Professional Documents
Culture Documents
SSS Guideline
SSS Guideline
Tampa-Orlando Market
Rejection Concerns
SSS Approach
Familiarize Changes in the Site Configuration
Using the latest RFDS, check if there are any changes in the following
o Radio module location (ground or top)
o Radio module type
o Antenna model
Conduct Parameter Audit
compare pre/post values of the following settings: (pre values are as per baseline period)
o Power related parameters
o RET
o LMS parameters
o Handover parameters
Set RET/parameter settings to PRE values if needed/possible
Analyze degraded KPIs
Implement RET/parameter changes to rectify KPI degradation
Fine Tune changes to achieve optimum impact
Revert changes that does not yield positive impact
Familiarize Changes in Site Configuration
Identify any changes in the config and it’s possible impact in the performance o the site
Familiarize Changes in Site Configuration
In this example, lot of changes in the physical aspect of the site was done.
SECTOR B - - 46 - - - - - - - 43 40 40 - - -
SECTOR C - - 46 - - - - - - - 43 40 40 - - -
Conduct Parameter Audit
Compare pre-post values to identify any changes that may have impact in the performance o the site.
Analyze Degraded KPIs
Correlate changes in the site with changes in KPI trend to be able to apply appropriate actio
VoLTE Erlangs
500
450
400
350
300
250
200
150
100
50
0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02 2 02
1/ 3/ 5/ 7/ 9/ 2/ 4/ 6/ 8/ 0/ 2/ 4/ 6/ 8/ 0/ 2/ 4/ 6/ 8/ 0/ 1/ 3/ 5/ 7/ 9/ 1/ 3/ 5/ 7/ 9/
/2 /2 /2 /2 /2 /0 /0 /0 /0 /1 /1 /1 /1 /1 /2 /2 /2 /2 /2 /3 /0 /0 /0 /0 /0 /1 /1 /1 /1 /1
02 02 02 02 02 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 04 04 04 04 04 04 04 04 04 04
Source MB Cap LB Cov MB Cov LB Cap Source MB Cap LB Cov MB Cov LB Cap
hysThreshold2InterFreq 1.0 1.0 1.0 1.0 hysThreshold2InterFreq 1.0 1.0 1.0 1.0
threshold2InterFreqQci1 -111 -87 -87 -90 threshold2InterFreqQci1 -111 -87 -87 -90
threshold2aQci1 -110 -86 -86 -89 threshold2aQci1 -110 -86 -86 -89
threshold2InterFreq -119 -87 -87 -119 threshold2InterFreq -119 -87 -87 -119
threshold2a -118 -86 -86 -118 threshold2a -118 -86 -86 -118
targetLoadPdcch 80 80 80 80 targetLoadPdcch 80 80 80 80
maxPdcchAgg 16 16 16 16 maxPdcchAgg 16 16 16 16
maxPdcchAggHighLoad 16 16 16 16 maxPdcchAggHighLoad 16 16 16 16
iFLBA4ActLim 20 20 20 20 iFLBA4ActLim 20 20 20 20
LMS Settings_Portland
Source MB Cap LB Cov MB Cov LB Cap Source MB Cap LB Cov MB Cov LB Cap
hysThreshold2InterFreq 1.0 1.0 1.0 1.0 hysThreshold2InterFreq 1.0 1.0 1.0 1.0
threshold2InterFreqQci1 -111 -87 -87 -90 threshold2InterFreqQci1 -111 -87 -87 -90
threshold2aQci1 -110 -86 -86 -89 threshold2aQci1 -110 -86 -86 -89
threshold2InterFreq -119 -87 -87 -119 threshold2InterFreq -119 -87 -87 -119
threshold2a -118 -86 -86 -118 threshold2a -118 -86 -86 -118
targetLoadPdcch 80 80 80 80 targetLoadPdcch 80 80 80 80
maxPdcchAgg 16 16 16 16 maxPdcchAgg 16 16 16 16
maxPdcchAggHighLoad 16 16 16 16 maxPdcchAggHighLoad 16 16 16 16
iFLBA4ActLim 20 20 20 20 iFLBA4ActLim 20 20 20 20
UMTS Power Settings
1.SRVCC Status check & necessary action depending upon clutter Blanket approval ,
1. To ensure proper LMS Seek help from
( i.e rural sites should be active , approval req.to deactivate) Rural site SRVCC to setting is run Inayath
IFLBretry timer & Threshold2wcdma & geran seek approval
2. Start of physical opti. If possible ,till the required iterations. As Blanket approval for Blanket approval for 2G/
3G
per the guidelines of market +/- 1 , Further req. 2. Physical Opti. If viable +/- 2 , Further req. LTE coverage
Approval Approval
3.Tune of Cpich power ( adhering to market guidelines i.e least 3. Deactivating the idle
value ot be 28.1 in steps of 1 or 2 max , inter site distance being Blanket approval mode balance & tuning of Blanket approval
3 km max) IFLBchecktimer
4. In case L600 is high on
4.Try enhancing the footprint of LTE ,if approved boost changes
Approval required Traffic ,please check on
from market . Assuming RET of LTE & UMTS are clubbed footprint if its justifiable
5. Parameter Changes to hold traffic on LTE Approval required
Boosting till 4.77 for mid band ( both band must be at same
Approval required
value ), L6 upto 3 and nothing for L7
Deboosting approval required Approval required
Additional Information
Combo KPI
Optimization Process SSS Checklist
THANK YOU