Professional Documents
Culture Documents
Mahindra Windchims Bengaluru
Mahindra Windchims Bengaluru
ah
ind
r
Be a W
ng in
alu dc
ru him
s
Project View
Present Status
Phase-1 Phase-2
Status of MLDL
Work order Work done
Description Remarks
Area Area
Phase 1
Toilet (MYK Saniflex) 21000 sqm 10500 sqm
Complete
Podium (MYK Coat WPU 1K) 10000 sqm 2500 sqm
Tanks (MYK Aquafin UM) 2500 sqm 800 sqm
To
ile
Pr ts W
oo a
fin ter
g
Toilet Waterproofing
MYK Unigrungd-GE
MYK Saniflex
Protective Plaster
ASO Joint tape
Protective screed to
slope
Wall Final finish
Slab
Drain Spout
About Product
MYK Saniflex is synthetic rubber based single component elastic
waterproofing membrane,which is suitable for wet areas water
proofing.
Due to liquid form it is more easy to apply on substrate.
Seamless waterproof membrane system.
Fast curing allows tiling on same day.
It has elongation properties up to 115 %.
This membrane has excellent crack bridging up to 800 microns.
It can be used at high temperature up to 42 ° C.
It has high tensile strength 2.15 Mpa @ 20 ° C.
Limitations
It requires a dry substrate while application.
Concrete substrate should be at least 5 days old at the time of
application.
Second coat to be done when first is completely dry.
Proper protection to be taken to protect the membrane from
mechanical damages.
Ph S
ot ite
og
rap
hs
Surface Preparation Treatment of penetration point
Application of MYK Unigrund- Dry condition of MYK Unigrund-
GE GE
ASO Joint tape
1st Coat application of MYK 2nd Coat application of MYK
Saniflex Saniflex
Water pond for quality check Barrication
Protective Plaster Protective Screed
Most Important Points need to be remembered
Podium Slab
About Product
MYK Coat WPU-1K is a single component ,polyurethane
waterproofing membrane.
Due to liquid form it is more easy to apply on substrate.
Seamless waterproof membrane system.
High bonding strength over recommended primer (more then 1.5
Mpa).
It has elongation properties up to 550%.
This membrane has excellent crack bridging up to 1mm.
Excellent chemical resistivity.
It has high tensile strength 1.4 Mpa.
Limitations
It requires a dry substrate while application.
Concrete substrate should be at least 28 days old at the time of
application.
Application should be avoid when ambient temperature is below 12° C.
No dilution is required.
Mixed primer should be used with in 30 minutes.
Second coat to be done when first is completely dry.
Proper protection to be taken to protect the membrane from
mechanical damages.
As this is a moisture cured material, it forms a hard film over the liquid
material if it is exposed very long in atmosphere.
Ph S
ot ite
og
rap
hs
Surface Preparation
Treatment of
Initial Pond Test
penetration point
Application of MYK Induprime
EPW 44
ASO Joint
tape
1st Coat Application of 2nd Coat Application of
WPU 1K WPU 1K
Rain Protection
Final Pond Test Protection by
polythene sheet
Protective Soil Filling
Screed
Most Important Points need to be remembered
Two coats of
Two coats of Aquafin-UM Aquafin-IC @
@ 2Kg/sqm 1.2 kg/sqm
Protection Plaster
Food Grade
Epoxy-ECW
130
ASO Joint Tape
Bottom Slab
PCC
About Product
MYK Aquafin-UM is a Two component ,polymer modified, flexible
cementitious waterproofing membrane.
It can be applied on damp surface.
Seamless waterproof membrane system.
It has 30% elongation.
This membrane has excellent crack bridging up to 1mm.
UV resistance.
high bond strength 1 Mpa.
Permanently flexible.
Vapor diffusion resistance up to 2000.
Self curing membrane.
Solvent free, environment friendly.
No primer required.
High water pressure resistivity up to 50m.
Limitations
It requires a damp substrate while application.
Concrete substrate should be at least 28 days old at the time of
application.
Application should be avoid when ambient temperature is below 5° C.
Need to protect application when temperature is above 30 ° C to
prevent premature surface drying and shrinkage cracks.
Mixed composition should be used with in 60 minutes.
Second coat to be done when first is sufficient hardened.
Proper protection to be taken to protect the membrane from
mechanical damages.
While raining need to cover coating area which is under setting time.
Ph S
ot ite
og
rap
hs
Corner/Edge sealing Surface
Preparation
Surface in SSD condition Lumps Free Mixing Of
Aquafin-UM
ASO Joint Tape
1st Coat Application of 2nd Coat Application of
Aquafin-UM Aquafin-UM
Most Important Points need to be remembered
Two coats of
Aquafin-IC @
1.2 kg/sqm
Dry Shake of
Aquafin-IC @
1.2 kg/sqm
Bottom
Slab
PCC
About Product
MYK Aquafin-IC is a single component coating .
Easy to apply on substrate.
Seamless waterproof membrane system.
Can be use on damp surface.
Permanently active.
This membrane has crack bridging up to .4 mm.
Chloride free.
High compressive strength 25mpa @ 28 days.
Ph S
ot ite
og
rap
hs
Corner/edge Surface in SSD
sealing Condition
Lumps Free Mixing Of Aquafin-IC
1st coat application of 2nd coat application of
Aquafin-IC Aquafin-IC
Curing
Th
a nk
s