Professional Documents
Culture Documents
Unit 1 DC Network Theorems
Unit 1 DC Network Theorems
05/29/2024
Current
Curtesy: https://kaiserscience.wordpress.com
05/29/2024
Current
Curtesy: https://gfycat.com/
05/29/2024
Electrical Load & Power
Curtesy: https://commons.wikimedia.org/
05/29/2024
Basics
Current: “Rate of flow of electric charge.”
Charge
I Coulombs/Sec or Ampere
time
Note:-
1. Direction of current is same as the direction of motion of +Ve charge or opposite to the direction of motion of –Ve
charge.
Voltage: “Energy required in transferring a charge of one coulomb from one point to another
point.”
Energy(W)
V Joule/Coulomb or Volts
Charge(Q)
EMF (Electromotive force): “The EMF of a voltage source is the energy imparted by the
source to each coulomb of the charge passing through it.”
Energy(W)
E Joule/Coulomb or Volts
Charge(Q)
05/29/2024
Basics
Potential Difference: “The pd between two points is the energy required in transferring a charge
of one coulomb from one point to another point.”
Energy(W)
pd Joule/Coulomb or Volts
Charge(Q)
Voltage drop: “The voltage drop between two points is the decrease in energy required in
transferring a charge of one coulomb from one point to another point.”
Energy(W)
Voltage drop Joule/Coulomb or Volts
Charge(Q)
05/29/2024
Basics
Resistance: “Electric resistance is the property of material which offers opposition to the flow of
current and dissipates energy.”
l
R Ohm or (Law of resistance)
a
Where l Length of the wire
a cross sectional area of the wire
Resistivit y or Specific Resistance of the material
Note:-
1. Resistance also depends on temperature.
Ohm’s Law: “The current passing through a conductor is directly proportional to potential
difference across its ends provided physical conditions are same.”
I V
1
Or I V
R
Or V IR
05/29/2024
Basics
1 a a
G mho, 1 , Siemens
Resistance (R) l l
05/29/2024
Basics
Series Circuit:
R1 R2 R3 Req
I V1 V2 V3 I
V V
(b)
(a)
Fig.1
Total voltage V = V1 + V2 + V3
IReq IR1 IR2 IR3
Req R1 R2 R3
Note:-
1. Same current means resistances are in series.
05/29/2024
Basics
Example 1: Three resistors are connected in series across a 12V battery. The one resistance has
a value of 1 ohm, second has a voltage drop of 4 Volts & third has power dissipation of 12 W.
Calculate value of each resistance & circuit current.
Solution: Hint V V1 V2 V3
12 I 4 12 / I
I = 2 Or 6 Amperes
When I=2 Amp
R1 = 1 R2 = 2 R3 = 3
When I=6 Amp
R1 = 1 R2 = 2/3 R3 = 1/3
05/29/2024
Basics
Parallel Circuit: R1
I1
Req
I2 R2
I
V
I3 R2 (b)
I
V
(a) Fig.2
V V V
We know I1 I2 I3
R1 R2 R3
Total current I I1 I 2 I 3
V V V V
Req R1 R2 R3
1 1 1 1
Req R1 R2 R3
Note:-
1. Same voltage means resistances are in parallel.
2. If two resistances are in parallel and R1=R2=R then
R
Req
2
05/29/2024
Basics
Series Parallel circuit:
I4 R4
I1 R1
I3 R3 I5 R5
I2 R2 B D
C
A I6 R6 RAD
A RAB B RBC C RCD D
I VAB VBC VCD I
I
V V V
(a) (b) (C)
(c)
Fig.3
R1R2 1 1 1 1
RAB RBC R3
R1 R2 RCD R4 R5 R6
V
So RAD RAB RBC RCD And I
RAD
VAB IR AB From fig.3b
VBC IRBC From fig.3b
VCD IRCD From fig.3b
05/29/2024
Basics
VAB V V
I1 I 2 AB I 3 BC I From fig.3a
R1 R2 R3
V V V
I 4 CD I 5 CD I 6 CD From fig.3a
R4 R5 R6
Power consumed by whole circuit
P I 2 RAD From fig.3c
Or I 2 R AB I 2 R BC I 2 R CD From fig.3b
Or I12 R1 I 22 R2 I 32 R3 I 42 R4 I 52 R5 I 62 R6 From fig.3a
05/29/2024
Basics
Example 2: Two resistances of 20 & 30 ohms respectively are connected in parallel. These two
parallel resistances are further connected in series with a third resistance of 15 ohm. If current
through 15 ohm resistance is 3 Amperes. Find
(i) Current through 20 & 30 ohm resistances
(ii) Voltage across whole circuit I1 20
(iii) Total power consumed. 3 A 15
Solution: Hint I2 30 B C
Req = (20||30) + 15 A
= 12 + 15 =37
V AB 12x3 36 I
(i) I 1 36 / 20 1.8 A I 2 36 / 30 1.2 A V
(ii) V AC V AB VBC 36 15 3 81Volts Fig. 4
(iii) Power = VI = 243 Watts
05/29/2024
Basics
Circuit or Network Elements: R, L, C
Fig.5-T-Network
3. So every network may not be circuit (i.e. T-Network) but every circuit is a network.
Mesh: “A closed path which does not have any closed path inside it.”
