Professional Documents
Culture Documents
Print On Cardstock: Launch Umbilical Tower
Print On Cardstock: Launch Umbilical Tower
Print On Cardstock: Launch Umbilical Tower
PRINT ON CARDSTOCK
Score/Mountain
Fold line
Score/Mountain
Score/Mountain
Fold glue tabs &
Fold glue tabs &
lower tower cap.
upper tower cap.
Score/Mountain
Fold line
Glue Tab
Mountain fold
all triangular
glue tabs on
both ends
SEATTLE
COLBY CRANE
Front
© 2005 Drawn by Michael Burke
Rear Tower Base
This cardmodel is only for personal
and not commercial use. Score/Mountain
COLBY CRANE
SEATTLE
Fold line
Glue Tabs
Crane Keel
Sandwich and glue both halves around cardstock Glue Tab
Top
Bottom
Glue
Inner Sleeve
Print on Cardstock Tab
Centering Circle
Glue Tab
Score/Mountain
Fold Lines Glue Tab
10 TON 25 TON
Score and Mountain
Fold along dark gray
Trim this piece line at base of tower
to fit Score/Mountain
Fold Lines
25 TON 10 TON
Glue Tab
Score and Mountain
Fold along dark gray
Glue Tab line at base of tower
SIDE 3 SIDE 3
PRINT ON CARDSTOCK
1 1 Circles on underside of platform are for locating holes for
tower pedestals. After platform is complete, carefully drill
holes with tip of X-Acto knife. Insert pedestal tubes all the
way to the underside of the top of the platform deck.
SIDE 4
SIDE 2
1
1
Hold Down
Carefully Cut Arm Supports
Carefully Cut
out White out White
Portion Portion
Hold-Down Arm Supports
These are wedge-shaped
pieces that are glued to
the underside of the
square protrusions in the
top opening of the thrust
chamber and to the face of
SIDE 4
SIDE 2
Glue
Tabs See Crane Parts Page
for Hold Down Arms and
Launcher Pedestals
Glue Tab
Glue Tab
Glue Tab
When CM Access
Arm is complete,
from the top, it
CM Access Arm should be shaped Score/Fold Score/Fold
like and mounted lines lines
Glue Tab
Score/Fold to side of tower,
Lines like this. Damper Arm
S-IC Intertank
Other arms are Glue Tab
Score/Fold lines Glue
Glue Tab mounted to front S-IC Forward
Tab
of tower, like this.
(See drawing for
placement.) Score/Fold lines
Glue Tab
Carefully
Carefully cut this Glue Tab Glue Tab
cut this white
white notch out
section out
Score/Fold
line When completed, Score/Fold Score/Fold
Glue Tab the Damper arm lines lines
assembly goes
together like this. © 2005 Drawn by Michael Burke
Score/Fold This cardmodel is only for personal
Lines and not commercial use.
Launcher Base Pedestals
PRINT TO BOND BAPER Roll into double layered tubes – Glue edge to centerline
Lightning Rod
Inner Sleeve
Machinery House
Centering Circle Mountain Fold/Score lines
Glue Tab
to fit
COLBY CRANE
Score/Mountain
Front
Fold Lines
Rear
25 TON 10 TON
COLBY CRANE
Score/Mountain
SEATTLE
Fold line
© 2005 Drawn by Michael Burke
This cardmodel is only for personal
Glue Tab and not commercial use. Glue Tab
S-IVB
Service
Module
This wedge
is a glue
Command tab
Engine Fairings
Module
S-IVB Centering Rings
Glue Rings to
Cardstock and
glue one in front Launch Escape
Roll Into double-layered tubes and one in back Tower
of S-IVB Roll Into Cylinder
S-IC, Interstage, & S-II PRINT TO BOND BAPER
Interstage
U
N
U
N
U
N
U
N
© 2005 Drawn by Michael Burke
I
T
I
T
I
T
I
T
This cardmodel is only for personal
E
D
E
D
E
D
E
D
and not commercial use.
S S S S
T T T T
A A A A
T T T T Centering Rings
E E E E
S S S S Glue one in front and back of
S-1C/S-II Tube
Glue to Cardstock
U U U U
SM/LM Adapter
S S S S
A A A A F-1 Engines