Professional Documents
Culture Documents
4.weichai Genset Control System L1&L2
4.weichai Genset Control System L1&L2
Control System
1
目录
发电机组主要电器件介绍
1 Electrical Parts Introduction
控制器软件安装、设置及使用注意事项
2 Module Software Installation & Setting
2
发电机组主要电器件介绍
1 Electrical Parts Introduction
3
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
Control Panel
Generator set
4
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
Module/MCB/Charger/Re
热继电器
lays/Thermal Thermal relays
Relays/Contactors etc.
拓展模块
接触器 Expansion modules
Contactors
5
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
微型断路保护器(微断) : 一般安装在机组控制箱内,主要
作用是给控制屏线路及电器提供过载保护。
6
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
塑壳断路器
主要作用是接通和断开电路中的空载和负荷电流,以及
在故障时切断故障电流。
7
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
框架式空气断路器
主要作用是接通、承载以及分断正常、故障电路条件下
的电流。
8
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
双电源切换开关
简称“ ATS” ,主要作用将负载电路从一路电源切换到
另一路电源的电器,实现两路电源的自由切换。
继电器
主要作用是放大输出电路,用一个小电流,来控制一个大
的负载电流。
Relays
The main function is to amplify the output circuit and control a
large load current with a small current.
10
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
接触器
主要作用是接通和切断电路,常用于电动机作为控制对象。
Contactors
The main function is to turn on and off the circuit, and is often used
in the motor as a control object.
11
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
热继电器
主要作用是用于电动机或其它电气设备、电气线路的过载
保护的保护电器。
Thermal relays
The main function is to protect electrical appliances for overload
protection of motors or other electrical equipment and electrical
circuits.
12
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
浮充电源
主要作用是给蓄电池充电, 230V 交流电源输入, 12V
或者 24V 直流电源输出。
Battery Charger
The main function is to charge the battery, 230V AC
power input, 12V or 24V DC power output.
13
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
拓展模块
主要作用是配合机组控制器输入口,提供更多的输入口
检测。
Expansion modules
The main function is to cooperate with the input port of
the unit controller to provide more input port detection.
14
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
电流互感器
主要作用是可以把数值较大的一次电流,通过一定的变比
转换为数值较小的二次电流。
Current transformers
The main function is to convert the primary current with a
large value into a secondary current with a small value
through a certain transformation ratio.
15
1 . 发电机组主要电器件介绍
Electrical Parts Introduction
电压互感器
主要作用是用来进行电压测量、功率计算和设备保护等 。
Voltage transformer
It is mainly used for voltage measurement, power
calculation and equipment protection.
16
控制器软件安装、设置及使用注意事项
2 Module Software Installation & Setting
17
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
Generator set
Module-Deepsea 8620II
18
2. 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
19
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
DSE 深海软件下载到电脑以后,打开 DSE 设置软件,可通过“ USB 打印机数据线”与 DSE 控制器
建立连接,连接成功以后电脑会提示:
After the DSE software is downloaded to the computer, open the DSE setting software,
and you can connect to the DSE controller through the "USB printer cable".
Establish a connection, after the connection is successful, the computer will prompt:
点击 可以进行数据的读取,点击 可以进行数据的写入。
20
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
启动定时器、条件设置和控制
逻辑图
Instructions:
Start timer, condition
setting and control logic
diagram
21
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
机组关机定时器和控制逻辑图
Instructions:
Unit shutdown timer and
control logic diagram
22
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
LED
DATA ECU
23
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
根据电气原理图设置数
字量输入口
Instructions:
Set the digital input
port according to the
electrical schematic
24
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
根据电气原理图设置数
字量输出口
Instructions:
Set the digital output
port according to the
electrical schematic
25
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
Load/Stopping Timers
Start Timers
26
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
根据实际发电机状态设
置。
Instructions:
Set according to the
actual generator
status.
27
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
发电机额定电压、欠压、
过压设置
Instructions:
Generator rated
voltage,
undervoltage,
overvoltage Settings
28
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
发电机额定频率、欠频、
过频设置
Instructions:
Generator rated
frequency,
underfrequency,
overfrequency Settings
29
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
根据实际发电机配置进行设置
Instructions:
Set according to the actual
generator configuration
30
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
根据发电机组的额定功
率设置。
Instructions:
Set according to the
rated power of the
generator group.
31
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
逆功报警设置为额定功
率的 8%
Instructions:
The reverse power
alarm is set at 8% of
the rated power
32
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
根据项目的特殊要求编辑 PLC 程序
例如,机油预供应逻辑
Instructions:
Edit the PLC program according to
the special requirements of the
project
For example, oil pre-supply logic
33
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
根据设备性能进行微调
Instructions:
Fine-tune according
to unit performance
34
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
说明:
微调负载分配响应
Instructions:
Fine-tune the load
distribution response
35
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
深海控制器常用功能及注意事项: Common functions and precautions:
1 、 DSE 深海 6120 、 7320 、 8620 控制器可提供两种自启动方式: AMF 市电检测和远程带载启
动(无源触点),可根据客户现场需求,灵活选择和设置。
1. DSE deep-sea 6120, 7320 and 8620 controllers can provide two self-starting modes:
AMF mains detection and remote on-load start (passive contact), which can be flexibly
selected and set according to customer site needs.
36
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
2 、更换新 DSE 深海控制器时,注意以下刷写事项:
2.When replacing the new DSE deep-sea controller, pay attention to the following flashing
matters:
6 系列和 7 系列控制器程序刷写时,可直接将导出的原始程序写入到新控制器内。注意程序的
版本要和控制器的版本匹配。 When flashing programs to Series 6 and Series 7
controllers, the exported original programs can be written directly to the new
controller. Note that the version of the program should match the version of the
controller.
8 系列控制器程序刷写时,监控里的信息无法写入到新控制器内部,需要在程序写入后,重新
进去监控页面,找到以下 3 点重新设置: When the program of the 8 series controller is
flashed, the information in the monitoring cannot be written to the new controller, you
need to re-enter the monitoring page after the program is written, and find the
following three points to reset the settings:
37
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
① ② ③
① 监控—发电机—多个— IP 地址和优先级重新设置
② 监控—发电机—调速器和调压板的 SW1 和 SW2 重新设置
③ 同步—负载控制的 PID 重新设置。
38
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
3 、 DSE 深海所有控制器型号都支持事件记录功能,查看方式分为:控制器面板查看和控制器监控
页面的事件记录导出查看,最多可以记录 250 条事件记录。
3. All DSE deep-sea controller models support the event recording function, and the
viewing methods are divided into: viewing on the controller panel and exporting and
viewing the event records on the controller monitoring page, and up to 250 event records
can be recorded.
39
2 控制器软件安装、设置及使用注意事项
Module Software Installation & Setting
4 、 DSE 深海 6 系列、 7 系列、 8 系列控制器都有数据记录功能,在设置软件“控制器”的”数据
记录中“可以设置要记录的事件数据,最多同时可记录 20 个,打开”工具“的”数据记录观测”,
可将数据导出。
4. DSE deep-sea 6 series, 7 series and 8 series controllers all have data recording function,
in the "data recording" of the setting software "controller", you can set the event data to
be recorded, up to 20 can be recorded at the same time, open the "data recording
observation" of the "tool", and the data can be exported.
40
41