Professional Documents
Culture Documents
RAN19.0 Crystal Voice Coverage Improvement by Rate Adaption: UMTS Solution Design Department
RAN19.0 Crystal Voice Coverage Improvement by Rate Adaption: UMTS Solution Design Department
RAN19.0
Crystal Voice Coverage
Improvement by Rate Adaption
www.huawei.com
To avoid muting risks, the RNC checks for rate inconsistency between the
Iu interface and the Uu interface and, if any, transcodes data from the CN
to the bit rate supported by the Uu interface. The transcoding function
depends on the DEUa board.
downlink coverage.
Note: Low-quality voice services refer to services with a mean opinion score (MOS)
being 2 or below, or services with enhanced voice quality indicator (EVQI) being poor or
bad.
This feature may decrease the bit rate of voice services and also the percentage
of high MOSs.
Other NEs
None
License
Feature ID Feature Name License Control Item License Control
Name Item ID NE Sales Unit
Crystal Voice
Crystal Voice Coverage
WRFD- Coverage RNC per Erlang
Improvement by Rate LQW1CVCIRARES
190208 Improvement by Rate
Adaption(per Erl)
Adaption
One week before the feature activation, perform the following operations to enable intra-frequency measurement and
EVQI measurement:
1. Run the SET UMRSWITCH command with MR Switch set to ON.
2. Run the SET UMRCTRL command with MR Intra-freq Measurement period set to D2 and
MR_PRD_INTRA_FREQ_MEAS_SWITCH_1 selected under MR Report Configure Switch.
3. Run the SET UMRCTRL command with MR Trace Traffic Type set to TRAFFIC_AMR,
MR_DL_BLER_MEAS_SWITCH_7 selected under MR Report Configure Switch, and DL Bler Period set
to D6.
Range 5 = [5, 10) (This range maps onto the measured RSCP range [-
110 dBm, -105 dBm) specified in 3GPP TS 25.133.)
Range 6 = [0, 5) (This range maps onto the measured RSCP range [-
115 dBm, -110 dBm) specified in 3GPP TS 25.133.)
Counter Description
VS.EVQI.AMRWB.DL.TotalValue(UMTS BSC6900,UMTS Total Downlink EVQI of AMR-WB Services
BSC6910)
VS.EVQI.AMRWB.DL.Excellent.Num(UMTS Number of Times the Downlink EVQI of AMR-WB Services Is
BSC6900,UMTS BSC6910) EXCELLENT
VS.EVQI.AMRWB.DL.Good.Num(UMTS Number of Times the Downlink EVQI of AMR-WB Services Is
BSC6900,UMTS BSC6910) GOOD
VS.EVQI.AMRWB.DL.Accept.Num(UMTS Number of Times the Downlink EVQI of AMR-WB Services Is
BSC6900,UMTS BSC6910) ACCEPT
VS.EVQI.AMRWB.DL.Poor.Num(UMTS BSC6900,UMTS Number of Times the Downlink EVQI of AMR-WB Services Is
BSC6910) POOR
VS.EVQI.AMRWB.DL.Bad.Num(UMTS BSC6900,UMTS Number of Times the Downlink EVQI of AMR-WB Services Is
BSC6910) BAD
VS.EVQI.AMRNB.DL.TotalValue(UMTS BSC6900,UMTS Total Downlink EVQI of AMR-NB Services
BSC6910)
VS.EVQI.AMRNB.DL.Excellent.Num(UMTS Number of Times the Downlink EVQI of AMR-NB Services Is
BSC6900,UMTS BSC6910) EXCELLENT
VS.EVQI.AMRNB.DL.Good.Num(UMTS BSC6900,UMTS Number of Times the Downlink EVQI of AMR-NB Services Is
BSC6910) GOOD
VS.EVQI.AMRNB.DL.Accept.Num(UMTS Number of Times the Downlink EVQI of AMR-NB Services Is
BSC6900,UMTS BSC6910) ACCEPT
VS.EVQI.AMRNB.DL.Poor.Num(UMTS BSC6900,UMTS Number of Times the Downlink EVQI of AMR-NB Services Is
BSC6910) POOR
VS.EVQI.AMRNB.DL.Bad.Num(UMTS BSC6900,UMTS Number of Times the Downlink EVQI of AMR-NB Services Is
BSC6910) BAD
Note: The value of CrystalAdptEcN0Thld depends on the value of RlMaxDlPwr. For 12.2 kbit/s or 12.65 kbit/s AMR-NB
UEs, CrystalAdptEcN0Thld takes the default value -14 dB if RlMaxDlPwr is 0 dB; for 23.85 kbit/s AMR-WB UEs,
CrystalAdptEcN0Thld takes the default value -14 dB if RlMaxDlPwr is 3 dB. Reduce the value of
CrystalAdptEcN0Thld accordingly (for example, to -17 dB) if the actual value of RlMaxDlPwr is higher than the
preceding value (for example, 3 dB for AMR-NB UEs).
l Run the ADD UCELLAMRCWB or MOD UCELLAMRCWB command with Crystal Voice AMR Adjust Switch set to
ON.
