Professional Documents
Culture Documents
GT-N5100 Training Manual HW
GT-N5100 Training Manual HW
March, 2013
1. All functionality, features, specifications and other product
information provided in this document including, but not limited
to, the benefits, design, pricing, components, performance,
availability, and capabilities of the product are subject to change
without notice or obligation. Samsung reserves the right to make changes to this document
and the product described herein, at anytime, without obligation on Samsung to provide notification of
such change.
2. Service Guide
• RF calibration
• IMEI writing
• Block Diagram
3. Repair Guide
• Assembly & Disassembly
• Electronic Components
• SMD parts
• Trouble Shooting
4. Q&A
Item spec.
AP 1.6GHz Quad Core(Exynos 4412)
OS Android JB
CP XMM6262(IMC), HSPA+ 21.1Mbps, HSUPA 5.76Mbps
Supported RF Bands GSM Quad(850, 900, 1800, 1900), UMTS Quad(850, 900, 1800, 1900)
Internal Memory 16GB NAND + 2GB RAM
External Memory MicroSD (up to 64GB)
Display 8” TFT (1280 x 800)
Camera 5MP CMOS + 1.3MP CMOS
Sensor Accelerometer, Magnetic, Proximity, Light, Grip
Connectivity BT 4.0, Wi-Fi a/b/g/n
GPS A-GPS + GLONASS
Battery 4600mA
Click the
Model Information
Check the
System Config items
Click the
OK button
Check and
select correct file
Check the IMEI
and select correct file Check the IMEI
Click the
Hardware
Config
Check the IMEI Write
and IMEI Check
Check the
System Config items
SPK(L)
Module
GH59-12907A
U1001 1204-003387
IrDA IC OSC200 2805-001098
Oscillator – 26MHz
UME600 1107-002190
MoviNAND
U201 1205-004649
GPS IC (inside of shield-can)
UCD400 1205-004510
Audio CODEC
HDC900 3708-002222
Connector (5M Camera)
U702 1203-006346
Reset IC
U701 1203-007657
PMIC
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
Less than 3.4V Battery
2 Check the battery voltage.
More than 3.4V Go to the next step
Abnormal(open, tear, etc) Power-key FPCB
3 Check the power-key FPCB.
Normal Go to the next step
Power on the device and check the power-on Abnormal Front Ass’y
4
sound or motor vibration. Normal Go to the next step
C755>1.35V, C754>2.0V,
Check the voltage of the following chips C727>1.0V, C736>1,95V Go to the next step
5 AP_PS_HOLD(TP) > 1.8V
(C755, C754, C727, C736, AP_PS_HOLD(TP))
If not the correct value PMIC (U701)
32KHz Main chip (UCP600)
6 Check the frequency of OSC700(C705)
If not the correct value TCXO (OSC700)
Vbatt
Step5
Step5
Step6
Step6
C705
OSC700
AP_PS_HOLD(TP)
U701
C754
C755
C727
C736
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
C763 = 5V Go to the next step
2 Check the voltage of V_BUS(C763). Connection status of
If not the correct value
TA or USB.
Abnormal Charging IC(U705)
3 Check the charging operating of battery.
Normal -
Step2,
Step2, 33
U705
Charging IC
C763
Step4
Step4 OSC100
DCXO – 26MHz
U100
Transceiver
F101
SAW Duplexer
F100 ASM
PAM100
PAM
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
SIM socket or
Broken, dust, corrosion
2 Check the SIM socket & Connector(HDC300) Connector
Normal Go to the next step
Check the voltage of detection pin R330 = 1.8V Go to the next step
(R330)
3
Notice. It should be measured when the If not the correct value SIM Card
phone is started
Check the voltage of SIM R331 = 3V PBA
(R331)
4
Notice. It should be measured when the If not the correct value CP(UCP300)
phone started
Step2,
Step2, 3,
3, 44
R330 R331
HDC300
SIM socket connector
SIM socket
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
Dust Clean the hole
2 Check the microphone hole
Normal Go to the next step
Wrong insert Re-insert
3 Check the microphone rubber
Normal Go to the next step
Abnormal Speaker(R)-MIC module
4 Check the MIC FPCB status
Normal Go to the next step
Check the voltage of C413 2.8V Go to the next step
5
Notice. It should be measured when the If not the correct value MIC LDO(U401)
microphone path is activated on
Check the signal of C418, C419 Same signal compared with a
Microphone
good PBA
6
Notice. It should be measured when the
microphone path is activated on If not the correct value AUDIO CODEC(UCD400)
Step6
Step6 Step5
Step5
C418
UCD400 U401
Audio CODEC
C419
C413
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
Solved Setting error
2 Make a factory reset (*2767*3855#)
Not solved Go to the next step
Check the speaker connector (HDC400(L) in Broken, dust, corrosion Speaker connector
3
Main PCB, HDC101(R) in Sub PCB) Normal Go to the next step
Solved speaker
4 Replace the speaker module
Not solved Go to the next step
Check the signals on Same signal compared with a
Speaker
L406, L407 of Left Speaker in main PCB, good PBA
C105, C106 of Right Speaker in Sub PCB.
