Professional Documents
Culture Documents
附加 13 - Practical Physics
附加 13 - Practical Physics
13 – Practical Physics
13 – PRACTICAL PHYSICS
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 277
Working safely
► When carrying out physics experiments, you
need to be able to do the following:
Handle equipment and materials safely.
Follow instructions carefully.
Change how you carry out each step of
an experiment, depending on what
happened the time before. ▲A yellow bunsen
► Here are some reminders about how to
flame is easier to see
work safely with different types of equipment: than a blue one.
Bunsens and tripods
If a bunsen burner is alight, but not in use, always leave it on the
yellow flame setting so that the flame can be seen.
Make sure that bunsens and tripods have a heatproof mat
underneath.
Give a hot tripod plenty of time to cool down before attempting to
move it.
Don’t attempt to move a tripod when there is a beaker resting on it.
13.01 – Working Safely
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 278
Glass thermometers
Don’t put glass thermometers where they can roll off the
bench.
Keep glass thermometers away from bunsen flames.
Support thermometers safely: see Safe support below.
Mercury, used in some thermometers, is toxic. If a
thermometer breaks and mercury runs out, don’t handle it.
Glass tubing
Never attempt to push glass tubing (or glass thermometers)
through a hole in a bung. The laboratory technician has a
special tool for doing this.
Always handle hot glass tubing with tongs. Rest it on a
heatproof mat; don’t put it straight on the bench.
Hot glass tubing can stay hot for a long time. Give it plenty
of time to cool down before you attempt to pick it up.
13.01 – Working Safely
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 278
Safe support
When clamping a test-tube, don’t
overtighten the clamp. And make
sure that the clamp has soft pads to
touch against the glass. This also
applies when clamping a glass
thermometer.
In experiments where you have to
suspend a load, make sure that the
supporting clampstand is stable
enough to take the heaviest load ▲In experiments
you will be using. You may need to like this, make sure
that the apparatus is
weigh it down for this, as shown in stable enough to
the diagram on the left. support the heaviest
13.01 – Working Safely
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 279
Safe support
Before making any changes to the wiring in your
circuits, always switch off the power or disconnect the
battery.
Remember: low voltage circuits may not give you a
shock, but they can cause bums if the current is too
high and a wire overheats.
Never make a direct connection across the terminals of
▲Emergency!
a battery. Don’t put wires or tools where they might
connect across the terminals. But the first job is
to switch off the
If a mains appliance is faulty, switch off the power and power and pull
pull out the plug. Don’t change the fuse. Ask the out the plug.
laboratory technician to deal with the fault.
Electrical fires: see slide 8.
In many modern laboratories, the mains circuits are protected by RCDs
(residual current devices), so the risk of shocks is reduced. But...
If someone has been electrocuted, and is still touching the faulty
appliance, don’t touch the person. Switch off the power and pull out the
plug.
13.01 – Working Safely
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 279
Eye protection
Always wear eye protection (e.g. safety
goggles) when:
o stretching metal wires or plastic cords
o breaking or grinding solids (e.g. rock
samples)
o heating liquids
o dealing with acids, alkalis, or any other liquid chemicals that
might splash.
Light
Don’t look directly into a laser beam or other source of bright
light. Don’t stand where laser light might be reflected into your
eyes.
If you need to study the Sun’s image, project it onto a card.
Never look through a telescope or binoculars pointing straight
at the Sun - even if there is a filter in front.
13.01 – Working Safely
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 279
Flammable
Radioactive sources liquid
The radioactive sources used in school
laboratories should always be sealed.
Radioactive sources should be kept well away Hot
from the body, and never placed where they are Water
pointing at people.
Fire
Don’t heat flammable liquids (e.g. methylated
spirits) over a bunsen. If heating is required, a
water bath should be used - with hot water
heated well away from the experiment. ▲The only
Don’t throw water on burning liquids (e.g.
safe way to heat
methylated spirits). Smother the fire with a fire a flammable
blanket or use a carbon dioxide extinguisher. liquid is to use a
Don’t throw water on electrical fires. Switch off water bath
the supply and use a carbon dioxide
extinguisher.
13.02 – Planning and Preparing
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 280
Making a prediction
► You may have an idea of what you expect to
happen in your enquiry. This prediction is called
your hypothesis. You should write it down. It may
not be right! It is just an idea. The aim of your
procedure is to test it.
13.02 – Planning and Preparing
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 280
Key variables
► These are the variables that can affect what happens
in an experiment. You must decide what they are. For
example, in the nichrome wire experiment, length is
one of the key variables because changing the length
of wire changes the resistance.
► You must also decide how to measure the variables,
and over what range. For example, in planning the
nichrome wire experiment, you would have to:
decide what the highest voltage and current
values should be (safety must be considered
here)
decide what lengths of wire to use.