05/29/2024
Basics
Node: “It is a junction where 2 or more branches are connected together.”
Note:-
1. A junction where 3 or more branches connected together is known as principal node or essential node.
2. For example A B C
Loop but not Mesh
H
D
F E
Loop or Mesh Loop or Mesh
Fig.6
Total no of nodes = 6+2 = 8 (A, B, C, D, E, F, G, H)
No of principal nodes =2 (B & E)
No of Loops =3 (ABEFA, BCDEB, ABCDEFA)
No of Meshes =2 (ABEFA, BCDEB)
05/29/2024
Basics
Energy Sources:
Basically Two types
(A) Independent Energy Sources
a. Voltage Source
i. AC/DC
ii. Ideal/Practical
b. Current Source
i. AC/DC
ii. Ideal/Practical
(B) Dependent Energy Sources
a. Voltage Source
b. Current Source
05/29/2024
Basics
(A) Independent Energy Sources:
a. Voltage Source
r
V V
r
+
V +
_ V_
05/29/2024
Basics
a. Current Source
I I R
+ bI1 +
_
aV1 _
Volts Volts
05/29/2024
Basics
cV1 dI1
Amperes Amperes
05/29/2024
Basics
Kirchhoff’s Current Law (KCL):
“At any instant of time, the algebraic sum of currents at any node is zero.”
I 0
Or
“Total incoming currents = Total outgoing currents.”
05/29/2024
Basics
Consider following circuit
I1 R1 B I2 R2
A C
V2
R6 R3
I3 R4
V1
D
F E
Fig.10
05/29/2024
Basics
Example 3: In the following circuit calculate current in each branch by KCL & KVL (Fig.11a).
Solution:
B I1+I2
A C
I1 I2
2Ω 4Ω 2Ω 4Ω
6Ω 6Ω
40V 44V 40V 44V
F D
(a) E
(b)
Fig.11
05/29/2024
Mesh Analysis
Mesh Analysis:
Steps are
1. Identify the all meshes
2. Assume some mesh current in each mesh (clockwise or anticlockwise)
3. Apply KVL in each mesh.
4. Solve the above equations.
2Ω 2 2 R3
2Ω R3
10V 5A 10V I1 I2 I3
5A
Let the three meshes are having clockwise currents as shown in following figure
Apply KVL in mesh 1
10 2 I1 2( I1 I 2 ) 0 (1)
Apply KVL in mesh 2
2( I 2 I1 ) 4( I 2 I 3 ) 0 (2)
Clearly From mesh 3
I 3 5 A (3)
Solving (1), (2) & (3) I 1 1A I 2 3
Current in R3 = I2-I3 = (-3)-(-5) = 2 A
05/29/2024
Node Analysis
Node Analysis:
Steps are
1. Identify the all Principal Nodes
2. Assume one node as reference node (Voltage of this node = 0 Volts)
3. Assume some node voltages for other remaining nodes w.r.to reference node.
(V1 , V2, V3 etc).
4. Assume some branch currents in different branches.
5. Apply KCL at different nodes and make the equations in terms of node
voltages and circuit elements.
6. Solve the above equations.
V1 40 0 V1 44 0 V1 0
0
2 4 6
372 I1 V1 I3
V1 Volts I2
11
34 2 4
So I1 A 6
11 40V 44V
28
I2 A Reference or
11
Fig.14 Datum Node, V=0
05/29/2024 62
I3 A
11
Node Analysis…
05/29/2024
Superposition Theorem
Superposition theorem:
“In a linear circuit, containing more than one independent energy
source, the overall response (Voltage or current) in any branch of the circuit is equal to the sum
of the response due to each independent source acting one at a time while making other sources
in-operative.”
I I’ I”
R1 R2 R1 R2 + R1 R2
I1 I1
V1 V1
Fig.16
05/29/2024
Superposition Theorem…
Example 8: Solve example 5 by superposition theorem.
Solution:
2 I’ 2 I”
2 R3 2 R3
10V 5A
(a) (b)
Fig.17
Consider 10 V Voltage source only (Fig.17a)
2 10
I' 1 Amps
2 4 2 (2 || 4)
05/29/2024
Superposition Theorem…
Example 9: Find I in the following circuit by superposition theorem (Fig.18a).