5
Notice. It should be measured when the If not the correct value Audio Codec (UCD400)
speaker path is activated on
Step3
Step3
Check the
SPK connector
Check the
SPK connector
Left Speaker
Right Speaker
+ Main MIC
Step5
Step5
C105
C106 L406
L407
Ste
Check point Result value Defect point
p
Step2,
Step2, 3,
3, 44
ANT202, ANT203
Step2
Step2
U203
BT/WIFI IC
BT/WIFI Antenna C251
OSC201
C250 C233
Ste
Check point Result value Defect point
p
Step3,
Step3, 44
Step2
Step2
C209 L200
C211
ANT202, ANT203 U200
U201
GPS IC OSC200
BT/WIFI Antenna
C200 C201
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
Broken, dust, corrosion LCD connector
2 Check the LCD connector (HDC800) Insert status (HDC800)
Normal Go to the next step
Check the signal or voltage of C804 and C806 If not the correct value LED Backlight IC(U802)
3 Notice. It should be measured when the display is Normal(C804 = high(18V),
activated on Go to the next step
C806 = V_BATT)
Check the voltage of C800 and C801 If not the correct value Buck boost Reg.(U800)
4 Notice. It should be measured when the display is Normal(C800 = V_BATT,
activated on Go to the next step
C801 = 3.3V)
Solved LCD
5 Replace the LCD
Not solved Main Chip or PBA
Step2,
Step2, 3,
3, 44
U800
C801
C800
C806
Step2
Step2
HDC800
LCD Connector
U802
C804
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
TSP connector
Broken, dust, corrosion
2 Check the TSP connector (SLC900) (SLC900)
Normal Go to the next step
Check the voltage of C913 If not the correct value TSP LDO(U902)
3 Notice. It should be measured when the
display is activated on C913 = 1.8V Go to the next step
Touch Sensor
Check the voltage of C902, C903 If not the correct value
IC(U904)
4 Notice. It should be measured when the
display is activated on C902 = 3.3V
Go to the next step
C903 = 1.8V
ZD903, ZD904,
Check the Signal of following chips If not the correct value ZD905, R908, R682,
(ZD903, ZD904, ZD905, R908, R682, R683) R683
5
Notice. It should be measured when the
display is activated on Same signal compared with a
Go to the next step
good PBA
Solved TSP
6 Replace the TSP
Not solved Main chip or PBA
Step2,
Step2, 3,
3, 4,
4, 55
U904
C903
C902 Touch Sensor IC
C913
R682
U902 ZD903
R683 ZD904
ZD905
R908
Step2
Step2
SLC900
TSP Connector
Check the Signal of R1041 If not the correct value R1041, U1007, U1008
6 Notice. It should be measured when the Same signal compared with a
display is activated on Go to the next step
good PBA
Solved Front Ass’y
7 Replace the Front Ass’y
Not solved Main chip or PBA
© Samsung Electronics Co., LTD | Confidential 41
S-Pen Problem
Step2
Step2
Step2,
Step2, 3,
3, 4,
4, 5,
5, 66
U1008
SLC1000 S-Pen IC
S-Pen Connector
R1042
C1045
C1052 C1046
R1041
C1036 C1037 OSC1001
C1035
U1005 R1031
R1032
U1007
U1006
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
5M CAM connector
Broken, dust, corrosion
2 Check the 5M CAM connector (HDC900) (HDC900)
Normal Go to the next step
Solved 5M CAM
7 Replace the 5M CAM
© Samsung Electronics Co., LTD | Confidential Not solved Main chip or PBA 43
5M CAM Problem
Step5
Step5
Step2,
Step2, 3,
3, 4,
4, 5,
5, 66
R678
R679
C920 F901
F900
C917
R906
C921
Step7
Step7
5M CAM Module
C922
TP_CAM_I900
TP_CAM_I901
HDC900
5M CAM connector
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
5M CAM connector
Broken, dust, corrosion
2 Check the 1.3M CAM connector (HDC901) (HDC901)
Normal Go to the next step
Check the voltage of following chips If not the correct value C925, C926, C927
(C925, C926, C927)
3 C925 = 1.8V, C926 = 2.8V,
Notice. It should be measured when the Go to the next step
1.3M CAM is activated on C927 = 1.8V
R907 = 24Mhz
Check the clock of R907 (Same signal compared with a Go to the next step
4 Notice. It should be measured when the good PBA)
1.3M CAM is activated on
If not the correct value Main chip
Check the Signal of following Test Point Same signal compared with a
Go to the next step
(TP CAM I900, TP CAM I901) good PBA
5
Notice. It should be measured when the
1.3M CAM is activated on If not the correct value R678, R679
R907
Step2,
Step2, 3,
3, 66
HDC901
1.3M CAM connector
Step5
Step5
F902 C925
C927 C926
TP_CAM_I900
TP_CAM_I901
Step5
Step5
Step7
Step7
1.3M CAM Module
R678
R679
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
C763 = 5V Go to the next step
2 Check the voltage of V_BUS(C763)
If not the correct value Charging IC(U705)
C506 = 5V Go to the next step
3 Check the voltage of V_BUS_IN(C506) Charge protection
If not the correct value
(U504)
Solved Sub PCB
4 Replace the Sub PCB
Not solved Main chip or PBA
U705
C763
Step4
Step4
Step3
Step3
Sub PCB
C506
U504
Ste
Check point Result value Defect point
p
1 Confirm the defect symptom - -
L1000 = 1.2V, C1006 = 3.3V,
Go to the next step
Check the voltage of following chips L1001 = 1.2V, C1010 = 1.8V
2
(L1000, C1006, L1001, C1010) MHL LDO
If not the correct value
(U1003, U1004)
Solved MHL IC(C1013)
4 Replace the C1013
Not solved Main chip or PBA
Step2,
Step2, 33
C1006 U1004
L1001
U1003
C1010 L1000
C1013
MHL IC