving cell. Present only if a cell file is used. Calculated using a number of different algorithms: see Cell Name Algorithm.
1 ... 3
Indicates the input used by the cell name determination algorithm and (for values 2 and 3) the result of the cell search: 1: MCC, MNC, LAC, and CI used. 2: BSIC, ARFCN, and position information used. Unique cell found matching these parameters within a 35 km radius. 3: BSIC, ARFCN, and position information used. Several matching cells found within a 35 km radius, closest cell selected.
CGI
Cell Global Identity. Consists of Mobile Country Code, Mobile Network Code, Location Area Code and Cell Identity. Presented on the format MCC MNC LAC CI. Activity on channel: Signaling only, speech transmission, or data transmission.
Channel Mode
Text
201
Range/Unit Text
Arg
* g+ hs+
Description Channel type, also indicating which speech coder is used. For example, TCH/F + FACCH/F and SACCH/M, BCCH, or PDCH. Currently used ciphering (A5/1, A5/2, GEA/1, etc.), whether for circuit-switched or packetswitched. Frequency band of BCCH carrier, e.g. 850, 1900, 900E, 900R. Frequency band of current traffic channel or channels, e.g. 850, 1900, 900E, 900R. Use of frequency hopping (YES/NO). ARFCNs of the channels in the hopping frequency list, for example 1, 10, 19, 28. Hopping Sequence Number, indicating which hopping frequency list to use. Location Area Code.
Ciphering Algorithm
Text
Text
Text
Text Text
HSN
0 ... 63
LAC
MAIO
0 ... 63
Mobile Allocation Index Offset. Indicates where in the hopping frequency list to start. Valid only if frequency hopping is used. Mobile Country Code.
MCC
202
Arg
Description Mobile Network Code. May consist of two or three digits. Number of frequencies in hopping list.
0 ... 7
Number of subchannel used in SDCCH or TCH half-rate channel. Current training sequence code.
0 ... 7
4.2.8.2.
Interference
203
Range/Unit 5 ... 35 dB
Arg
Description C/I limit for codec change to higher bit rate, calculated from AMR Hysteresis and AMR Threshold. C/I limit for codec change to lower bit rate, calculated from AMR Hysteresis and AMR Threshold. Carrier over Adjacent. Calculated as (RxLev for serving cell) (Adjacent RxLev for 3), i.e. the adjacent channels frequency is 600 kHz below the serving cells. Invalid if frequency hopping is used.
5 ... 35 dB
C/A 3
As C/A 3 but with adjacent channel at 400 kHz, 200 kHz, +200 kHz, +400 kHz, and +600 kHz respectively. g+ hs+ h+ C/I values for all hopping channels in all used timeslots. The whole list is sorted by descending or ascending C/I. For Nokia phones, a single C/I value is obtained (snapshot from the channel used at the time of measurement). This value is found at argument 0 of this element. For PCTel scanners, one C/I value is obtained for each channel scanned. Attributes: Best: Channels sorted by descending C/I. Worst: Channels sorted by ascending C/I.
C/I
5 ... 35 dB
0 ... 511
(8641)
204
Range/Unit 5 ... 35 dB
C/I ARFCN
g+ hs+ h+ g hs h+
ARFCN list corresponding to the element C/I (which see). Attributes: See C/I. C/I for the worst channel in the hopping list for each used timeslot. Argument: 0 represents the first used timeslot (not TS 0), etc.
0 ... 7
5 ... 35 dB
0 ... 63
g+ hs+ hc+
C/I values (unsorted) for the channels in the hopping list. For multislot channels, the mean value across all used timeslots is given. Argument: 0 gives the C/I of the first channel in the hopping list, etc.
0 ... 63
h+
ARFCNs of the channels in the hopping list (see C/I Hopping List). Argument: 0 gives the ARFCN of the first channel in the hopping list, etc.
205
Range/Unit 5 ... 35 dB
Arg
Description C/I on the current BCCH. If frequency hopping is used, then if the BCCH is used as hopping frequency, report the C/I for that channel. If frequency hopping is not used, then if the BCCH is equal to the TCH, report its C/I. Invalid otherwise.
C/I Timeslot
0 ... 7
0 ... 511
(8641)
g hs h+
For multislot allocations: Timeslot list corresponding to the element C/I (which see). Attributes: See C/I.
0 ... 63
h+
C/A scanning: C/A values corresponding to Scanned Adjacent RxLev with attributes +1 and 1. Attributes: 1: Channel at 200 kHz +1: Channel at +200 kHz
Argument: 0 gives the ARFCN of the first channel in the hopping list, etc. Scanned C/A +/2 100 ... 100 dB 0 ... 63 h+ C/A scanning: C/A values corresponding to Scanned Adjacent RxLev with attributes +2 and 2. Attributes: 2: Channel at 400 kHz +2: Channel at +400 kHz
Argument: 0 gives the ARFCN of the first channel in the hopping list, etc.
206
4.2.8.3.
Measurement
Range/Unit 0 ... 26 % Arg * g hs Description Bit error rate, calculated taking DTX into account, i.e. the figure is based only on blocks actually transmitted. Valid for voice only. Bit error rate for each used timeslot. Valid for data services only. Argument: 0 represents the first used timeslot (not TS 0), etc.
BER/Timeslot
0 ... 26 %
0 ... 7
g hs
BLER/Timeslot
0 ... 100 %
0 ... 7
g hs
Block error rate for each timeslot used. Valid for data services only. Argument: 0 means the first used timeslot (not TS 0), etc.
C1
127 ... 127 dB 127 ... 127 dB 10 ... 100 GSM RxLev units or 120 ... 10 dBm
C2
Channel RxLev
Measured signal strength level for all channels. Argument = ARFCN. Note: Unlike RxLev Full/RxLev Sub, this element is also updated by scan reports. Current value of Downlink Signalling Counter (DSC). Valid only in idle mode.
0 ... 45
0 ... 45
Initial value of Downlink Signalling Counter (DSC). Valid only in idle mode.
207
Arg
* g
100
2 mandatory blocks are always sent using DTX: 1 TCH (with SID information) and 1 SACCH. Non-existent for packetswitched (no DTX). FER Actual 0 ... 100 % g hs Frame erasure rate, calculated taking DTX into account, i.e. the figure is based only on blocks actually transmitted. Valid for voice only. FER Full 0 ... 100 % Frame erasure rate, Full value. Calculated as:
number of erased blocks ---------------------------------------------------------------total number of blocks
100
A block is erased when the parity check (CRC) fails. FER Sub 0 ... 100 % 0 ... 3 Frame erasure rate, Sub value. For the calculation, see FER Full. g Type of GPRS connection on downlink: 0: Dynamic Allocation 1: Extended Dynamic Allocation 2: Fixed Allocation, not half duplex mode 3: Fixed Allocation, half duplex mode MAC Mode UL 0 ... 3 g Type of GPRS connection on uplink. See MAC Mode DL.
MAC Mode DL
208
Arg
Description Phone transmit power ordered by the base station, mapped to a number between 0 and 31 according to the tables in 3GPP 45.005, section 4.1.1. Valid only in dedicated mode. Phone transmit power in dBm. Valid only in dedicated mode.
MS Tx Power
GSM 850: 5 ... 39 GSM 900: 5 ... 39 GSM 1800: 0 ... 36 GSM 1900: 0 ... 33 dBm
0 ... 64
Current value of Radio Link Timeout counter. Uses the leaky bucket principle. Each decoded block increases the counter by 1 (if it is not already at max) and each failed block decreases the counter by 2. The call is terminated when the counter drops to 0. Valid only in dedicated mode.
4, 8, ..., 64
Initial value of Radio Link Timeout counter. Valid only in dedicated mode.
RxLev Full
209
Arg
Description Same as RxLev Full but valid only when the phone is in idle, dedicated, packet idle, or packet dedicated mode. Not valid when in limited service or no service mode. Received signal strength (Sub value).
RxLev Sub
Same as RxLev Sub but valid only when the phone is in idle, dedicated, packet idle, or packet dedicated mode. Not valid when in limited service or no service mode. Received signal quality (Full value), expressed as the bit error rate in percent or calculated from the bit error rate according to the table in 3GPP 45.008, section 8.2.4. Received signal quality (Sub value), expressed as the bit error rate in percent or calculated from the bit error rate according to the table in 3GPP 45.008, section 8.2.4.
RxQual Full
RxQual Sub
210
Arg 0 ... 63
* h+
Description Signal strength of each channel in the hopping list. This element thus gives more information than RxLev, which is an average over all channels in the hopping list. Argument: 0 means the first channel in the hopping list, etc.
Signal strength on the current BCCH. Especially useful for obtaining a correct measure of the cell size when frequency hopping is used and power control is applied to the TCHs. The following steps are used to find a value for the element: 1. Neighbor list. If the BCCH frequency is in the neighbor list, report its signal strength. 2. Hopping list. If the BCCH is used as hopping frequency (in dedicated mode), report its signal strength. 3. Idle mode. If the phone is in idle mode, report RxLev (dBm). If frequency hopping is not used, step 2 becomes If BCCH = TCH .... Invalid if no value is found in any of the above steps.
TA
Timing Advance. Valid only in dedicated mode. For the significance of the parameter value, see 3GPP 45.010. Timeslot used for current call. Valid only in dedicated mode.
Timeslot
0 ... 7
211
4.2.9.
WCDMA Parameters
34 ... 0 dB
1 ... 32
WCDMA Neighbor SC
WCDMA Neighbors No of
212
4.3.
Notes on Quantities Denoting Signal Power See section 3.2, page 58.
4.3.1.
Active Set
1 ... 6 1 ... 6
4.3.2.
Data
213
IE Name PDP Address PDP Context Time PDP Contexts Active PDP Delay Class PDP LLC SAPI PDP Mean Throughput PDP NSAPI PDP Peak Throughput PDP Precedence Class PDP Radio Priority PDP Reliability Class
Range/Unit Text 0 ... 60000 ms 0 ... 11 Text 3 ... 11 Text 5 ... 15 Text Text
Arg 1 ... 11
Description User address (IPv4/IPv6). Time from PDP Context Activation Request to PDP Context Activation Accept. Number of active PDP contexts. Delay class as defined by subscription. LLC Service Access Point Identifier. Mean throughput as defined by subscription. Network SAPI (Service Access Point Identifier). Peak throughput as defined by subscription. Precedence class as defined by subscription. Radio priority level as defined by subscription. Reliability class as defined by subscription.
Text Text
1 ... 11 1 ... 11
4.3.3.
Finger Info
The Rake fingers are not sorted by signal strength; they come in the order they are reported. Rake fingers are reported separately for each UMTS frequency. The Motorola E1000 may report finger measurements on a number of different channels (see the element Finger Position Type); the other devices that support finger measurements always report them on the CPICH. The Finger and Finger Position series of elements contain the same data. The latter series contains arrays of size 2560 corresponding to the sequence
214
of chips in a radio frame timeslot, with the received finger information positioned at the correct indices. These elements are provided for bar chart plotting. The Finger Slot Position element is of course not needed in the Finger Position series and is consequently absent from it. Two arguments are used. The first represents the UMTS frequency; the second represents either the Rake finger number (Finger series) or the chip index (Finger Position series).
IE Name Finger Ec/No Finger No of Finger RSCP Finger RSSI Finger SC Finger Slot Finger Slot Position Finger Type Finger UARFCN Range/Unit 34 ... 0 dB 0 ... 48 140 ... 15 dBm 130 ... 20 dBm 0 ... 511 0 ... 15 1 ... 2560 Text 0 ... 16383 (frequency band dependent) 0 ... 511 34 ... 0 dB 140 ... 15 dBm Arg 1 ... 12; 1 ... 48 1 ... 12 1 ... 12; 1 ... 48 1 ... 12; 1 ... 48 1 ... 12; 1 ... 48 1 ... 12; 1 ... 48 1 ... 12; 1 ... 48 1 ... 12; 1 ... 48 1 ... 12; 1 ... 48 Description Ec/No for each Rake finger. Total number of Rake fingers. RSCP for each Rake finger. RSSI for each Rake finger. Scrambling code for each Rake finger. Radio frame timeslot index for each Rake finger. Position (chip index) of each Rake finger within the radio frame timeslot. Type of channel on which each Rake finger is reported (e.g. CPICH). UARFCN for each Rake finger.
1 ... 12; 1 ... 2560 1 ... 12; 1 ... 2560 1 ... 12; 1 ... 2560
Same as Finger SC (see general remarks). Same as Finger Ec/No (see general remarks). Same as Finger RSCP (see general remarks).
215
IE Name Finger Position RSSI Finger Position Slot Finger Position Type Finger Position UARFCN
Range/Unit 130 ... 20 dBm 0 ... 15 Text 0 ... 16383 (frequency band dependent)
Arg
1 ... 12; 1 ... 2560 1 ... 12; 1 ... 2560 1 ... 12; 1 ... 2560 1 ... 12; 1 ... 2560
Description Same as Finger RSSI (see general remarks). Same as Finger Slot (see general remarks). Same as Finger Type (see general remarks). Same as Finger UARFCN (see general remarks).
4.3.4.
GSM Parameters
Range/Unit See section 4.2 under ARFCN BCCH Text Arg 1 ... 32 Description ARFCNs of measured GSM neighbors. Argument: 1 gives the neighbor with the highest signal strength, etc. 1 ... 32 Base Station Identity Codes (in text format) of measured GSM neighbors. Argument: See GSM Neigh ARFCN.
1 ... 32
Number of measured GSM neighbors. Received signal strength of measured GSM neighbors. Argument: See GSM Neigh ARFCN.
216
4.3.5.
Handover
Range/Unit 0, 1 Arg Description Use of compressed mode. 0: False 1: True 0 ... 6 or Text Type of latest handover. 0: Unknown (e.g. because no cell file loaded) 1: Soft 2: Softer 3: Hard 4: Handover to UTRAN 5: Handover from UTRAN 6: GSM 1 ... 10 Event criteria governing when the UE should send inter-frequency measurement reports. Argument: One argument for each event criterion.
HO Event Type
Text
Text
1 ... 10
Names of events governing sending of inter-frequency measurement reports by the UE. The events extracted to this element are e2a, e2d, and e2f. Other inter-frequency events are not extracted. Argument: One argument for each event criterion. There may be multiple criteria for the same event.
Text
1 ... 5
Event criteria governing when the UE should send inter-RAT measurement reports. Argument: One argument for each event criterion.
217
Range/Unit Text
Arg 1 ... 5
Description Names of events governing sending of inter-RAT measurement reports by the UE. The only event extracted to this element is e3a. Other inter-RAT events are not extracted. Argument: One argument for each event criterion. There may be multiple criteria for the same event.
Intra-freq Cells
Text
Cells on which the UE has been ordered to perform intra-frequency measurements. Event criteria governing when the UE should send intra-frequency measurement reports. Argument: One argument for each event criterion.
Text
1 ... 10
Text
1 ... 10
Names of events governing sending of intra-frequency measurement reports by the UE. The events extracted to this element are e1a, e1b, e1c, and e1d. Other intra-frequency events are not extracted. Argument: One argument for each event criterion. There may be multiple criteria for the same event.
0 ... 50
0 ... 3600
Number of radio link events (both failures and successes) over the last arg seconds, where arg is the value of the argument. Regarding the events, see section 7.2. Argument: See above. Argument = 0 means that the events are counted from the beginning of the logfile.
218
Arg
Description Soft handover success rate. Calculated as: (# add + # rem + # repl) / # all where add = Radio Link Addition events rem = Radio Link Removal events repl = Radio Link Replacement events all = All radio link events, including failures Regarding the events, see section 7.2.
0 ... 100 %
A measure of the amount of softer handover. Calculated as: # softer / (# softer + # soft) where softer = Radio link event indicating success occurs while in softer handover (and with more than one member in active set) soft = Radio link event indicating success occurs while in soft handover (and with more than one member in active set) A radio link event is one of Radio Link Addition, Radio Link Removal, and Radio Link Replacement. Regarding the events, see section 7.2. Requires that a cell file has been loaded (otherwise the element is invalid).
219
Arg
Description Soft handover state. 0: Unknown (no cell data loaded) 1: Soft handover 2: Softer handover Requires that a cell file has been loaded (otherwise the value will always be = 0). Invalid when AS No of Members < 2.
4.3.6.
HSDPA
Range/Unit 0 ... 100 % 0 ... 100 % 0 ... 30 See Description Arg Description Use of 16-QAM as modulation method, expressed as a percentage of time. Use of 64-QAM as modulation method, expressed as a percentage of time. The maximum value of the CQI (Channel Quality Indicator) during the latest reporting period. The definition of the CQI values is given in 3GPP 25.214, section 6A.2.
HS CQI (Median)
0 ... 30
The median CQI value during the latest reporting period. Compare HS CQI (Max).
HS CQI (Min)
0 ... 30
The minimum CQI value during the latest reporting period. Compare HS CQI (Max).
220
Arg
Description CQI feedback cycle, controlling how often the UE transmits new CQI information on the uplink (see 3GPP 25.214, section 6A.1.2). A value of zero means that the UE shall not transmit any CQI information. CQI repetition factor, controlling how often the UE repeats CQI information on the uplink (see 3GPP 25.214, section 6A.1.2). ACK / (NACK + ACK) ratio on the HSDSCH. Block error rate on the HS-DSCH for first transmission. Residual block error rate on the HSDSCH (decoding unsuccessful after maximum number of retransmissions). Same as HS-DSCH BLER Residual but for each active HARQ process separately. Argument: HARQ process index.
HS CQI Repetition Factor HS-DSCH ACK Rate HS-DSCH BLER 1st HS-DSCH BLER Residual HS-DSCH BLER Residual Per Process
0 ... 15
0 ... 16
HS-DSCH DTX Rate HS-DSCH Error Blocks 1st No Of HS-DSCH Error Blocks Residual No Of HS-DSCH Error Blocks Residual No Of Per Process
DTX rate on the HS-DSCH. Number of block errors on the HSDSCH (first transmission). Number of residual error blocks on the HS-DSCH (decoding unsuccessful after maximum number of retransmissions). Same as HS-DSCH Error Blocks Residual No Of but for each active HARQ process separately. Argument: HARQ process index.
