Professional Documents
Culture Documents
Water Tite 101
Water Tite 101
aw@fEgCflElN
PIONEER PRO Water-Tite 101 is a crystalline capillary waterproofi ng formulation of selected blends ofcement,fine quartz sand and active chem ical constituents providing a lasting imperuiousness to water
achieved.Allow the mix to rest for l5 minutes to allow for chemi<a I reaction. lt should then adhere to the brush without dripping.lf mixture thickent re-stir to reduce consistency.Do not add extra water
frruwg
BArrurflet
Prior to the
a
pplication of
pplications
painted over
substrates
Water-Tite 101 slurry coat may be applied with a brush or broom.Be sure to work slurry into the openingt roug h sufaces,ioints and routed out areas.Apply second coat,when required, when first coat hastaken an initial set.
,tuArGdrrot
Water-Tlte '101 can be applied on both new and old structu res either on water retaining sideoron the negative side.P|ONEER PRO Water-Tite l0'l is recommended forthe following typical a pplications: . Water treatment or sewage structures
PIONEER PRO
Tunnels,silos,water tanks
from the container Wearing rubberglovet distributethe powder evenly by hand over freshly poured concrete 1.25 to l.35kg/m, per application before final trowelling works.lt is best to distribute the powder at the ', recommended late in one direction,and the other halfata right angle to the first application. Release the powder as close to the wet concrete as possible to prevent material from
&MrcEarEPt rTot
.
concrete sudace to be treated mu5t be free and clean of laitancgdirt, paint coating and other foreign matter
blowing away. Twoapplications are recommended with a roughened finish on thefirst application providing adeq uate adhesion ofthe second
a
EffiW
When the last coat has stiffened, float it to desired texture with a sponge or wood float.
blasting.
. Structural defects such as crack, faulty
C@ e tWrDerEEllCl
Proper curing proced ures are im portant to ensure the durability and qualityofthe coating. To prevent surface cracking,curing must begin
as
with
PIONEER PRO
separatedata sheet). . Saturate routed area and leavedampfor application of water-Tite l0l.
PRO
Water-Tite 101
DZJC
SlurryCo.t
Mix4.54 K9 can
PIONEER PRO
Water-Tite 101
coating has reached initia I set. Moist curing using continuous water spray is recommended. Keep PIONEER PRO Water-Tite 101 treatments moist and cured fora minimum of 48 hours by spraying surfaces with a fine mist of water three
timesadayfor2-3days.lnwarmerclimatet
more frequent spraying may be required.
ffi*Ibfrl
GrrrurtnM,
PIONEER PRO
'iffi##iifo'*'
Water-Tite l0l slurry coat: l.Gl.3k9/m, at 2 coats. Note Actual coverage rates willdepend upon the profileand porosity ofthe substrate.
AIOME
PIONEER PRO
WateFTite
l0l
should be stored
in protected dryareas.The shelflife is l2 months in its orjginalunopened packing in a coolventilated place below 35.C in a shaded dryenvironment. Do not store in direct sunlight.
a*grarlffi
Do not use PIONEER PRO water-Tite
l0lover
previous coated 5urfacewithout proper sudace preparation. Freshly applied PIONEER PRO Water-Tite 101 treatment must be protected from exteme weather conditions such as rain or high temperaturefora period ofnot lessthan 48 hou15 after application. For water retaining structures PIONEER PRO Water-Tite 101 treatmentshould be cured for
Mu7trmffi7r
101 may contain chemicals that may cause irritation to the eyes and skin.Goggles, face mask, rubber gloves and long sleeves
Water{ite
EM
PIONEER PRO
Water-Tite
l0l
is non-flammable.
,ran crte
Available in4.54 Kg canand 25 Kg bag.
nEPUBUC CHEIUIGAI il0USTBtES, tXG. 731 AurcG Blvd., aleo City, I I l2 Philippine
Mdb +r 593 b 95/72r-57r l Prcvimi.I l-30G1333{261 Ooll Fe) We6site wwJepchem.com ^,lahila:4r
For Prcdod lnfdmatron: