Professional Documents
Culture Documents
Design of Equipment Foundations
Design of Equipment Foundations
Design of Equipment Foundations
FOUNDATIONS
WAQAS RIAZ
08-NOV-2007
INDUSTRIAL EQUIPMENTS:
HORIZONTAL VESSELS
VERTICAL VESSELS
PACKAGE EQUIPMENTS
MACHINERY EQUIPMENTS
HORIZONTAL VESSELS:
General Overview
Foundation Type & Shape
Design Data
Loads Applied to Pedestal
HORIZONTAL VESSELS:
General Overview: Horizontal Vessels mainly Includes Heat Exchangers &
Drums. Foundation Type is similar for both of them.
A heat exchanger is a device used to transfer heat from one
fluid to another while preventing the two from intermingling.
The three main types are
Shell & Tube HEs
Air-cooled HEs
Plate HEs
Plate HEs
Air-cooled HEs
S/T HE
Plate HE
HORIZONTAL VESSELS:
Foundation Type & Shape: Reinforced spread foundations or pile foundations shall be
used.
The plane shape of foundation footings and pedestals shall be
generally rectangular.
A foundation shall have footings equivalent to the number of
saddles of each equipment and will be connected to each other
as necessary using a footing (grade) beam.
HORIZONTAL VESSELS:
The widths (a &b) of a
pedestals shall, in principle,
be greater than:
250 mm
125 mm from the center of
an equipment anchor bolt
25 mm from each side of a
equipment base plate.
HORIZONTAL VESSELS:
Where the height (hp) of the
pedestal is 1500 mm or
larger, corbels shall de
considered.
HORIZONTAL VESSELS:
Regarding Pile Arrangement, for the number and layout of
piles, one of the cases shown in figure shall be applied.
CASE 1
CASE 2
CASE 3
CASE 4
xZp
2L
3L
4L
5L
yZp
4F
4F
8F
8F
HORIZONTAL VESSELS:
Design Data:1.
2.
WEIGHT:
The following weights given in the loading data shall be used as equipment weight:
Empty weight
Wem
Operating weight
Wop
Test Weight
Wt
Tube bundle weight
Wb
Equipment Data
DIMENSIONS:
Sheet
HORIZONTAL VESSELS:
Loads Applied to the Pedestal:1.
Empty Load
: Pem = Wem (1/2+e/L)
Operation Load
: Pop = Wop (1/2+e/L)
Test Load : Pt = Wt (1/2+e/L)
HORIZONTAL VESSELS:
Loads Applied to the Pedestal:2.
Ex = k/2 Wop
If thermal resistance force i.e. Wop is less than Ex, then all
the Earthquake force equal to kWop shall be applied to fix
side only.
Where is the friction coefficient.
kWop
Ex
FE
kWop
Ex
SE
kWop
FE
SE
HORIZONTAL VESSELS:
Loads Applied to the Pedestal:b) TUBE BUNDLE PULLING FORCE (Fb)
Tube bundle pulling forces are loads occurring solely in the
case of heat exchangers. Under the empty weight,
maintenance of tube bundles is carried out.
Wb
Fb
SE
Wb
FE
SE
HORIZONTAL VESSELS:
Loads Applied to the Pedestal:c)
Th = Pop
Typical Coefficients of friction are as follows:
0.50
0.10
HORIZONTAL VESSELS:
Loads Applied to the Pedestal:3.
HORIZONTAL VESSELS:
Loads Applied to the Pedestal:4.
MOMENTS
Moment arm for moments
working on pedestal surfaces
due to horizontal forces
applied in axial and transverse
direction is h .
However, for bundle pulling
force, moment arm is the
hmax.
HORIZONTAL VESSELS:
Foundation Design:
Soil/Pile Bearing
Sliding Check
Overturning Check
VERTICAL VESSELS:
Vertical Vessels mainly includes:
Process Columns
Vertical Drums (3-Legged Vessels)
Reinforced Concrete foundations with a
spread footing or piling.
Mostly for Vertical Drums block type
foundations are preferred.
For Process Columns, configuration of
the pedestal and footing shall be as
follows:
dp or l 2.0 m
: Rectangular
dp or l > 2.0 m
: Octagonal
VERTICAL VESSELS:
Data Sheet
PACKAGE EQUIPMENTS:
Package Equipments are the one in which only governing load is the DEAD
LOAD. No significant vibrations are imparted.
Foundations for Package Equipment are referred as SKID FOUNDATIONS.
Skid Foundations are only checked for the Stability.
Weight Check, rebar volume check and thickness check is not required for package
equipments.
MACHINERY EQUIPMENTS:
General Overview
Foundation Type & Shape
Static Design Loads
Static Design
MACHINERY EQUIPMENTS:
General Overview:
Reciprocating Machinery
Machinery with reciprocating masses as major moving parts. This machinery
should be supported as close to grade elevation as possible directly on rigid block.
MACHINERY EQUIPMENTS:
General Overview:
Rotating Machinery
Machinery with rotating masses as major parts. This machinery may be supported
on a rigid block or on an elevated structure.
MACHINERY EQUIPMENTS:
Foundation Type & Shape:1.
Foundation Type
MACHINERY EQUIPMENTS:
Foundation Type & Shape:2.
Foundation Shape
MACHINERY EQUIPMENTS:
Static Design Loads: In addition to the Dead Load of Machine following loads
should be considered for static design: Vertical impact of 50% of the dead weight of the machine and base
plate.
A lateral force of 25% of the weight of each machine including its base
plate applied normal to its shaft at a point midway between its end
supports.
A longitudinal force of 25% of the weight of each machine and its base
plate applied along the shaft axis.
Lateral and longitudinal forces shall not be considered to act
concurrently.
Seismic Loads should also be considered in accordance with project
specifications.
MACHINERY EQUIPMENTS:
Static Design: Weight Check
For Reciprocating Machines:
Weight of Rigid Block should be 3 - 5 times the weight of Machine.
Weight of Pile Cap should be 2.5 4 times the weight of Machine.
For Rotating Machines:
Weight of Rigid Block should be 2 - 3 times the weight of Machine.
Weight of Pile Cap should be 1.5 2.5 times the weight of Machine.
Stability Check
Rigid block should be check against Soil Bearing, Sliding &
Overturning.
However, for spread footings 50% reduction in allowable soil pressure
should be considered.
MACHINERY EQUIPMENTS:
Static Design: Rebar Volume Check
The effects of shrinkage and thermal expansion shall be taken into
account to prevent cracking. The minimum quantity of reinforcement
in concrete shall be 30 kg/m3 for rigid blocks.
THANK YOU
FOR YOUR KIND
ATTENTION