0 ... 20000
0 ... 20000
0 ... 16
221
IE Name HS-DSCH HARQ Processes No Of HS-DSCH NACK Rate HS-DSCH New Transmission Rate Per Process HS-DSCH Retransmission Rate HS-DSCH Retransmission Rate Per Process HS-DSCH Retransmissions HS-DSCH Throughput HS-DSCH Throughput Per Process HS H-RNTI
Range/Unit 0 ... 16
Arg
Description Number of active HARQ (Hybrid Automatic Repeat Request) processes on the HS-DSCH. NACK / (NACK + ACK) ratio on the HS-DSCH. New transmission rate on the HSDSCH for each active HARQ process. Argument: HARQ process index.
0 ... 16
0 ... 16
Same as HS-DSCH Retransmission Rate but for each active HARQ process separately. Argument: HARQ process index.
0 ... 20000
Number of retransmitted blocks on the HS-DSCH. Throughput on the HS-DSCH. Same as HS-DSCH Throughput but for each active HARQ process separately. Argument: HARQ process index.
0 ... 16
0 ... 65535
222
Arg 1 ... 15
Description Distribution of channelization code usage on the HS-PDSCH for the whole of the HSDPA session. This element does not take DTX into account, so that values are computed as percentages of all blocks, whether used or unused. Argument: Channelization code index.
0 ... 100 %
1 ... 15
Current distribution of channelization code usage on the HS-PDSCH. This element takes DTX into account, so that values are computed as percentages of the total number of used blocks. Argument: Channelization code index.
Calculated as: (Average requested transport block size based on CQI) / (2 ms) Calculated as: (Average transport block size in TTIs where data is transferred) / (2 ms) (Only TTIs in which data is actually received are considered in the throughput calculation.)
Calculated as: (Average transport block size counting all TTIs) / (2 ms) (All TTIs, also those in which no data is received, are included in the throughput calculation.)
0 ... 16
Same as HS Phy Served Throughput but for each active HARQ process separately. Argument: HARQ process index.
223
Arg
Description Use of QPSK as modulation method, expressed as a percentage of time. Channelization codes used on the HSSCCH, arranged in ascending order. Argument: Channelization code index.
1 ... 8
HS-SCCH Channelisation Codes No Of HS-SCCH Channelisation Codes HS-SCCH Decode Success Rate
0 ... 8
Number of channelization codes used on the HS-SCCH. List of HS-SCCH channelization codes in text format. Decode success rate on the HSSCCH. For the decoding to count as a success, both the first and the second parts must have been completed successfully. The scrambling code index of the HSPA serving cell. Name of HSPA serving cell. Requires cell file. Indicates whether the session is an HSDPA or HSUPA session (as opposed to an R99 session). 0: No 1: Yes
Text
0 ... 100 %
0 ... 65535
1 ... 31
Block counts for HSPA transport block sizes currently in use. Attributes: Accumulated: Block counts are for the whole of the current session. Current: Block counts are for the latest report period.
224
Description Block counts for all possible HSPA transport block sizes, accumulated over the current session. Argument: The transport block size itself (not an index).
1 ... 31
Transport block sizes on the HSDSCH. Argument: Transport block size index.
0 ... 31
4.3.7.
HSUPA
Range/Unit 0 ... 1000 Arg Description Average value of serving grant (maximum allowed E-DPDCH/EDPCCH power ratio). Average value of serving grant index.
IE Name HS UL Average Serving Grant HS UL Average Serving Grant Index HS UL Average TBS HS UL Average TBS / TBS Max E-TFCI
0 ... 40
Average transport block size on EDCH. Average value of: (transport block size on E-DCH) divided by (maximum transport block size on E-DCH as dictated by current E-TFCI). This is a measure of serving grant utilization. Block error rate on the E-DCH for first transmission. Residual block error rate on the EDCH (decoding unsuccessful after maximum number of retransmissions).
225
IE Name HS UL Buffer Limited Tx Rate HS UL DTX Rate HS UL E-DCH Throughput HS UL Error Blocks No Of
Range/Unit 0 ... 100 % 0 ... 100 % 0 ... 80000 kbit/s 0 ... 1000
Arg
Description Percentage of time the transmission on the E-DCH was buffer limited. Percentage of TTIs where nothing was sent on the E-DPCCH/E-DPDCH. Throughput on the E-DCH. Number of block errors for the first (second, third, fourth) transmission on the E-DCH. The sequence number of the transmission is specified by the attribute. Attributes: 1st ... 4th representing the first, second, third, and fourth transmission respectively.
HS UL Error Blocks Residual No Of HS UL Happy Rate HS UL HICH ACK Rate HS UL HICH NACK Rate HS UL New Transmission Rate HS UL NonServing Cells No Of HS UL NonServing Combined ERGCH Down
0 ... 1000
Number of residual block errors on the E-DCH after maximum number of retransmissions. Percentage of TTIs where the UE was happy. ACK rate on the E-HICH (HARQ Acknowledgement Indicator Channel). NACK rate on the E-HICH. Number of new transmissions on EDPCCH/E-DPDCH divided by the number of TTIs. Number of non-serving cells in E-DCH active set. Number of times a non-serving cell in the E-DCH active set was ordered to lower its transmit power (relative grant = Down).
0 ... 100
226
IE Name HS UL Number of TTIs HS UL Power Limited Tx Rate HS UL Retransmission Rate HS UL Serving Grant Limited Tx Rate HS UL Successful EAGCH Rate (All TTIs) HS UL Successful First Tx Rate
Range/Unit 0 ... 100 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 100 %
Arg
Description Number of TTIs (transmission time intervals) in log report. Percentage of time the transmission was limited by the available Tx power. Number of retransmissions on EDPCCH/E-DPDCH divided by the number of TTIs. Percentage of time the transmission was limited by the current serving grant. Percentage of TTIs where the UE received an absolute grant on the EAGCH. Percentage of TTIs where the first transmission was successful.
0 ... 100 %
4.3.8.
DPCCH interference signal code power on downlink. DPCCH received signal code power on downlink.
227
Range/Unit Text
Arg 1 ... 4
Description Radio Link Control (Acknowledged Mode): Type of downlink logical channel, e.g. DCCH. Argument: Logical channel index.
0 ... 100 %
1 ... 4
Radio Link Control (Acknowledged Mode, downlink): PDU retransmission percentage. Calculated as:
no. of NACKed PDUs 100 -------------------------------------------------------------------------total no. of PDUs
Argument: Logical channel index. RLC AM DL PDU Throughput 0 ... 80000 kbit/s 1 ... 4 Radio Link Control PDU throughput (Acknowledged Mode, downlink), counting both control PDUs and AM PDUs. Since the PDU throughput includes RLC headers, it will be slightly higher than the SDU throughput where such headers are absent. Argument: Logical channel index. RLC AM DL SDU Throughput RLC AM UL Log Ch Type 0 ... 80000 kbit/s 1 ... 4 Radio Link Control SDU throughput (Acknowledged Mode, downlink). Argument: Logical channel index. Text 1 ... 4 Radio Link Control (Acknowledged Mode): Type of uplink logical channel, e.g. DCCH. Argument: Logical channel index. RLC AM UL PDU Retransm 0 ... 100 % 1 ... 4 Radio Link Control (Acknowledged Mode, uplink): PDU retransmission percentage. Calculated as:
no. of NACKed PDUs 100 -------------------------------------------------------------------------total no. of PDUs
228
Arg 1 ... 4
Description Radio Link Control PDU throughput (Acknowledged Mode, uplink), counting both control PDUs and AM PDUs. Since the PDU throughput includes RLC headers, it will be slightly higher than the SDU throughput where such headers are absent. Argument: Logical channel index.
1 ... 4
Radio Link Control SDU throughput (Acknowledged Mode, uplink). Argument: Logical channel index.
1 ... 32
Downlink RLC entity data mode: Transparent Mode, Unacknowledged Mode, or Acknowledged Mode. Argument: RLC entity.
1 ... 32
1 ... 32
Total number of RLC entities on uplink and downlink. Uplink RLC entity data mode: Transparent Mode, Unacknowledged Mode, or Acknowledged Mode. Argument: RLC entity.
0 ... 80000 kbit/s 0 ... 80000 kbit/s 0 ... 80000 kbit/s 1 ... 512
1 ... 32
Highest downlink throughput for all RLC entities/transport channels. Highest uplink throughput for all RLC entities/transport channels. Spreading factor on downlink.
229
Arg 1 ... 32
Description Spreading factor on uplink. Block error rate on each downlink transport channel (DCH only) in percent. See 3GPP 25.215, section 5.1.6. Compare Trsp Ch BLER, DL (Log). Argument: Transport channel index.
1 ... 32
Block error rate on each downlink transport channel (DCH only), converted to logarithmic value. Regarding the conversion, see 3GPP 25.331, section 10.3.5.10. Argument: Transport channel index. Note: Nokia UEs do not deliver separate values for each transport channel, but only an average over all of them (arg = 1).
Block error rate on the worst downlink transport channel (DCH only) in percent. Block error rate target for each downlink transport channel (DCH only) in percent. Argument: Transport channel index.
1 ... 32
Trsp Ch Direction
Text: UL or DL
1 ... 32
Transmission direction of each transport channel: uplink or downlink. Argument: Transport channel index.
Trsp Ch Id
1 ... 32
1 ... 32
Identity of each transport channel. The channel type (DCH, RACH, or FACH) is indicated by the element Trsp Ch Type. Argument: Transport channel index.
Trsp Ch No of DL
0 ... 32
230
Arg 1 ... 32
Description Number of uplink transport channels. Total number of erroneous blocks on each transport channel. (The number of reports over which this is summed varies between phones.) Compare Trsp Ch BLER, DL (Log). Argument: Transport channel index.
0 ... 4095
1 ... 32
Number of blocks received on each transport channel. (The number of reports over which this is summed varies between phones.) Argument: Transport channel index.
Trsp Ch Throughput DL
1 ... 32
Total downlink throughput on all transport channels. Argument: Transport channel index.
1 ... 32
Total uplink throughput on all transport channels. Argument: Transport channel index.
Text
1 ... 32
Text
1 ... 32
231
4.3.9.
MS Behavior
Range/Unit Num: 0 ... 63 or Text Arg Description BLER Target value set on phone property page (DC UM section 15.2.3.14), overriding BLER target set by network. Use of cell barring related functions in phone. See DC UM sections 15.2.3.13, 15.3.2.3, and 15.4.2.2. Indicates whether the UE behavior has been changed from the default. Empty string: No modification of UE behavior B: Modification of UE behavior in network (information elements BLER Target Control, RAT Control) C: Modification of UE reselection behavior: (information elements Cell Barred Control, Sector Control) Combinations of these letters may appear.
RAT Control
Num: 0 ... 3
Use of Lock to RAT function in UE. 0: Lock to RAT disabled 1: Locked to GSM 900/1800 2: Locked to GSM 850/1900 3: Locked to WCDMA
Text
Use of Lock to RAT function in UE. Blank when no lock is engaged; Active when lock to RAT has been activated. Use of Lock to Sector function in UE in idle mode: 0: Lock to Sector disabled 1: Lock to Sector enabled
Sector Control
Num: 0, 1 or Text
232
4.3.10.
Neighbors
Range/Unit Text Arg 1 ... 6 Description Cell name of each detected neighbor. Requires cell file. Argument: Neighbor identity.
34 ... 0 dB
1 ... 6
1 ... 6
CPICH received signal code power of each detected neighbor. Argument: Neighbor identity.
Det Neigh CPICH TxPower Det Neigh No of Members Det Neigh Pathloss
31 ... 50 dBm
1 ... 6
1 ... 6
Number of detected neighbors. Pathloss of each detected neighbor. Calculated as Primary CPICH Tx Power CPICH RSCP. Argument: Neighbor identity.
Det Neigh SC
0 ... 511
1 ... 6
1 ... 6
1 ... 6
Cell name of each monitored neighbor. Requires cell file. Argument: Neighbor identity.
233
Range/Unit 34 ... 0 dB
Arg 1 ... 6
1 ... 6
CPICH received signal code power of each monitored neighbor. Argument: Neighbor identity.
Mon Neigh CPICH TxPower Mon Neigh No of Members Mon Neigh Pathloss
31 ... 50 dBm
1 ... 6
1 ... 6
Number of monitored neighbors. Pathloss of each monitored neighbor. Calculated as Primary CPICH Tx Power CPICH RSCP. Argument: Neighbor identity.
Mon Neigh SC
0 ... 511
1 ... 6
1 ... 6
1 ... 6
Cell names of neighbors (monitored as well as detected) sorted by signal strength in descending order. Requires cell file. Argument: 1 is the strongest neighbor, etc.
34 ... 0 dB
1 ... 6
CPICH Ec/No of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
234
Arg 1 ... 6
Description CPICH RSCP of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
Str Neigh SC
0 ... 511
1 ... 6
Scrambling codes of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
3 ... 4
1 ... 6
Types of neighbors (monitored as well as detected) sorted by signal strength in descending order. The types are: 3: Monitored neighbor 4: Detected neighbor Argument: 1 is the strongest neighbor, etc.
1 ... 6
CPICH UARFCNs of neighbors (monitored as well as detected) sorted by signal strength in descending order. Argument: 1 is the strongest neighbor, etc.
4.3.11.
Network Parameters
Range/Unit 000 ... 999 000 ... 999 Arg Description Mobile Country Code. Mobile Network Code. May consist of two or three digits.
4.3.12.
Quality Measurement
The Frequent AQM elements, uplink and downlink scores, only appear in merged logfiles (see RA UM section 17.2).
235
Uplink PESQ scores likewise only appear in merged logfiles. Downlink PESQ scores, as well as the remaining AQM measurements (all other elements prefixed with PESQ below), appear in merged as well as unmerged logfiles. However, prior to merging, all such data lags behind other data in the logfile. See RA UM section 17.2.2.
IE Name AMR Codec Name Range/Unit Text Arg 1 ... 8 Description Names of AMR codecs. Argument: Identifies the AMR codec. 1: 12.2 kbit/s 2: 10.2 kbit/s 3: 7.95 kbit/s 4: 7.40 kbit/s 5: 6.70 kbit/s 6: 5.90 kbit/s 7: 5.15 kbit/s 8: 4.75 kbit/s AMR Codec Usage (DL) 0 ... 100 % 1 ... 8 Current distribution of AMR codec usage on downlink. Argument: See AMR Codec Name. AMR Codec Usage (UL) 0 ... 100 % 1 ... 8 Current distribution of AMR codec usage on uplink. Argument: See AMR Codec Name. Frequent AQM elements PESQ elements Speech Path Delay See the description (cellular technology independent) under GSM, section 4.2.6. See the description (cellular technology independent) under GSM, section 4.2.6. See the description (cellular technology independent) under GSM, section 4.2.6.
236
IE Name SQI
Arg
Description Speech Quality Index for WCDMA. The range is different depending on the AMR speech codec mode. The maximum SQI values are as follows: 12.2 kbit/s: 30 dBQ 10.2 kbit/s: 28 dBQ 7.95 kbit/s: 28 dBQ 7.40 kbit/s: 27 dBQ 6.70 kbit/s: 27 dBQ 5.90 kbit/s: 24 dBQ 5.15 kbit/s: 21 dBQ 4.75 kbit/s: 19 dBQ
SQI expressed on the MOS scale. See DC UM chapter 28. Video Telephony Quality Index; see DC UM chapter 30.
4.3.13.
Radio Measurement
Range/Unit 0 ... 100 % Arg Description Calculated as: # ends / (# blocks + # drops + # ends) where blocks = Blocked Call events drops = Dropped Call events ends = Call End events Only events occurring in WCDMA mode are counted. Regarding the events, see section 7.2.
DTX Rate DL
0 ... 100 %
237
Range/Unit 1, 0, 1
Arg
Description Inner loop power control indication on downlink. Based on recent history of power control decisions: The value 1 means that the power has been adjusted predominantly downward. The value 0 means that the upward and downward power adjustments have canceled out. The value +1 means that the power has been adjusted predominantly upward.
Power Control Indication UL RACH Initial TX RACH Max Preambles RACH Message TX RACH Transmitted Preambles RB Setup UL DPCH SC RRC Connection Reject Cause
1, 0, 1
Inner loop power control indication on uplink. Works the same way as Power Control Indication DL, which see. Transmit power of first RACH preamble in dBm. Maximum number of preambles in one preamble ramping cycle. Transmit power of last RACH preamble in dBm. Number of preambles used in this preamble ramping cycle. The scrambling code of the uplink Dedicated Physical Channel. Cause for rejection of RRC connection establishment request. 0: Congestion 1: Unspecified See 3GPP 25.331, section 10.3.3.31.
238
Range/Unit 0 ... 16 s
Arg
Description The time the UE has to wait before repeating the rejected RRC procedure. See 3GPP 25.331, section 10.3.3.50.
0 ... 5 or Text
State of RRC protocol: 0: No service 1: Idle mode 2: Connected_Cell_FACH 3: Connected_Cell_DCH 4: Connected_Cell_PCH 5: Connected_URA_PCH The state is set to idle when the UE registers, and the information element is then updated each time the state changes. See 3GPP 25.331, chapter 7.
SIR
20 ... 30 dB 20 ... 30 dB 60 ... 44 dBm 60 ... 44 dBm 110 ... 70 dBm 130 ... 20 dBm
Signal-to-interference ratio, measured on DPCCH. See 3GPP 25.215, section 5.2.2. SIR target governing SIR. UE initial transmit power in dBm.
SIR Target UE Initial Transmit Power UE TxPower UL Interference Serving UTRA Carrier RSSI
UE transmit power in dBm. Valid only in connected mode. Interference on uplink, extracted from SIB type 7. Total energy measured by the UE within the downlink bandwidth.
4.3.14.
SAN
These elements are presented in the Serving/Active Set + Neighbors status window.
