Professional Documents
Culture Documents
9500 MPR Installation Test and Turn Up - Module 1 - Product - Ed07
9500 MPR Installation Test and Turn Up - Module 1 - Product - Ed07
9500 MPR Installation Test and Turn Up - Module 1 - Product - Ed07
MSS-O
Derived from MSS4/8 and with the same level of feature set,
it is a ½ U pizza box, 16E1/DS1 + 6 Gbit/s interfaces
HSK Sub-D15
4 Inputs Reset
2xRJ45 (PoE) 2xSFP 3 Ouputs button
MSS-4 Supports up to 12 unprotected links, or 1 protected link and 10 unprotected links, or 2 protected links and 8 unprotected links
Fan unit is optional and is needed in order to reach +65°C; MSS-4 without Fan Unit supports up to +45°C for all equipment configurations.
MSS-8 Supports up to 24 unprotected links, or 1 protected and 22 unprotected links, or 2 protected and 20 unprotected links, or 12 protected links.
Flash Card
2 4 8
1 3 5 6 7
5
1 2
2. 2x1000 SFP optical interface with speed up to 10 Gb/s: port #5 and port #6
• to be used as GigaEthernet interface (the optional SFP must be installed; SFP can be 10G or 1G)
3. 2x1000 SFP optical interface with speed up to 1 Gb/s: port #7 and port #8
• to be used to connect an MPT-HQAM
• to be used as Synch-In and Synch-Out ports. Install the relevant custom SFP
• to be used as GigaEthernet interface for Ethernet traffic
4. 1 x 10/100 Base-T LAN for 9500 MPR Craft Terminal or NMS
5. 2 LED indicators for test and status
•Termination or reconstruction of the E1 signal with the original PDH Timing meeting G823/824 Requirements.
•Encapsulation/Extraction of those PDH data flows into/from std Eth packets MEF8 Compliant
•Up to 6 boards on MSS-8 shelf
2
1
In case of EPS line protection two boards will be plugged inside the sub rack and an additional protection panel
will perform a ‘Y’ connection for both Tx and Rx PDH signals.
1 2
In case of EPS line protection two boards are plugged inside the sub rack.
Optional splitter Y-cables are provided for both Tx and Rx SDH signals.
1 2
4. EASv2 and EASv1 / Modem / MPT Access can co-exist in the same shelf, but NOT in the same row
6. EASv2 and EASv1 are air compatible : possible to have one station with EASv2 and the other station with EASv1
1 2 3
MPT 2
MPT 1
1. 2 x 10/100/1000 Base – T Port for electrical data to/from MPT and Power feed over Ethernet through CAT5 cable.
2. 2 x SFP Optical GE for optical data connectivity to/from MPT (SFP SX)
3. Double 50Ω QMA Connectors as an option for MPT Power feeding in case of optical connectivity
• When MPT is connected to CORE, power injector is needed to provide power to the MPT at optimized price
• When MPT is used in stand alone (MPR-e) and connected to 7705SAR, Power injector plug-in can be used inside
7705 chassis to power MPT
2xE1 SFP can be plugged in one of the two SFP ports of Core card, providing two G.
703 E1 interfaces (up to 4xE1 in case Core Card hosts 2 SFP).
Delivers Gigabit Ethernet traffic over a single STM-1/OC-3 link optical in a SFP cage
with LC connector
EoSDH SFP can be plugged in one of the two SFP ports of Core card (up to 2xSTM-1 in
case Core Card hosts 2 SFP).
The device converts E3 interface into packets for transmission via the SFP port of
the Core Board; a remote E3 SFP converts the packets back to TDM traffic.
1xE3 SFP cage with 1.0x2.3 connector can be plugged in one of the two SFP ports of
Core card (up to 2xE3 in case Core Card hosts 2 SFP.
EPS protection is available in case Core Card is protected: the secondary SFP is hosted by the stand-by Core,
and a Y cable is provided to connect the 2 SFP.
• EOW connector
• Service channel interface #1 (RS422 V11 DCE 64 kbit/s)
• Service channel interface #2 (RS422 V11 DCE 64 kbit/s)
• Housekeeping interface (6 inputs + 7 outputs).
(The polarity of each alarm is user configurable and a user defined label could be added per each alarm)
Only one auxiliary card per NE can be equipped, and in a fixed position:
it can be lodged in slot 8 (bottom right) of MSS-8 or in slot 4 (bottom right) of MSS-4.
2 3
• Powers up to 4 MPT
• integrated lightning arrestor and filter for each ODU
• Voltage range for DC In & DC Out interfaces : -38,4V to -57,6V
1
4 4
5 5 3
2 2
1. 2x Power In Connectors
2. 2x N Connectors
3. 1x RJ-45 Connector
4. 2x Ethernet (100/1000 Base-T),
5. 2x DC Power to XP
2 3 2 3
Interfaces
1000 BaseT with Power Feed over Ethernet (up to 100mt)
- No RPS function
- No XPIC function
- No optical connectivity
RPS module
XPIC Port
XPIC Port
Optical RPS Port
LEMO Connector
H polarization
f1 f2 f2 f4
f1 f3
V polarization