Professional Documents
Culture Documents
C1D2 Introduce 0727
C1D2 Introduce 0727
C1D2 Introduce 0727
JAY WU 2022.07.28
危險場所定義
危險場所定義
危險環境內之設備
在危險環境內安裝的設備會因為其所處環境 , 自
身運作而導致爆炸的可能性
危險場所定義
Division System Zone System
Region: North America ONLY Region: North America/ATEX/IECEx/Global
Class I, Division 1 Zone 0
Likely to be present continuously, intermittently, Explosive gas atmosphere present most or all of
or periodically during normal operation; the time, e.g. within storage tanks
Zone 1
Explosive gas atmosphere present occasionally in
normal operation, e.g. around dispensing
operations, sampling points and vents
Class I, Division 2 Zone 2
- not likely to occur in normal operation and if Explosive gas atmosphere only present in
they do occur, they will exist for a short time abnormal
only conditions, e.g. leaking seals and pipe joints
- adjacent to a Class I, Division 1 location from
which explosive gas atmospheres could be
communicated
危險場所定義
Division System Zone System
Region: North America ONLY Region: North America/ATEX/IECEx/Global
Class II / III, Division 1 Zone 20
-are likely to be present continuously, Explosive dust atmosphere, in the form of a
intermittently, or periodically during normal cloud of dust in air, is present most or all of the
operation; time
- the abnormal operation or failure of equipment Zone 21
might …..; or Explosive atmosphere present occasionally in
- combustible and conducting dust; normal operation
Class II / III, Division 2 Zone 22
- insufficient combustible dust in the air as a Explosive atmosphere only present in abnormal
result of malfunctioning of equipment ……; or conditions
- combustible dust accumulations sufficient to
interfere with the safe dissipation of heat……..
危險場所定義
Division System Zone System
Class Group Material Equipment group
I A Acetylene 乙炔 IIC
(flammable gases
and vapours) B Hydrogen 氫氣 IIB + H2
C Ethylene 乙烯 IIB
D Propane 丙烷 IIA
II E Metal dust IIIC
(flammable dusts) F Coal dust
G Grain dust IIIB
III (ignitable fibres) - Fibres IIIA
C1D2 防護要求
Make/Break 元件
常見 Make/Break 元件有繼電器 , 斷路器 , 可變電
阻 , 開關 , 按鍵 , 連接器等
C1D2 防護要求
Make/Break 元件須符合下列其一要求
1. 無火花元件
2. 使用在低能量電路
3. 密封元件
C1D2 防護要求
無火花元件
1. 有機械性結構使連接能不單靠摩擦力固定
2. 能承受 15N 拉力測試
C1D2 防護要求
低能量電路
1. 進行火花測試
2. 量測或計算之電壓 , 電流與儲能元件在標準限
制值之內
C1D2 防護要求
密封元件要求
1. 密封元件其內部氣體容積不可超過 100 立方公
分
2. 密封使用熱塑性材料必須不低原該位置之最高
溫度
C1D2 防護要求
電池要求
電池以及相關電池本身外用來限制短路電流低於點燃
1. 電流限制元件需要有防尺損壞的相關方式
2. 電流限制元件安裝須能為職組裝完整性
3. 電池置放空間須符合火花測試或額外警語限制電池僅於
非炸環境更換
4. 電池須標示電池形式 電壓 製造商 型號等資訊
5. 若為手持式裝置 , 落下測試電池不能彈出
C1D2 防護要求
外殼要求
NEMA ANSI/IEC 60529/ CAN/CSA C22.2 No. 60529 ( 產品外殼機構防護等級國際標準 )
的 IP54 等級或更佳,或 UL 50E/ CAN/CSA-C22.2 No. 94.2 ( 電氣設備外殼 – 環境考慮
評估標準 ) 及 UL 50/ No. 94.1 ( 安裝在非危險環境之電氣設備外殼 ( 不含環境考慮 )
評估標準 ) 的 Type 3 等級或更佳。
章節 16.2.1 ── 可攜式產品應通過墜落測試以及先期的老化測試,老化測試條件如下:
1. 置放於高溫處 7 天,老化溫度為非金屬材質外殼的最高工作溫度 (max. service
temperature) 高 10°C 以上,但至少為 70°C 。
2. 緊接著進行低溫老化,溫度為產品的最低額定環溫 (min. ambient temperature) 。
前述的墜落測試應在老化測試結束的 10 分鐘之內執行,並且自至少 1 公尺之高度墜落
至平整混凝土表面 6 次,每次撞擊應為相異點。此測試結果不應損及產品而導致保護
型式失效,且不應發生電池脫落之狀態。