239
The argument, where present, indicates the row in this window. In Cell_DCH mode, the active set is on top (max 4 rows), whereas in other modes the serving cell is found on row 1. In either case the neighbors follow directly beneath.
IE Name SAN Cell Id SAN Cell Id (CI Part) Range/Unit 0 ... 228 1 Num: 0 ... 216 1 or Text (hex): 0000 ... FFFF SAN Cell Id (RNC Part) Num: 0 ... 212 1 or Text (hex): 000 ... FFF SAN Cell Name SAN Cell Type Text Num: 1 ... 4 or Text 1 ... 38 1 ... 38 Name of each cell listed. Requires cell file. Type of cell for each cell listed. Requires cell file. 1 or SC: Serving cell 2 or AS: Active set member 3 or MN: Monitored neighbor 4 or DN: Detected neighbor SAN CPICH Ec/No SAN CPICH RSCP SAN HS Cell Type 34 ... 0 dB 140 ... 15 dBm Num: 0 ... 1 or Text 1 ... 38 1 ... 38 1 ... 38 CPICH Ec/No for each cell listed. CPICH RSCP for each cell listed. Cell type for each cell in HSPA active set. 0/N-SC: Non-serving cell 1/SC: Serving cell 1 ... 38 RNC part of SAN Cell Id: bits 0 through 11. Arg 1 ... 38 1 ... 38 Description Cell identity of each cell listed. Cell Identity part of SAN Cell Id: bits 12 through 27.
240
Range/Unit 0 ... 38 30 ... 165 dB 31 ... 50 dBm 0 ... 511 410 ... 10850 (frequency band dependent)
Arg 1 ... 38
Description Total number of cells listed. Pathloss for each cell listed. Calculated as Primary CPICH Tx Power CPICH RSCP. Primary CPICH transmit power for each cell listed. Scrambling code for each cell listed. Downlink UARFCN for each cell listed.
1 ... 38
1 ... 38 1 ... 38
SAN URA Id
0 ... 228 1
1 ... 38
4.3.15.
Scan Data
See DC UM for further information on the following topics: Pilot scanning: DC UM section 10.2 SCH timeslot scanning: DC UM section 10.3 RSSI (CW) scanning: DC UM section 10.4 Spectrum analysis: DC UM section 10.5 Network search: DC UM section 10.6
IE Name CW Sc No of UARFCNs Range/Unit 0 ... 255 Arg Description RSSI scanning: Number of UARFCNs scanned.
241
IE Name CW Sc RSSI
Description RSSI scanning: RSSI of UARFCNs scanned. Argument: The channels are sorted by ascending UARFCN. The argument 1 gives the channel with the lowest UARFCN.
CW Sc UARFCN
1 ... 255
RSSI scanning: UARFCNs of channels scanned, sorted in ascending order. Argument: 0 gives the first channel currently scanned, 1 the second, etc.
0 ... 800
Network scanning: The number of UARFCNs scanned. Network scanning: Scrambling code detected on each UARFCN scanned. Argument: Position in list of scanned UARFCNs.
0 ... 511
1 ... 800
1 ... 800
242
IE Name Other/Own
Range/Unit 0 ... 10 dB
Description Pilot scanning: Estimated ratio between polluting signal power and desired signal power on a CPICH control channel, based on the assumption that the active set has at most n members, where n is given as an attribute. Attributes: The maximum number of members assumed for the active set: 1, 2, 3, or 4. Argument 1: UMTS frequency (UARFCNs sorted in ascending order). Argument 2: Power threshold (in dB) relative to the power of the strongest scrambling code; used to identify possible active set members. See DC UM section 10.2.7 for a full description.
Poss No of AS Members
0 ... 10
Pilot scanning: The estimated number of possible members in the active set. Argument 1: UMTS frequency (UARFCNs sorted in ascending order). Argument 2: Power threshold (in dB) relative to the power of the strongest scrambling code; used to identify possible active set members. See DC UM section 10.2.7 for a full description.
243
Range/Unit
Arg
Description
The attributes for these elements have the following meanings: Not sorted: Scrambling codes are ordered by index (no ranking). Lowest index first. Strongest: Scrambling codes are ranked by Aggr Ec/Io in descending order, for each scanned UMTS frequency separately. Weakest: Scrambling codes are ranked by Aggr Ec/Io in ascending order, for each scanned UMTS frequency separately. Best (among all frequencies): Scrambling codes from all scanned UMTS frequencies are ranked by descending Aggr Ec/Io in a single list. The first argument is always 1 in this case. Argument 1: UMTS frequency. Frequencies are ordered by ascending UARFCN. This argument is not used with the attribute Best (see above). Argument 2: Scrambling code. Scrambling codes are ordered as specified by the chosen attribute (see above). Some Sc elements are not differentiated for scrambling codes and therefore lack this argument. 10 ... 21 dB 1 ... 4; 1 ... 512 Pilot scanning: The aggregate code power of the scrambling code (Eb, energy per bit) relative to the total signal power in the channel (Io). See also general remarks above.
Sc Aggr Eb/Io
Sc Aggr Ec
Pilot scanning: The aggregate code power (energy per chip) of each scanned scrambling code. The aggregate code power is a measure of the total signal power (distributed around the main peak due to multipath propagation) that is above the PN threshold. See also general remarks above.
244
Range/Unit 30 ... 0 dB
Description Pilot scanning: The aggregate code power of the scrambling code (Ec, energy per chip) relative to the total signal power in the channel (Io). See also general remarks above.
Sc Aggr-Peak Ec
0 ... 90 dB
Pilot scanning: The difference between the aggregate code power and peak code power. See also general remarks above.
Sc Cell Name
Text
Pilot scanning: Deduced name of the cell that uses each scanned scrambling code. The algorithm determining the cell name takes as input the SC number, the UARFCN, and the position reported. It searches the cell file for cells with matching SC number and UARFCN within a 50 km radius. If multiple matches are found, the cell closest to the position is selected. If no positioning data is available, the information element will still be presented, but the cell names may then of course be wrong. The algorithm in this case simply picks the first cell in the cell file with matching SC number and UARFCN. Requires cell file and positioning. See also general remarks above.
245
Range/Unit 1 ... 3
Description Pilot scanning: Categorization of the cells that use the scanned scrambling codes. 1: The cell with the strongest Aggr Ec. 2: All neighbors of the 1 cell, as indicated by the cell file. 3: All other cells. If the Best attribute is set, this categorization is still applied for each UMTS frequency, so there will be one 1 with associated 2s for each frequency. Requires cell file and positioning. See also general remarks above.
Sc Delay Spread
Pilot scanning: Time in chips between the first and last Ec/Io peak that is above the PN threshold. This is a measure of the signal spreading due to multipath propagation. See also general remarks above.
Sc Intra-freq Cells
Text
1 ... 12
Pilot scanning: Neighbor list for the scrambling code with the highest Aggr Ec/Io. Obtained from SIB. Given as a comma-separated string of scrambling codes, e.g. 1, 3, 5.
Sc Io
1 ... 12
Pilot scanning: The total signal power in the channel. See also general remarks above.
Sc No of SCs
0 ... 512
1 ... 12
Pilot scanning: The number of scrambling codes scanned. See also general remarks above.
246
Range/Unit 10 ... 21 dB
Description Pilot scanning: The peak code power of each scanned scrambling code (Eb, energy per bit) relative to the total signal power in the channel (Io), i.e. the difference between them in dB. See also general remarks above.
Sc Peak Ec (dBm)
Pilot scanning: The peak code power of each scanned scrambling code (Ec, energy per chip) in dBm. See also general remarks above.
30 ... 0 dB
Pilot scanning: The peak code power of each scanned scrambling code (Ec, energy per chip) relative to the total signal power in the channel (Io), i.e. the difference between them in dB. See also general remarks above.
Sc P-SCH Ec (dBm)
The peak code power of each scanned scrambling code on the primary synchronization channel (P-SCH). See also general remarks above.
30 ... 0 dB
The peak code power (Ec) of each scanned scrambling code on the primary synchronization channel (PSCH), relative to the total signal power in the channel (Io). See also general remarks above.
0 ... 51
Pilot scanning: Number of Ec/Io peaks (multipath components) that are above the PN threshold. See also general remarks above.
Sc SC
0 ... 511
Pilot scanning: The number of each scanned scrambling code. See also general remarks above.
247
IE Name Sc SC Group
Range/Unit 0 ... 7
Description Pilot scanning: The number of the group to which each scanned scrambling code belongs. See also general remarks above.
Sc SIR
25 ... 30 dB
Pilot scanning: Received SIR (in dB) for scanned scrambling codes. See also general remarks above.
Sc S-SCH Ec
Pilot scanning: The peak code power of each scanned scrambling code on the secondary synchronization channel (S-SCH). See also general remarks above.
Sc S-SCH Ec/Io
30 ... 0 dB
Pilot scanning: The peak code power (Ec) of each scanned scrambling code on the secondary synchronization channel (S-SCH), relative to the total signal power in the channel (Io). See also general remarks above.
Sc Time Offset
Pilot scanning: The time offset of the radio frame (10 ms = 38,400 chips) for each scanned scrambling code. See also general remarks above.
1 ... 2560
Pilot scanning: Equal to (Sc Time Offset mod 2560) + 1. See also general remarks above.
Sc UARFCN
1 ... 12
Pilot scanning: The UARFCN of the CPICH currently scanned. See also general remarks above.
Sc UL Interference
Pilot scanning: Interference on uplink, extracted from SIB type 7. See also general remarks above.
248
Range/Unit 24 ... 0 dB
Description SCH timeslot scanning: Power in each segment (1, 2, 4, or 8 chips depending on setup) of the scanned timeslot. Argument: Index of timeslot segment (not chip index). If Every 2 has been chosen, the argument range is 1 ... 2560/2, i.e. 1 ... 1280; for Every 4, the range is 1 ... 640; for Every 8, the range is 1 ... 320. SCH timeslot scanning: Number of scanned timeslot segments (each with length 1, 2, 4, or 8 chips depending on setup). SCH timeslot scanning: Position of each timeslot segment scanned, expressed as a chip index. The first chip has number 1. Argument: Index of timeslot segment (not chip index). If Every 2 has been chosen, the argument range is 1 ... 2560/2, i.e. 1 ... 1280; for Every 4, the range is 1 ... 640; for Every 8, the range is 1 ... 320.
SCH TS Sc No of Segm
0 ... 2560
SCH TS Sc Segm
1 ... 2560
SCH timeslot scanning: The time separation in chips between the strongest peak and the second strongest. SCH timeslot scanning: The time separation in chips between the second strongest peak and the third strongest. SCH timeslot scanning: UARFCN scanned.
SCH TS Sc UARFCN
249
Range/Unit
Arg
Description
These elements are populated by spectrum analysis scanning. The argument, where present, is simply a sequence number pointing to scanned frequencies as indicated by the Spectr Ana Sc Freq DL or Spectr Ana Sc Freq UL element.
1930 ... 1990 or 2110 ... 2170 MHz 1930 ... 1990 or 2110 ... 2170 MHz
1 ... 2560
Spectrum analysis: Scanned frequencies on downlink in ascending order. Spectrum analysis: Scanned frequencies on uplink in ascending order. Spectrum analysis: The number of downlink frequencies swept by the scan. Spectrum analysis: The number of uplink frequencies swept by the scan. Spectrum analysis: RSSI of downlink frequencies scanned. Spectrum analysis: RSSI of uplink frequencies scanned.
1 ... 2560
Spectr Ana Sc No of Freq DL Spectr Ana Sc No of Freq UL Spectr Ana Sc RSSI DL Spectr Ana Sc RSSI UL
0 ... 2560
4.3.16.
Serving Cell
Arg
Description Cell identity of the serving cell. Cell Identity part of Serving Cell Id: bits 12 through 27 (in decimal).
250
Arg
Description RNC part of Serving Cell Id: bits 0 through 11 (in decimal).
Name of each cell listed. Requires cell file. RAC of serving cell.
Serving CPICH Ec/No Serving CPICH RSCP Serving Pathloss Serving Primary CPICH TxPower Serving SC
34 ... 0 dB 140 ... 15 dBm 30 ... 165 dB 31 ... 50 dBm 0 ... 511
CPICH Ec/No of the serving cell. CPICH received signal code power of the serving cell. Pathloss of the serving cell. Calculated as Primary CPICH Tx Power CPICH RSCP. CPICH transmit power of the serving cell. Scrambling code of the serving cell in idle, Cell_FACH, Cell_PCH, and URA_PCH mode. Downlink UARFCN of the serving cell in idle, Cell_FACH, Cell_PCH, and URA_PCH mode.
Serving UARFCN DL
251
Arg
4.4.
4.4.1.
IE Name Access Probe Max Req Seq Access Probe Max Rsp Seq Access Probe Num Step Access Probe Number Access Probe Sequence Number EV-DO Access Max Probe Seq EV-DO Access Probe Count EV-DO Access Probe Num Step EV-DO Access Probe Seq Count
0 ... 15
0 ... 255
252
Range/Unit 0 ... 3
Arg
Description Result of EV-DO access attempt: 0: ACAck not received 1: ACAck received 2: TCA message received 3: Probe Interrupted
Time (in slots) taken to complete the EV-DO access attempt. Transaction ID of EV-DO access attempt.
4.4.2.
Active Set
These elements are valid for both 1x and EV-DO. The argument, where present, points to the active set member index.
IE Name Active Set Band Class Active Set Cell Name Range/Unit Text Arg 1 ... 6 Description Frequency band class for each active set member. See 3GPP2 TS C.S0057B. Cell name for each active set member as defined in cell file (if available). Requires that a cell file has been loaded. Active Set Channel Active Set Count Active Set DCCH Code Channel Active Set DCCH QOF Mask Id 0 ... 1199 0 ... 6 0 ... 2047 1 ... 6 1 ... 6 Channel number of RF channel used by each active set member. The number of active set members, whether in idle or traffic mode. DCCH code channel used by each active set member. DCCH QOF mask id used by each active set member.
Text
1 ... 6
0 ... 3
1 ... 6
253
IE Name Active Set Ec Active Set Ec/Io Active Set Ec/Io Sum Active Set FCH Code Channel Active Set FCH QOF Mask Id Active Set PN Active Set SCH Code Channel Active Set SCH QOF Mask Id
Range/Unit 157 ... 10 dBm 32 ... 0 dB 32 ... 0 dB 0 ... 2047 0 ... 3 0 ... 511 0 ... 2047 0 ... 3
Description Received signal code power for each active set member. Signal-to-noise ratio (Ec/Io in dB) for each active set member. Total signal-to-noise ratio (Ec/Io in dB) for all active set members. The summing is done in the mW domain. FCH code channel used by each active set member. FCH QOF mask id used by each active set member. Pilot PN offset for each active set member. SCH code channel used by each active set member. SCH QOF mask id used by each active set member.
4.4.3.
These elements are valid for EV-DO only. The argument, where present, points to the active set member index.
IE Name EV-DO Active Set DRC Cover EV-DO Active Set DRC Lock Range/Unit 0 ... 7 Text Arg 1 ... 6 1 ... 6 Description EV-DO: DRC cover for each active set member. EV-DO: DRC lock status for each active set member: Locked/ Unlocked.
254
Range/Unit 0, 1
Arg 1 ... 6
Description EV-DO: Drop timer for each active set member. 0: Inactive 1: Active
0, 1
1 ... 6
EV-DO: Drop timer status for each active set member. 0: Drop timer running 1: Drop timer expired
EV-DO Active Set MAC Index EV-DO Active Set Predicted DRC EV-DO Active Set Predicted SINR EV-DO Active Set RAB Offset
0 ... 127
1 ... 6
EV-DO: The medium access control index associated with each active set member. EV-DO: DRC cover for the active set pilot currently having the best predicted SINR. EV-DO: Predicted SINR for the active set pilot currently having the best predicted SINR. EV-DO: For each active set member, specifies the slots in which a new reverse activity bit can be transmitted. See 3GPP2 TS C.S0024, section 9.3.1.3.2.2.3. EV-DO: For each active set member, the rate of reverse activity bits during the last PN roll (16 slots), calculated as (number of ones) / 16. EV-DO: Reverse power control index for each active set member. EV-DO: For each active set member, a running average of the last 64 reverse power control bits, showing the recent trend of the power control. See 3GPP2 TS C.S0024, section 9.2.1.2.4.2. EV-DO: DRC cover for the current serving active set pilot.
0 ... 7
1 ... 6
EV-DO Active Set RAB Usage EV-DO Active Set RPC Index EV-DO Active Set RPC Indication
0 ... 100 %
1 ... 6
0 ... 15 1 ... 1
1 ... 6 1 ... 6
0 ... 7
255
IE Name EV-DO Active Set Serving PN EV-DO Active Set Serving RPC EV-DO Active Set Serving SINR EV-DO Active Set SINR EV-DO Active Set Window Center EV-DO Best Pilot PN EV-DO Best SINR
Arg
Description EV-DO: PN offset for the current serving active set pilot. EV-DO: RPC index for the current serving active set pilot. EV-DO: SINR for the current serving active set pilot. EV-DO: Signal to interference-plusnoise ratio for each active set member. EV-DO: Center of search window for each active set member. Given in chip units. EV-DO: PN offset for the active set pilot currently having the best predicted SINR. EV-DO: Predicted SINR for the active set pilot currently having the best predicted SINR.
1 ... 6 1 ... 6
30 ... 15 dB
4.4.4.
Candidate Set
These elements are valid for both 1x and EV-DO. The argument, where present, points to the candidate set member index.
IE Name Candidate Set Band Class Candidate Set Cell Name Candidate Set Channel Range/Unit Text Arg 1 ... 6 Description Frequency band class for each candidate set member. See 3GPP2 TS C.S0057-B. Cell name for each candidate set member as defined in cell file (if available). Channel number of RF channel used by each candidate set member.
Text
1 ... 6
0 ... 1199
1 ... 6
256
IE Name Candidate Set Count Candidate Set Ec Candidate Set Ec/Io Candidate Set PN
Description The number of candidate set members. Received signal code power for each candidate set member. Signal-to-noise ratio (Ec/Io in dB) for each candidate set member. Pilot PN offset for each candidate set member.