Solution:
5
20A I
8 4 12
10V 40 V
(a)
Solution: Consider 20A current source only (Fig.18b)
By current division rule 5 I1
8 Ω I’
I 1 20 10 20A
8 5 ( 4 || 12 ) 8 4 12
Again by current division rule
4 5
I' 10 Amps (b)
4 12 2
05/29/2024
Superposition Theorem…
Consider 10V Voltage source only (Fig.18c) 5 I2
I”
10 5 8 4 12
I 2
8 5 (4 || 12) 8
10V
Ω
By current division rule
(c)
4 5 5
I" Amps
4 12 8 32
A A
Any Linear
Two IL RTh IL
RL RL
terminals
Network VTh
B B
(b) Thevenin’s Equivalent
(a)
Circuit
Fig.19
Where
VTh = Open circuit voltage at load terminals
RTh = Equivalent resistance of the network at load terminals when the
sources are made in-operative.
VTh
And IL
RTh RL
05/29/2024
Thevenin’s Theorem…
Example 10: Solve example 5 by Thevenin’s Theorem.
Solution:
VTh
2 2
2 Ω 2 VTh
RTh
10V Ω 5
A
V=0
(a)
(b)
Fig.20
A A
20 Ω 3Ω 20 Ω 3Ω
5Ω 5Ω RTh
30V
2Ω B 2Ω B
(a) (b)
05/29/2024
Thevenin’s Theorem…
30
VTh 3 4 5
20 5
VTh 6 Volts B
RTh
So Its Thevenin’s equivalent circuit is Fig.21
shown in fig.21d, It is to be noted here VTh
that terminal B is +Ve and A is –Ve.
A
(d) Thevenin’s Equivalent
Circuit
05/29/2024
Norton’s Theorem
Norton’s theorem:
“Any linear two terminal circuits can be replaced by an equivalent
network consisting of a current source (I N) in parallel with a resistance (RN).”
A A
Any Linear IL
IL
Two IN RN
RL RL
terminals
Network
B B
(b) Norton’s Equivalent
(a) Circuit
Fig.22
Where
IN = Isc = Short circuit current at load terminals
RN = Equivalent resistance of the network at load terminals when the
sources are made in-operative (=RTh).
RN
And IL IN
R N RL
05/29/2024
Norton’s Theorem…
Example 12: Solve example 5 by Norton’s Theorem.
Solution:
Find RN (Fig.22a) 2
Same as RTh RTh (2 || 2) 1 2 IN = Isc
Find IN (Fig.22b) 5A
10V
10
I N 5A A
2 (a)
I N 10 Amps A
IL
RN IN RN RL
IL IN
R N RL
1 B
IL 10 2 Amps
1 4 (b) Norton’s Equivalent
Circuit
Fig.23
05/29/2024
Norton’s Theorem…
Example 13: Find current and voltage across 5 ohm resistance by Norton’s theorem (Fig.24a).
Solution:
4Ω 3Ω 4Ω 3Ω
2Ω 5Ω 2Ω RN
6A
15V
(a) (b)
Find RN (Fig.24b) V1
13 4Ω 3Ω
RN (4 || 2) 3
3 2Ω 6A IN
Find IN (Fig.24c) 15V
Apply KCL at node V1
V1 15 0 V1 0 V 0
6 1 0
4 2 3 (c)
05/29/2024
Norton’s Theorem…
117 A
V1 Volts IL
13
V 0 IN RN RL
IN 1 3Amps
3
(13 / 3) 13 B
IL 3 Amps (d) Norton’s Equivalent
(13 / 3) 5 9
Circuit
13 Fig.24
VL I L RL Volts
3
05/29/2024
Norton’s Theorem…
Example 14: Find Norton’s equivalent circuit at A-B of example 11.
Solution: V1 12 V
Find RN (Fig.21b)
20 Ω 3Ω
RN RTh 20 || 5 3 2 9
5Ω IN
Find IN (Fig.25a) 30V
Apply Node analysis at node V1 after applying 2Ω
source transformation
V=0
V1 30 0 V1 0 V 1 12 0
0 (a)
20 5 3 A
76
V1 V
3 IN RN
V 12 0 2
IN 1 A
20 3 B
Fig.25 (b) Norton’s Equivalent
Circuit
05/29/2024
Norton’s Theorem…
Example 15: Use Norton’s theorem to find out current in 6 ohm resistance and verify it with
Thevenin’s theorem (Fig.26a).