Note: This feature can be activated in only certain cells under an RNC. Due to UE
movement and handovers, this feature can be effective for certain UEs in cells
where this feature is not activated. To provide stable KPIs and avoid
reconfigurations for such UEs, this feature works until they move to strong
coverage areas.
None
VS.DL.AMR.BLER.RSCP.6(UMTS BSC6900,UMTS BSC6910) Range 4 = [10, 15) (This range maps onto the measured RSCP range [-105 dBm, -
100 dBm) specified in 3GPP TS 25.133.)
Range 5 = [5, 10) (This range maps onto the measured RSCP range [-110 dBm, -105
dBm) specified in 3GPP TS 25.133.)
Range 6 = [0, 5) (This range maps onto the measured RSCP range [-115 dBm, -110
dBm) specified in 3GPP TS 25.133.)
Counter Description
VS.DL.AMR.CrystalAdapt.BLER.RSCP.2(UMTS These counters measure the average downlink BLER of the traffic channel for AMR-NB
BSC6900,UMTS BSC6910) and AMR-WB voice UEs enabled with Crystal Voice Coverage Improvement by Rate
VS.DL.AMR.CrystalAdapt.BLER.RSCP.3(UMTS Adaption on the DCH in each RSCP range in the best cell.
BSC6900,UMTS BSC6910)
VS.DL.AMR.CrystalAdapt.BLER.RSCP.4(UMTS Range 2 = [20, 25) (This range maps onto the measured RSCP range [-95 dBm, -90 dBm)
BSC6900,UMTS BSC6910) specified in 3GPP TS 25.133.)
VS.DL.AMR.CrystalAdapt.BLER.RSCP.5(UMTS Range 3 = [15, 20) (This range maps onto the measured RSCP range [-100 dBm, -95
BSC6900,UMTS BSC6910) dBm) specified in 3GPP TS 25.133.)
VS.DL.AMR.CrystalAdapt.BLER.RSCP.6(UMTS
BSC6900,UMTS BSC6910) Range 4 = [10, 15) (This range maps onto the measured RSCP range [-105 dBm, -100
dBm) specified in 3GPP TS 25.133.)
Range 5 = [5, 10) (This range maps onto the measured RSCP range [-110 dBm, -105
dBm) specified in 3GPP TS 25.133.)
Range 6 = [0, 5) (This range maps onto the measured RSCP range [-115 dBm, -110 dBm)
specified in 3GPP TS 25.133.)
Counter Description
VS.EVQI.AMRWB.DL.TotalValue(UMTS Total Downlink EVQI of AMR-WB Services
BSC6900,UMTS BSC6910)
VS.EVQI.AMRWB.DL.Excellent.Num(UMTS Number of Times the Downlink EVQI of AMR-WB Services Is
BSC6900,UMTS BSC6910) EXCELLENT
VS.EVQI.AMRWB.DL.Good.Num(UMTS Number of Times the Downlink EVQI of AMR-WB Services Is GOOD
BSC6900,UMTS BSC6910)
VS.EVQI.AMRWB.DL.Accept.Num(UMTS Number of Times the Downlink EVQI of AMR-WB Services Is ACCEPT
BSC6900,UMTS BSC6910)
VS.EVQI.AMRWB.DL.Poor.Num(UMTS Number of Times the Downlink EVQI of AMR-WB Services Is POOR
BSC6900,UMTS BSC6910)
VS.EVQI.AMRWB.DL.Bad.Num(UMTS Number of Times the Downlink EVQI of AMR-WB Services Is BAD
BSC6900,UMTS BSC6910)
VS.EVQI.AMRNB.DL.TotalValue(UMTS Total Downlink EVQI of AMR-NB Services
BSC6900,UMTS BSC6910)
VS.EVQI.AMRNB.DL.Excellent.Num(UMTS Number of Times the Downlink EVQI of AMR-NB Services Is EXCELLENT
BSC6900,UMTS BSC6910)
VS.EVQI.AMRNB.DL.Good.Num(UMTS Number of Times the Downlink EVQI of AMR-NB Services Is GOOD
BSC6900,UMTS BSC6910)
VS.EVQI.AMRNB.DL.Accept.Num(UMTS Number of Times the Downlink EVQI of AMR-NB Services Is ACCEPT
BSC6900,UMTS BSC6910)
VS.EVQI.AMRNB.DL.Poor.Num(UMTS Number of Times the Downlink EVQI of AMR-NB Services Is POOR
BSC6900,UMTS BSC6910)
VS.EVQI.AMRNB.DL.Bad.Num(UMTS Number of Times the Downlink EVQI of AMR-NB Services Is BAD
BSC6900,UMTS BSC6910)
Note: If many 23.85 kbit/s UEs are assigned the 6.6 kbit/s rate, you can set
QoSAMRCWBMinMode to a value higher than WBAMR_BITRATE_6.60K to avoid impacting
the MOS significantly.