4.4.5.
These elements are valid for EV-DO only. The argument, where present, points to the candidate set member index.
IE Name EV-DO Candidate Set Drop Timer Active EV-DO Candidate Set Drop Timer Expired EV-DO Candidate Set Window Center (chips) Range/Unit 0, 1 Arg 1 ... 6 Description EV-DO: Drop timer for each candidate set member. 0: Inactive 1: Active 0, 1 1 ... 6 EV-DO: Status of drop timer for each candidate set member. 0: Drop timer running 1: Drop timer expired 0 ... 23768 chips 1 ... 6 EV-DO: Center of search window for each candidate set member. Given in chip units.
257
4.4.6.
Channel Config
Range/Unit 0 ... 162600 kbit/s Text 0 ... 65535 bits Text Arg Description Forward link DCCH bit rate configuration. State of forward link DCCH: Used/ Not Used. Number of bits in a forward link DCCH physical layer frame. Forward link DCCH frame size in milliseconds. Forward link DCCH MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Forward link DCCH Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. Forward link FCH bit rate configuration. State of forward link FCH: Used/Not Used. Number of bits in a forward link FCH physical layer frame. Forward link FCH frame size in milliseconds. Forward link FCH MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Forward link FCH Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1.
IE Name F-DCCH Bitrate F-DCCH Enabled F-DCCH Frame Length (bits) F-DCCH Frame Size (ms) F-DCCH MUX PDU F-DCCH Radio Configuration F-FCH Bitrate F-FCH Enabled F-FCH Frame Length (bits) F-FCH Frame Size (ms) F-FCH MUX PDU F-FCH Radio Configuration
Text
1 ... 9
0 ... 162600 kbit/s Text 0 ... 65535 bits Text Text 1 ... 9
258
Range/Unit 0 ... 15
Arg
Description Forward link FCH rate bitmask. A combination of: 0x01 (Full Rate allowed), 0x02 (1/2 Rate allowed), 0x04 (1/4 Rate allowed), and 0x08 (1/8 Rate allowed)
0 ... 2 or Text
Forward link FCH traffic type; one of: 0: No forward traffic 1: Primary traffic 2: Secondary traffic
F-SCH Rate
0 ... 5
F-SCH0 Bitrate F-SCH0 Enabled F-SCH0 Frame Length (bits) F-SCH0 MUX PDU F-SCH0 Radio Configuration R-DCCH Bitrate R-DCCH Enabled
F-SCH0 channel bit rate configuration. State of F-SCH0 channel: Used/Not Used. Number of bits in an F-SCH0 physical layer frame. F-SCH0 MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. F-SCH0 Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. Reverse link DCCH bit rate configuration. State of reverse link DCCH: Used/ Not Used.
259
IE Name R-DCCH Frame Length (bits) R-DCCH MUX PDU R-DCCH Radio Configuration R-FCH Bitrate R-FCH Enabled R-FCH Frame Length (bits) R-FCH MUX PDU R-FCH Radio Configuration R-FCH Rate
Arg
Description Number of bits in a reverse link DCCH physical layer frame. Reverse link DCCH MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Reverse link DCCH Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. Reverse link FCH bit rate configuration. State of reverse link FCH: Used/Not Used. Number of bits in a reverse link FCH physical layer frame. Reverse link FCH MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Reverse link FCH Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1. Reverse link FCH rate bitmask. A combination of: 0x01 (Full Rate allowed), 0x02 (1/2 Rate allowed), 0x04 (1/4 Rate allowed), and 0x08 (1/8 Rate allowed)
1 ... 9
0 ... 15
0 ... 2 or Text
Reverse link FCH traffic type; one of: 0: No reverse traffic 1: Primary traffic 2: Secondary traffic
260
Range/Unit 0 ... 5
Arg
R-SCH0 Bitrate R-SCH0 Enabled R-SCH0 Frame Length (bits) R-SCH0 MUX PDU R-SCH0 Radio Configuration
Reverse link SCH0 bit rate configuration. State of reverse link SCH0: Used/ Not Used. Number of bits in a reverse link SCH0 physical layer frame. Reverse link SCH0 MUX PDU type: see 3GPP2 TS C.S0003-A, section 2.2.1.1. Reverse link SCH0 Radio Configuration as specified in 3GPP2 TS C.S0002-A, Table 3.1.3.1-1.
1 ... 9
4.4.7.
Data
Range/Unit 0 ... 4000 kbit/s 0 ... 4000 kbit/s 0 ... 4000 kbit/s Arg Description EV-DO received downlink data rate, instantaneous value. EV-DO received downlink data rate, running average. EV-DO downlink data rate requested by terminal, instantaneous value.
IE Name EV-DO DRC Rate Received EV-DO DRC Rate Received Average EV-DO DRC Rate Requested
261
IE Name EV-DO DRC Rate Requested Average EV-DO FL IEs: General remark EV-DO FL Bad Packet Count
Arg
The argument, where present, points to a DRC index. Arg 0 = DRC index 0x1, etc. 0 ... 231 1 0 ... 13 For each DRC index, the number of packets on the forward link received with bad CRC. Attributes: Current: Number of bad packets accumulated over latest reporting period. Total: Number of bad packets accumulated from start of logfile.
EV-DO FL Bad Packet Rate EV-DO FL Good Packet Count 0 ... 100 % 0 ... 231 1 0 ... 13
For each DRC index, the percentage of bad packets on the forward link. Given for the latest reporting period. For each DRC index, the number of packets on the forward link received with good CRC. Attributes: Current: Number of good packets accumulated over latest reporting period. Total: Number of good packets accumulated from start of logfile.
0 ... 13
EV-DO FL Good Packet Rate EV-DO FL Packet Size EV-DO FL Throughput 0 ... 100 % Text 0 ... 4000 kbit/s 0 ... 13
For each DRC index, the percentage of good packets on the forward link. Given for the latest reporting period. For each DRC index, the raw bit rate on the forward link (kbit/s). Instantaneous EV-DO forward link throughput.
0 ... 13
262
Arg Attributes:
Description
AN Limit: EV-DO reverse link data rate limit imposed by access network (AN). Average: EV-DO reverse link data rate, running average. Current: EV-DO reverse link data rate, instantaneous value. PA Limit: EV-DO reverse link data rate limit imposed by power amplifier (PA).
The argument, where present, points to a reverse link current rate index. 0 ... 231 1 1 ... 5 For each RL current rate, the number of packets sent on the reverse link. Attributes: Current: Number of packets accumulated over the past reporting period. Total: Number of packets accumulated from start of logfile.
EV-DO RL Packet Rate EV-DO RL Packet Size EV-DO RL Throughput 0 ... 100 % Text 0 ... 1800 kbit/s 1 ... 5
Percentage distribution showing the current usage of the reverse link current rates. Based on latest report. For each RL current rate, the raw bit rate on the reverse link. Instantaneous EV-DO reverse link throughput.
1 ... 5
263
Arg Attributes:
Description
Actual: RRI at which the EV-DO reverse link packet was transmitted. Conditional: EV-DO reverse rate indication calculated according to the algorithm in 3GPP2 TS C.S0024, section 8.5.6.1.5.2.
Actual RRI should always be Conditional RRI; if Actual RRI is smaller, then the reverse rate has been demoted, as there is not enough data to be sent. RLP DL Avg. Throughput RLP DL Throughput RLP Erasure Rate RLP Retransmitted Frames Rx RLP Retransmitted Frames Tx 0 ... 4000 kbit/s 0 ... 4000 kbit/s 0 ... 100 % 0 ... 100 % 0 ... 100 % Averaged throughput on downlink at RLP level (16 s sliding window). Instantaneous throughput on downlink at RLP level. Valid for both 1x and EVDO. Erasure rate at RLP level. Retransmitted frames on downlink at RLP level. Retransmitted frames on uplink at RLP level.
264
Arg 0 ... 12
Description RLP downlink physical channel bit rate configuration. Argument: 0: FCH 1: DCCH 2: SCH0 3: SCH1 4: SCCH0 5: SCCH1 6: SCCH2 7: SCCH3 8: SCCH4 9: SCCH5 10: SCCH6 11: SCCH7 12: PDCH
RLP Service ID RLP Total Bytes Rx RLP Total Bytes Tx RLP TX Channel Rate
0 ... 254 0 ... 231 bytes 0 ... 231 bytes 0 ... 162600 kbit/s
0 ... 12
Radio Link Protocol service ID. Total bytes transferred on downlink at RLP level. Total bytes transferred on uplink at RLP level. RLP uplink physical channel bit rate configuration. Argument: See RLP RX Channel Rate.
Averaged throughput on uplink at RLP level (16 s sliding window). Instantaneous throughput on uplink at RLP level. Valid for both 1x and EVDO.
265
4.4.8.
Finger
These elements are valid for both 1x and EV-DO. The argument, where present, points to the finger index.
IE Name Finger Count Finger Delay (chips) Range/Unit 0 ... 12 0 ... 32768 chips Arg 1 ... 12 Description Number of valid fingers. Attributes: Abs: The absolute position of each finger in chips. Delta: The position of each finger (in chips) relative to the earliest finger arrived.
Finger Energy
1 ... 12
Signal-to-noise ratio for each finger: Ec/Io for 1x fingers, SINR for EV-DO fingers. Total signal-to-noise ratio for all fingers, instantaneous value: Ec/Io for 1x fingers, SINR for EV-DO fingers. Pilot PN for each finger. Status of each finger: a combination of Reference, Locked, and Assigned. Searcher state, e.g. Acquisition, TCH operation.
1 ... 12 1 ... 12
Searcher State
Text
266
4.4.9.
Finger EV-DO
These elements are valid for EV-DO only. The argument, where present, points to the finger index.
IE Name EV-DO Finger Antenna Selection Range/Unit 0, 1 Arg 1 ... 12 Description Antenna(s) selected for each EV-DO finger. Of interest only if the access terminal is equipped with two antennas and is enabled to use both. 0: Antenna 0 1: Antenna 1 EV-DO Finger C/I 30 ... 15 dB 1 ... 12 EV-DO: When antenna diversity is enabled, for each finger, the cumulative energy of all search results for one antenna. Attributes: EV-DO Finger Diversity Enabled 0, 1 1 ... 12 Antenna 0 Antenna 1
State of EV-DO antenna diversity. Relevant only if the access terminal is equipped with two antennas. 0: Not enabled 1: Enabled
1 ... 12
The index of the EV-DO finger. EV-DO Mobile Station Time Reference: the access terminals current timing reference based on the sync channel time (in slots) and on the finger lock to the earliest arriving usable multipath of a pilot. Given in units of 1/8 chip. Finger delay for each EV-DO finger, expressed as an offset from the current MSTR. Given in units of 1/8 chip.
1 ... 12
267
IE Name EV-DO Finger MSTR Pilot PN EV-DO Finger RPC Cell Index
Arg 1 ... 12
Description EV-DO: PN offset of pilot currently used as timing reference. EV-DO RPC Cell Index. Pilots that have the same RPC bit for the AT share the same value.
4.4.10.
Mobile
Range/Unit Text Arg Description The number dialed to initiate the current call. Valid only while a call is in progress. Mobile Identification Number. Qualcomm chipset family (e.g. MSM6800). Phone protocol revision (P-Rev).
MIN MSM Revision Protocol Revision Mobile Slot Cycle Index Station Class Mark
Slot cycle index described in 3GPP2 TS C.S0005-A, section 2.6.2.1.1.3. Defined in 3GPP2 TS C.S0005-A, section 2.3.3.
4.4.11.
Neighbor Set
These elements are valid for both 1x and EV-DO. The argument, where present, points to the neighbor set member index.
268
Range/Unit Text
Arg 1 ... 40
Description Frequency band class for each neighbor set member. See 3GPP2 TS C.S0057-B. Argument: Neighbor set member index.
Text
1 ... 40
Cell name for each neighbor set member as defined in cell file (if available). Requires that a cell file has been loaded. Argument: Neighbor set member index.
0 ... 1199
1 ... 40
Channel number of RF channel used by each neighbor set member. Argument: Neighbor set member index.
1 ... 40
The number of neighbor set members. Received signal code power for each neighbor set member. Argument: Neighbor set member index.
32 ... 0 dB
1 ... 40
Signal-to-noise ratio (Ec/Io in dB) for each neighbor set member. Argument: Neighbor set member index.
Neighbor Set PN
0 ... 511
1 ... 40
Pilot PN offset for each neighbor set member. Argument: Neighbor set member index.
269
4.4.12.
These elements are valid for EV-DO only. The argument, where present, points to the neighbor set member index.
IE Name EV-DO Neighbor Set Age EV-DO Neighbor Set Window Offset EV-DO Neighbor Set Window Size Range/Unit 0 ... 65535 Arg 1 ... 40 Description EV-DO: Age counter for each neighbor set member. See 3GPP2 TS C.S0024, section 6.6.6.1.2.7. EV-DO: Offset (from MSTR) of search window used for each neighbor set member. EV-DO: Size of search window used for each neighbor set member.
1 ... 40
1 ... 40
4.4.13.
Pilot Set
The argument, where present, points to the pilot set member index.
IE Name Pilot PN Increment Pilot Set Band Class Pilot Set Cell Name Range/Unit 1 ... 15 Arg Description Inter-sector pilot PN increment used by the AN in assigning PN offsets to sectors. Frequency band class for each pilot set member. See 3GPP2 TS C.S0057B. Cell name for each pilot set member as defined in cell file (if available). Requires that a cell file has been loaded. Pilot Set Cell Type Pilot Set Channel Text 0 ... 1199 1 ... 52 1 ... 52 Type of pilot: Active, Candidate, or Neighbor. Channel number of RF channel used by each pilot.
Text
1 ... 52
Text
1 ... 52
270
Description Total number of pilots in active, candidate, and neighbor sets. Signal-to-noise ratio for each pilot set member. PN offset for each pilot set member.
4.4.14.
Polluters
These elements are obtained when using a scanner in follow phone mode: see DC UM, section 12.3. Current refers to the polluter data derived from the latest scan report. Top List refers to cumulative polluter statistics amassed since start of logfile/since device connect.
IE Name Polluters Current Active Set Polluters Current Cell Name Range/Unit 0 ... 511 Arg 1 ... 6 Description PN offset of each current active set member. Argument: Active set member index. Text 1 ... 5 Cell name of each current polluter, as defined in cell file (if available). Argument: Rank of this polluter among current polluters. 32 ... 0 dB 1 ... 5 Signal-to-noise ratio for each current polluter. Argument: Rank of this polluter among current polluters. Polluters Current Pilot PN Polluters Top List Cell Name 0 ... 511 1 ... 5 PN offset of each current polluter. Argument: Rank of this polluter among current polluters. Text 1 ... 5 Cell name of each polluter on the top list. Argument: Rank on polluter top list.
271
Arg 1 ... 5
Description RF channel number of each polluter on the top list. Argument: Rank on polluter top list.
0 ... 511
1 ... 5
PN offset of each polluter on the top list. Argument: Rank on polluter top list.
4.4.15.
Power
272
4.4.16.
Power EV-DO
4.4.17.
Quality Measurement
See the descriptions (cellular technology independent) under GSM, section 4.2.6. IE Name Frequent AQM elements PESQ elements Speech Path Delay SQI MOS
273
4.4.18.
Radio Measurement
Range/Unit 0 ... 5 or Text Arg Description EV-DO access terminal state. 0: Inactive (AT switched to 1X or is in Deep Sleep) 1: Acquisition 2: Sync 3: Idle 4: Access 5: Connected EV-DO base station color code. Tells whether the access terminal is in hybrid mode: On or Off. A terminal in hybrid mode is monitoring both 1x and EV-DO paging channels in idle mode. EV-DO Packet Error Rate. Attributes: Instantaneous: Immediate value (no averaging). Short: Running average over (approximately) 60 reports. Long: Running average over (approximately) 600 reports.
EV-DO PER
0 ... 100 %
0 ... 5 or Text
EV-DO session state. One of: 0: Closed 1: AMP setup 2: AT-initiated negotiation 3: AN-initiated negotiation 4: Open 5: Closing
274
Arg 1 ... 8
Description EV-DO: List of active UATIs (Unicast Access Terminal Identifiers), given as 32-bit values (lowest 4 bytes of full UATI). Argument: Sequence number.
EV-DO UATI Count FER DCCH FER FCH FER SCH0 FER SCH1 FER Total Frame Offset
0 ... 8 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 100 % 0 ... 15 See Description
EV-DO: Number of active UATIs. Frame erasure rate on the DCCH (Digital Control Channel). Frame erasure rate on the FCH (Fundamental Channel). Frame erasure rate on the SCH0 (Supplemental Channel 0). Frame erasure rate on the SCH1 (Supplemental Channel 1). Frame erasure rate calculated over all forward channels. A time skewing of Traffic Channel frames from System Time in integer multiples of 1.25 ms. The maximum frame offset is 15 1.25 ms = 18.75 ms. Service Option for the current session. See 3GPP2 TS C.R1001. Soft handoff state. One of No Soft Handoff, 2-Way, 3-Way, 4-Way, 5-Way, 6-Way. Derived from the information element Active Set Count.
275
4.4.19.
Scan Data
276
IE Name Scanned Ec Scanned Ec/Io Scanned Io Scanned Pilot PN Scanned Pilots Count
Range/Unit 157 ... 10 dBm 32 ... 0 dB 125 ... 25 dBm 0 ... 511 0 ... 512
Arg 1 ... 4; 1 ... 512 1 ... 4; 1 ... 512 1 ... 4 1 ... 4; 1 ... 512 1 ... 4
Description Received signal code power of each scanned pilot. Peak Ec/Io for each scanned pilot. Total signal power in RF channel. PN offset for each scanned pilot. Number of pilots scanned.
120 ... 30
1 ... 512
RSSI for each RF channel. Argument: 1 means the RF channel with the lowest number, etc.
4.4.20.
Server
Range/Unit 0 ... 65535 Arg Description Base ID transmitted in Layer 3 message System Parameters.