Solution:
4 12 V
2A 2 6
(a)
By Norton’s Theorem: 4
Find RN (fig.26b) A
RN=2 Ohms 4
2
Find IN (fig 26c)
Clearly from mesh 1 B
I1 = 2 A (b)
Apply KVL in mesh 2
2(I2+I1)-12=0
So I2 = IN = 4 Amp 4 I3
2
IL 4 1 Amps 4 12V
26 2A 2
05/29/2024 I1 I2
Norton’s Theorem…
By Thevenin’s Theorem:
4
Find RTh (fig.26b)
RTh = RN=2 Ohms A
4 12V
Find VTh (fig 26d) 2A 2
Clearly from mesh 1 I1
I1 = 2 A B
So VTh = 12-2I1= 8 Volts (d)
8 Fig.26
IL 1 Amps Hence verified
26
05/29/2024
Maximum Power Transfer Theorem
Maximum Power Transfer Theorem:
“Maximum power is transferred by a circuit to a load
resistance (R L), when R L is equal to Thevenin’s equivalent resistance (RTh) of that network.”
So for maximum power
A
R L = RTh
And maximum power will be RTh IL
VTh2 RL
Pmax VTh
4 RL
B
Fig.27 Thevenin’s Equivalent
Circuit
05/29/2024
Maximum Power Transfer Theorem…
Proof:
Load current will be
VTh
IL (1)
RTh RL
Power
P I L2 RL
2
VTh
RL
R
Th RL
RL
VTh2 ( 2)
( RTh RL ) 2
Differentiating equation equa (2) w. r. t. R L and put dP/dRL = 0
2 ( RTh RL ) 1 RL ( RTh RL )
2
dP
VTh (3)
dRL ( RTh RL ) 4
RL-RTh = 0
Or RL = RTh Put this in equation (2)
VTh2
Pmax
4 RL
05/29/2024
Maximum Power Transfer Theorem…
Example 16: Find out the value of R for maximum power transfer to this load and find out the
value of maximum power (fig.28a).
Solution:
6V
6
2A 15 3 R
8V
(a)
6
Find the RTh (Fig.28b) 15 3 RTh
21
RTh (15 6) || 3
8
Find VTh (Fig.28c) (b)
6V
Clearly I1 = 2 A
6 +
By KVL in mesh 2 2A 15 3
I I VTh
6 I 2 6 3I 2 15( I 2 I1 ) 0 1 2
8V -
So I2 = 1 A
VTh 3I 2 8 11Volts (c)
Hence for maximum power transfer to R Fig.28
2
05/29/2024 21 V
R L = RTh and Pmax Th 11 .524Watt
8 4R
Star-Delta Transformation
Star-Delta and Delta-Star transformation:
1
1
R1 R31 R12
R3 R2
3 R23 2
3 2
(b) Delta ( ) Connection
(a) Star or WYE (Y)
Connection
Fig.29
05/29/2024
Star-Delta Transformation…
Proof:
Equivalent resistance at 1 - 2Y Equivalent resistance at 1 - 2
R1 R2 R23 R31 || R12
R12 R23 R31
R1 R2 (1)
R12 R23 R31
Similarly
Equivalent resistance at 2 - 3Y Equivalent resistance at 2 - 3
R2 R3 R12 R31 || R23
R R R31
R2 R3 23 12 (2)
R12 R23 R31
Equivalent resistance at 3 - 1Y Equivalent resistance at 3 - 1
R3 R1 R12 R23 || R31
R R R23
R3 R1 31 12 (3)
R12 R23 R31
05/29/2024
Star-Delta Transformation…
Delta to star
Equation (1) + (2) + (3)
05/29/2024
Star-Delta Transformation…
Star to Delta
From Equation (5), (6) & (7)
R12 R23 R31 R12 R23 R31
R1 R2 R2 R3 R3 R1
R12 R23 R31 2
R12 R23 R31
R1 R2 R2 R3 R3 R1 (8)
R12 R23 R31
R R R2 R3 R3 R1
(8) / (7) R12 1 2
R3
R1 R2 R2 R3 R3 R1
(8) / (5) R23
R1
R R R2 R3 R3 R1
(8) / (6) R31 1 2
R2
05/29/2024
Star-Delta Transformation…
Example 17: Find the equivalent resistance between the terminals a-b of the bridge circuit of the
fig.30a
Solution: a
R1=2
a 4 6
2
R3=2/3 R =12
b 10 14 b 10 14
(a) (b)
Fig. 30
Apply delta to star transformation
R12 R31 6 4
R1 2
R12 R23 R31 12
R12 R23 6 2
R2 1
R12 R23 R31 12
R23 R31 4 2 2
R3
R12 R23 R31 12 3
2
Rab 2 1 14 || 10
3
05/29/2024 Rab 8.234
Every side of the problem is not so hard,
there is some softer way also
05/29/2024