13.02 – Planning and Preparing
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 281
Controlling variables
► A fair test When doing an experiment, you should change
just one variable at a time and find out how it affects one
other. If lots of variables change at once, it will not be a
fair test.
► For example, if
you want to find
out how the length
of a wire affects its
resistance, it
wouldn’t be fair to
compare a long,
thick wire with
short, thin one.
13.02 – Planning and Preparing
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 281
Final preparations
► Decide what equipment you
need, how you will arrange it,
and how you will use it.
► To help your planning, you
may need to carry out a trial
run of the experiment. Before
you do this, make sure that
all your procedures are safe.
► Prepare tables for your
readings before you start
your experiments. Look at the
next spread on getting the
evidence before doing this.
13.02 – Planning and Preparing
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 281
Uncertainties
► No measurement is exact. There is always
some uncertainty about it. For example,
you may only be able to read a voltmeter to
the nearest 0.1 V.
► Say that you measure a voltage of 2.3 V
and a current of 1.2 A. To work out the
resistance in ohms (Ω), you divide the
▲You can only
voltage by the current on a calculator and
read this voltmeter
get... to the nearest 0.1
1.916 666 7 V.
► This should be recorded as 1.9 Ω. Uncertainties in your voltage
and current readings mean that you cannot justify including
any more figures. In this case, you are giving the result to two
significant figures.
13.03 – Measuring & Recording
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 282
Reading scales
► On many instruments, you have to
judge the position of a pointer or level
on a scale and work out the
measurement from that. Here are
some ways of making sure that you
take the correct reading:
A. Using a glass thermometer to
measure the temperature of a liquid:
keep the liquid well stirred, give the
thermometer time to reach the
temperature, and keep the lamp in the
liquid while you take the reading.
13.03 – Measuring & Recording
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 283
0.79 mV
86 kPa
13.04 – Dealing with Data
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 284
Drawing a graph
► A graph can help you see trends in your data.
► Choosing axes Decide which variable to put along the bottom
axis. Usually, it is the one you chose to vary by set amounts -
the length of nichrome wire, for example. This is the
independent variable. The resistance would be the
dependent variable because its value depends on the length
you chose. It goes up the side axis.
► Choosing scales Check your
highest readings, then choose the
largest scales you can for your
axes.
► Labelling axes Along each axis,
write in what is being measured
and the units being used.
13.04 – Dealing with Data
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 284
Drawing a graph
► Drawing the best line Because of uncertainties, the points on
a graph will be uneven. So don’t join up the points! Instead,
draw the straight line or smooth curve I that goes closest to
most of them. This is called a line of best fit. Before you draw
it:
Decide whether the line should go through the origin.
Decide whether any readings should be rejected.
Some may be so far out that they
are probably due to mistakes
rather than uncertainties. See if
you can find out why.
► From the way points scatter about a
line of best fit, you can see how
reliable your readings are, But for this,
you need plenty of points.
13.04 – Dealing with Data
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 284
Reliability
► In reaching your conclusions, remember that there are
uncertainties in your measurements, and variables that you
may not have allowed for. So your results can never prove
your original prediction. You must decide how far they
support it.
► If you think that your results are unreliable in any way, see if
you can explain why.
► You may have some results which do not agree with the
others and look like
mistakes. These are
called anomalous
results. Try to explain
what caused them.
13.05 – Evaluating & Improving
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 285
Suggesting improvements
► Having completed your procedure, suggest ways of
improving it so that your conclusions are more reliable.
Looking further
► Suggest some further work which might produce extra
evidence or take your procedure further.
13.05 – Evaluating & Improving
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 285
Wet or dry?
► The makers of a well-known brand of soft tissue
paper claim that their tissues are just as strong wet
as dry. Are they right? Plan and carry out an
enquiry to test their claim.
► Start by thinking about the
following:
What is meant by the ‘strength’ of
a tissue? Do you need use a
whole tissue? When comparing
tissues, how can you make sure
that your test is fair?
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 286
Fine or coarse?
► Coarse glasspaper (‘sandpaper’) rubs through a
wooden surface more quickly than fine glasspaper.
But does it produce more friction? Plan and carry out
experiments to find out.
► Start by thinking about the following:
► How can you measure the frictional force when
glasspaper is rubbed on wood? How can you keep
the glasspaper pressed against the
wood? Will the force used to press
the glasspaper against the wood
affect the result? How can you make
sure that your test is fair?
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 286
Pendulum
► The time of one complete swing of a
pendulum is called its period.
► The period of swing might be affected by
these factors: the mass of the bob, the
amplitude (size) of the swing, the length of
the pendulum.
► Plan and carry out an enquiry to find out
which factors affect the period.