IE Name Base ID
277
Range/Unit Text
Description
Entering CDMA Sync Channel Paging Channel Traffic Channel Initialization Traffic Channel Exit
Country ID EV-DO Revision Network ID Protocol Revision Base Protocol Revision In Use RF Mode
0 ... 999 Text 0 ... 65535 0 ... 7 or Text 0 ... 7 or Text Text
MCC, Mobile Country Code. EV-DO revision: Rev 0 or Rev A. Network Identification (NID). Base station protocol revision (P-Rev).
Protocol revision (P-Rev) negotiated between phone and base station. Text string <technology> <phone state>, where <technology> is one of Analog, CDMA, 1xEV-DO, and <phone state> is one of Init, Idle, Access, Traffic
Searcher Window A
Size of search window used for pilots in the active set. For the mapping to PN chip length see IS-95, Table 6.6.6.2.1-1. Size of search window used for pilots in the neighbor set. Size of search window used for pilots in the remaining set (see 3GPP2 TS C.S0005-A, page 1-18).
278
IE Name Sector ID
Range/Unit Text
Arg
Description Hex string containing the 128-bit sector address of the serving sector. Format: 0011:2233:4455:6677:8899:AABB:CC DD:EEFF Sector subnet identifier. System Identification (SID). Pilot detection threshold (sign reversed). See 3GPP2 TS C.S0005-A, section 2.6.6.2.6.2. Pilot detection threshold (expressed in units of 0.5 dB and sign reversed). See 3GPP2 TS C.S0005-A, section 1.1.2.2.
T-Comp
Active set versus candidate set comparison threshold. See 3GPP2 TS C.S0005-A, section 2.6.6.2.5.2. Active set versus candidate set comparison threshold (expressed in units of 0.5 dB).
T-Drop
Pilot drop threshold (sign reversed). See 3GPP2 TS C.S0005-A, section 2.6.6.2.3. Pilot drop threshold (expressed in units of 0.5 dB and sign reversed).
279
IE Name T-TDrop
Arg
Description Drop timer value, mapped to an integer value according to 3GPP2 TS C.S0005-A v6.0, Table 2.6.6.2.3-1.
Drop timer value in seconds. See 3GPP2 TS C.S0005-A v6.0, Table 2.6.6.2.3-1.
4.4.21.
Session EV-DO
0 ... 255 0, 1
0 ... 255
280
4.4.22.
Statistics
Range/Unit 0 ... 1000 0 ... 1000 0 ... 1000 0 ... 100 % Arg Description Number of Blocked Call events. Regarding this event, see section 7.3. Number of Dropped Call events. Regarding this event, see section 7.3. Number of Call End events. Regarding this event, see section 7.3. Calculated as: # blocks / (# blocks + # drops + # ends) where blocks = Blocked Call events drops = Dropped Call events ends = Call End events Regarding the events, see section 7.3.
IE Name Call Blocked Count Call Dropped Count Call Success Count Calls Blocked
Calls Dropped
0 ... 100 %
Calculated as: # drops / (# blocks + # drops + # ends) where blocks = Blocked Call events drops = Dropped Call events ends = Call End events Regarding the events, see section 7.3.
EV-DO Access Failure Rate EV-DO Connection Failure Rate EV-DO Session Failure Rate
Number of failed EV-DO access attempts divided by total number of EV-DO access attempts. Number of failed EV-DO connection attempts divided by total number of EV-DO connection attempts. Number of failed EV-DO session attempts divided by total number of EV-DO session attempts.
281
4.5.
0 ... 2 109 bytes 0 ... 80000 kbit/s 0 ... 80000 kbit/s Text hh:mm:ss
Data Connection Type IP Address NDIS/RAS IEs: General remark NDIS/RAS Bytes Received NDIS/RAS Bytes Sent NDIS/RAS Current Throughput DL
Text
Text
These elements are valid for a RAS connection as well as an NDIS connection. 0 ... 2 109 bytes 0 ... 2 109 bytes 0 ... 80000 kbit/s Number of bytes received over the current data connection. Number of bytes sent over the current data connection. Downlink throughput on the current data connection.
282
Arg
Description Uplink throughput on the current data connection. Round-trip time for an individual Ping Response during the current Ping session. Valid only during Ping sessions.
Ping Size
Size in bytes of the packet sent with the Ping command. Valid only during Ping sessions.
RAS IEs: General remark RAS Alignment Errors RAS Buffer Overrun Errors RAS Compression Ratio In RAS Compression Ratio Out RAS CRC Errors RAS Frames Received RAS Frames Sent RAS Framing Errors
These elements are valid only if the device uses a RAS dial-up connection. 0 ... 2 109 0 ... 2 109 0 ... 2000 Number of alignment errors on the current dial-up connection. Number of buffer overrun errors on the current dial-up connection. Compression ratio for the data being received on the current dial-up connection. Compression ratio for the data being sent on the current dial-up connection. Number of cyclic redundancy check (CRC) errors on the current dial-up connection. Number of frames received over the current dial-up connection. Number of frames sent over the current dial-up connection. Number of framing errors on the current dial-up connection.
0 ... 2000
0 ... 2 109
283
IE Name RAS Hardware Overrun Errors RAS Timeout Errors Session App. Bytes Received Session App. Bytes Sent Session App. Mean Throughput DL Session App. Mean Throughput UL Session Current Packet Loss Session Current Throughput DL
Range/Unit 0 ... 2 109 0 ... 2 109 0 ... 2 109 bytes 0 ... 2 109 bytes 0 ... 80000 kbit/s
Arg
Description Number of hardware overrun errors on the current dial-up connection. Number of timeout errors on the current dial-up connection. Number of bytes received at the application level during the current session. Number of bytes sent at the application level during the current session. Mean throughput, calculated over the whole of the current session, for data received at the application level (mean downlink throughput). Mean throughput, calculated over the whole of the current session, for data sent at the application level (mean uplink throughput). Current packet loss level in percent. (Useful when testing video streaming.) Same as App. Throughput DL except that this element is valid only while a data transfer session is in progress. This element is more suitable to use for statistics, since it will not contain any zeroes from periods of inactivity. Same as App. Throughput UL except that this element is valid only while a data transfer session is in progress. This element is more suitable to use for statistics, since it will not contain any zeroes from periods of inactivity. Time for which the current session has been ongoing. Given in hours, minutes, and seconds.
Session Duration
Text hh:mm:ss
284
Range/Unit Text
Arg
Description Description of the current session in plain text, e.g. FTP DL: www.my_server.com/temp/my_file.txt. Average of the latest 30 VSQI Realtime Scores (which see). Video Streaming Quality Index (realtime score which is regularly updated during the streaming session, unlike the overall VSQI score for an entire session which appears in the Session End report). See DC UM chapter 31.
285
5.
These tables are valid for Data Collection and Route Analysis alike. Elements derived from positioning equipment are not included in the tables. In the Information Elements column, <string>* means all IEs beginning with <string>. A gray checkmark means that the IE support is restricted to a subset of the devices in the column; see the accompanying footnote for details. The tables include certain devices that are no longer connectable in this version of TEMS Investigation; these devices are printed in non-boldface. They are retained here since old logfiles recorded with the devices can still be replayed in the application. There also exist information elements which are unique to one or more of these devices.
5.1.
EV-DO Color Code EV-DO* (others) Missing Neighbor* Polluters* Sector ID Subnet Mask
286
PCTel Scanners
Qualcomm
5.2.
The Sony Ericsson column containing Z750i is also valid for TM506.
Sony Ericsson Motorola Nokia Qualc.
Information Elements
Adjacent RxLev* Adjacent Scan AMR Active Set* AMR C/I* AMR Codec* AMR Hysteresis AMR Threshold ARFCN* Attach Time Band Control BER* BLER/Timeslot
Z750i, C702, C905/a, W760i K600i, K800i W600i, K790i/a V800, Z800 S710a T610, T616, T618 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845 6120/1, 7376, N75/80/95/96 6086, 6125, 6230(i), 6280 6630, 6680 6650, 6651 HSPA, HSPA+ HSDPA WCDMA Datang LC8130E PCTel Scanners 287
PCTel Scanners
Sony Ericsson
Motorola
Nokia
Qualc.
Information Elements
BSIC* a C Value C/A* b C/I Absolute, Best, Best: ARFCN, Worst, Worst: ARFCN c C/I* (others) C1 C2 C31 C32 Cell EGPRS Support Cell GPRS Support Cell Id* Cell Name* CGI* Channel* Ciphering Algorithm Coding Scheme DL Coding Scheme UL CS-* DL Usage... Current CS* Current MCS* Data Mode* Disable Handover d Downlink Sign. Ctr Curr. Downlink Sign. Ctr Max DTX Rate DL EGPRS BEP (*) EGPRS BEP Total (*)
288
Z750i, C702, C905/a, W760i K600i, K800i W600i, K790i/a V800, Z800 S710a T610, T616, T618 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845 6120/1, 7376, N75/80/95/96 6086, 6125, 6230(i), 6280 6630, 6680 6650, 6651 HSPA, HSPA+ HSDPA WCDMA Datang LC8130E PCTel Scanners
Sony Ericsson
Motorola
Nokia
Qualc.
Information Elements
EGPRS Link Q. Ctrl UL EGPRS Window Size* FER* Firmware Version Forced* Frequency Band* Frequent AQM* e GA-RC*, GAN*, GANC* f GMM State GRR State Hardware Hardware ID Hopping* HSN Idle Channel Quality Ignore Cell Barred Interference* LAC* LLC BLER DL LLC BLER UL LLC Bytes* LLC Throughput* LLC Window Size* MAC Mode* MAIO MCC MCS-* DL Usage... Message Hex Dump... MNC Mode*
Z750i, C702, C905/a, W760i K600i, K800i W600i, K790i/a V800, Z800 S710a T610, T616, T618 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845 6120/1, 7376, N75/80/95/96 6086, 6125, 6230(i), 6280 6630, 6680 6650, 6651 HSPA, HSPA+ HSDPA WCDMA Datang LC8130E PCTel Scanners 289
Sony Ericsson
Motorola
Nokia
Qualc.
Information Elements
Modulation* g MS Behavior Modified MS Power Control Level MS Tx Power Neighbor ARFCN* Neighbor BSIC* Neighbor C1* Neighbor C2* Neighbor C31* Neighbor C32* Neighbor Cell* Neighbor LAC* Neighbor RxLev* Neighbor (SI) ARFCN Network Control Order Network Mode Of Oper. Number Of Hopp. Freq. Number Of Used Tslots* PBCCH Timeslot PDCH Utilization* PDP* PESQ* e Preferred GAN Mode f Prevent* Q Search Power h RAC* Radio Link Timeout Curr. Radio Link Timeout Max RLA_P* RLC BLER*
290
Z750i, C702, C905/a, W760i K600i, K800i W600i, K790i/a V800, Z800 S710a T610, T616, T618 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845 6120/1, 7376, N75/80/95/96 6086, 6125, 6230(i), 6280 6630, 6680 6650, 6651 HSPA, HSPA+ HSDPA WCDMA Datang LC8130E PCTel Scanners
Sony Ericsson
Motorola
Nokia
Qualc.
Information Elements
RLC Block* RLC Bytes* RLC Thrput DL (%) RLC Thrput DL (kbit/s) RLC Thrput UL (%) i RLC Thrput UL (kbit/s) RLP* RxLev* RxQual* Scanned Adjacent* Scanned ARFCN Scanned Band Scanned BSIC Scanned C/A* Scanned C/I Scanned Cell Name Scanned Channels No of Scanned RxLev* Serving Cell List Active Signal Strength* SNDCP BLER* SNDCP Bytes* SNDCP Throughput DL SNDCP Throughput UL Speech Codec Speech Path Delay e SQI* Strongest Sc. C/I Strongest Sc.* (others) Sub Channel Number
Z750i, C702, C905/a, W760i K600i, K800i W600i, K790i/a V800, Z800 S710a T610, T616, T618 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845 6120/1, 7376, N75/80/95/96 6086, 6125, 6230(i), 6280 6630, 6680 6650, 6651 HSPA, HSPA+ HSDPA WCDMA Datang LC8130E PCTel Scanners 291
Sony Ericsson
Motorola
Nokia
Qualc.
Information Elements
TA Target Handover TD-SCDMA Neighbor* TFI* Time Timeslot Timeslot Channel Type* Timeslot Used* TLLI* Training Sequence Code Uplink State Flag WCDMA Neighbor* Weakest Sc. C/I Weakest Sc.* (others) a. Regarding BSIC decoding with PCTel scanners, see DC UM section 9.2.3. b. Option must be turned on in phones Properties dialog: see DC UM section 15.2.3.4. c. For PCTel scanners this requires the C/I measurement option: see DC UM section 9.2.3. d. Supported by C905/C905a, C702, and W760i. e. Supported by Z750i, K800i, and K790i/K790a. Also note that what AQM elements are obtained depends on what hardware is used at the other end: Call Generator with analog calling card, Call Generator with digital calling card, or an MRU. For full details, consult the document AQM in TEMS Products (Including PESQ). f. Supported by Nokia 6086 only. g. Supported by K800i but not by K600i. h. Supported by K790i/K790a but not by W600i. i. Supported by K790i/K790a and K800i but not by W600i and K600i.
292
Z750i, C702, C905/a, W760i K600i, K800i W600i, K790i/a V800, Z800 S710a T610, T616, T618 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845 6120/1, 7376, N75/80/95/96 6086, 6125, 6230(i), 6280 6630, 6680 6650, 6651 HSPA, HSPA+ HSDPA WCDMA Datang LC8130E PCTel Scanners
5.3.
The Sony Ericsson column containing Z750i is also valid for TM506.
SE Motorola Nokia Qualc. Scan.
Z750i C702 C905/a W760i K800i K600i V800, Z800 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845
Information Elements
AMR* a AS* Averaged BER BLER Target Control* Call Event Success Rate Cell Barred Control* Compressed Mode CW* Det Neigh CPICH Tx P. Det Neigh Pathloss Det Neigh* (others) DPCCH* DTX Rate DL DVB-H* Finger 1st* Finger 2nd*, 3rd*, 4th* Finger 5th* ... 12th* Firmware Version Frequent AQM* c GSM Neigh* Hardware HO Event Type* HS 64-QAM Mod. Rate HS MIMO* HS Phy* HS UL* HS* (others)
HSPA+ HSPA HSDPA WCDMA Anritsu PCTel SeeGull LX, EX Rohde & Schwarz 293
SE
Motorola
Nokia
Qualc.
Scan.
Z750i C702 C905/a W760i K800i K600i V800, Z800 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845
Information Elements
HS-DSCH HARQ Pr... HS-DSCH Post Rate HS-DSCH Pre Rate HS-DSCH Throughput HS-DSCH * Per Process HS-DSCH* (others) HS-SCCH* IMEI Inter-freq* Inter-RAT* Intra-freq* MCC Message Hex Dump... MNC Mode* Mon Neigh CPICH Tx P. Mon Neigh Pathloss Mon Neigh* (others) MS Behavior Modified Network Search* Other/Own 1st*, 2nd* Other/Own 3rd*, 4th* Other/Own 5th* ... 12th* PDP* PESQ* c Poss No ... AS M. 12 Poss No ... AS M. 34 Poss No ... AS M. 512 Power Control Ind. RACH Initial TX
294
HSPA+ HSPA HSDPA WCDMA Anritsu PCTel SeeGull LX, EX Rohde & Schwarz
EX EX
SE
Motorola
Nokia
Qualc.
Scan.
Z750i C702 C905/a W760i K800i K600i V800, Z800 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845
Information Elements
RACH Max Preambles RACH Message TX RACH Transm. Preamb. RAT Control* RB Setup UL DPCH SC RLC AM* RLC DL Ent. Data Mode RLC DL Throughput RLC No Of Entities RLC UL Ent. Data Mode RLC UL Throughput RLC/Trsp DL Thrput RLC/Trsp UL Thrput RRC State* SAN Cell Id* SAN CPICH Tx Power SAN Pathloss SAN URA Id SAN* (others) Sc [1st4th] Aggr Eb/Io Sc [1st4th] Aggr Ec Sc [1st4th] Aggr Ec/Io Sc [1st4th] AgPk Ec Sc [1st4th] Cell* Sc [1st4th] Delay Spr. Sc [1st4th] Intra-fr. C. Sc [1st4th] Io Sc [1st4th] No Of SCs Sc [1st4th] Peak* Sc [1st4th] P-SCH*
HSPA+ HSPA HSDPA WCDMA Anritsu PCTel SeeGull LX, EX Rohde & Schwarz
EX
295
SE
Motorola
Nokia
Qualc.
Scan.
Z750i C702 C905/a W760i K800i K600i V800, Z800 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845
Information Elements
Sc [1st4th] Rake F. C. Sc [1st4th] SC Sc [1st4th] SC Group Sc [1st4th] SIR Sc [1st4th] S-SCH* Sc [1st4th] Time Offset* Sc [1st4th] UARFCN Sc [1st4th] UL Interf. Sc [5th12th]* Sc Best*: same as Sc [1st4th]*, see above SCH TS Sc* Sector Control Serving Cell Id* Serving Cell LAC* Serving Cell RAC* Serving URA Id Serving* (others) SF* SHO* SIR SIR Target Spectr Ana DL* Spectr Ana UL* SQI* Str Neigh* Time Trsp Ch BLER* Trsp Ch Id DL Trsp Ch No Of DL Trsp Ch No Of Error Bl.
296
HSPA+ HSPA HSDPA WCDMA Anritsu PCTel SeeGull LX, EX Rohde & Schwarz
EX LX
SE
Motorola
Nokia
Qualc.
Scan.
