Professional Documents
Culture Documents
BS241 BR 08 - 04 Commissioning
BS241 BR 08 - 04 Commissioning
Commissioning
FDMA System
GSM 900 / 1800
25 MHz 25 MHz
75 MHz 75 MHz
Guard band
C C
C C C 124 C C C 124'
1 2 3 374 1' 2' 3' 374'
200 kHz
C - Radio Frequency Channel (RFC)
1TS = 577 s
TDMA
1 TDMA frame =
8 TS = 4.615 ms frame
1
0
7
6
5
4
3 time
2
1
0
Extension Rack
Power à -48 V (-15% to 20%) Power Power -> 220 V (176 to 239 V)
using COSA
COBA / COSA DIP Switch COSA
TRX Conf.
Semirigid Wiring Semirigid Wiring
TRX Conf.
DCBCTRL
Selic Cable Selic Cable voltage test
battery capacity
slot ID
PCM Link Cable BPORT Setting battery manufacture
finish
1 2 3 4
Base Rack 0 off off off on
Extension Rack 1 on off off on
ON
Extension Rack 2 off on off on
Service Rack 3 on on off on
Service Rack 4 off off on on
Service Rack 5 on off on on ACT factory setting
Service Rack 6 off on on on
Service Rack 7 on on on on
Not Used
ENVA No Name
9 PLN Off
10 Door
11 Fire
12 Shelter in Service
13 Major Rectifier
14 Temp. for Rack (Low)
15 Temp. for Rack (High)
16 Room Temperature
17 Outdoor Unit AC
18 AVR Automatic Bypass
19 ATS Fail
20 Arrester Fail
21 Genset Run
22 Low Volt Battery
23 PLN On
24 Battery Fuse Trip
25 Rectifier Module Fail
26 Spare
ENVA:9 ENVA:10 ENVA:11 ENVA:12 ENVA:13 ENVA:14 ENVA:15 ENVA:16 ENVA:17 ENVA:18 27 Spare
CAN OUT - 48
CAN OUT CAN IN CAN OUT CAN IN
Serial IF
CAN TEST LPA CAN TEST LPA CAN TEST LPA
Ext. 2 CU 4 ... 7
Ext. 2 CU 0 ... 3
_ +
Voltage test
Oerlikon :
Bit 0 -> on
ON
Battery Batt Bit 1 Bit 1 -> not used
Manufacture type Bit 0
Sonnenschein :
Bit 0 -> off
Bit 1 -> not used
ON
640 Ah
Batt. 0 320 Ah
capacity 160 Ah
80 Ah
Batt. 1 40 Ah
20 Ah
capacity
10 Ah
5 Ah
ACDCP 0 :
Bit 0 -> on
ON
ACDCP 1 :
Bit 0 -> off
Bit 1 -> on
GND
GND
GND
4
A B A B A B A B 2
3
1
TX RX TX RX
5 6 7 8 9 10 11 12
GND
GND
GND
GND
A B A B A B A B
TX RX TX RX
TEI = ?
Timeslot = ? Base Rack Service Rack
SALUNAME = ?
BTSM = ? Set Rack -> 0 Create Rack à 3
no
Create ACDCP
Create Battery
yes
Create BPORT
Create LAPDLE
Turn on BTS
Check phase Set BTSM
phase 2
Set BTSEP
phase 1
Format BTSE Flash Create FANP Create FANP
BSC
Link Configuration :
BTS A and BTS C -> Star
PCM 1
PCM 2
PCM 3
PCM 4
PCM 1
PCM 2
PCM 3
PCM 4
BPORT BPORT
0 1 2 3 0 1 2 3
BTS B BTS C
Jika dalam Base Rack terdapat FCU maka COBA perlu di set TRUE
TRUE = support of FCU enable
FALSE = support of FCU disable
RACK0/Base Rack
1
Inventory data on Rack
Available ?
no yes
2 Upload REMINV
Manual list
3 Export NOB -> save file
Create Nob RIUs file for DL? -> No
Upload REMINV
BS-240
BS-240 II