► Start by thinking about the following:
Stretching rubber
► A company wants to market a cheap
spring balance for weighing letters.
Their designer suggests that, to save
money, they could use a rubber band
instead of a spring.
► Their technician says that this would
be unsatisfactory because rubber
bands change length and
‘springiness’ once they have been
stretched.
► Who is correct? Plan and carry out
an enquiry to find out.
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 287
Bouncing ball
► Some table tennis balls have more ‘bounce’ than
others. Plan and carry out an enquiry to compare
the bounce of two table tennis balls.
► Start by thinking about the following:
What is meant by ‘bounce’?
What do you need to measure?
When comparing the balls, how
can you make sure that your
test is fair?
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 287
Parachute design
► The diagram on the right shows a
simple model parachute. Plan and
carry out an enquiry to find out if
there is a link between the design
of the parachute and the speed at
which it falls.
► Start by thinking about the following:
Shape and area are two possible features of the
design. Will you investigate both? How will you
make sure that your tests are fair? How will you
work out the speed of fall?
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 287
Double-glazing
► In cooler countries, people fit double-glazing in their houses
because two layers of glass, with air between, are supposed
to lose thermal energy (heat) more slowly than a single
layer. But does double-glazing cut down
thermal energy loss? Plan and carry out
an enquiry to find out.
► Start by thinking about the following:
How are you going to set up a double
layer of glass with air between? What
will you use as a source of thermal
energy? How will you tell whether the
flow of thermal energy is reduced when Glass
the extra layer of glass is added? Will Glass
your test be fair? Air
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 288
Salt on ice
► During winter, salt is often sprayed on the roads to melt the
ice. Pure ice has a melting point of 0°C. Adding salt to ice
affects the melting point.
► Plan and carry out experiments to find out how the melting
point of ice changes when salt is mixed in. Find out if there
is a connection between the melting point and the
concentration of salt in the ice. (The concentration can be
measured in grams of salt per cm3 of ice.)
► Start by thinking about the following:
How will you make sure that the salt
and ice are properly mixed? How
are you going to measure the
melting point?
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 288
Apparent depth
► The person in the diagram on the right is looking at a pin on
the bottom of a beaker of water. Light from the pin is refracted
(bent) when it leaves the water. As a result, the water looks
less deep than it really is and the pin appears closer to the
surface than it really is.
► Plan and carry out an experiment to find the
apparent depth of some water in a beaker.
► Start by thinking about the following:
If you look at a pin in some water, it is an
image of the pin which you are seeing. How
can you locate the position of this image?
Could you use a similar method to that used
to find the position of an image in a mirror?
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 288
Ray Box
Current-voltage investigations
► Plan and carry out experiments to find out how the
current in each of the following depends on the
voltage across it:
1) nichrome wire, kept at constant temperature
2) the filament of a lamp
3) a semiconductor diode.
► Start by thinking about the following:
How will you vary the voltage across each
component and measure the current in it? What
checks must you do to make sure that the current
in each component is safe, and does not cause
damage?
13.06 – Some Experimental Investigations
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 289
Making a resistor
► Resistors are used for keeping voltages and
currents at correct levels in electronic circuits.
► Using nichrome wire, make a resistor with a
resistance of 5 O.
► Start by thinking about the following:
Thermistor Investigation
► Thermistors have a resistance that varies considerably
with temperature. They can be used as temperature
sensors. Plan and carry out an experiment to find out
how the resistance of a thermistor varies between 0 °C
and 100 °C.
► Start by thinking about the following:
How will you change and control Thermistor
the temperature of the
thermistor? How will you
measure the resistance of the
thermistor? How will you make
sure that your circuit doesn’t
heat up the thermistor?
13.07 – Taking a Practical Test
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 290
?
13 – Summary
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 292
Use the list below to help you prepare for your practical test. You can either
photocopy it or print it from the file on the CD accompanying this book.
The page number, in brackets, tells you where to find more information.
Core and Extended Level
Check to make sure that you know how to do each of the following.
Most of these also apply if you are taking an alternative-to-practical
examination paper.
Identify key variables,
(page 280)
Explain why certain variables should be controlled,
(page 281)
Measure lengths to the nearest half millimetre using a rule,
(page 283)
Measure angles to the nearest half degree using a protractor,
13 – Summary
13.01 13.02 13.03 13.04 13.05 13.06 13.07 13 – Exam Questions Page 292
(page 36)
When using meters or other instruments with scales on them, be able
take readings that lie between the divisions on the scale,
(page 283)
Calculate simple areas and volumes: for example, the area of a
rectangle or triangle, or the volume of a rectangular block,
(page 15)
Record readings, or do calculations, with a suitable level of accuracy -
and not include too many significant figures,
(page 282)