Z750i C702 C905/a W760i K800i K600i V800, Z800 Razr V3xx, Razr2 V9 E1000, E1070, Razr V3x A835, A845
Information Elements
Trsp Ch No Of UL Trsp Ch Throughput* Trsp Ch Type* UE Initial Transmit Pwr UE Tx Power UL Interference Serving UTRA Carrier RSSI VTQI d e a. Supported by N96 only. b. TCC protocol terminals are no longer connectable in TEMS Investigation. Nevertheless, information elements supported only by TCC protocol terminals remain in the application and are kept in this table, since old logfiles recorded with these terminals can still be replayed. c. Gray checkmark: Supported only by Z750i among these phones. Also note that what AQM elements are obtained depends on what hardware is used at the other end: Call Generator with analog calling card, Call Generator with digital calling card, or an MRU. For full details, consult the document AQM in TEMS Products (Including PESQ). d. Not supported by Sony Ericsson W760i. e. Note on Nokia phones: VTQI is based on transport channel BLER. Nokia phones do not report BLER for individual transport channels but only an average over all channels (see Trsp Ch BLER, DL (Log). This means that VTQI scores based on Nokia reports will not be accurate if further transport channels are used in parallel with the one used for the video call.
5.4.
All LTE elements are populated by both DRT and PCTel, except: Sc <nth> BCH RSSI (dBm): Obtained from DRT only. Sc <nth> CFO (Hz): Obtained from DRT only.
HSPA+ HSPA HSDPA WCDMA Anritsu PCTel SeeGull LX, EX Rohde & Schwarz 297
6.
6.1.
While in soft handover, the phone is power controlled jointly by all members of the active set. Power control commands are received on the DPCCH. Certain Sony Ericsson phones deliver two mode reports that are relevant in this context, TPC Info and DPCCH DL. TPC Info shows the power control commands from each cell in the active set separately, whereas the DPCCH DL report gives the final power control decision obtained by combining and weighting the input from all active set members. The plain-text decoding of the TPC Info mode report represents the power control commands from each cell by a string of letters as follows: Q = Not valid: The cell was not part of the active set at this time. U = Up: The cell ordered the phone to raise the power. D = Down: The cell ordered the phone to lower the power. C = Skip: The phone was in compressed mode at this time, measuring on a different UARFCN or on GSM. N = No change: No power control command, power unchanged.
Since the power control frequency is 1500 Hz, each letter in the string represents 1/1500 of a second.
298
7.
Predefined Events
Here all predefined events are listed and explained, along with any extra information provided in the application (see section 8.3.3). All cause values are decoded into plain-text format in the presentation. Not all of the extra information listed in the table is necessarily included every time the event occurs. The descriptions of how events are triggered are not always exhaustive. In exceptional cases, an event may be triggered by a message not mentioned here. Event symbols shown are default symbols in Data Collection; they can be changed in line charts (DC UM section 23.4.3) and maps (DC UM section 25.5.4). In Route Analysis the symbols used for events are fixed.
7.1.
General Events
Under this heading have been collected events that do not result from interaction with a cellular network.
Event Name Filemark GPS Connected Symbol Description/Extra Information A filemark was encountered in the logfile. A GPS unit has been connected in TEMS Investigation. Generated in drive testing mode only; thus never displayed in Route Analysis. Can only be associated with an audio indication; cannot appear in presentation windows. A GPS unit has been disconnected in TEMS Investigation. Generated in drive testing mode only; thus never displayed in Route Analysis. Can only be associated with an audio indication; cannot appear in presentation windows.
GPS Disconnected
299
Symbol
Description/Extra Information Positions reported by the GPS unit have become invalid (GPS coverage lost).
(red triangle) GPS Position Valid (dark green circle) MS Connected (green) MS Disconnected (red) Recording Paused Recording Resumed Scanner Connected (green) Scanner Disconnected GPS positions are valid again (GPS coverage regained). Reported after an GPS Position Invalid event has occurred.
A phone has been connected in TEMS Investigation. A phone has been disconnected in TEMS Investigation. The recording of a logfile has been paused. The recording of a logfile has been resumed. A scanner has been connected in TEMS Investigation. A scanner has been disconnected in TEMS Investigation.
(red)
300
7.2.
GSM/WCDMA/TD-SCDMA Events
Events in this category are generated by phones supporting at least one of the technologies GSM, WCDMA, and TD-SCDMA. The following is to be noted: For GAN-capable phones, call events in GAN mode are triggered in precisely the same manner as in GSM mode. This is achieved by unpacking Direct Transfer messages and extracting embedded GSM Layer 3 messages. For TD-SCDMA phones a subset of the listed events can be generated (in both TD-SCDMA and GSM mode). The extra information given in the table is rarely provided with events originating from TD-SCDMA phones.
The asterisk column uses the following codes: Code c e g g w ga sg sw w Meaning Requires that a cell file has been loaded. Generated in EDGE mode. Generated in GSM mode. Generated in GSM and WCDMA mode. Generated by GAN-capable phone interacting with a GANC. Generated during GSM scanning. Generated during WCDMA scanning. Generated in WCDMA mode.
Event List
Event Name AQM Out of Synch Symbol * g w Description/Extra Information The synchronization between the AQM module and the Call Generator has been lost. See the document AQM in TEMS Products (Including PESQ).
301
Symbol
* g w
Description/Extra Information The synchronization between the AQM module and the Call Generator has been re-established. See the document AQM in TEMS Products (Including PESQ). The authentication or ciphering failed. Can be generated for both packetswitched and circuit-switched. Extra information: GMM/MM cause (if available).
Authentication Failure
g w
g w ga
GSM/WCDMA/TD-SCDMA: Call abnormally ended prior to Call Established event (for example because all traffic channels were busy). GAN: Layer 3 message Activate Channel Failure received prior to Call Established. Extra information: Block type CC cause RR cause Call time (time since Call Initiation event)
302
Symbol
* g w ga
Description/Extra Information GSM: A traffic channel has been requested (through the Layer 3 message Channel Request). (Note that the request could also be for a signaling channel, in which case no call is actually attempted; the two types of request cannot be distinguished.) WCDMA/TD-SCDMA: An RRC Connection Request has been sent following initiation of an MO or MT call. GAN: (MO call) GAN Layer 3 message Request sent with establishment cause 64 (TCH/H sufficient) or 224 (TCH/F needed). (MT call) GAN Layer 3 message Paging Request received.
(gray)
A call attempt (see the event Call Attempt) was repeated. Triggered by Channel Request/RRC Connection Request. A call has been terminated. This event is normally triggered by the CC message Release. Extra information: Call end cause (usually one of MS initiated release, NW initiated release, User busy) Call duration
A call has been established. The event is triggered by (GSM/WCDMA/TD-SCDMA:) the Layer 3 message Connect (MO call) or Connect Acknowledge (MT call) (GAN:) the Layer 3 message Activate Channel Complete.
303
Symbol
* g w
Description/Extra Information An MO call has been initiated by a command sequence (the equivalent of the yes button being pressed on the handset). This event is normally triggered by a report from the PC communication protocol, never by a Layer 3 message. This event precedes Call Attempt.
Call Setup
g w ga
A call has been set up by the phone. The event is triggered by (GSM/WCDMA/TD-SCDMA:) one of the Layer 3 messages Alerting or Connect (GAN:) the GAN Layer 3 message Activate Channel. Call direction (MO/MT) Call setup time (measured from Call Attempt, i.e. the first call attempt) User setup time (measured from Call Initiation, thus more accurately reflecting the user-perceived setup time; obtained only for MO calls in command sequence)
Extra information:
Successful cell change order: handover from UTRAN to GSM packet data channel. Generated after entering GSM mode. Only occurs when the change takes place from Cell_DCH mode. If it takes place from a Common channel, the event Cell Reselection From UTRAN is generated instead.
304
Symbol
* w
Description/Extra Information Successful cell change order: handover from GSM to UTRAN packet data channel. Generated after entering WCDMA mode. Only occurs when the change is to Cell_DCH mode. If it is to a Common channel, the event Cell Reselection To UTRAN is generated instead.
g g w
Cell change order to UTRAN failed. Cell reselection within GSM or within UTRAN (intra-frequency). Extra information (GSM): BCCH ARFCN and BSIC of new cell.
Cell Reselection From UTRAN Cell Reselection To UTRAN Compressed Mode Entered Compressed Mode Exited Datalink Failure
g w w w g
Cell reselection from UTRAN to GSM. Generated after entering GSM mode. Cell reselection from GSM to UTRAN. Generated after entering WCDMA mode. The phone has entered compressed mode. The phone has left compressed mode. Datalink failure caused by unsolicited Disconnected Mode response or sequence error. The phone has entered dedicated mode. Extra information: BCCH ARFCN and BSIC.
Dedicated Mode
305
Symbol
* g w
Description/Extra Information Call abnormally ended after Call Established event. Extra information: Drop type Cause CC cause Call duration (time since Call Established event)
The phones status buffer has filled up so that the phone is no longer able to use Incremental Redundancy on the downlink for link quality control. Consequently it is forced to switch to using Link Adaptation. Successful intercell handover in GSM. An attempted intercell handover in GSM failed. Successful handover from GAN to GERAN (GSM). Triggered by GAN Layer 3 message Handover Command if followed by Deregister or if a period of 2 s passes without Handover Failure being received.
g g ga
ga
Handover from GAN to GERAN (GSM) failed. Triggered by GAN Layer 3 message Handover Failure.
Handover from UTRAN to GSM accomplished. Generated after entering GSM mode. Handover from UTRAN to GSM failed. Successful intracell handover in GSM.
w g
306
Symbol
* g ga
Description/Extra Information An attempted intracell handover in GSM failed. Successful handover from GERAN (GSM) to GAN. Triggered by GAN Layer 3 message Handover Complete.
ga
Handover from GERAN (GSM) to GAN failed. Triggered if TU3920 timer expires after Handover Access without Handover Complete being received. TU3920 is a timer included in the Register Accept message sent from the GANC.
Handover To UTRAN
Handover from GSM to UTRAN accomplished. Generated after entering WCDMA mode. Handover from GSM to UTRAN failed. Successful HSPA serving cell handover. The same symbol is used as for Interfrequency Handover, since HSPA serving cell handover is handled in a similar way (and differently from UMTS soft handover).
g w
Unsuccessful HSPA serving cell handover. The same symbol is used as for Interfrequency Handover Failure (compare HS Serving Cell HO).
Idle Mode
The phone has entered idle mode. Extra information: BCCH ARFCN and BSIC.
Successful WCDMA inter-frequency cell reselection. Extra information: New UARFCN; new SC.
307
Symbol
* w
Description/Extra Information Successful WCDMA inter-frequency handover. Extra information: New UARFCN.
Inter-frequency Handover Failure Intra-frequency Hard Handover Intra-frequency Hard Handover Failure Limited Service Mode Location Area Update
w w w g g w
WCDMA inter-frequency handover failed. Successful WCDMA intra-frequency hard handover. WCDMA intra-frequency hard handover failed. The GSM phone has entered limited service mode (emergency calls only). The phone has changed location areas. Extra information: Location update type (LUT). The phone failed in changing its location area. Extra information: Cause; location update type (LUT).
g w
Measurement Report 1
Intra-frequency measurement report sent from phone (UMTS reporting event e1a, etc.). Extra information: Type of UMTS event.
Measurement Report 2
Inter-frequency measurement report sent from phone (UMTS reporting event e2a, etc.). Extra information: Type of UMTS event.
Measurement Report 3
Intra-frequency measurement report sent from phone (UMTS reporting event e3a, etc.). Extra information: Type of UMTS event.
308
Symbol
* w
Description/Extra Information Measurement report containing phoneinternal measurements sent from phone (UMTS reporting event e6a, etc.). See 3GPP 25.331, section 14.6. Extra information: Type of UMTS event.
This is a GSM event based on scan data that includes decoded BSIC and System Information. The event does not require a cell file. It is assumed that the strongest cell with decoded BSIC is the serving cell. Among other cells with decoded BSIC, the six strongest ones are looked up in the strongest cells neighbor list (which is extracted from System Information messages). For each cell that is not in the neighbor list, an instance of this event is generated. The event is only generated once for each combination of assumed serving cell (ARFCN + BSIC) and missing neighbor (ARFCN). Extra information: BCCH ARFCN and BSIC of serving cell; ARFCN, BSIC, and signal strength (in dBm) of missing neighbor.
309
Symbol
* w
Description/Extra Information This is a WCDMA event based on phone data. The event does not require a cell file. Triggered in the following cases: 1. The strongest active set member lies between 18 dB and 12 dB, and the strongest detected neighbor is stronger than 12 dB. 2. The strongest active set member is stronger than 12 dB, and the strongest detected neighbor is stronger than 12 dB. 3. A detected neighbor exists, although no active set member or monitored neighbor exists. The signal strength measure used in the comparisons is CPICH Ec/No. Extra information: Cases 1 and 2 above: Priority (1 and 2 respectively); strongest active set member SC and Ec/No; missing neighbor SC and Ec/No. Case 3: Missing neighbor SC and Ec/ No.
310
Symbol
* (c) sw
Description/Extra Information This event is based on scan data in WCDMA. It requires either that the scan data includes decoded SIBs, or that a cell file is loaded and that the currently strongest cell has a neighbor list defined in that file.
If both SIB and cell file data are available, the SIBs are used and the cell file is ignored. Triggered in the following cases: 1. A cell not defined as a neighbor of the strongest cell is more than 3 dB stronger than at least one neighbor of the strongest cell. 2. A cell not defined as a neighbor of the strongest cell is within 3 dB of the strongest cell. (The event is then triggered regardless of the strength of defined neighbors.) 3. No cell from the strongest cell's neighbor list is detected, but at least one cell is detected besides the strongest cell. (The event is then triggered regardless of the strength of that cell.) The signal power measure used in the comparisons is Aggr Ec. Extra information: UARFCN plus the following (different for each of the three cases listed above): 1. Defined neighbor SC and Ec/Io; missing neighbor SC and Ec/Io. 2. Strongest cell SC; missing neighbor SC and Ec/Io. 3. Strongest cell SC; missing neighbor SC.
311
Symbol
* g
Description/Extra Information This is a GSM event based on phone data. It does not require a cell file. Triggered in when the source cell of a handover is not in the target cells neighbor list. Cells are compared with respect to ARFCN and BSIC. If BSIC is not available, the event will not be triggered. The event triggering is delayed two seconds after the handover to ensure that the entire neighbor list of the target cell has been received. Extra information: Serving cell ARFCN and BSIC (i.e. new serving cell after handover); missing neighbor ARFCN and BSIC (i.e. old serving cell prior to handover).
This event is based on scan data in WCDMA. The information element Poss No of AS Members (with argument = power threshold 3 dB) is larger than 3, and all the detected scrambling codes are stronger than 100 dBm. Extra information: UARFCN.
g g
The phone has entered no service mode, since it cannot find a control channel. The phone has entered packet mode (it has switched to a PDCH). Extra information: BCCH ARFCN and BSIC.
312
Symbol
* g w
Description/Extra Information A PDP context has been successfully activated. Extra information: Setup time, counted from the first RRC Connection Request message to Activate PDP Context Accept. PDP context completion time, counted from the first Activate PDP Context Request message to Activate PDP Context Accept.
PDP Context Activation Failure PDP Context Deactivation PDU Error PS Attach
g w g w g g w
Activation of a PDP context failed. Extra information: Failure cause. An active PDP context has been deactivated. Protocol Data Unit error caused by syntax error in Layer 3 message. The phone successfully attached to the packet service. Extra information: Attach type; attach completion time.
PS Attach Failure
g w
The phone failed to attach to the packet service. Extra information: Attach type; failure cause.
A switch between a dedicated data channel and a common data channel succeeded. Extra information: Direction of switch: Dedicated to Common or Common to Dedicated.
313
Symbol
* w
Description/Extra Information A switch between a dedicated data channel and a common data channel failed. Extra information: Direction of switch: Dedicated to Common or Common to Dedicated.
g w w
The phone successfully detached from the packet service. The spreading factor, and hence the data rate, was changed successfully for the radio access bearer. Extra information: Uplink and downlink spreading factors.
A change of spreading factor failed for the radio access bearer. Extra information: Uplink and downlink spreading factors.
RACH Error
A RACH error was triggered because no RRC Connection Request was sent after initiation of a voice call by a command sequence. The phone could not reconfigure the radio bearer. Extra information: Cause value.
The phone could not set up the radio bearer. Extra information: Cause value.
One or several radio links have been added. Extra information: Added scrambling codes; soft handover type; event type.
Addition of one or several radio links failed. Extra information: Failure cause.
314
Symbol
* w
Description/Extra Information One or several radio links have been removed. Extra information: Removed scrambling codes; event type.
Removal of one or several radio links failed. Extra information: Failure cause.
Combined addition and removal of radio links. Extra information: Added scrambling codes; removed scrambling codes; soft handover type; event type.
Addition or removal of one or several radio links failed. Extra information: Failure cause.
g g w g w
The GSM phone is emitting a ringing signal. The phone has changed routing areas. The phone failed in changing its routing area. Extra information: Failure cause.
Rove In To GAN
ga
Successful reselection from GSM to GAN. Triggered by GAN Layer 3 message Register Accept.
ga
Reselection from GSM to GAN failed. Triggered by GAN Layer 3 message Register Reject or by the TU3904 timer expiring after Register Request is sent. Extra information: Failure cause.
315
Symbol
* ga
Description/Extra Information When reselecting from GSM to GAN, the phone was redirected from the default GANC to a different GANC. Triggered by GAN Layer 3 message Register Redirect.
ga
Successful reselection from GAN to GSM. Triggered by GAN Layer 3 message Deregister.
ga
Reselection from GAN to GSM failed. Triggered when GA-RC/GA-CSR State switches to Deregistered without Deregister message being received.
RRC Connection Reject RRC Established (green) RRC Protocol Error (red) Scanning Mode
sg
The GSM phone has entered scanning mode, i.e. it has started some type of scanning. A security mode command failed. Extra information: Cause value.
Soft handover: Active set update procedure completed with Measurement Control message.
316
Symbol
* w
Description/Extra Information Soft handover: Active set update procedure completed without a Measurement Control message (because another soft handover procedure started). Extra information: Addition/Removal/ Replacement.
Silent Call
g w
A silent call was detected by the AQM algorithm: all system signaling was OK, but the audio was not transferred in both directions. The event is triggered 27.5 s after the last Stop DTMF Acknowledge message. See the document AQM in TEMS Products (Including PESQ).
SMS Error SMS Received SMS Sent T200 Expired T3126 Expired T3162 Expired T3168 Expired T3170 Expired
g w g w g w g g g g g
Transfer of an SMS message failed (during either sending or receiving). An SMS message was successfully received. Sending of an SMS message was successfully competed. A Layer 2 Timeout occurred. A Channel Request Timeout occurred. A Packet Queuing Timeout occurred. A Packet Assignment Timeout occurred. A Packet Channel Request Timeout occurred.
317
7.3.
CDMA Events
Event Name Symbol Description/Triggered By Unexpected change to idle or init state before Call Established, or Order (PCH) Message received with one of the order codes Reorder, Intercept, Registration Reject, or Release. MO call: Origination (ACH) message sent with a voice Service Option. MT call: Page Response (ACH) message received with a voice Service Option. A call attempt (see Call Attempt above) was repeated. Triggered by Order (RTCH) Message or Order (FTCH) Message with order code = Release. MO call: Triggered by Service Connect Completion (RTCH) Message. MT call: Order (RTCH) Message with order code = Connect. Triggered by Protocol Report containing dialed number. A call has been set up by the phone. Triggered by Service Connect Completion (RTCH) Message. The phone is in traffic state. Unexpected change to idle or init state after Call Established. The phone suspended the EV-DO service to look for 1x paging. Triggered by EV-DO Tuneaway Information Report.
318
Symbol
Description/Triggered By An EV-DO access attempt completed successfully. Triggered by EV-DO Access Attempt Report.
An EV-DO connection attempt failed. Triggered by EV-DO Connection Attempt Report. An EV-DO connection attempt completed successfully. Triggered by EV-DO Connection Attempt Report.
The phone switched back from fixed rate to dynamic rate during an EV-DO session. Triggered by occurrence of fixed rate end time (see EV-DO Fixed Rate).
The phone has entered fixed rate mode for a period of time during an EV-DO session. Triggered by receipt of Fixed Mode Enable Message (containing a given end time).
EV-DO Handoff 1 Active EV-DO Handoff 2 Actives EV-DO Handoff 3 Actives EV-DO Handoff 4 Actives EV-DO Handoff 5 Actives EV-DO Handoff 6 Actives
EV-DO active set reduced to a single pilot. Handoff in EV-DO traffic mode, two pilots in active set. Handoff in EV-DO traffic mode, three pilots in active set. Handoff in EV-DO traffic mode, four pilots in active set. Handoff in EV-DO traffic mode, five pilots in active set. Handoff in EV-DO traffic mode, six pilots in active set.
319
Symbol
Description/Triggered By There is only a single active pilot and no candidates. Triggered by EV-DO Pilot Sets Ver2 Report.
An EV-DO session attempt failed. Triggered by EV-DO Session Attempt Ver2 Report. An EV-DO session attempt completed successfully. Triggered by EV-DO Session Attempt Ver2 Report.
Hard Handoff
Handoff in traffic state to another frequency, a different band, a different pilot set, or another frame offset, or a combination of these. Triggered by Active Set Change.
Idle Handoff
System change from 1x or EV-DO to Analog in idle mode. Triggered by System Determination Last Main Action Report.
System change from Analog or EV-DO to 1x in idle mode. Triggered by System Determination Last Main Action Report.
System change from 1x to EV-DO in idle mode. Triggered by System Determination Last Main Action Report. The phone is in init state or has entered idle mode.
Idle Mode
320
Symbol
(olive green bar on the right) No Service Mode Packet Mode Polluter (red bar on the right) Soft Handoff 2-Way Soft Handoff 3-Way Soft Handoff 4-Way Soft Handoff 5-Way Soft Handoff 6-Way Soft Handoff Complete Traffic Handoff To Analog Soft handoff in 1x traffic mode, two pilots in active set. Soft handoff in 1x traffic mode, three pilots in active set. Soft handoff in 1x traffic mode, four pilots in active set. Soft handoff in 1x traffic mode, five pilots in active set. Soft handoff in 1x traffic mode, six pilots in active set. Active set in 1x reduced to a single pilot. System change from 1x to Analog during traffic. Triggered by System Determination Last Main Action Report. The mobile is searching for serving network, or is in sleep mode. The phone has entered data traffic mode. See algorithm description in section 7.3.1.
321
Symbol
Description/Triggered By System change from Analog or EV-DO to 1x during traffic. Triggered by System Determination Last Main Action Report.
System change from 1x to EV-DO during traffic. Triggered by System Determination Last Main Action Report.
322
7.3.1.
1. Order all pilot responses by descending . Discard pilots that lie below the noise floor (which is technology and frequency band dependent). 2. Identify all pilots whose strength exceeds . 3. Let , where is the maximum number of fingers that a receiver can demodulate. 4. For , check whether the strongest pilot is in the neighbor list. Any pilot not in the neighbor list is flagged as a missing neighbor. 5. Calculate , where
6. Calculate
where
7. Calculate the percentage of useful energy 8. If 9. If polluter. , there is no pilot pollution. , then each pilot such that
. is a
323
7.4.
Data Events
A response to a Ping Request was received. Extra information: Ping delay Ping size
Ping Timeout
A Ping Request timed out. Extra information: Ping timeout notification Ping size
PS Access Failure
The packet-switched access procedure failed somewhere between RAS Dial and IP Address Assigned. The packet-switched access procedure succeeded from RAS Dial to IP Address Assigned. A RAS dial-up has been performed.
PS Access Success
RAS Dial
324
Symbol
Description/Extra Information An error occurred when performing a RAS dialup. Extra information: Failure cause; see DC UM section 14.21.2.
A RAS hangup has been performed. A data session has ended. Extra information: Session duration (If Ping was run during the session:) Total number of pings; number of successful pings; mean ping delay.
Session Error
A data session was interrupted because of an error. Extra information: Failure cause; see DC UM section 14.21.
Session Start
The state of the streaming video client in TEMS Investigation has changed. Extra information: State of streaming video client. One of Connecting, Negotiating, Prebuffering, Reproducing, Rebuffering, Finished.
325
8.
This chapter explains the purpose of each window found on the Menu tab of the Navigator in Data Collection as well as Route Analysis. The set of presentation windows is nearly identical in the two applications; where differences occur, they are pointed out below. Note that only windows covered by your license will show up in the applications. For example, if your license does not cover CDMA or EV-DO, all windows containing CDMA or EV-DO data will be hidden.
8.1.
8.1.1.
GPS
8.1.2.
8.1.2.1.
326
Description Shows information on an ongoing data session governed by a command sequence. (This window is common to all technologies.) Shows data that is relevant to EV-DO, including PER and RLP layer performance. Shows statistics on good and bad packets for each forward link data rate. Shows statistics on good and bad packets for each reverse link data rate.
EV-DO Overview
8.1.2.2.
Window Name A/C/N Sets Active Set Candidate Set Finger Info Neighbor Set Radio Parameters
327
Description Shows various IDs, states, and parameter settings of the current serving cell. Shows FER, PESQ, and Frequent AQM. See DC UM chapter 29.
8.1.3.
8.1.3.1.
The information in these windows is obtained when running GPRS, EDGE, or HSCSD. Some of the information (everything in the Data Session window, and some parameters in other windows) is only shown when a data testing command sequence is being executed or replayed. Window Name Data Bytes Sent/Received Data Session Description Shows the total number of data bytes sent and received at various protocol levels. Shows information on an ongoing data session governed by a command sequence. (This window is common to all technologies.) Shows current throughput and decode error/retransmission rates for GPRS/ EGPRS. Shows the timeslots currently used on the uplink and downlink for GPRS/EGPRS or HSCSD, as well as the utilization, performance, and channel coding/ modulation coding scheme usage for each timeslot. Shows the current state and performance of the EGPRS connection.
Data Throughput
Data Timeslots
EGPRS Status
328
Description Shows the current state and performance of the GPRS connection. Shows current throughput and error/ retransmission rates for HSCSD. Shows current PDP context data for GPRS/EGPRS, including quality-ofservice requirements specified in the subscription.
8.1.3.2.
8.1.3.3.
Window Name Uplink Neighbors Uplink Radio Parameters Uplink Serving Cell
329
8.1.3.4.
AMR Settings
Current Channel
GAN Status
330
Description Shows a collection of vital facts about the status of the radio link (current BCCH, signal strength, speech quality, and so on). For particulars of the information elements listed, see sections 3.1 and 4.2. Shows BSIC, ARFCN, RxLev, and some further parameters for the serving cell and its neighboring cells, with the serving cell on top and the neighbors below it, sorted by signal strength in descending order. Similar to Serving + Neighbors except that the cells are sorted first by frequency band and then by signal strength in descending order. Shows SQI, PESQ, and Frequent AQM. See DC UM chapters 28 and 29. (This window is common to GSM and WCDMA.)
Serving + Neighbors
Speech Quality
8.1.4.
8.1.4.1.
The information in these windows is obtained when testing data services. It is only shown when a data testing command sequence is being executed or replayed. Window Name Data Session Description Shows information on an ongoing data session governed by a command sequence. (This window is common to all technologies.)
331
Description Shows information elements related to DVB-H. See section 3.2 for definitions of the information elements. Shows information elements related to HSDPA. See section 4.3.6 for definitions of the information elements. Shows information elements related to HSUPA. See section 4.3.7 for definitions of the information elements. Shows current PDP context data for WCDMA, including quality-of-service requirements specified in the subscription.
HSUPA Analysis
PDP Context
8.1.4.2.
CPICH Data
Network Search
332
8.1.4.3.
Shows measurements of GSM neighbors performed in WCDMA mode. Shows information on handovers: indication of handover type (hard, soft, softer) and real-time statistics on handover frequency, success rate, and distribution across soft handover types. See sections 4.3 and 5.3 for precise definitions of the information elements shown. These windows give the essentials of Measurement Control reports, which tell the UE what should trigger the sending of a measurement report to the network. Separate windows are provided for intrafrequency, inter-frequency, and inter-RAT criteria. Shows the current state of the userconfigurable WCDMA properties for the phone: see DC UM chapter 15. Shows information on the number of RACH preambles and their transmit power.
Inter-Freq Meas Ctrl Events, Inter-RAT Meas Ctrl Events, Intra-Freq Meas Ctrl Events
Modified MS Behavior
RACH Analysis
333
Description Shows a collection of information elements describing the status of the radio link and some more general radio conditions. Details about the elements are found in sections 4.3 and 5.3. RAT State shows which radio access technology is currently used: GSM or WCDMA. Shows data on the serving cell/active set and on the monitored neighboring cells. Shows SQI, PESQ, and Frequent AQM. See DC UM chapters 28 and 29. (This window is common to GSM and WCDMA.) Shows data on each transport channel for the period of time following the latest mode report.
Transport Channels
8.1.5.
Scanned Cells
8.1.6.
334
8.1.7.
iDEN Status
8.2.
A preconfigured Event Counter window is found in the Analysis folder. Regarding Event Counter windows in general, see DC UM chapter 19.
8.3.
8.3.1.
8.3.2.
335
8.3.3.
Data Reports
Error Reports
Lists reports from the external device concerning malfunctions and received corrupt messages. The Event and Column tabs are absent from the properties dialog of this window (DC UM sections 20.1.320.1.4). Lists all events that occur, both predefined and user-defined. All predefined events are listed in chapter 7 of this volume; how to create user-defined events in each of the two applications is covered in DC UM section 16.3 and in RA UM section 4.3. As in other message windows, you can double-click an event in the Events windows to view details on the event in a separate plain-text window. For certain events, extra information is provided. The contents of this extra information are detailed in chapter 7.
Events
336
Description Lists all air interface message traffic occurring over the protocols in the Internet protocol suite: Application layer: BOOTP, DNS, FTP, FTP-DATA, HTTP, NBDS, NBNS, RTCP, RTP, RTSP, SNMP Transport layer: TCP, UDP Network layer: ICMP, IPv4, IPv6 Data link layer: PPP CC, PPP CHAP, PPP IPCP, PPP LCP, PPP PAP
Layer 2 Messages
Lists Layer 2 messages. By default this window also shows certain events, the emphasis being on call, handover, and failure events. Lists Layer 3 messages. By default this window also shows certain events, the emphasis being on call, handover, and failure events. Lists (vendor-specific) reports from external devices concerning their status. By default this window also shows certain events, the emphasis being on call, handover, and failure events.
Layer 3 Messages
Mode Reports
8.3.4.
iDEN Messages
8.4.
337
8.5.
8.5.1.
8.5.2.
338
Window Name Uplink Line Chart (Data Collection only) Video Streaming Line Chart
Description Presents data from MTR files (signal strength and power level). See DC UM chapter 33. Tracks the performance of a video streaming session, including VSQI. (This line chart is common to GSM and WCDMA.)
8.5.3.
CPICH Scan 1st (etc.) UARFCN Line Chart DVB-H Stats Line Chart HSDPA Stats Line Chart HSUPA Stats Line Chart RLC AM Stats Line Chart: Qualcomm RLC Stats Line Chart Trsp Ch Throughput Line Chart: Sony Ericsson Video Streaming Line Chart
339
Description Tracks data service performance for WCDMA R99 and (E)GPRS, including application and RLC layer throughput as well as data service testing events. Tracks data service performance for WCDMA R99, including application and RLC layer throughput as well as data service testing events. Tracks CPICH and GSM neighbor signal strength, UE transmit power, and SQI. Similar to WCDMA Line Chart, but also tracks GSM neighbor signal strength.
8.5.4.
8.5.5.
340
8.5.6.
8.6.
8.6.1.
PN Scan 1st (etc.) RF Bar Chart Polluters Bar Chart RSSI Scan Bar Chart Spectrum Analysis Bar Chart Strongest Scanned PN Bar Chart
341
8.6.2.
Interference Bar Chart (Data Collection only) Radio Quality Bar Chart (Data Collection only) RSSI Scan Bar Chart Spectrum Analysis Bar Chart
8.6.3.
HSDPA PDSCH Codes Bar Chart HSDPA Transport Block Size Bar Chart Radio Parameters Bar Chart Radio Parameters Parallel Bar Chart
342
Window Name CPICH Scan 1st (etc.) UARFCN Bar Chart, RSSI Scan Bar Chart, SCH Timeslot Scan Bar Chart, Spectrum Analysis Bar Chart, Spectrum Analysis Uplink Bar Chart
Description These charts show various kinds of WCDMA scan data. See DC UM sections 10.210.5.
8.6.4.
Enhanced Power Scan Bar Chart RS 1st (etc.) EARFCN Bar Chart RSSI Scan Bar Chart Spectrum Analysis Bar Chart
8.6.5.
Channel RSSI Bar Chart RSSI Scan Bar Chart Preamble Power Group Bar Chart Segment Power Group Bar Chart
343
Window Name Spectrum Analysis Bar Chart Strongest CINR Bar Chart Strongest Preamble Power Bar Chart Strongest Preamble Power Group Bar Chart Strongest Segment Power (Cha Sort) Bar Chart Strongest Segment Power (Segment Pwr Sort) Bar Chart Weakest CINR Bar Chart Weakest Preamble Power Bar Chart
Description Shows the result of a spectrum scan. Shows detected preambles ranked by decreasing CINR. Shows detected preambles ranked by decreasing power. Shows detected preambles grouped by channel. Channels are ranked by total preamble power. Shows segments grouped by channel. Channels are ranked according to the power of their strongest segment. Shows segments ranked by decreasing power, regardless of channel. Shows detected preambles ranked by increasing CINR. Shows detected preambles ranked by increasing power.
8.7.
Preconfigured Maps
In both applications, a map window is supplied that is configured with some basic GSM, WCDMA, and CDMA information.
8.8.
See DC UM chapter 22. In Route Analysis a status window is provided for GPS data; see section 8.1.1.
344
8.9.
The Template folder in the Navigator contains blank templates for: status windows Event Counter windows (Data Collection only) message windows (Data Collection only) line charts bar charts.
These templates contain no data; you customize their contents from scratch.
