Professional Documents
Culture Documents
Cisco Switch Configuration Template For Aastra Phones: Advanced Technical Assistance Center (ATAC)
Cisco Switch Configuration Template For Aastra Phones: Advanced Technical Assistance Center (ATAC)
Version 1.1
Advanced Technical Assistance Center (ATAC)
14111 Capital Boulevard Wake Forest, NC 27587
CenturyLink Confidential
Document History
Date 3/17/2010 3/25/2010 Version 1.0 1.1 Editor Dan Boutieller Dan Boutieller Change Initial document Added Aastra firmware version
Advanced Technical Assistance Center Cisco Switch Configuration Template for Aastra Phones
Table of Contents
Table of Contents................................................................................................................ 3 1 Introduction............................................................................................................. 4 2 IOS Versions........................................................................................................... 4 3 Aastra Phone Firmware Version............................................................................. 4 4 Dynamic Host Configuration Protocol (DHCP) Settings ....................................... 4 5 Enabling LLDP-MED............................................................................................. 5 6 Enabling QOS ......................................................................................................... 5 7 Interface Configuration........................................................................................... 5 8 Optional Commands ............................................................................................... 6 8.1 TFTP Server................................................................................................ 6 8.2 8.3 8.4 NTP Server.................................................................................................. 6 LLDP Timer Work Around ........................................................................ 6 Inline Power Consumption Changes........................................................... 6
Advanced Technical Assistance Center Cisco Switch Configuration Template for Aastra Phones
Introduction
The information contained in this guide was discovered through comprehensive testing. These settings provide a basic template for the deployment of Aastra phones with Metaswitch in a Cisco LAN environment. It is assumed that the customers infrastructure contains either Cisco 2960, 3560, or 3750 switches. This is basic template that does not contain some of the advanced configuration options that are available in the switching IOS.
2 IOS Versions
The IOS that is required to support LLDP-MED will be version 12.2(44)SE or higher. This was when the protocol was first supported and is requirement for the Aastra phones to properly connect to the network.
* A copy of the Aastra.cfg file will need to be copied to the TFTP server specified in the scope.
Switch(config)#ip dhcp pool data_VLAN Switch(dhcp-config)#network 10.1.46.0 255.255.255.0 Switch(dhcp-config)#default-router 10.1.46.1 Switch(dhcp-config)#dns-server <DNS IP ADDRESS>
5 Enabling LLDP-MED
The following command is the only one required to enable LLDP-MED. This command is run in global configuration mode. Switch(config)#lldp run
6 Enabling QOS
The following command should be used to enable QOS and is run globally. Any additional commands will be determined by the customers infrastructure. Switch(config)#mls qos
7 Interface Configuration
The following configuration example is for interfaces that Aastra phones will connect to. It is also assumed that there will be a PC plugged into the PC port of the phone. Note that VLAN 200 and VLAN 300 are examples and can be any VLAN number. They are normally determined by the customers existing infrastructure.
Switch(config)#interface GigabitEthernet0/1 Switch(config-if)#description Aastra phone interface Switch(config-if)#switchport access vlan 300 Switch(config-if)#switchport mode access Switch(config-if)#switchport voice vlan 200 Switch(config-if)#mls qos trust dscp Switch(config-if)#spanning-tree portfast
Advanced Technical Assistance Center Cisco Switch Configuration Template for Aastra Phones
8 Optional Commands
8.1 TFTP Server
This command is only necessary if the local switch is going to act as the TFTP server. A copy of the Aastra.cfg file will need to be copied into the flash of the switch in order for this to work. Switch(config)# tftp-server flash:aastra.cfg
Advanced Technical Assistance Center Cisco Switch Configuration Template for Aastra Phones
This command can be run globally or per interface. If there are other non-Aastra POE devices plugged into the switch the command should be run on a per interface basis and only run on the interfaces that an Aastra phone will be plugged into. Switch(config)#interface GigabitEthernet0/1 Switch(config-if)# power inline consumption 7700
Advanced Technical Assistance Center Cisco Switch Configuration Template for Aastra Phones