Professional Documents
Culture Documents
Agitation: Introduction To Principles and Practice
Agitation: Introduction To Principles and Practice
Agitation: Introduction To Principles and Practice
2
Agitation
-refers to the induced motion of a material in a
specified way, usually in a circulatory pattern
inside some sort of container.
3
Examples of Processes that uses
Agitation
• Blending of two miscible liquids
• Dissolving solids in liquids
• Dispersing a gas in a liquid as fine bubbles,
such as oxygen in a suspension of
microorganisms for waste-treatment
• Suspension of fine solid particle, such as
metallic pigments in paint
• Agitation of a fluid to eliminate temperature
gradients
4
Agitation Equipment
• Cylindrical vessel with a vertical axis
• Vessel bottom is rounded
• Liquid depth is approximately equal to the
diameter of the tank
• An impeller is mounted on an overhung shaft.
Shaft is driven by a motor
• The impeller creates a flow pattern in the
system, causing the liquid to circulate through
the vessel and return eventually to the
impeller
5
Impellers
• Divided into two classes:
– Axial-flow impellers
generate currents parallel with the axis of
impeller
– Radial-flow impellers
generate currents in a tangential or radial
direction.
• Three main types of impellers:
– Propellers
– Paddles
– Turbines
6
Propellers
• Axial flow high speed impeller, for liquids of
low viscosity
• Small impellers turn at full motor speed
• Pitch of propeller: a propeller with a pitch of
1.0 is said to have square pitch
• Rarely exceed 18” in diameter regardless of
the size of the vessel
• In a deep tank two or more propellers may
be mounted on the same shaft
7
Propellers
8
Paddles
• Flat paddle turning on a vertical shaft
• Two-bladed and four-bladed paddles are
common
• Sometimes the blades are pitched; more
often they are vertical
• Push the liquid radially and tangentially with
almost no vertical motion
• In deep tanks several paddles are mounted
one above the other on the same shaft
-contd..
9
Paddles
• In some designs blades conform to the
shape of the vessel so that they scrape the
surface or pass over with close clearance
– Eg. Anchor agitators
• Anchor agitators are useful for preventing
deposits on a heat transfer surface
• Industrial paddle agitators turn at speed
between 20 and 150 rpm
• Total length of impeller is 50-80% of the ID
of vessel
10
Paddles
Four bladed
Anchor type
11
Turbines
• Multi-bladed paddle agitators with short
blades, turning at high speeds
• Blades may be straight, or curved, pitched or
vertical
• Impellers may be open, semi-enclosed, or
shrouded
• Dia of impeller is smaller than with paddles,
ranging from 30 to 50% of vessel dia
• Effective over a wide range of viscosities
12
Turbines
Open straight-blade
turbine Open curved blade
turbine
13
Selection of Impellers
• In the direction of viscosity increase
Propeller Turbine Paddle Anchor
Helical ribbon Helical screw
18
Prevention of Swirling
20
Degree of Agitation
• Agitator tip-speed is
commonly used as a
measure of degree
of agitation Low 500-650 fpm
• Tip-speed = D n
• Expressed in Medium 650-800 fpm
feet/min (fpm)
High 800-1100 fpm
21
Std Speed of Impeller Gear ratio
speed, rpm
Impellers
284 5:1
• Motor speed: 190 7.5:1
1420-1450 rpm for 142 10:1
50Hz, AC
100 15:1
• Worm gear
71 20:1
reducers with
ratio: 5:1 to 60:1 57 25:1
48 30:1
37 40:1
30 50:1
25 60:1
22
Power consumption
• Power required to rotate a given
impeller depends on:
– important measurements of tank and
impeller
– viscosity and the density of the liquid
– speed of agitator
– acceleration of gravity g
• Empirical correlations of power with the
above variables by dimensional analysis
are available.
23
Power correlation
• Power P is a function of the variables:
• By dimensional analysis:
24
Dimensionless Groups
• Power number
• Reynolds number
• Froude number
25
Power Correlations
26
Calculation of power consumption
• From the definition of NP
27
Mixing
• Mixing refers to the random
distribution, into and through one
another, of two or more initially
separate phases
• A single homogenous material, such as
a tank full of cold water can be
agitated, but it can not be mixed until
some other material is added to it
28
Factors enhancing mixing
• Low interfacial tension that inhibits the
formation of interfaces
29
Uniformity of Mixing - Measuring
By Various kinds of tracer techniques:
• A dye is introduced and the time for attainment of
uniform color is noted
• A concentrated salt solution is added as tracer and
the measured electrical conductivity tells when the
composition is uniform
• The residence time distribution is measured by
monitoring the outlet concentration of an inert tracer.
The shape of response curve is compared with that
of a ideally mixed tank
30
Degree of Mixing - Quantification
• Standard Deviation:
where
xm (with an over-bar) is the mean fractional concentration
xi = the fractional concentration of the component in the i-th
sample
N = the number of samples taken
31
Mixing Index
where
32
How long to Mix
• Mixing index decrease with time according to
33
Scale-up of Agitator Design
• When a small unit is built before the larger or
production unit – pilot plant
• When a small unit is built after the production
unit - model
• Scale-up requires three types of similarity
between pilot-plot unit and full-scale unit:
– Geometric similarity
– Kinematic similarity
– Dynamic similarity
34
Geometric similarity
• Refers to linear dimensions
• Two vessels of different sizes are
geometrically similar if the ratios of the
corresponding dimensions on the two
scales are the same
• If photographs of two vessels are
completely super-impossible, they are
geometrically similar
35
Kinematic Similarity
• refers to motion
36
Dynamic Similarity
• concerns forces
38
39
40
41
Necessary conditions for Effective
Scale-up
• First the regime must be a relatively
pure one. Dynamic similarity should
depend chiefly upon a single
dimensionless group that represents the
ratio of applied to the opposing forces