Professional Documents
Culture Documents
1.MW Product&EMS Training
1.MW Product&EMS Training
1.MW Product&EMS Training
Part 2 Installation&Dedugging
Part 3 Configuration
Eband
NR8250&NR8120D
N
R
8
2
5
0
RCU Radio control unit RPU Radio power unit
RTU Radio transmission unit RFAB Fan
RMU Radio modulation unit PM Power management
NR8250&NR8120D
N
R
8
2
5
0 RTUB 8E1&STM1&STM1/4 RTUC 32E1
RTUNE 4GE OR 2GE 2optical RTUIO 10GE
RMUF 1IF(XPIC cable) RMUN 2IF(Inner XPIC)
3 1+1 HSB/SD group slot3&4 slot5&6 slot7&8
PM RCU RTU/RMU/RSU
RTUHO/E Native TDM+Ethernet Traffic Unit (Opt./Elec.) 2-8
RCU/RTU/RSU RTU/RMU/RSU RFA
PM RTU/RMU/RSU RTU/RMU/RSU Traffic Unit RTUNO/E Ethernet Traffic Unit (Opt./Elec.) 2-8
RPU RTU/RMU/RSU RTU/RMU/RSU
RTUIO 10GbE Traffic Unit (Opt.) 2-4
RPEA PoE Traffic Unit (Elec.) 3-8
Auxiliary
RSUA Auxiliary Service Traffic Unit 2-8
Service Unit
LED indicator GbE2 interface LMT interface USB interface RST button
LED indicator GbE/1NMS interface GbE3 interface CLK/MON interface M/S button LED indicator
Clock & Monitor multiplex interface, support clock input or output, supports 2MHz/2Mbps BITS clock and 1PPS+ToD
CLK /MON HDMI
clock; RS485 monitor port, connect with the RS485 port of cabinet
USB USB U disk for fast configuration or USB Wi-Fi access for local management
RMUF Interface
LED indicator Power switch IF interface RST button
RMUN Interface
RTUA/RTUC Interface—Native E1
RTUA
RTUC
RTUHO
RTUHE
LED indicator
RTUHO
RTUHE
NR8250&NR8120D
N
R
8
1
2
0
RTEA 16E1
4GE+1GE+1/10GE+16E1+2IF
1+1/1+0/2+0
NR8250&NR8120D
1+0/1+1 for end site
2<=IF<=6
IF=10
RF in/out
RF in/out
(waveguide type )
(waveguide type )
RSSI IF in/out
RSSI IF in/out
Frequency Bands: 6, 7, 8, 10, 11, 13, 15, 18, 23, 26, 28, 32, 38, Frequency Bands: HRU: 6, 7, 8, 11 GHz
42GHz Modulation scheme:
Modulation scheme: HRU V1.3: QPSK~1024 QAM @ BW 7/14/28/40/56 MHz.
SRU V1.3: QPSK~1024QAM @ BW 7/14/28/40/56 MHz HRU V2.0: QPSK~2048 QAM @ BW 7/14/28/40/56 MHz.
SRU V1.4: QPSK~2048 QAM @ BW 7/14/28/40/56 MHz. SRU/HRU support remote and direct mounting methods
Eband
Installation&Debugging
Part
2 General installation
1+0/1+1/2+0/4+0
Link debugging
General installation
1+0/1+1/2+0/4+0
1+1 Because the screw position of ZTE unblanced hybrid is different from reused Andrew
antenna,so we need use integrated adaptor between hybrid and antenna
1+0/1+1/2+0/4+0
1+1 The default polarization of hybrid is vertical,when the design is horizontal,we need
change it by guide pin
change(check) the polarization of Antenna .If the PQ polarization is H,change the guide
pin on integrated adaptor
Remove these 4
screws,and turn guide
pin 90 degree
1+0/1+1/2+0/4+0
2+0 We use OMT antenna,dual polarization,the hybrid can support V&H without waveguide
If connected to RMUN(2IF),please use 5-1 for H and 5-2 for V,it’s better for maintenance
1+0/1+1/2+0/4+0
1+0 We also use OMT antenna for 1+0, Another port on OMT should be blocked by short kit
1+0/1+1/2+0/4+0
4+0
5-1 : H1 5-2 : V1
6-1 : H2 6-2 : V2
© ZTE All rights reserved
29
Internal use only▲
1+0/1+1/2+0/4+0
4+0
Waveguide for H&V Loosen the 4 screws and then turn around debugging
Tray installation(4+0 xpic)
ODU combiner and Tray installation(4+0 xpic)
Link debugging
One direction have one PLA
Link debugging
Power off 5-2,6-1,6-2 on both site,working as 1+0
adjust the antenna until the RSL meet the reference value
Power on 5-2 on both site,working as a 2+0
Adjust the fixed feeder slowly,let XPI value of both site between 30 to 35
Power on 6-1/6-2 to check the XPI value and fine adjustment let 8value between 30-35
Part Configuration
3 System Configuration
Radio Configuration
VLAN&E1 Configuration
System configuration
Login IDU
System configuration
Login IDU
System configuration
Basic parameter1
System configuration
Base parameter2
10.20.206.8
System configuration
Basic parameter3
System configuration
SNMP
Radio link
Shelf for adding new card
Radio link
Basic Configuration of radio link
Radio link
Basic Configuration of radio link
0 QPSK
2 16QAM
3 32QAM
4 64QAM
5 128QAM
6 256QAM
7 512QAM
Radio link
Basic Configuration of radio link
Radio link
Basic Configuration of radio link
VLAN&E1 Configuration
E1 Configuration
VLAN&E1 Configuration
Port Configuration
VLAN&E1 Configuration
Vlan Configuration
PLA&XPIC Configuration
PLA&XPIC Configuration
PLA&XPIC Configuration
PLA&XPIC Configuration
Radio loop
Frequency sweeping
E1 Interface&MU loop
MU E1 loop
MU loopback is used for check the E1 modem cross, sometimes we cannot confirm H&V
connect to which IF port(maybe one site 5-1 is H but remote site 5-2 is H)
© ZTE All rights reserved
56
Internal use only▲
E1 Interface&MU loop
TDM port loop
Radio loop
Radio loop
Frequency sweeping