345
Appendix A. Abbreviations
ACR AG AGC ALMP AM AMR AMR-WB APM AQM ARFCN AS ASP AT BCC BCCH BCH BEP BER BLEP BLER BOOTP BSIC BSN C/A C/I C/N CBCH CDMA CFO CGI CHAP CI CINR CPI CPICH Absolute Category Rating Absolute Grant Automatic Gain Control Air Link Management Protocol Acknowledged Mode Adaptive Multi Rate Adaptive Multi Rate Wideband Advanced Power Management Audio Quality Measurement Absolute Radio Frequency Channel Number Active Set Active Set Pilot Access Terminal Base Station Colour Code Broadcast Control Channel Broadcast Channel Bit Error Probability Bit Error Rate Block Error Probability Block Error Rate Bootstrap Protocol Base Station Identity Code Block Sequence Number Carrier-to-Adjacent (Ratio) Carrier-to-Interference (Ratio) Carrier-to-Noise (Ratio) Cell Broadcast Channel Code Division Multiple Access Carrier Frequency Offset Cell Global Identity Challenge Handshake Authentication Protocol Cell Identity Carrier to Interference-plus-Noise Ratio Cell Parameter Identity Common Pilot Channel
346
Appendix A. Abbreviations
CQI CRC CS CSD CW DCCH DCD DCH DGPS DL DNS DPCCH DPCH DR DRC DRX DSC DSC DSCH DTX DVB-H E-AGCH EARFCN ECP E-DCH EDGE E-DPCCH E-DPDCH EFR EGPRS E-HICH EIRP E-RGCH ESN ESS E-TFCI EV-DO (1xEV-DO) EVRC FACCH FACH FCH FER
Channel Quality Indicator Cyclic Redundancy Check Coding Scheme Circuit-Switched Data Continuous Wave Digital Control Channel Downlink Channel Descriptor Dedicated Channel Differential GPS Downlink Domain Name System (Service, Server) Dedicated Physical Control Channel Dedicated Physical Channel Dead Reckoning Data Rate Control Discontinuous Reception Data Source Control (CDMA) Downlink Signalling Counter (GSM) Downlink Shared Channel Discontinuous Transmission Digital Video Broadcasting Handheld E- (Enhanced) Absolute Grant Channel E-UTRA ARFCN Extended Cyclic Prefix E- (Enhanced) Enhanced Dedicated Channel Enhanced Data Rates for GSM Evolution (= EGPRS) E- (Enhanced) Dedicated Physical Control Channel E- (Enhanced) Dedicated Physical Data Channel Enhanced Full Rate Enhanced GPRS (= EDGE) E- (Enhanced) HARQ Acknowledgement Indicator Channel Effective Isotropic Radiated Power E- (Enhanced) Relative Grant Channel Electronic Serial Number Extended Service Set E- (Enhanced) Transport Format Combination Indicator 1x Evolution-Data Optimized Enhanced Variable Rate Codec Fast Associated Control Channel Forward Access Channel Fundamental Channel Frame Erasure Rate
347
FL FPC FR FWT GA-CSR GAN GANC GA-RC GERAN GGSN GMM GPRS GPS GRR GSM HARQ HO HR H-RNTI HSCSD HSDPA HS-DSCH HSN HSPA HS-PDSCH HS-SCCH HSUPA IE IMEI IP IPCP ISCP JPEG KML KPI LA LAC LAT LCP LLC LON LTE
Forward Link Forward Power Control Full Rate Fixed Wireless Terminal Generic Access Circuit Switched Resources Generic Access Network Generic Access Network Controller Generic Access Resource Control GSM EDGE Radio Access Network Gateway GPRS Support Node GPRS Mobility Management General Packet Radio Service Global Positioning System GPRS Radio Resource Global System for Mobile Communication Hybrid Automatic Repeat Request Handover Half Rate HS-DSCH Radio Network Temporary Identity High Speed Circuit-Switched Data High Speed Downlink Packet Access High Speed Downlink Shared Channel Hopping Sequence Number High Speed Packet Access High Speed Physical Downlink Shared Channel High Speed Shared Control Channel High Speed Uplink Packet Access Information Element International Mobile Equipment Identity Internet Protocol Internet Protocol Control Protocol Interference Signal Code Power Joint Photographic Expert Group Keyhole Markup Language Key Performance Indicator Location Area Location Area Code Latitude Link Control Protocol Logical Link Control Longitude Long Term Evolution
348
Appendix A. Abbreviations
LUT M2M MAC MCC MCS MDM MFER MIMO MIN MM MMS MMSC MN MNC MO MOS MRU MS MSM MSTR MT MTR MTU MuxPDU NBDS NBNS NCC NDIS NID NMEA NMO NV OFDM OVHD PA PACA PAP PBCCH PCCCH P-CCPCH PCH PCI
Location Update Type Mobile To Mobile Medium Access Control Mobile Country Code Modulation Coding Scheme Mobile Diagnostic Monitor Frame Error Rate after MPE-FEC decoding Multiple Input Multiple Output Mobile Identity Number Mobility Management Multimedia Messaging Service MMS Center Monitored Neighbor Mobile Network Code Mobile-originated Mean Opinion Score Mobile Receiving Unit Mobile Station (may represent phone or scanner) Mobile Station Modem Mobile Station Time Reference Mobile-terminated Mobile Traffic Recording Mobile Test Unit Multiplex Sublayer Protocol Data Unit NetBIOS Datagram Service NetBIOS Name Service Network Colour Code Network Driver Interface Specification Network Identification National Marine Electronics Association Network Mode of Operation Non Volatile Orthogonal Frequency-Division Multiplexing Overhead Power Amplifier Priority Access and Channel Assignment Password Authentication Protocol Packet Broadcast Control Channel Packet Common Control Channel Primary Common Control Physical Channel Paging Channel Physical layer Cell Identity
349
PCIG PCS PDCH PDP PDU PER PESQ PI PID PLMN PN POP3 PPCH PPP PPS P-SCH PSTN QAM QCELP QOF QPSK RA RAB RAC RACH RAN RAS RAT RATI RB RL RLA RLC RLP RNC RP RPC RQ RR RRC RRI RS
Physical layer Cell Identity Group Personal Communications Service Packet Data Channel Packet Data Protocol Protocol Data Unit Packet Error Rate Perceptual Evaluation of Speech Quality Performance Indicator Product ID Public Land Mobile Network Pseudo Noise Post Office Protocol version 3 Packet Paging Channel Point-to-Point Protocol Precise Positioning Service Primary Synchronisation Channel Public Switched Telephone Network Quadrature Amplitude Modulation Qualcomm Code Excited Linear Prediction Quasi-Orthogonal Function Quadrature Phase Shift Keying Routing Area Reverse Activity Bit Routing Area Code Random Access Channel Radio Access Network Remote Access Service Radio Access Technology Random Access Terminal Identifier Radio Bearer Reverse Link Received Level Average Radio Link Control Radio Link Protocol Radio Network Controller Received Power Reverse Power Control Received Quality Radio Resource (Management) Radio Resource Control Reverse Rate Indication Reference Signal
350
Appendix A. Abbreviations
RSCP RSRP RSRQ RSSI RTCP RTP RTSP SACCH SAN SAPI SC SCC SCH SCH SDCCH SDP SDU SEGW SF SG SGSN SGW SHO SIB SID SID SIM SINR SIR SMS SMTP SMV SNDCP SNR SPS SQI SS S-SCH SSID TA TAB TB
Received Signal Code Power Reference Signal Received Power Reference Signal Received Quality Received Signal Strength Indicator Real Time Control Protocol Real Time Transport Protocol Real Time Streaming Protocol Slow Associated Control Channel Serving/Active Set + Neighbors Service Access Point Identifier Scrambling Code Supplemental Code Channel Supplemental Channel (CDMA) Synchronisation Channel (UMTS) Standalone Dedicated Control Channel Session Description Protocol Signaling Data Unit Security Gateway Spreading Factor Serving Grant Serving GPRS Support Node Security Gateway Soft Handover System Information Block Silence Descriptor (UMTS) System Identification (CDMA) Subscriber Identity Module Signal to Interference plus Noise Ratio Signal to Interference Ratio Short Message Service Simple Mail Transfer Protocol Selectable Mode Vocoder Subnetwork Dependent Convergence Protocol Signal to Noise Ratio Standard Positioning Service Speech Quality Index Signal Strength Secondary Synchronisation Channel Service Set Identifier Timing Advance (umbrella term for various MapInfo file types) Transport Block
351
TBS TCA TCH TCP TDD TDMA TFI TI TIF TLLI TM TPC TS TSC TTI UARFCN UATI UCD UCS UDP UE UL UM UMA UMTS UpPCH URA URI USB UTF UTM UTRAN VID VMR-WB VSQI VTQI WAP WCDMA WiMAX WLAN WSP XML
Transport Block Size Traffic Channel Assignment Traffic Channel Transmission Control Protocol Time Division Duplex Time Division Multiple Access Temporary Flow Id Transaction Identifier Tag Image File Temporary Logical Link Identifier Transparent Mode Transmit Power Control Timeslot Training Sequence Code Transmission Time Interval UMTS Absolute Radio Frequency Channel Number Unicast Access Terminal Identifier Uplink Channel Descriptor Universal Character Set User Datagram Protocol User Equipment Uplink Unacknowledged Mode Unlicensed Mobile Access Universal Mobile Telecommunications System Uplink Pilot Channel UTRAN Registration Area Uniform Resource Identifier Universal Serial Bus UCS Transformation Format Universal Transverse Mercator UMTS Terrestrial Radio Access Network Vendor ID Variable Multi Rate Wideband Video Streaming Quality Index Video Telephony Quality Index Wireless Application Protocol Wideband Code Division Multiple Access Worldwide Interoperability for Microwave Access Wireless Local Area Network Wireless Session Protocol Extensible Markup Language
352
Index
Index
A
A/C/N Sets window (CDMA) 327 abbreviations 346 Active Set window (CDMA) 327 Adjacent Bar Chart (GSM) 342 AMR Call Average window (GSM) 330 AMR Cell Average window (GSM) 330 AMR Codecs window (WCDMA) 333 AMR Settings window (GSM) 330 AMR window (GSM) 330
B
bar charts, preconfigured 341 CDMA 341 GSM 342 LTE 343 WCDMA 342 WiMAX 343
C
C/A window (GSM) 329 C/I window (GSM) 329 Call Analysis window 335 Candidate Set window (CDMA) 327 CDMA Bar Chart 341 CDMA Data Line Chart 338 CDMA information elements in Data Collection 122 in Route Analysis 252 CDMA Line Chart 338 CDMA Polluters Bar Chart 341 Channel RSSI Bar Chart (WiMAX) 343 Channel RSSI Line Chart (WiMAX) 340 Compact Adjacent Bar Chart (GSM) 342 contents of Information Elements and Events 1
353
CPICH Best UARFCN Data window (WCDMA) 332 CPICH Data window (WCDMA) 332 CPICH Scan bar charts (WCDMA) 343 CPICH Scan line charts (WCDMA) 339 Current Channel window (GSM) 330
D
Data Bytes Sent/Received window (CDMA) 326 Data Bytes Sent/Received window (GSM) 328 Data Collection information elements 4 Data Reports window 336 data service testing information elements in Data Collection 162 in Route Analysis 282 Data Session window (common to all technologies) 327, 328, 331 Data Throughput window (GSM) 328 Data Timeslots window (GSM) 328 DVB-H Analysis window (WCDMA) 332 DVB-H Stats Line Chart (WCDMA) 339
E
EGPRS Line Chart 338 EGPRS Status window 328 Enhanced Power Scan Bar Chart (LTE) 343 Ericsson MTR Records window (GSM) 335 Error Reports window 336 EV-DO Forward Link Packets window 327 EV-DO Overview window 327 EV-DO Reverse Link Packets window 327 Event Counter windows preconfigured 335 Events window 336 events, listing of predefined 299 CDMA 318 data service testing 324 general events 299 GSM/WCDMA/TD-SCDMA 301
F
Finger Info window (CDMA) 327 Finger Info windows (WCDMA) 333
G
GAN Status window (GSM) 330
354
Index
GAN WLAN Quality Line Chart 338 GPRS Line Chart 338 GPRS Status window 329 GPS window (Route Analysis) 326 GSM information elements in Data Collection 5 in Route Analysis 171 GSM Line Chart 338 GSM Neighbors window (WCDMA) 333 GSM uplink information elements in Data Collection 166
H
Handover window (WCDMA) 333 Hopping Channels window (GSM) 330 HSCSD Throughput window 329 HSDPA Analysis window 332 HSDPA PDSCH Codes Bar Chart 342 HSDPA Stats Line Chart 339 HSDPA Transport Block Size Bar Chart 342 HSUPA Analysis window 332 HSUPA Stats Line Chart 339
I
iDEN Messages window 337 iDEN Status window 335 information elements categorization of (GSM) 171 CDMA category 3 Data category 3 Full and Sub values 7, 173 General category 2 GSM category 2 GSM Uplink category 3 in Data Collection 4 CDMA 122 data service testing 162 GSM 5 GSM uplink (MTR) 166 LTE 108 TD-SCDMA 114 WCDMA 58 WiMAX 154
355
in Route Analysis 169 CDMA 252 access probe 252 active set 253 active set EV-DO 254 candidate set 256 candidate set, EV-DO 257 channel configuration 258 data 261 finger information (1x and EV-DO) 266 finger information (EV-DO specific) 267 mobile 268 neighbor set (1x and EV-DO) 268 neighbor set (EV-DO specific) 270 pilot set 270 polluters 271 power (1x and EV-DO) 272 power (EV-DO specific) 273 radio measurement 274 scan data 276 server 277 session EV-DO 280 statistics 281 data service testing 282 general 169 GSM 171 GAN 173 GPRS/EGPRS channel 175 GPRS/EGPRS measurement 179 low level data 183 MS behavior 186 neighbors 189 quality measurement 192 scan data 197 serving cell, channels 200 serving cell, interference 203 serving cell, measurement 207 WCDMA parameters measured in GSM mode 212 WCDMA 213 active set 213 data (PDP context) 213 GSM neighbor measurements in WCDMA mode 216
356
Index
handover measurements 217 HSDPA 220 HSUPA 225 low level data 227 MS behavior 232 neighbors 233 network parameters 235 quality measurement 235 radio measurement 237 Rake finger information 214 SAN (serving cell/active set + neighbors) 239 scan data 241 serving cell 250 LTE category 3 support for in phones and scanners 286 CDMA 286 GSM 287 LTE 297 WCDMA 293 TD-SCDMA category 3 WCDMA category 3 WiMAX category 3 Interference Bar Chart (GSM) 342 Interference Line Chart (GSM) 338 Inter-Freq Meas Ctrl Events window (WCDMA) 333 Inter-RAT Meas Ctrl Events window (WCDMA) 333 Intra-Freq Meas Ctrl Events window (WCDMA) 333 IP Analysis window 337
L
Layer 2 Messages window 337 Layer 3 Messages window 337 line charts, preconfigured 338 CDMA 338 GSM 338 iDEN 341 LTE 340 WCDMA 339 WiMAX 340 LTE information elements in Data Collection 108
357
M
Map windows, preconfigured 344 message windows, preconfigured 335 analysis 335 GSM uplink data 335 iDEN 337 signaling 336 Mode Reports window 337 mode reports, plain-text decoding of 298 Modified MS Behavior window (GSM) 330 Modified MS Behavior window (WCDMA) 333 MTR information elements in Data Collection 166
N
Neighbor Set window (CDMA) 327 Network Search window (WCDMA) 332
P
PDP Context window (GSM) 329 PDP Context window (WCDMA) 332 PN Scan bar charts (CDMA) 341 PN Scan line charts (CDMA) 338 Polluters Bar Chart (CDMA) 341 Preamble Power Group Bar Chart (WiMAX) 343 presentation windows overview of preconfigured 326 templates for 345
Q
Qualcomm chipset based devices line chart for RLC statistics 339
R
RACH Analysis window (WCDMA) 333 Radio Parameters Bar Chart (WCDMA) 342 Radio Parameters Parallel Bar Chart (WCDMA) 342 Radio Parameters window (CDMA) 327 Radio Parameters window (GSM) 331 Radio Parameters window (WCDMA) 334 Radio Quality Bar Chart (GSM) 342 RAS 162 Remote Access Service (RAS) 162 RLC AM Stats Line Chart -- Qualcomm (WCDMA) 339
358
Index
RLC Stats Line Chart (WCDMA) 339 RLC/MAC header data 41 Route Analysis information elements 169 RS bar charts (LTE) 343 RS line charts (LTE) 340 RSSI Scan Bar Chart (CDMA) 341 RSSI Scan Bar Chart (GSM) 342 RSSI Scan Bar Chart (LTE) 343 RSSI Scan Bar Chart (WCDMA) 343 RSSI Scan Bar Chart (WiMAX) 343 RSSI Scan Line Chart (LTE) 340 RSSI Scan Line Chart (WiMAX) 340
S
Scanned Cells window (LTE) 334 Scanned Preamble Index window (WiMAX) 334 SCH Timeslot Scan Bar Chart (WCDMA) 343 Segment Power Group Bar Chart (WiMAX) 343 Serving + Neighbors By Band window (GSM) 331 Serving + Neighbors window (GSM) 331 Serving window (CDMA) 328 Serving/Active Set + Neighbors window (WCDMA) 334 Session Status window 335 signal power notes on quantities denoting 58 Sony Ericsson UEs line chart for transport channel throughput 339 Spectrum Analysis Bar Chart (CDMA) 341 Spectrum Analysis Bar Chart (GSM) 342 Spectrum Analysis Bar Chart (LTE) 343 Spectrum Analysis Bar Chart (WCDMA) 343 Spectrum Analysis Bar Chart (WiMAX) 344 Spectrum Analysis Uplink Bar Chart (WCDMA) 343 Speech Quality window (CDMA) 328 Speech Quality window (GSM/WCDMA) 331, 334 status windows, preconfigured 326 CDMA 326 data service testing 326 general 326 GSM 328 data service testing 328 interference 329 uplink data 329
359
iDEN 335 LTE 334 WCDMA 331 data service testing 331 scanning 332 WiMAX 334 Strongest CINR Bar Chart (WiMAX) 344 Strongest Preamble Power Bar Chart (WiMAX) 344 Strongest Preamble Power Group Bar Chart (WiMAX) 344 Strongest Scanned PN Bar Chart (CDMA) 341 Strongest Segment Power (Cha Sort) Bar Chart (WiMAX) 344 Strongest Segment Power (Segment Pwr Sort) Bar Chart (WiMAX) 344 Synch Channel Data window (WCDMA) 332
T
TD-SCDMA information elements in Data Collection 114 TPC per Cell mode report (Sony Ericsson) 298 Transport Channels window (WCDMA) 334 Trsp Ch Throughput Line Chart -- Sony Ericsson (WCDMA) 339
U
Uplink Line Chart (GSM) 339 Uplink Neighbors window (GSM) 329 Uplink Radio Parameters window (GSM) 329 Uplink Serving Cell window (GSM) 329
V
Video Streaming Line Chart (GSM/WCDMA) 339
W
WCDMA Handover Analysis window 335 WCDMA HSPA/GSM Data Line Chart 339 WCDMA information elements in Data Collection 58 in Route Analysis 213 WCDMA Line Chart 340 WCDMA Missing Neighbor window 336 WCDMA Rel. 99/GSM Data Line Chart 340 WCDMA RLC Data Line Chart 340 WCDMA/GSM Line Chart 340 Weakest CINR Bar Chart (WiMAX) 344 Weakest Preamble Power Bar Chart (WiMAX) 344
360
Index
361
TEMS Optimization Solutions the number one choice for operators worldwide. For every stage of a wireless networks life cycle and supporting all major technologies, the TEMS portfolio helps operators maximize their Quality of Service and get the most out of their network investment. The experience and technological leadership of TEMS gives network operators the strong partnership they need and a commitment to quality, accuracy, and success. TEMS Optimization Solutions Making Wireless Better.